|
| 1 | Wiring for light point/fan point/exhaust fan /Call bell point with 1.5 sq mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface casing caping and earthing the light point with 1.5 Sq.mm HRFRLS/PVC pipe insulated single core copper conductor cable as required. Group 'C'. (5/6 Amp) |
| 2 | Supplying and fixing Metal Box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 Amps. Socket outlet and 15/16 Amps. Paino type switch, connections, painting etc as required . |
| 3 | Providing Wiring for light power plug with 2x1.5 sq.mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No. 1.5 Sq.mm HRFLRS/PVC insulated single core copper conductor cable for earthing as required. |
| 4 | Providing Wiring for light power plug with 2x4 sqmm PVC insulated heat resistant flame retardant (HRFLR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No. 4 Sq.mm HRFLRS/PVC insulated single core copper conductor cable for earthing as required. |
| 5 | Providing Wiring for light power plug with 4x4 sqmm PVC insulated heat resistant flame retardant (HRFLR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 2 No. 4 Sq.mm HRFLRS/PVC insulated single core copper conductor cable for earthing as required. |
| 6 | Supplying and fixing brass batten/angle holder including connections etc as required. |
| 7 | Providing, installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc.as required : Ceiling Fan 1200mm sweep, Category-A. |
| 8 | Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required : Single pole Cat-A. |
| 9 | Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required : Doudble pole Cat-A. |
| 10 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc.as required. 63 Amps.Cat-A. |
| 11 | Supplying and fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB) having a sensitivity current up to 300 millampers in the existing MCB DB complete with connections, testing and commissioning etc as required : 63 Amps. Cat-A. |
| 12 | Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and power painted, including earthing etc. as required:- |
| 13 | Singal door-12 way |
| 14 | Providing, fixing of 2x9 Watt LED lamp complete in all leads and lifts as per direction and to the entire satisfaction of Engineer in Charge. |
| 15 | Providing and fixing of shock proof rubber mats for electric purposes having one side plain and other side chequered of approved make of size 2 Mtrs x 1 Mtrs and 12.50 mm thick to avoid shock in pump houses complete in all respect and to the entire satisfaction of Engineer-in-Charge. (The weight of shock proof mats should not less then 22Kg per sheet) |
| 16 | Providing and fixing of CUB LED street light BCLST 25W LED pressure die cast housing with epoxy power coated including colour finish Prismatic polycarbonate cover with indivisual LED lenses including 50mm dia 1 No. GMS pipe one meter length bend at suitable angle for fixing & other internal fittings complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 17 | Supplying and errection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron (50mmx50mmx6mm thick) with sufficient numbers of horizontal and vertical intermediate members (25mm x 6mm thick ) flat iron including painting and bonding to the existing earth as required Please Enable Macros to View BoQ information |
