|
| 1 | CHAIR VARANDAH FD-1031,359 |
| 2 | Removing of old cane from chair varandah steel (bottom and back) and re-canning with new best quality plastic cane 4mm wide, white colour complete all as specified and directed. |
| 3 | M&L for painting to frame of chair varandah with white synthetic paint after preparation of surface (after removing the old cane) complete all as specified and directed. |
| 4 | M&L for gas welding to frame of chair varandah including preparation of surface and removing the unwanted welding spot complete all as specified and directed. |
| 5 | S&F in replacement of unserviceable portion of frame of chair varandah with 20mm conduit pipe of wall thickness 1.60mm duly gas welding complete all as specified and directed. |
| 6 | S&F in replacement of hard rubber shoe to the leg of chair varandah of standerd approved quality complete all as specified and directed. |
| 7 | Revolving Chair Geeken, TP, FD/E6/MAP/01 |
| 8 | Removing old unserviceable Seat of Revolving chair and supply & fixing New seat of computer chair all as per drawing. Seat shall be made of 50 mm thick synthetic foam of 32 density fixed over 12 mm thick plywood commercial and shall be stitched with superior quality fabric cloth of approved shade complete all as specified and directed. |
| 9 | Removing old unserviceable back of Revolving chair and supply & fixing new back of computer chair all as per drawing . Back shall be 25 mm thick respectively synthetic foam of 32 density fixed over 12mm thick plywood commercial and shall be stitched with superior quality fabric cloth of approved shade complete all as specified and directed. |
| 10 | Removing old unserviceable cover cloth of (seat and back) from existing Revolving chairs. S & F of new fabric cloth duly approved by GE, shall be used for seat and back of existing chair computer complete all as specified and directed. |
| 11 | Removing old unserviceable Arms rest of Revolving chair and supply & fixing new arms rest of computer chair all as per drawing and complete all as specified and directed.Note : Arm Rest shall be polyurethene \\"D\\" shape. |
| 12 | Removing old unserviceable Revolving wheels of revolving chair and supply & fixing New Revolving Wheel of computer chair all as per drawing and directed |
| 13 | Removing old unserviceable padestal Assembly and supply & fixing New Steel Padestal Assembly of Revolving Chair all as per drawing and complete all as specified and directed. |
| 14 | Removing old unserviceable Hydroclic System gas lift (Air soft) and supply & fixing of New Hydrolic System (Air Soft) of Revolving chair all as per drawing and complete all as specified and directed. |
| 15 | GI PIPE CHARPOY NEWAR INTO GI PIPE PLYTOP FD-220(M), 227 :- |
| 16 | Removing of old unserviceable plytop / newar from GI charpoy and supply & fixing two Nos stiffners made out of MS square pipe size 25mm x 25mm x 1.5mm conforming to IS-2062 of 1999 Grade 'A' (weight of pipe not less than 1.06 kg/mtr). The stiffners shall be welded to the frame of the GI charpoy at equal distance joining the long rail such that they lie parallel to short rails and perpendicular to the long rail. The stiffners shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 17 | Removing old unserviceable plywood from charpoy plytop and welding of old broken stiffners pipe and re-fixing plywood in charpoy complete all as specified and directed. |
| 18 | Removing of old unserviceable long rails having both threaded broken end and supply & fixing new long rail made out of GI tubing 32mm bore mediam grade ISI marked including making threaded both ends and fixing as shown on drawing complete all as specified and directed. |
| 19 | Removing of old unserviceable short rails of GI charpoy having both threaded broken ends and supply & fixing new short rails of GI charpoy obtained from Srl Item No 7(c) above, including making threads at the both ends and fixing as shown on drawing complete all as specified and directed. |
| 20 | Removing of old unserviceable leg and supply & fixing new leg made out of short rail of GI charpoy obtanied from Srl item No. 7 (d) above, including welding of MS plate at the bottom of leg and making thread other end & fixing in position complete all as specified and shown on drawing. |
| 21 | Removing of old unserviceable GI elbow three way and supply & fixing of new GI elbow three way size 32mm bore with new ISI mark (weight not less than 420 gms each and re-assembling of GI Charpoy after replacement of broken elbow complete all as specified and directed. |
