|
| 1 | M & L taking out and dismanteling of mono block fountain pump set openwell any type of Cap 5 HP, 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, transporataion to workshop & dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after following repairs as directed by Engineer-in-charge :-Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under item |
| 2 | Supply only bush with oiling and gresing as required. |
| 3 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 4 | Cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles mechanical oil seal with oil etc. complete all as specified and directed. |
| 5 | M & L for transporataion & dismanteling of centrifugal pump set of Cap 7.5 to 10 HP 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors in proper manner and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after repairs as directed by Engineer-in-charge Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under relevant items of BOQ. |
| 6 | Supply only bush with oiling and gresing as required. |
| 7 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 8 | Shaft sleeve bronze as per existing |
| 9 | supply only shaft metallic coupling with key. |
| 10 | M & L for transporattaion & dismanteling of centerifugal pump set of Cap 20 HP 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors in proper manner and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after following repairs as directed by Engineer-in-charge :-Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under item |
| 11 | supply only bush with oiling and gresing as required. |
| 12 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 13 | Supply only damaged star rubber coupling as per existing |
| 14 | Shaft sleeve bronze as per existing |
| 15 | supply only shaft metallic coupling with key. |
| 16 | M & L for transporataion & dismanteling of centerifugal pump set of Cap 40 HP 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors in proper manner and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after following repairs as directed by Engineer-in-charge.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under relevant item of BOQ. |
| 17 | supply only bush with oiling and gresing as required. |
| 18 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 19 | Supply only damaged star rubber coupling as per existing |
| 20 | Supply only gun metal impeller as per existing. |
| 21 | Shaft sleeve bronze as per existing |
| 22 | supply only shaft metallic coupling with key as per existing. |
| 23 | Supply only stainless steel shaft as per existing |
| 24 | M & L for transporataion & dismanteling of centrifugal pump set of Cap 50 HP 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors in proper manner and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after following repairs as directed by Engineer-in-charge.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under relevant item of BOQ. |
| 25 | supply only bush with oiling and gresing as required. |
| 26 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 27 | Supply only damaged star rubber coupling as per existing |
| 28 | Shaft sleeve bronze as per existing |
| 29 | supply only shaft metallic coupling with key as per existing. |
| 30 | Supply only stainless steel shaft as per existing |
| 31 | M&L for transporataion & dismantling of existing defective induction motor of the Pumpset capacity 50 HP, 03 phase, 415 Volt sizes from the foundation, disconnecting the electric connection, coupling joint and transporting to workshop for cutting down and removing existing burnt copper windings, clenining of slots and rewinding with supper enameled copper conductor complete including varnishing, drying, ovening, overhauling, greesing, necessary lathe work and replacement of bearing and fixing in the original position, making neccessary electric connection and coupling connection and testing of induction motor complete all as specified and as directed by Eng in charge |
| 32 | ,---ditto--- all as per Item No 6 but Induction motor of Pumpset cap 40 HP, 03 phase, 415 Volt complete. |
| 33 | ,---ditto--- all as per Item No 6 but Induction motor of Pumpset cap 20 HP, 03 phase, 415 Volt complete. |
| 34 | ,---ditto--- all as per Item No 6 but Induction motor of Pumpset cap 7.5 HP, 03 phase, 415 Volt complete. |
| 35 | M & L taking out and dismanteling of openwell submersible pump set with motor of Cap 20 HP, 3 phase, 415 volts, 50Hz, AC supply after disconnecting electric connection, transporataion to workshop & dismanteling of pump for repairing/ replacing defective parts as ordered, re-assembling, alignment of pumps and motors and testing including replacing worn out nuts, bolts, washers, Lathe machine work complete and lowering the same and reconnecting to pipe line and electric connection after following repairs as directed by Engineer-in-charge :-Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under item . |
