|
| 1 | Lift - MRL typeSupply,Installation Testing & Commissioning of Customised 06 Passenger (G+3) MRL lift at Transit accommodation Allowpora Shopian Phase II (excluding all the civil works). The lift shall be suitable for 06 passengers, of standard design having speed 1m/s serving from Ground, 1st, 2nd & 3rd floor i.e. 04 stops and 04 landings. The elevator shall be of state of art technology, energy efficient drive and all its components/ accessories shall conform to relevant IS standards. • (The Defect Liability Period (DLP) of the equipment shall be 02 years.• Machine – Gearless machine located in the shaft on the top of guiderails• Power Supply – 400/415 V (3 Phase AC)• Control – Simple Collective Selective Control (VF regenerative drive)• Available Hoist way dimensions - to be constructed by civil authorities.• Landing door – Centre door opening in stainless steel hairline.• Door opening :Ground, Ist, 2nd & 3rd floor on same side• Car design - Stainless steel in hairline finish.• Handrail - Round handrail in stainless steel finish provided on rear wall of car.• Alarm button in car operating panel with battery back-up.• Automatic operation for car fan.• Anti-nuisance (empty car)• Anti-nuisance (car call cancellation at direction reversal)• Blower fan in car for ventilation• Braille on push buttons• Door open and door close buttons in car operating panel.• Door closing retries• Door nudging• Emergency light• Full load by-pass• Infra–red screen for car door• Intercom Provision With Instrument• Motor overheat protection.• Overload function with audio-visuals indication in car operating panel.• Phase failure and phase reversal protection.• Automatic rescue device in case of power failure.• Attendant control.Car arrival chime on car top/voice synthesizer.• LCD dot matrix scrolling display in car operating panel.• LCD matrix scrolling display in landing operating panel on all floors.• Fireman control.• Fireman emergency returnThe rates are inclusive of all minor adjustments that may be required in hoistway/pit for completion of the jobProviding & Laying integral Cement based water proofing (Injected type) treatment including preperation of surface and then applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound confirming to IS: 2645. After proper curing apply a second coat of cement slurry admixed with proprietry water proofing compound. The job includes finishing the surface with 20mm thick jointless cement morter of mix 1:4 |
| 2 | Electric WorksSupply, installation, testing & commissioning of 3 Phase-30 KVA Servo-Stabilizer including oil and all allied electrical acessories with earthing.The stabiliser should have following specifications:a) Capacity: 30 KVA, 3-phase unbalanced typeb) Input: (100-265) V AC P-N; (180 - 460) V AC P-Pc) Output: 415 V ± 1% - phase to phase d) Supply: 3 phase, 4 wires, 50Hze) Operation: Automaticf) Duty cycle: Continuousg) Transformer windings: Copper wound on CRGO laminations as per IS specificationsh) Cooling: Oil cooledi) Efficiency: Better than 98% at full loadj) Overload capacity: 15% for continuous 4 hoursk) Waveform distortions: Nill) High speed voltage correction: up to 8V to 20V per secondm) Protections: Under voltage, Over voltage and Overload with time delayn) Other features: LED indicators, Digital AC ammeter, AC voltmeter, Frequency meters, Phase Sequence meters, Single phase preventer, Stabilizer by-pass arrangement. |
| 3 | Supply, installation, testing & commissioning of 3 Phase- 10 KVA Servo-Stabilizer including oil and all allied electrical acessories with earthing.The stabiliser should have following specifications:a) Capacity:10 KVA, 3-phase unbalanced typeb) Input: (100-265) V AC P-N; (180 - 460) V AC P-Pc) Output: 415 V ± 1% - phase to phase d) Supply: 3 phase, 4 wires, 50Hze) Operation: Automaticf) Duty cycle: Continuousg) Transformer windings: Copper wound on CRGO laminations as per IS specificationsh) Cooling: Oil cooledi) Efficiency: Better than 98% at full loadj) Overload capacity: 15% for continuous 4 hoursk) Waveform distortions: Nill) High speed voltage correction: up to 8V to 20V per secondm) Protections: Under voltage, Over voltage and Overload with time delayn) Other features: LED indicators, Digital AC ammeter, AC voltmeter, Frequency meters, Phase Sequence meters, Single phase preventer, Stabilizer by-pass arrangement. |
| 4 | Supply, Installation and Testing & Commissioning of Control Panel enclosed in suitable sized CRC/weather proof Enclosure(SWG16, powder coated) with IP-Rating to prevent ingress of water and comprising of Bus bar MCCBs, contactors, relays, single phase preventers, earth fault relays, changeover switches, for lifts with following specifications with Earthing.Incomer: 1. MCCB 125 4P 01 No (30kA breaking capacity) of reputed make preferably L&T/ABB/Schneider.2. Front Operated Manual Change Over (125A) 01 No. (4P)3. MCCB 100A TPN (18kA breaking capacity) of reputed make preferably L&T/ABB/Schneider.4. 125A Aluminum 4 Pole Bus Bar –01 set 5. Digital Voltmeter with Selector Switch 6. Digital Ammeter with Selector Switch & CT’s 7. Phase Indicator Set Outgoing feeders: a) 40A Four Pole MCBs C curve (10kA breaking Capacity)- 03 No's of reputed make preferably L&T/ABB/Schneider. The job is inclusive of the cost on account of concrete foundation/footing for resting of the Control Panel. |