| 22 | Removing old unserviceable check nuts from long rail of GI charpoy and supply & fixing of new check nut of 32mm bore and 10mm wall thick, (Wt not less than gms each) ISI marked and fixing in the same in position complete all as specified and directed. |
| 23 | Supply & fixing new 12mm thick plywood in repairs ISI marked BWR Grade of approximate size 1980mm x 1050mm conforming to IS-303/1989 on top of GI pipe charpoy fixing with 10 Nos new nut, bolt and washer of suitable size after re-tightining of all joints of charpoy all as specified and directed.(Note:- Each corner of plywood should be round shaped). |
| 24 | TABLE BED SIDE FD/E-6/MAP/15® |
| 25 | Removing Old unserviceable top 18 mm thick prelaminated particles board exterior grade and supply & fixing new top including PVC beading all round as per drawing and complete all as specified and directed. |
| 26 | Removing old unserviceable sides 18 mm thick prelaminated particle board exterior grade and supply & fixing new sides including PVC beading all round as per drawing and complete all as specified and directed. |
| 27 | Removing old unserviceable top back 18 mm thick prelaminated particle board exterior grade and supply & fixing new top back including PVC beading all round as per drawing and complete all as specified and directed. |
| 28 | Removing old unserviceable drawers and supply & fixing new drawers (including necessary T/W runner ) as per drawing complete all as specified and directed. |
| 29 | Removing old unserviceable back 6 mm thick plywood and supply & fixing new back 6 mm thick BWR plywood as per drawing and complete all as specified and directed. |
| 30 | Removing old unserviceable hard rubber shoes of table bed side and supply & fixing in replacement of hard rubber shoes of table bed side all as per drg and complete all as specified and directed. |
| 31 | M & L for painting of frame of table bed side with two coats of synthetic enamel black paints including welding where required and preparation of surfaces complete all as specified and directed. |
| 32 | Material and labour for re-painting of mentioned below steel furnituire as per the following steps:-(a) Denting of bent surfaces with the help of hammer in best workmanship manner.(b) Removing old paint by scrubbing with sand paper 150 No thoroughly.(c) Applying one coat of metal primer. (Make Asian/Nerolac/Delux).(d) Applying metal putty to even surface.wait period 2-3 hours to be given for putty to set and dry completely. scrub off the excess putty with 150 No and paper and spraying little amount of water simultaneously.(e) Wipe the surface with solt dry cloth and apply one coat of enamel paint of light shade as approved by GE. |
| 33 | Almirah large steel with shelves complete all as specified and directed. FD-1031/67 |
| 34 | Almirah small steel with shelves complete all as specified and directed. FD-1032/243 |
| 35 | Locker bed side steel complete all as specified and directed. FD-1029 |
| 36 | Almirah large steel with glazed door complete all as specified and directed. FD-104(M) |
| 37 | Rack adjustable steel 6 tier complete all as specified and directed. FD/106/M |
| 38 | BED HARD STEEL (FD/E6/MAP/08(R) |
| 39 | Supply and fixing new 18mm thick both sides prelaminated particle board BWR exterior grade confirming to IS in replacement of UNSV 18mm thick both sides pre-laminated particle board of BWR exterior grade confirming to relevant IS shade /colour as approved with PVC edging screwed to MS strip of head board all as per drawing complete all as specified and directed. |
| 40 | Supply and fixing new 18mm thick both sides prelaminated particle board BWR exterior grade confirming to IS in replacement of UNSV 18mm thick both sides pre-laminated particle board of BWR exterior grade confirming to relevant IS shade /colour as approved with PVC edging screwed to MS strip of foot board all as per drawing complete all as specified and directed. |
| 41 | Supply and fixing in replacement of 20 mm x45mm of 18 gauge MS Strip with new of same size & thickness (including necessaary Welding) all as per drawing and complete all as specified and directed. |
| 42 | M & L for fixing (only) of long rails (including necessary welding /Nut& bolts) to head board and foot board as complete all as specified and directed. |
| 43 | Supply and fixing in replacement of old unserviceable stiffener with new of size 1974x824 mm (including welding ) made of 25 mm x25mm square MS pipe (18 gauge) all as per drawing and complete all as specified and directed. |