| 36 | supply only bush with oiling and gresing as required. |
| 37 | Supply only ball bearing as per existing. Make:- NBC/SKF/TATA |
| 38 | Supply only pump shaft as per existing |
| 39 | Cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles mechanical oil seal with oil etc. complete all as specified and directed. |
| 40 | M & L for transporataion & lifting out submersible pump set of Capacity 7.5 HP, 3 phase, 415 volts, 50Hz, AC supply along with column pipe of any size from the bore well after disconnecting electric connection, dismantling of pump and motor for repairing/ replacing defective parts as ordered, oiling, greasing as required and re-assembling and testing including replacing worn out nuts, bolts, washers complete and lowering the same after repairing and making electrical and delivery pipe connections complete all as specified and directed.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under relevant item of BOQ. |
| 41 | Supply only stainless steel pumpshaft as per existing |
| 42 | Supply only gun metal impeller with neck key and distance bush. |
| 43 | Supply only Shaft bush as per existing |
| 44 | Supply only thrust bearing with plate of pump as per existing |
| 45 | Supply only rubber gasket 3mm thick of any size as per existing |
| 46 | Cutting of burnt winding and rewinding the stator with PVC insulated copper wire as per existing size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as specified and directed. |
| 47 | M & L for transporattaion & taking out / lifting out of submersible pump set of Capacity 10 HP, 3 phase, 415 volts, 50Hz, AC supply along with column pipe of any size from the bore well after disconnecting electric connection, dismantling of pump and motor for repairing/ replacing defective parts as ordered, oiling, greasing as required and re-assembling and testing including replacing worn out nuts, bolts, washers complete and lowering the same after repairing and making electrical and delivery pipe connections complete all as specified and directed.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under relevant item of BOQ. |
| 48 | Supply only stainless steel pumpshaft as per existing |
| 49 | Supply only gun metal impeller with neck key and distance bush |
| 50 | Supply only Shaft bush. |
| 51 | Supply only thrust bearing with plate of pump as per existing |
| 52 | Supply only rubber gasket 3mm thick of any size as per existing |
| 53 | Cutting of burnt winding and rewinding the stator with PVC insulated copper wire as per existing size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as specified and directed. |
| 54 | M & L for transporataion & taking out / lifting out of submersible pump set of Capacity 12.5 HP, 3 phase,415 volts, 50Hz, AC supply along with column pipe of any size from the bore well after disconnecting electric connection, dismantling of pump and motor for repairing/ replacing defective parts as ordered, oiling, greasing as required and re-assembling and testing including replacing worn out nuts, bolts, washers complete and lowering the same after repairing and making electrical and delivery pipe connections complete all as specified and directed.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under item |
| 55 | Supply only stainless steel pumpshaft. |
| 56 | Supply only gun metal impeller with neck key and distance bush. |
| 57 | Supply only Shaft bush. |
| 58 | Supply only thrust bearing with plate of pump |
| 59 | Supply only rubber gasket 3mm thick of any size as per existing complete all as specified and directed. |
| 60 | Cutting of burnt winding and rewinding the stator with PVC insulated copper wire as per existing size and class of insulation including insulation paper, sleeves, thimbles etc. |
| 61 | S&F in repair single phase starter suitable for 3 HP 240 volts AC supply, relay range 25 to 30 Amp, combine V/A meter, voltmeter selector switch, rocker switch, Single phase preventor, IP 54 protection, ON/OFF indication, complete all as specified and directed. |
| 62 | S&F in repair DOL starter for 10 HP suitable for 3 phase, 415 volts AC supply, relay range 13 to 21 Amp, power contactor 32 amp, combine V/A meter, voltmeter selector switch, ON/OFF indication, IP 54 protection, Single phase preventor complete all as specified and directed. |
| 63 | S&F in repair of fully automatic star delta starter suitable for 20 HP Capacity, 3 phase 415 V AC supply, relay range 20A to 32 A , power contactor 32A, combine V/A meter, voltmeter selector switch, single phase protection, IP 54 protection, ON/ OFF indication complete all as specified and directed. |
| 64 | S&F in repair of fully automatic star delta starter 25 HP, relay range 30 to 50 Amp, 3 phase 415 V AC supply, conactor 50A, combine V/A meter, voltmeter selector switch, single phase protection, IP 54 protection, ON/ OFF indication complete all as specified and directed. |