| 5 | Supply, Installation and Testing & Commissioning of Control Panel enclosed in suitable sized CRC/weather proof Enclosure(SWG16, powder coated) with IP-Rating to prevent ingress of water and comprising of Bus bar MCCBs, contactors, relays, single phase preventers, earth fault relays, changeover switches, for lifts with following specifications with Earthing.Incomer: 1. MCCB 100A 4P 01 No (30kA breaking capacity) of reputed make preferably L&T/ABB/Schneider.2. Front Operated Manual Change Over (100A ) 01 No. (4P)3. MCCB 80A TPN (18kA breaking capacity) of reputed make preferably L&T/ABB/Schneider.4. 100A Aluminum 4 Pole Bus Bar –01 set 5. Digital Voltmeter with Selector Switch 6. Digital Ammeter with Selector Switch & CT’s 7. Phase Indicator Set Outgoing feeders: a) 40A Four Pole MCBs C curve (10 kA breaking Capacity)- 02 No's of reputed make preferably L&T/ABB/Schneider. The job is inclusive of the cost on account of concrete foundation/footing for resting of the Control Panel. |
| 6 | Supply, Installation and Testing & Commissioning of Control Panel enclosed in suitable sized CRC/weather proof Enclosure(SWG16, powder coated) with IP-Rating to prevent ingress of water and comprising of Bus bar MCCBs, contactors, relays, single phase preventers, earth fault relays, changeover switches, for lifts with following specifications with Earthing.Incomer: 1. MCCB 80A 4P 01 No (18kA) of reputed make preferably L&T/ABB/Schneider.2. Front Operated Manual Change Over 100A ) 01 No. (4P)3. MCCB 63A TPN (18kA breaking capacity) of reputed make preferably L&T/ABB/Schneider.4. 100A Aluminum 4 Pole Bus Bar –01 set 5. Digital Voltmeter with Selector Switch 6. Digital Ammeter with Selector Switch & CT’s 7. Phase Indicator Set Outgoing feeders: a) 40A Four Pole MCBs (10 kA breaking Capacity)- 01No's of reputed make preferably L&T/ABB/Schneider. The job is inclusive of the cost on account of concrete foundation/footing for resting of the Control Panel. |
| 7 | Providing / Fitting of 3.5 core, 70 sqmm XLPE, PVC sheathed, armoured Al cable from Distribution Transformer to Servo Stabilizer with other required accessories cable glades,clamps,saddles for proper connections and fixings of suitable ratingto be laid underground as per requirement. (to be paid as per actual) |
| 8 | Providing / Fitting of 3.5 core, 50 sqmm XLPE, PVC sheathed, armoured Al cable from Servo Stabilizer to Control Panel with other required accessories cable glades,clamps,saddles for proper connections and fixings of suitable rating for proper laying/connections as per relevant standards, to be laid as per requirement. (To be Paid as per actual) |
| 9 | Providing / Fitting of 3.5 core, 35 sqmm XLPE, PVC sheathed, armoured Al cable from Servo Stabilizer to Control Panel with other required accessories cable glades,clamps,saddles for proper connections and fixings of suitable rating for proper laying/connections as per relevant standards, to be laid as per requirement. (To be Paid as per actual) |
| 10 | Providing / Fitting of 3.5 core, 25 sqmm XLPE, PVC Sheathed, Al cable from Control Panel to individual lifts with other required accessories cable glades,clamps,saddles for proper connections and fixings of suitable ratingfor proper laying/connections as per relevant standards, to be as per requirement. (To be Paid as per actual) |
| 11 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930,Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal) (To be paid as per actual). |
| 12 | Supply,installation,and wiring of IP65-rated LED bulkhead lights in the lift shaft, including secure mounting, conduit wiring, connection, testing and commissioning as per approved specifications.(to be paid as per actual) |
| 13 | Providing & Fixing of ISMB 250 as on required acting as door beams at lift landing doors. The job also includes providing and fixing of suitable MS sections for fixing of Guide Rail brackets on the MS shaft as required. Job includes applying a priming coat of approved steel primer.(if required and to be paid as per actual) |
| 14 | EarthingEarthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonryenclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required or as per OEM recommandation |
| 15 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 16 | Weather proof enclosureProviding, Construction and Fitting of 6ftX5ftX4ft weather proof Enclosure(SWG18, powder coated) for servo voltage stabilizer on concrete foundation/footing. (to be Paid if required |
| 17 | Comprehensive Annual Maintenance Contract (CAMC).Comprehensive Annual Maintenance Contract (CAMC) of above lift (including servo voltage stabilizers) which include routine, preventive & breakdown maintenance for period of ONE YEAR including repair/replacement of worn-out items with minimum downtime and warranty & guarantee of repaired/replaced items after completion of two-year DLP period. |
| 18 | Foundation for Servo Stablizer and panelProviding concrete foundation for servo stabilizer and control panel including excavation, concreting, anchor bolts fixing, leveling, curing, and making good, complete.(if Required) Please Enable Macros to View BoQ information |
