|
| 1 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, Hard/dense soil complete all as specified and as directed |
| 2 | Excavating in trenches n. exc. 1.5 m. wide and n. exc. 1.5 m. in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pire holes, etc. n. exc. 10 sqm on plan and not exc. 1.5 m. in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 3 | Returning filling in, including spreading leveling,watering and well ramming in layers n.exc 25m in soft/loose soil complete all as specified and as directed |
| 4 | Removing excavated materials to adistance n.exc 50mm and depositing where directed at a level n.exc 1.5 M above the starting point in soft/loose soil complete all as specified and as directed |
| 5 | M&L for Plain Cement Concrete Type D2 (1:4:8) (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed |
| 6 | M&L for Brick work with sub-class `B' bricks, straight or curved on plan 6 M mean radius built in cement mortar (1:4) complete all as specified and as directed |
| 7 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) and finished fair and even without using extra cement complete all as specified and as directed |
| 8 | M&L for 100 mm thick Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in sub base complete all as specified and as directed |
| 9 | M&L for screed bed or bedding layer 15 mm thick in cement mortar (1:4) on floors for laying floor finish complete all as specified and as directed. |
| 10 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed with grey cement and no pigment and pointed in neat cement slurry in floors all as specified and as directed incl taking down old one |
| 11 | M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed |
| 12 | S & F MS steel work in tubular trusses and tubular posts and square tubes including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and as directed |
| 13 | M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed |
| 14 | S&F Polycarbonate corrugated Profiled sheet Solid corrugated roofing sheets material -embossed/ compact thickness 3mm colour clear/Bronze / opal white Application : roofing light sheet skylight, lighting for room corrugated sheeting with two corrugations side lap fixed with self tapping screw and washer in roof, wall etc complete all as specified and as directed |
| 15 | S&F Polycarbonate hollow sheet 10mm thick of an colour having tensile strength of 60.30 Mpa as in roof covering / clading to wall , fixed with self tapping screwed including aluminium channel strip complete all as specified |
| 16 | Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 17 | S&F new sheet glass 4.8 mm thick ordinary quality and glazing with oil putty or glazing pins / spring clip in square, rectangle n exc 0.5 sqm in each pan all as specified and as directed. |
| 18 | Supply and fixing factory made uPVC Frame with shutter white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. (Glass shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 19 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified. |
| 20 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.45mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall fixed with self tapping screws complete all as specified and directed. |
| 21 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensil strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Please Enable Macros to View BoQ information |
| 22 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensil strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Please Enable Macros to View BoQ information |
