|
| 1 | Dismantling boarding,etc any description, fixed in any position with nails etc inluding iron/SS mongeries if any complete all as specified and directed. |
| 2 | Demolition of Concrete of any description and in any position not otherwise specifically provided for floor(other than above ground level),sunken floor etc all as diercted. |
| 3 | Demolition of cement concrete (reinforced ) (below or above ground level) and removing debris off the site complete all as specified and as directed. |
| 4 | Demolition for brickwork or stone masonry laid with cement mortar or cement lime mortar |
| 5 | Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed. |
| 6 | Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each complete all as specified and directed. |
| 7 | Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm and not exceeding 4 Sqm each, complete all as specified and directed. |
| 8 | Taking down steel tubing and connections of 15 mm bore including cleaning for refixing or removal to store complete all as specified and as directed. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 10 | Dismantling Stone slabs and tiles of any description or thickness in floors,sill,and platform etc complete all as directed. |
| 11 | M&L PCC 1:4:8 type D2 with 40mm graded stone aggregate as in foundation,filling and mass concrete as in sunken floor/toilet floor /kitchen floor concrete finished the surfaces even and fair to receive top layer all as specified and as directed. |
| 12 | M&L Providing 25mm thick cement concrete type B0, 1:2:4 using 12.5 mm graded stone aggregate .as in floors for levelling course including finish the surface even and rough to receive the top finish complete all as directed. |
| 13 | M&L for non skid ceramic tiles7 to 8 mm thick (square/rectangle) area of each tile exc 0.06sqm but not exc 0.11 sqm, in floors and scantling etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified |
| 14 | M&L for coloured glazed ceramic tiles of size 300x600x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting set in redering 10mm thick CM 1:3 complete all as specified |
| 15 | M&L for Reinforced Cement Concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, for kitchen platform,shelve etc complete as specified and as directed. |
| 16 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick as in flat rough finished surface complete as specified and as directed. |
| 17 | S&F TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete as specified and as directed. |
| 18 | Material and labour for Granite work with 20mm thick machine cut, Jet Black granite slab in single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:3, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone as in cooking platforms, microwave platform, WHB counter top in steps, jambs, pillars, window-cills, etc, including cutting, polishing and rounding to edges of stone slabs etc., complete all as specified and as directed. |
| 19 | M&L for Pre-cast cement concrete block masonry with solid blocks Type C1 1:3:6 (20 mm gradedaggregate) exc. 10 cm in width and setting in mortar 1:6,complete all as specified and directed. |
| 20 | M&L for providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C-1 (1:3:6) using 20mm graded stone aggregate set in cement mortar(1:4), complete, in walls ,partion,platform support etc |
| 21 | Supply and fix 18mm thick High Density High Moisture Resistant (HDHMR) Board/ HDWR Board, both side laminated of approved colour as in shutters, back board, vertical support and horizontal shelves of kitchen/bedroom cupboards fixed with screw to timber framed work etc.,complete all as specified and as directed.Note: All exposed edges/surfaces to be finished with same laminated sheet to match with the exisiting surfaces and nothing will be paid extra. |
| 22 | S&F 15 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed. |
| 23 | Refixing of old GI steel tubes and connections after cleaning of 15 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed. |
| 24 | M&L for 10mm thick rendering plaster on fair face of brick-work or concrete surface incl finish the surface even and smooth without using extra cement in CM 1:6 complete all as specified and as directed . |
| 25 | Material and labour for rendering 5mm thick in Cement Mortar 1:3 on concrete surfaces of ceiling chajja etc , finished even and smooth without using extra cement complete all as specified and as directed. |
| 26 | M&L for preparation of new surfaces of wall and applying with white putty of average thickness 1.5mm and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distermper over a coat of chalk white primer and all as specified and as directed |
| 27 | M&L for complete removal of existing treatment on surfaces of wall and applying with white putty of average thickness 1.5mm and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distermper over a coat of primer and all as specified and as directed. |
| 28 | M&L for complete removal of existing treatment on surfaces of ceiling and applying two coats of white wash complete all as specified and as directed. |