| 65 | S&F in replacement of soft starter of size 294.6 x 156.4 x 192.2 mm of capacity up to 40 HP centrifugal pump in exising panel and taking down unsv complete all as specified and directed.. (Make:- L&T Cat No. EMX3-0053B-411 or equivalent in ABB/ Siemen as approved by GE.) |
| 66 | S&F in replacement of of soft starter of size 294.6 x 156.4 x 192.2 mm of capacity up to 50 HP centrifugal pump in exising panel and taking down unsv complete all as specified and directed. (Make:- L&T Cat No. EMX3-0076B-411 or equivalent in ABB/ Siemen/ Schneider as approved by GE.) |
| 67 | S&F in replacement copper cable multistranded conductor unarmoured 25 Sqmm 3 core 1100 v grade PVC insulated sheathed along with proper lugs complete all as specified and directed. |
| 68 | S&F in repair MCCB TPN (4 pole) 63 Amp , 415 volts, 50 Hz 16 KA including taking down unsv complete all as specified and directed. |
| 69 | S&F in repair MCCB TPN (4 pole) 100 Amp , 415 volts, 50 Hz 16 KA including taking down unsv complete all as specified and directed. |
| 70 | S&F in repair MCCB TPN (4 pole) 200 Amp , 415 volts, 50 Hz 36 KA including taking down unsv complete all as specified and directed. |
| 71 | S&F in repair MCCB TPN (4 pole) 250 Amp , 415 volts, 50 Hz 36 KA including taking down unsv complete all as specified and directed. |
| 72 | S&F in repair MCCB TPN (4 pole) 400 Amp , 415 volts, 50 Hz 36 KA including taking down unsv complete all as specified and directed. |
| 73 | Supply & fix straight through heat shrinkable cable jointing kit suitable for 1.1 KV, 3.5 core XLPE / PVC armoured aluminium conductor cable of 35 Sqmm to 50 Sqmm size grade cable complete with jointing material and accessories including necessary earth work complete all as specified and directed. |
| 74 | S&F in replacement of power contactor of capacity 20 Amp, 4 pole 415 Volt, as per existing complete all as specified and directed. |
| 75 | S&F in replacement of power contactor of capacity upto 32 Amp, 4 pole 415 Volt , as per existing complete all as specified and directed. |
| 76 | S&F in replacement of power contactor of capacity 40 Amp, 4 pole 415 Volt, as per existing complete all as specified and directed. |
| 77 | S&F in repair for electronic star delta 160 -500 V for 3-30 sec timer as per existing complete all as specified and directed. |
| 78 | S&F in repair for voltage slector switch for starter & LT Panel as per existing complete all as specified and directed. |
| 79 | Supply & fix in replacement thermal overload Relay 3 phase 415 volt 50 Hz, thermal release range 1.5-3 Amp complete all as specified and directed. |
| 80 | Supply & fix in replacement thermal overload Relay 3 phase 415 volt 50 Hz, thermal release range 9. - 14 Amp complete all as specified and directed. |
| 81 | Supply & fix in replacement thermal overload Relay 3 phase 415 volt 50 Hz, thermal release range 13-20 Amp complete all as specified and directed. |
| 82 | Supply & fix in replacement thermal overload Relay 3 phase 415 volt 50 Hz, thermal release range 22-30 Amp complete all as specified and directed. |
| 83 | Supply & fix in repair for single phase preventor 380 to 415 Volt as per existing complete all as specified and directed. |
| 84 | Supply & fix in repair for ampere meter with CT,s of range 0-60 amps as per existing complete all as specified and directed. |
| 85 | Supply & fix in repair for voltmeter with PT,s of range 0-500 volts as per existing complete all as specified and directed. |
| 86 | S&F in repair MCB TP of capacity 25 to 63 Amp, 'c' series 415 volts, as per existing complete all as specified and directed. |
| 87 | S&F in replacement of old U/S gland packing with new to the Pump set of any sizes/capacity complete with neoprene rubber gasket, jointing material and incl nuts/bolts/washer of suitable size etc complete all as specified and directed. |
| 88 | Supply and fix in repair MS nuts, bolts with washer of any size as per site condition complete all as specified and directed. |
| 89 | S&F in repair 80mm bore size GI heavy grade column pipe (ISI marked), both side flanged and welded (Each of 3 m length) including taking out old corroded column pipe both side flanged complete all as specified and directed. |
| 90 | ,---ditto--- all as per srl item No 42 above but 65 mm bore pipe complete. |
| 91 | ,---ditto--- all as per srl item No 42 above but 50 mm bore pipe complete. |
| 92 | S&F heat shrinkable cable jointing kit suitable for submersible cable of 1100 volts grade, 4/6/10 sqmm 3 core, complete with jointing material and accessories complete all as specified and directed. |
| 93 | Supply only submersible copper cable PVC insulated over all sheethed flat ISI marked, 1100 volts grade of 4 sqmm 3 core complete all as specified and directed. |