| 44 | Supply and fixing 12 mm tick plywood BWR grade type A ,confirming to IS-303 of 1975 (ISI marked) in replacement of old unserviceable 12 mm thick plywood BWR grade type 'A' confirmimg to IS-303 of 1975 (ISI marked) all s per drawing complete all as specified and directed. |
| 45 | Supply and fixing in replacement of old unserviceable hard rubber shoes with new of size 38mmx38mm (Inner size) all as per drawing) complete all as specified and directed. |
| 46 | M & L for painting to frame of bed hard steel with two coats of synthetic enamel black paints including welding where required and preparation of surfaces complete all as specified and directed. |
| 47 | CHAIR DINING |
| 48 | Removing of old unserviceable rear leg of chair dining and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 49 | Removing of old unserviceable front leg of chair dining and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 50 | Removing of old unserviceable front rail/side rail/ back rail of chair dining and supply and fixing with new front rail/side rail/ back rail of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 51 | Removing of unserviceable bottom stiffener of chair dining and supplying and fixing with new bottom stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 52 | Removing of unserviceable back rest of chair dining and supplying and fixing with new back rest of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 53 | Removing of unserviceable cane stiffener of chair dining and supplying and fixing with new cane stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 54 | Removing of old cane from chair dining (bottom) and re-canning with new best quality plastic cane 2mm wide white colour cane in godrej pattern complete all as specified & directed. |
| 55 | M&L for preparation of old/new chair dining and polishing of high gloss french polish of chair dining complete all as specified & directed. |
| 56 | CHAIR WRITING |
| 57 | Removing of old unserviceable rear leg of chair writing and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 58 | Removing of old unserviceable arm rest of chair writing and supply and fixing with new arm rest of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 59 | Removing of old unserviceable front leg of chair writing and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 60 | Removing of old unserviceable front rail/side rail/ back rail of chair writing and supply and fixing with new front rail/side rail/ back rail of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 61 | Removing of unserviceable bottom stiffener of chair writing and supplying and fixing with new stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 62 | Removing of unserviceable cane stiffener of chair writing and supplying and fixing with new cane stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 63 | Removing of old cane from chair writing (bottom) and re-canning with new best quality plastic cane 2mm wide white colour cane in godrej pattern complete all as specified & directed. |
| 64 | M&L for preparation of old/new chair writing and polishing of high gloss french polish of chair writing complete all as specified & directed. |
| 65 | CHAIR EASY |
| 66 | Removing of old unserviceable rear leg of chair easy and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 67 | Removing of old unserviceable front leg of chair easy and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 68 | Removing of old unserviceable front batten of chair easy and supply and fixing with new front batten of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 69 | Removing of old unserviceable back batten of chair easy and supplying and fixing with new batten of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 70 | Removing of old unserviceable arm rest of chair easy and supplying and fixing with new arm rest of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 71 | Removing of old unserviceable front & back rail of seat/back of chair easy and supplying and fixing with new front & back rail of seat/back of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 72 | Removing of old unserviceable side rail of seat/back of chair easy and supplying and fixing with new side rail of seat/back of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg. |
| 73 | Removing of old cane from chair easy (bottom & back) and re-canning with new best quality plastic cane 2mm wide white colour cane in godrej pattern complete all as specified & directed. |
| 74 | M&L for preparation of old/new chair easy and polishing of high gloss french polish of chair dining complete all as specified & directed. |
