|
| 1 | Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment orstacking as directed. |
| 2 | Transportation of Excavation Stuff up to 4km |
| 3 | Supplying hard murum/ kankar at the road site, including conveying and stackingcomplete. |
| 4 | Spreading hard murum/ soft murrum/ gravel or kankar for side width complete |
| 5 | Compacting the hard murum side widths including laying in layers on each side withvibratory roller including artificial watering etc. complete. |
| 6 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means - Grading II (Using Screening Type B (11.2 mm) Aggregate) |
| 7 | Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 8 | Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stone in cement mortar 1:3 in basement with patent water proofing compound added to it at rate of 1Kilogramper bag of cement including bailing out water manually,scaffolding racking out joints when plastering is to be done and watering etc. complete. |
| 9 | Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete. |
| 10 | Providing first class Brick masonry with conventional / IS. type bricks in cement mortar 1:4 including scaffolding, racking out joints pointing in C.M 1:3 and watering etc. in pillars of curved shapes, as shown on the drawing or as directed etc. complete. |
| 11 | Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for plain or molded sills, cornice, jambs, block in course, or architraves of required size and shapes including steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided,finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer etc. complete, With fine aggregate (Crushed sand VSI Grade) |
| 12 | Providing and fixing heavy duty inter locking concrete Coloured paving blocks of60 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints andcleaning etc. complete |
| 13 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 14 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. |
| 15 | Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coatsof approved shade Weight of gate 35 Kilogram/Smt. |
| 16 | Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 17 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 18 | Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 19 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. |
| 20 | Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: ForItem One Number 15 to 18 prior approval of Superintending Engineer will be necessary |
| 21 | Excavation for Planting of Lawn/ Shrubs/ Creeper/ Climbers/Ground Cover on Soft Surface – Digging of Soft surface up to 30 Cm. Depth and removal of excavated material from site by contractor. |
| 22 | Preperation of ground for planting of lawn/shrubs/ ground cover/ creeper/ climbers - Suply and Spreading of Red Hill Earth and Cow Dung Mannure in 2:1 Proportion up to 30 cm. Depth ( excluding cost of Lawn/shrubs/ ground cover/ creeper/ climbers .) |
| 23 | Planting of lawn- Laying of Carpet lawn ( zoysia / American / mexican/ korean carpet ) |
| 24 | Providing, hoisting and fixing at all level precast or reinforced cement concrete gazebo with all elements like roofing, string courses, bands, copings, columns, pillars beams, plinth beams, railings, benches, flooring, foundations including architectural design, moulding, arches, shapes, and applying proper texture and paining coats to suit a particular astheticelement (trunk of trees, shapes of animals, birds, timber benching, any element or structure representing culture or tradition) the cost of requiredcentering, shuttering and reinforcement, of M25 grade and fibrous material, etc complete as per the instructions of Architect or Engineer-incharge. |
| 25 | Ss Dust Bin Product area:0.76Sqm, Capacity in ltrs: 42.0 ltrs, Product height:0.92m |
| 26 | Sleek Bench (Refer sketch 20) Product area: 1.2 x 0.6 mts, Capacity in nos: 3 nos, Product height:0.5m |