| 94 | Supply only submersible copper cable PVC insulated over all sheethed flat ISI marked, 1100 volts grade of 6 sqmm 3 core complete all as specified and directed. |
| 95 | Labour only ( Electrician) for checking the serviceability of the different spares/ component/ parts of the starter and motor pump set/ panel/ phase sequential of any capacity at site complete all as directed by Engr-in-charge |
| 96 | M & L for Dismanteling of pressure pump set of cap upto 0.5 HP, single phase, 230 volts, 50Hz, AC supply after disconnecting electric connection, repairing/ replacing defective parts as ordered, re-assembling and testing including replacing worn out nuts, bolts, washers, bearing etc complete and electric connection after following repairs as directed by Engineer-in-charge.Note : - (i) The spare part required for replacement shall be measured & paid for separately as supply only under item |
| 97 | M & L for transportation of 0.5 HP motor winding for Cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as specified and directed. |
| 98 | Supply and fix in replacement of changover switch 200 Amp, 415 volts, 4 pole off load with sheet enclouser suitable complete all as specified and directed. |
| 99 | Supply and fix in replacement of universal pressure switch in existing pressure pump complete all as specified and directed. |
| 100 | S&F in repair pressure pump of capacity 0.5 HP single phase 230 volts 50 HZ AC supply including all electric connection to the nearest pont, testing and commissioning Complete as directed and specified by Engineer-in-charge. Make :- KSB or equivelent as approved by GE |
| 101 | S & F in replacement of CI foot valve of size 150 mm with gun metal working parts, ISI marked with all fittings all as specified and directed by EIC |
| 102 | ,---ditto--- all as per item No 54 above but 100 mm size complete all as specified and directed. |
| 103 | ,---ditto--- all as per item No 54 above but 80 mm size complete all as specified and directed. |
| 104 | Providing area cleaning/sweeping of preimises water supply installation (Ph House) including cutting out green vegetation, roots, bushes, Tree branches ,picking polothineand other unwanted material from the installation area and maintaining the ground surrounding the installation and removing the same out side the defence area as directed by Engr in charge. The approx area of installation kept clean all as under. (1) PH haldi ghati -6500 Sqm (2) Sub area booster pump house - 5200 Sqm (3) 61 Cav OHT - 900 Sqm (4) Signal Pump house-6100 Sqmm (5) Rajendra chauk OHT - 400 Sqm (6) APS OHT - 1000 Sqm (7) JCO/OR OHT - 2500 Sqm (8) Comd Camp OHT - 900 Sqm (9) Comand Pump house - 5200 Sqmm (10) Borewell at Comd gate 2, Near railway phatak, New PH 02, Ph 04, Sub area near Booster ph, Comand camp, Sub area Officer mess - 6500 Sqm (11) khatipura Ph - 9200 Sqm (12) Para 3 Ph - 1200 SqmNote :- (i) if contractor fails to clean the area of installation compete in all respect else recovery @ 500 per job shall be recovered from his dues and contractors claim shall not enter on this account. (ii) Contractor provide required T&P like as(Broom, Axe,saw,boucket etc) (iii) Contractor will resposible to maintain the pump house area clean for contract peroid. |
| 105 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil including trimming of tree roots in trenches complete all as specified and directed. |
| 106 | Returning, filling-in, including spreading, watering and well ramming in layers not exceeding 25 cm thick each, in soft /loose soil complete all as specified and directed. |
| 107 | Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 108 | M & L Sand cushioning to PVC under ground cable with screened and washed tibba sand (non cohessive) and punning to provide a required cover complete all as specified and directed. Note : Punned thickness shall only be measured for payment. |
| 109 | M & L Bricks for protection cover to under ground cable (with old size sub class ‘B’ bricks) laid flat abutting each other with width of protection being equal to length of brick. The gap between adajcent bricks shall not exceed 10 mm as directed by Engineer-in-Charge. |
| 110 | M&L for PCC (1:3:6) type C1 using 20 mm graded aggregate for making good the disturbed portion of road/floor/platform etc including form work and compaction etc complete all as specfied and directed . |
| 111 | M&L for boring of existing road/path for laying of GI pipe for protection of cable under road including making good distrubed area/surface all as directed by Engr in charge |
| 112 | Supply, Laying, Jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on pole of size 16 Sqmm 4 core including taking down old unserviceable cable complete all as specified and directed |
| 113 | Supply, Laying, Jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on pole of size 25 Sqmm 3 ½ core including taking down old unserviceable cable complete all as specified and directed |