| 75 | Material and labour for preparing of old/new polished wood based furniture articles as per the following steps:-Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed. Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper (220-320). NOTE: Excess stain should be wiped off before drying and getting absorbed in wood. Step 3 Polishing : Wood will be finished with a good quality french polish (mixture of shellac grains and methylated spirit in ratio 1:10) two to three coats shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required, Polish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed. |
| 76 | Table dining 04/06 person complete all as specified and directed. FD-273, FD-/MAP/-II/03 |
| 77 | Table dining 8 person complete all as specified and directed. FD-273/239 |
| 78 | Teapoy complete all as specified and directed. FD-34 |
| 79 | Table writing complete all as specified and directed. FD-275/249 |
| 80 | Table 3'x2' with drawer complete all as specified and directed. FD-283/224 |
| 81 | Table 3'x2' without drawer complete all as specified and directed. FD-284/223 |
| 82 | Table dressing ladies with mirror complete all as specified and directed. FD-251 |
| 83 | Sofa 3 piece 5 seater complete all as specified and directed. FD-281/258 |
| 84 | Peg Table complete all as specified and directed. FD-277 |
| 85 | Side board complete all as specified and directed. FD-272 |
| 86 | Table center complete all as specified and directed. FD-277 |
| 87 | Hat stand with mirror complete all as specified and directed. FD-361/233 |
| 88 | Sofa Set Four Seater complete all as specified and directed. FD-373 |
| 89 | Table 3'x3' complete all as specified and directed. FD-88(M)/291 |
| 90 | Table Bed Side complete all as specified and directed. FD-210//243/276 |
| 91 | BED PLY TOP:- |
| 92 | Removing of old unserviceable head board plywood of bed ply top (both face) and re-fixing of new plywood 3mm thick complete all as specified & directed and as shown in drg. |
| 93 | Removing of old unserviceable foot board plywood of bed ply top (both face) and re-fixing of new plywood 3mm thick complete all as specified & directed and as shown in drg. |
| 94 | Removing of old unserviceable long rail size 35mm x 90mm of bed ply top and refixing of new first class hard teak wood long rail of size 35mm x 90mm complete all as specified & directed and as shown in drg. |
| 95 | Removing of old unserviceable short rail size 60mm x 60mm of bed ply top and refixing of new first class hard teak wood long rail of size 60mm x 60mm complete all as specified & directed and as shown in drg. |
| 96 | Removing of old unserviceable stiffner rail between to long rails size 40mm x 60mm of bed ply top and re-fixing of new first class hard teak wood stiffeners rail size 40mm x 60mm, made to shape complete all as specified & directed and as shown in drg. |
| 97 | Removing of old unserviceable bend to right angle MS flat iron of bed ply top and re-fixing of new MS flat iron size 35 x 5mm bend to right fixed to corner of bed ply top including preparation of new iron surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed. |
| 98 | Removing of old unserviceable plywood of bed ply top and re-fixing of new best quality commercial type plywood 12mm thick complete all as specified & directed and as shown in drg. |
| 99 | M&L for preparation of old/new plywood of bed ply top and polishing of high gloss french polish of bed ply top complete all as specified & directed. |
| 100 | LOCKER BED SIDE STEEL:- |
| 101 | Removing of old unserviceable hasp and staple and supply & fixing of new CP Hasp and Staple 75mm long as per given in drawing and site requirement complete all as specified and directed. |
| 102 | Removing of old unserviceable stainless steel handle and supply & fixing of new stainless steel handle 100mm long with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 103 | Removing of old unserviceable MS shelf made to shape out of 1mm thick MS sheet and supply & fixing of new MS shelf made to shape out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 104 | Removing of old unserviceable leg of size 600mmx80mmx100mm and supply & fixing of new leg of size 600mmx80mmx100mm made out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 105 | Removing of old unserviceable MS shutter made to shape and supply & fixing of new MS shutter made out 1mm thick to shape as per given in drawing and site requirement complete all as specified and directed. |
| 106 | Charpoy Hard Top (FD/MAP-II/01) |
| 107 | Supply and fixing of stiffener (including welding) made of 25 mm square MS pipe (16 gauge) in replacement of old unserviceable stiffener all as per drawing and complete all as specified and directed. |
