|
| 1 | Dismantling single layer mangalore pattern or similar tiles in roofing and including battens for tiles, shingles etc, of any size including tilting fillets spaced exceeding 15 cm complete all as specified and directed. |
| 2 | All as per Sl. item No. 1 above but bedded in lime or cement mortar. |
| 3 | Taking down chowkhat with shutters without taking off shutters from the frame, not exceeding 1.5 Sqm each complete all as specified and directed. |
| 4 | Taking down chowkhat with shutters without taking off shutters from the frame, exceeding 1.5 Sqm each and not exceeding 4 Sqm complete all as specified and directed. |
| 5 | Dismantling timber scantling 40 Sqcm and over in section in any position framed work complete all as specified and directed. |
| 6 | Demolition of reinforced concrete of any description (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors), beams, chajjas and similar suspended works complete all as specified and directed. |
| 7 | Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast masonry concrete articles complete all as specified and directed. |
| 8 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 10 | Taking up or down existing unserviceable GI tubes 15 mm bore of any grade and including making good the disturbed surface complete all as specified and directed. |
| 11 | Removing building materials etc, to a distance of 2 Km or under, beyond the lead included in the rates, including loading, unloading and levelling of ground complete all as specified and directed. |
| 12 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed. |
| 13 | Removing excavated soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 14 | M&L harcore broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 15 | M&L moorum / red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and directed. |
| 16 | Excavating in post holes each not exceeding 0.5 cum, getting out in soft / loose soil, ramming earth filling or broken rubble mixed with earth around in layers not exceeding 25 cm watering and removing surfaces soil to distance not exceeeding 50 m and making good surfaces complete all as specified and directed. |
| 17 | M&L PCC 1:2:4 type B2 using 40 mm graded aggregate as in foundation filling and mass concrete etc, complete all as specified and directed. |
| 18 | M&L precast cement concrete block masonry 1:3:6 type C1 using 20 mm graded stone aggregate with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified and directed. |
| 19 | M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded aggregate as sub base and including necessary formwork complete all as specified and directed. |
| 20 | M&L, PCC 1:4:8 type D2 using 40mm graded aggregate as in foundation filling and mass concrete etc., complete all as specified and directed. |
| 21 | M&L use and waste of mild steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam and similar work vertical or to batter of flat rough finished surfaces of concrete complete all as specified and directed. |
| 22 | M&L 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors and finishing surfaces even and smooth without using extra cement and including necessary formwork complete all as specified and directed. |
| 23 | S&F mild steel work in tubular trusses including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc, complete all as specified and directed. |
| 24 | S&F 5 mm thick mild steel plates (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 290 grade E-165 complete all as specified and directed. |
| 25 | S&F mild steel screw bolts (machine made) with dia of neck 11 mm to 15 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 10 cm but not exceeding 15 cm complete all as specified and directed. |
| 26 | S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps and including embeding in concrete and screwing etc, wind ties for roof including securing bolts etc, complete all as specified and directed. |
| 27 | S&F pre- painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws and EPDM washers complete all as specified and directed. |
| 28 | S&F aluminium composite panel board fixed with and including necessary frame work with screws and scaffolding complete all as specified and directed. |
| 29 | S&F 1 mm thick, UPVC eaves gutter trapezoidal type and fixing with and including suitable flat iron clamps etc, complete all as specified and directed. |
| 30 | M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified. |
| 31 | M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of primer complete all as specified and directed. |
| 32 | M&L preparation of new or previously un-treated steel and iron surfaces of any description over 10 cm in width or girth not otherwise described and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed |
| 33 | S&F 110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to walls and including necessary fittings complete all as specified and directed. |
| 34 | M&L 75 mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection etc, finishing the surfaces fair and even and including necessary formwork complete all as specified and directed. |
| 35 | M&L 100 mm thick PCC 1:2:4 type A2, using 40 mm graded aggregate as in flooring, path, hardstanding finishing the surfaces fair and even and including necessary formwork complete all as specified and directed. |