| 114 | Supply, Laying, Jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on pole of size 50 Sqmm 3 ½ core including taking down old unserviceable cable complete all as specified and directed |
| 115 | Repair & maintenance of existing header, welding work, jointing of pipe ,butter fly valve etc of header as per eixsting shape upto 50 mm to 600 mm bore pipe complete all as specified and directed. |
| 116 | S&F in repair for sluice valves, class PN 1.6 of 80mm bore size with cast iron body, non rising type and cast iron wheel head, both ends flanged, IS-14846 marked comlete with neoprene rubber gasket, jointing material and incl nuts / bolts / washer of suitable size etc including taking down old unsv complete all as specified and directed. |
| 117 | ,---ditto--- all as per srl item No. 69 above but of size 100 mm bore complete. |
| 118 | ,---ditto--- all as per srl item No. 69 above but of size 150 mm bore complete. |
| 119 | ,---ditto--- all as per srl item No. 69 above but of size 200 mm bore complete. |
| 120 | S&F in repair for dual plate check non return valves, class PN 1.6 of 50mm bore size with cast iron body double disc of CS, Hinge pin, plate bearing, plugs of SS 410 and spring of SS316 and both ends flanged, ISI marked comlete with neoprene rubber gasket ,jointing material, connected with existing MS pipe by jointing through flanged and welding work, rubber gasket, nuts/bolts/washer of suitable size etc including taking down old unsv complete all as specified and directed. |
| 121 | S&F in repair for dual plate check non return valves, class PN 1.6 of 80mm bore size with cast iron body double disc of CS, Hinge pin, plate bearing, plugs of SS 410 and spring of SS316 and both ends flanged, ISI marked comlete with neoprene rubber gasket ,jointing material, connected with existing MS pipe by jointing through flanged and welding work, rubber gasket, nuts/bolts/washer of suitable size etc including taking down old unsv complete all as specified and directed. |
| 122 | S&F in repair for dual plate check non return valves, class PN 1.6 of 100mm bore size with cast iron body double disc of CS, Hinge pin, plate bearing, plugs of SS 410 and spring of SS316 and both ends flanged, ISI marked comlete with neoprene rubber gasket ,jointing material, connected with existing MS pipe by jointing through flanged and welding work, rubber gasket, nuts/bolts/washer of suitable size etc including taking down old unsv complete all as specified and directed. |
| 123 | S&F in repair for dual plate check non return valves, class PN 1.6 of 150mm bore size with cast iron body double disc of CS, Hinge pin, plate bearing, plugs of SS 410 and spring of SS316 and both ends flanged, ISI marked comlete with neoprene rubber gasket ,jointing material, connected with existing MS pipe by jointing through flanged and welding work, rubber gasket, nuts/bolts/washer of suitable size etc including taking down old unsv complete all as specified and directed. |
| 124 | Supply only calcium based high strength granular chlorination chemical (calcium hypochlorite having chlorine 65% to 70% ) for water treatment. Granular material shall be free of foreign material decomposing at 177 C soluble in water and alcohol not hygroscopic practically clear in water solution at saturation level. The material should not contain more than 5% to 10 % moisture. Granular size should be as follows:- Mesh passing through -100 BSS 1.5 % maximum iron as Fe 0.05% maximum Mn 40 PPM maximum Mol wt 142.98, Toxicity :Oral rate LD 50-850 mg/kg. duly tested from approved laboratory packed in a fibre drum duly sealed granular type from manufacturer or authorised dealer/distributor complete all as specified and directed. Note- Brand name/batch number and complete particulars of manufacturer should be printed on the container/packing. Please Enable Macros to View BoQ information |
| 125 | Supply only calcium based high strength granular chlorination chemical (calcium hypochlorite having chlorine 65% to 70% ) for water treatment. Granular material shall be free of foreign material decomposing at 177 C soluble in water and alcohol not hygroscopic practically clear in water solution at saturation level. The material should not contain more than 5% to 10 % moisture. Granular size should be as follows:- Mesh passing through -100 BSS 1.5 % maximum iron as Fe 0.05% maximum Mn 40 PPM maximum Mol wt 142.98, Toxicity :Oral rate LD 50-850 mg/kg. duly tested from approved laboratory packed in a fibre drum duly sealed granular type from manufacturer or authorised dealer/distributor complete all as specified and directed. Note- Brand name/batch number and complete particulars of manufacturer should be printed on the container/packing. Please Enable Macros to View BoQ information |