| 108 | Supply and fixing of 12 mm thick plywood BWR grade type 'A' of size 1930x850mm confirming to IS -303 of 1975 (ISI marked) in replacement of old unserviceable plywood all as per drawing. complete all as specified and directed. |
| 109 | Supply and fixing of thick hard rubber shoes of size 32 mm square (Inner size) in replacement of unserviceable hard rubber shoe all as per drawing and complete all as specified and directed. |
| 110 | M&L for painting of frame of charpoy with hard top with two coats of synthetic enamel black paints including welding where required and preparation of surfaces complete all as specified and directed. |
| 111 | CHAIR DINING CUSHIONED (MAP) |
| 112 | Removing of old unserviceableb cushion seat of chair dining (MAP) and supply and fixing new cushioned seat of chair dining (MAP) cushioned seat shall be made of 75mm thick & 40 density, cushion fixed on 12mm thick BWR ply which shall be rest on 75mm x 75mm x 25mm teak wood stoppers, stoppers to be fixed at four corners of main frame of chair complete all as specified & directed and as shown in drg. |
| 113 | M&L for preparation of old/new chair dining cushioned (MAP) and polishing of high gloss french polish of chair dining cushioned (MAP) complete all as specified & directed. |
| 114 | ALMIRAH SMALL STEEL WITH SHELVES:- |
| 115 | Removing of old unserviceable MS clamps and supply & fixing of new MS clamps with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 116 | Removing of old unserviceable lock 6 lever and supply & fixing of new lock 6 lever with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 117 | Removing of old unserviceable stainless steel handle and supply & fixing of new stainless steel handle 100mm long with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 118 | Removing of old unserviceable 3 way Locking device with MS rods and cover box and supply & fixing of new 3 way Locking device with MS rods and cover boxs with nut bolts or welding as per give in drawing and site requirement complete all as specified and directed |
| 119 | Removing of old unserviceable MS shelf made to shape out of 1mm thick MS sheet and supply & fixing of new MS shelf made to shape out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 120 | Removing of old unserviceable Base channel of size 485x80x100mm or leg and supply & fixing of new Base channel of size 485x80x100mm to be welded at 50mm from each end of length as per given in drawing and site requirement complete all as specified and directed |
| 121 | Removing of old unserviceable MS shutter made to shape and supply & fixing of new MS shutter made out 1mm thick to shape as per give in drawing and site requirement complete all as specified and directed. |
| 122 | Removing of old unserviceable MS Butt hinges 75mm and supply & fixing of new MS Butt hinges 75mm with nut bolts or welding as per give in drawing and site requirement complete all as specified and directed. |
| 123 | ALMIRAH LARGE STEEL WITH SHELVES:- |
| 124 | Removing of old unserviceable MS clamps and supply & fixing of new MS clamps with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 125 | Removing of old unserviceable lock 6 lever and supply & fixing of new lock 6 lever with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 126 | Removing of old unserviceable stainless steel handle and supply & fixing of new stainless steel handle 100mm long with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 127 | Removing of old unserviceable three way Locking device with MS rods and cover box and supply & fixing of new 3 way Locking device with MS rods and cover boxs with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 128 | Removing of old unserviceable MS shelf made to shape out of 1mm thick MS sheet and supply & fixing of new MS shelf made to shape out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 129 | Removing of old unserviceable Base channel of size 485x80x100mm or leg and supply & fixing of new Base channel of size 485x80x100mm to be welded at 50mm from each end of length as per given in drawing and site requirement complete all as specified and directed. |
| 130 | Removing of old unserviceable MS shutter made to shape and supply & fixing of new MS shutter made to shape as per given in drawing and site requirement complete all as specified and directed. |
| 131 | Removing of old unserviceable MS Butt hinges 75mm and supply & fixing of new MS Butt hinges 75mm with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. |