| 36 | M&L sand cushioning, watered, spread, levelled uniformly and consolidated under floors, cable protection etc, complete all as specified and directed.Note: Punned thickness will be measured for payment. |
| 37 | M&L chequered cement concrete tiles 300 x 300 mm x 25 mm thick set, jointed and pointed in neat cement slurry with grey cement and no pigments and including 20 mm thick screed bed in CM 1:6 complete all as specified and as directed . |
| 38 | M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregates as in roof kerbs or mud stops, rounded or chamfered on edge complete all as specified and directed. |
| 39 | Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation et., or for shafts, wells, cesspits, manholes, pier holes, cables pipe lines etc, not exceeding 10 sqm on plan and getting out in hard / dense soil complete all as specified and directed. |
| 40 | M&L PCC 1:2:4 type B0 using 12.5 mm aggregate as in coping and including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 41 | M&L PCC 1:2:4 type B1 using 20 mm graded aggregate as in surface channels and drains complete all as specified and directed. |
| 42 | Extra for forming fair finished drain or channels 45 cm inner girth in cement concrete, using extra cement and including forms, moulds, mitred / stopped ends etc, complete all as specified and directed. |
| 43 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soils complete all as specified and directed. |
| 44 | M&L PCC 1:3:6 type C2 using 40 mm graded aggregate as in foundation, filling and mass concrete etc, complete all as specified and directed. |
| 45 | M&L RCC (nominal mix) 1:2:4, type B1, using 20 mm graded aggregate, in foundation, footings, foundation beams; plinth beams; bases for columns and mass concrete complete all as specified and directed. |
| 46 | M&L mild steel TMT bars 10 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 47 | M&L mild steel round bars 10 mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips Fe 410W Gde E-250, quality-A or Fe 290 Gde - E-165 complete all specified and directed. |
| 48 | S&F mild steel screw bolts (machine made) with dia of neck 5 mm to 10 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5 cm but not exceeding 10 cm complete all as specified and directed. |
| 49 | Supply only mild steel galvanised chain link fencing of any size or type complete all as specified and directed. |
| 50 | Fixing only chain link fencing and including line wires, any mesh, size & type to any type of standards, rails, straining bolts etc, including provision of binding wire complete all as specified and directed. |
| 51 | S&F galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc, complete all as specified and directed.Note: Each line wire shall be measured. |
| 52 | M&L PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed. |
| 53 | M&L 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 54 | M&L PCC 1:3:6 type C-0, using 12.5 mm graded crushed stone aggregate as in copings and bed blocks, bed plates and the like including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 55 | S&F framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed. |
| 56 | All as per Sl.item No. 56 above but portions framed & hung as gates, including pintle hinges, stops, hand made sliding bolts, etc, |
| 57 | M&L, Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed. |
| 58 | M&L preparation of new steel surfaces of any description, not exceeding 10 cm in width or girth when unconnected with other painting or when painted in a different tint and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 59 | Supply, installing, testing and commissioning organic waste composter machine fully automatic upto 600 - 620 kg per day with suitable motor for shredder and mixing chamber with blower arrangement approx. 10 KW heating system ceramic coil based for the following complete all as specified and directed :-Control system : PLC with touch screen HMIProcessing time : 24 HoursMain motor capacity : 3 HPShredder motor capacity : 2 HPBlower motor capacity : 0.5 HPTank volume : 2460 LitresPower consumption per day : 80-90 unitsTotal load : 14.1 Kw (19 HP)Dimensions (L x W x H) in mm : 3300 x 1650 x 2400 mmComposting method : Mechanical shredding and in vessel composting using thermophilic microorganismsTreatable items : All bio degradable organic waste, garden waste, small bones. Make: M/s Aakaar Green (Model :- Green Guru composter) or its equivalent approved make. Please Enable Macros to View BoQ information |
| 60 | Supply, installing, testing and commissioning organic waste composter machine fully automatic upto 600 - 620 kg per day with suitable motor for shredder and mixing chamber with blower arrangement approx. 10 KW heating system ceramic coil based for the following complete all as specified and directed :-Control system : PLC with touch screen HMIProcessing time : 24 HoursMain motor capacity : 3 HPShredder motor capacity : 2 HPBlower motor capacity : 0.5 HPTank volume : 2460 LitresPower consumption per day : 80-90 unitsTotal load : 14.1 Kw (19 HP)Dimensions (L x W x H) in mm : 3300 x 1650 x 2400 mmComposting method : Mechanical shredding and in vessel composting using thermophilic microorganismsTreatable items : All bio degradable organic waste, garden waste, small bones. Make: M/s Aakaar Green (Model :- Green Guru composter) or its equivalent approved make. Please Enable Macros to View BoQ information |