| 29 | M& L for applying two coats of white wash on ceiling including preparation of newly plastered surfaces of ceiling complete all as specified and as directed. |
| 30 | Supply and fix stainless steel telescopic ball bearing channel, zinc plated finish for drawer including necessary fittings up to length of 600mm fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH |
| 31 | Supply and fix Stainless steel soft close hinge with 35mm cup dia, full overlay, 110 degree opening suitable for 18mm thick shutters complete all as specified and as directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH |
| 32 | Supply and fix Stainless steel handle of size 150mm for kitchen/bedroom cupboards fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH |
| 33 | Supply and fix Magnetic closer of suitable size for kitchen/bedroom cupboards fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH |
| 34 | Supply and fix 50 mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/sqcm in any length with rubber ring joint complete all as specified and as directed. |
| 35 | S&F stainless steel kitchen baskets(SS-304) of size 544mm x505mmx200mm complete all as specified and directed.Make :EBCO cat No: RA-BCCS1-21-20-8 or equivalent in HETTICH/ KAFF/ GODREJ |
| 36 | S&F stainless steel kitchen baskets(SS-304) of size 544mm x505mmx100mm complete all as specified and directed.Make :EBCO cat No: RA-BCCS1-21-20-4-CT or equivalent in HETTICH / KAFF/GODREJ |
| 37 | S&F stainless steel kitchen baskets(SS-304) of size 530mm x505mmx200mm complete all as specified and directed.Make :EBCO cat No: RA-21-20-8 or equivalent in HETTICH/KAFF/GODREJ |
| 38 | S&F stainless steel kitchen baskets(SS-304) of size 530mm x505mmx150mm complete all as specified and directed.Make :EBCO cat No: RA-21-20-6-PL or equivalent in HETTICH/KAFF/GODREJ |
| 39 | S & F in repair Single lever sink mixer with swinging spout, wall mounted model with connecting legs and wall flanges complete all as spd and directed. Make- Cat No G3335A1 of Parryware/Cat No F320027 of Hindware/Cat No 7855 of Prayag or equivalent all as specified and directed.. |
| 40 | S&F in repairs stainless steel Double bowl kitchen sink undermount -flat edge gloss finish (40\\"Lx20\\"Wx8 \\"D) fitted with cement mortar/chemical adesive on granite/marble back platform etc including necessary fittings like waste coupling/wastepipe etc all as specified and as directed. Make :Parryware cat No :C855981 or equivelent |
| 41 | UPVC windows : Supply and Fix factory made UPVC white sliding windows with glazing all as per manufacturer's direction and following specifications :- (i) Window panel shall be 2.5 track frame with upvc profile section of size 95mmx 54mm having outer wall thickness of 2mm(+/- 0.3mm ) with sliding pattern with glazed and mesh shutter.(ii) window glass shutter for (front panel )shall be made of 66mmx 42.5mm having outer wall thickness of 2.0mm(+/- 0.3mm) .(iii) Window mesh shutter shall be made of 52mm x 22mm.Gauge shall be suiable wire gauge SS304 coated/fiber black mesh. (iv) All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required.(v) All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints.All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make nthe finished products free from all sharp edges & burrs.(vi) The lock shall be single point topuch lock.All hardware like wheel,lock should be screwed .System shall be provided with suitable upVC beading size of 25mm x15.5mm for glazing of size 4mm/5mm pinhead /plain glass as directed by the Engineer In charge. (vii) The profiles shall be cut to lenth and welded 45 degrees .(iii) The complete window shall be fixed into the prefinished opened placec by drilling & fixing thorugh the outer frame using high quality fasteners & silicon sealent is applied to fill up the gap between wall & window frame for leak proof installation and completion. Note: The entire fixing will be done as per manufactures instructions and specification and as directed by Engg in charge. (II) The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose. |
| 42 | Supply and fix UPVC panel door shutters with frames with approved make and section and colour with all necessary fixtures like hinges, handles, bolts etc all as specified and directed.the detailed specification as follows.(i) Door frame shall be upvc profile sedction of sizesize of 60mm x 60mm wall thickness of 2mm(+/- 0.3mm ) with openable pattern.)(ii) Door shutter with sash made of 80mm x60mm and panel shall be 10 to15mm thick(+/- 0.3mm ) .All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required.(iii)All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanicasl joints.All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make nthe finished products free from all sharp edges & burrs.(vi)The profiles shall be cut to lenth and welded 45 degrees |