| 132 | REPAIR TO SIDE BOARD (FD – 26 M) |
| 133 | Replacement of top of side board with 18/19mm thick pre laminated particle board one side teak faced with 6mm thick teak wood edging all-round as per drawing and as specified and directed by the Engineer-in-charge including Taking out old top. |
| 134 | Replacement of door shutter of side board with 18/19 mm thick one side teak faced pre-laminated particle board including one number of CP knob (40 x 40 mm) fixed to each shutter with 6 mm thick teak wood beading all as per drawing and as specified and directed by the Engineer-in-charge including Taking out old shutter. |
| 135 | Replacement of drawer of side board including one number of CP knob of size 40 x 40 mm fixed to each drawer complete as per drawing and as specified and directed by the Engineer-in-charge including Taking out old drawer. |
| 136 | Replacement of back side of side board with 6 mm thick commercial ply wood as per drawing and as specified and directed by the Engineer-in-charge including Taking out back side of side board. |
| 137 | REPAIR TO TABLE DRESSING LADIES (FD-251 &FD-32(M)) |
| 138 | Dismantleing of existing unserviceable ply wood at back of mirror frame and S&F new back of mirror made of 6mm thick plywood bwr type complete all as specified and directed. |
| 139 | All as per srl item No 19.10 above but 12mm ply bwr type on the back of dressing table (box) complete all as specified and directed. |
| 140 | Removing of existing unserviceable looking mirror of table dressing ladies and S&F new mirror 5mm thick complete all as specified and directed. |
| 141 | Dismantling of existing unserviceable aluminum channel of looking mirror and S&F new alluminnium channel complete all as specified and directed. |
| 142 | Dismantling of existing unserviceable front member of drawer of table dressing ladies and S&F new front member made out of 12 mm thick prelaminated particle board exterior grade one side in natural teak face complete all as specifed and direced. |
| 143 | Dismantling of existing unserviceable bottom of drawers of table dressing ladies and S&F new bottom made of ply wood 6 mm thick BWR type ISI mark complete all as shown on drawing and specified and directed. |
| 144 | Dismantling of existing unserviceable broken glass and S&F 5mm thick sliding glass including guide roller complete all as specified and directed |
| 145 | Dismantlig of existing front rail and S&F new front rail of seasoned 1st class teak woood complete all as specifed and direced. |
| 146 | All as per srl item No 19.80 above but side rail complete all as specified and directed. |
| 147 | All as per srl item No 19.80 above but new leg of seasoned teakwood. complete all as specified and directed. |
| 148 | Dismantleing of existing unserviceable knob and S&F of CP knob 25mm dia in square/ round shape complete all as specified and direced |
| 149 | Table dressing gents with mirror (FD-31/230/379) |
| 150 | Removing of old unserviceable box of table dressing gents with mirror and supply and fixing with new box (box shall be made of 12mm thick commercial plywood including 0.8mm thick veneered sunmica, bottom of the box of 12mm thick commercial plywood with sunmica and 3mm thick first class hard teak wood beading in the edge of box) complete all as specified & directed and as shown in drg. |
| 151 | Removing of old unserviceable drawers of table dressing gents with mirror and supply and fixing with new drawers (drawers shall be made of 12mm thick commercial plywood including 0.8mm thick veneered sunmica, bottom and back of the drawers shall be made of 6mm thick commercial plywood without sunmica and 3mm thick first class hard teak wood beading in the edge of box) complete all as specified & directed and as shown in drg. |
| 152 | Removing of old unserviceable plywood of table dressing gents with mirror and supply and fixing with new 6mm thick commercial plywood back side of mirror frame complete all as specified & directed and as shown in drg. |
| 153 | S&F in replacement of knob as per sample approved by GE complete all as specified and directed. |
| 154 | Removing of old unserviceable broken looking mirror of table dressing gents with mirror on wall and supply and fixing of new locking mirror, mirror shall be made of 5mm thick glass with the help of 3mm thick flat iron key plates of MS 25 mm x 25mm in section and machine screw of appropriate size complete all as specified & directed and as shown in drg. |
| 155 | NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.96,302.00] Please Enable Macros to View BoQ information |