| 43 | Supply and fix UPVC Mesh door shutters with frames with approved make and section and colour with all necessary fixtures like hinges, handles, bolts etc all as specified and directed.the detailed specification as follows.(i) Door frame shall be upvc profile section of size of 60mm x60mm wall thickness of 2mm(+/- 0.3mm ) with openable pattern.(ii) Door shutter with sash made of 80mm x60mm) .All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required.(iii)All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints.All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make the finished products free from all sharp edges & burrs.(vi)The profiles shall be cut to lenth and welded 45 degrees(vii) Gauge shall be suiable wire gauge SS304 coated/fiber black mesh. |
| 44 | S&F in repair bib cock long body with wall flange .Make: Cat No G1405A1 of Parryware/ F730011 of Hindware / CON 107 KN of Jaquar or equivalent all as specified and directed. |
| 45 | S&F two piece type stainless steel cockroach tap square or round 100 mm size complete all as specified and as directed. |
| 46 | S&F 75mm dia PVC floor multi trap with and grating of size 100 x 100 mm complete all as specified and as directed. |
| 47 | S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in floor/trenches complete all as specified and as directed. |
| 48 | S & F PVC (SWR) bends any radious 75mm bore provided with acess door complete all as specified and as directed. |
| 49 | Supply and fix in repairs, stainless steel plate racks made of stanless steel 0.80mm thick sheet standard size 24'x36x10\\" and design as approved by GE, complete all as specified and as directed. Make: Nirali/Parryware as approved by GE. |
| 50 | Demolition of cement concrete (unreinforced ) (below or above ground level) and removing debris off the site complete all as spcified and as directed. |
| 51 | M&L 75mm thick Plain Cement Concrete type C-1, 1:3:6 (20mm graded stone aggregate) as in sub base of floor etc. finished even & rough to receive the top finish complete as specified and as directed. |
| 52 | Material and labour for Granite of any type tiles 20 mm thick over 20mm thick cement screed in cement mortar 1:4, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in flooring complete all as specified and as directed. |
| 53 | S&F in repairs for plain transparant Polycorbonate sheet 4 mm fixed to steel frame with all necessary fitting incl dismantling of old roof sheets complete all as specified and as directed |
| 54 | M & L for mild steel work as in tubular roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, square tube etc sections) including distance pieces, cleats etc. Fe 410-W (Gde-E- 250) quality- A complete all as specified and as directed. |
| 55 | M/L for preparing new surface of steel and appling two coats of synthetic enamel paint over a coat of primer red oxide complete all as specified and as directed. |
| 56 | M/L preparing old surface of steel and appling one coat of synthetic enamel paint complete all as specified and as directed |
| 57 | M&L for hardcore of gauge n.exc 63 mm deposited, spread & levelled in layers n. exc 15 cm thick, watered & rammed to a true surface with broken stone or boulders complete as specified and as directed. |
| 58 | M&L for 75mm thick Plain Cement Concrete type C-1, 1:3:6 (20mm graded stone aggregate) as in plinth protection finished even & smooth finish complete as specified and as directed. |
| 59 | S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed. |
| 60 | M&L for complete removal of existing treatment on surfaces of wall and applying two coats of Oil bound distermper over a coat of alkali resistant primer by approved applicator of the manufacturer of the paint and all as specified and as approved |
| 61 | Complete removal of existing treatment on external walls by wire brushing, crack filling & Bio-wash to fight microbial growth and applying, one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint complete all as per manufacturer instruction as directed: NOTE: The painting work to be executed by authorised applicator of the manufacturer.Make :-APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top guard of Nerolac |
| 62 | S&F 75 mm dia stainless steel (square/circular) of grade 304 in railing including necessary fabrication, drilling, grinding,polishing etc and embeded in to PCC 1:3:6 including excavation in post holes, return filling and levelling and removal of soil etc complete all as directed |
| 63 | S&F in repairs for SS Chairs 3 seater silver colour fixing into floor as per specified |
| 64 | M&L for prepration of old random rubble masonry surface including removing bushes, shrubs and vegitation if any from block/stone masonery retaining wall at any height up to 8 m and making surface clean by removing waste and filling the damage joints with cement morter 1:6 and applying two coats of cement base paint over one coat of chalk white primer etc complete sll as specified and as directed |
| 65 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.. complete all as specified and directed. Please Enable Macros to View BoQ information |
| 66 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.. complete all as specified and directed. Please Enable Macros to View BoQ information |