| 27 | Trunk Bin (Refer sketch 6) Product area:0.38Sqm, Capacity in ltrs: 72.0 ltrs, Product height:0.69m |
| 28 | Puppy Bin (Refer sketch 7) Product area:0.38Sqm, Capacity in ltrs: 68.0 ltrs, Product height:0.69m |
| 29 | Bird Bin (Refer sketch 8) Product area:0.38Sqm, Capacity in ltrs: 68.0 ltrs, Product height:0.69m |
| 30 | Brinjal Dust Bin (Refer sketch 12) Product area:0.61Sqm, Capacity in ltrs: 64.0 ltrs, Product height:0.95m |
| 31 | MPPS - 2.1 M Height - Ground Area 13.4 x 7.3m, Safe Area 16x10m, 2 stations at 2.1 m height,Providing and Fixing as per design and drawing directed by Engineer in charge with 2 years warrantyProduct Name MPPS 2.1 mtr Height - Hexagonal Deck Ht. 2.1 MTR The platform shall be made up of Fiber Reinforced Plastic (FRP) 6 to 8 mm thickness with anti skid surface. Platform Diameter 2 Mtr.The platform 6 Nos. support with 80 mm GI pipe. Top railing made up of 20mm G.I. pipes, BraisingHexagonal frame shall be made from 40 x 40 x 5 mm thickness MS angle, Total area required for Hexagonal deck 2 x 2 Mtr. Platform support pipe and Braising frame shall be powder coated. Platforminside 40 x 40 x 5 mm thickness MS angle Frame. S.S. (Non Rusting) Nut Bolt 12 mm & Nylon LockNut with Nylon Cap made with 66 nylon Material. Powder Coating 60 Micron with PP Powder,Hexagonal Roof The Hexagonal canopy is made up of Fiberglass Reinforced Plastic 3mm thick SquareDeck Ht 2.1 MTR The platform shall be made up of Fiber Reinforced Plastic (FRP) 6 to 8 mm thicknesswith anti skid surface. Platform of each side should be equal in length 1.0m x 1.0m. The platform 4Nos. support with 80 mm GI pipe. Top railing made up of 20mm G.I. pipes, Braising Square frame shallbe made from 40 x 40 x 5 mm thickness MS angle, Total area required for Square deck 1.0 x 1.0 Mtr.Platform support pipe and Braising frame shall be powder Sated. Platform inside 40 x 40 x 5 mmthickness MS angle Frame. S.S. (Non Rusting) Nut Bolt 12 mm & Nylon Lock Nut with Nylon Capmade with 66 nylon Material. Powder Coating 60 Micron with PP Powder. ROTO Square Roof FRPStep Ladder Ht 2.1 MTR The attractive Ladder chute shall be made from Fiber Reinforced Plastic(FRP) / Low Linear Density Poly Ethylene (LLDPE) of 7 to 8mm Thickness. The chute has Non Skidgel coat finished. 5.5. (Non Rusting) Nut Bolt 10 mm & Nylon Lock Nut with Nylon Cap made with 66nylon Material Powder Coating 60 Micron with PP Powder Roller Slide Ht 2.1 Mtr The most attractive of its kind, the chute of this slide shall consist of plastic rollers. The rollers shall be made up of HighDensity Polyethylene Plastic (HDPE) with UV stabilized. Roller's rod shall be made from 12 mm diabright rod and nylon bush fitted in Rollers for smooth rotation. The main frame shall be made up of M.Sangle 50 x 50 x 5 and MS flat 50 X 3. The handrail shall be made in 25 mm NB GI pipe. The triangular steps provided shall be made out of 16 SWG GI sheet for firm grip and safety. H' support shall bemade from 25 mm NB GI pipe and 25 x 10 MS flat All pipes, angle and flat shall be powder coated toavoid rusting. S.S. (Non Rusting) Nut Bolt 10 mm/8 mm & Nylon Lock Nut with Nylon Cap made with66 nylon Material. Powder Coating 60 Micron with PP Powder. FRP Deluxe Wave Slide Ht 2.1 Mtr TheDeluxe Wave slide shall be made of Fiber Reinforced Plastic (FRP) of 8 mm thickness both side gelcoat finished. The Slide shape should be made of proper degree for safety sliding. Centre Support of slide 25mm G.I. Pipe, End support shall be made from 25 mm GI pipe. 3 S.S. (Non Rusting) Nut Bolt10 mm/ 8 mm & Nylon Lock Nut with Nylon Cap made with 66 nylon Material. Powder Coating 60Micron with PP Powder. Rock Scrambler Ht.2.1 Mtr Mtr Rock climber platform shall be made up of 5mm to 6 thick FRP (Fiber Reinforced Plastic) / LLDPE (Low linear Density Poly Ethylene) / ROTO.Rocks shall be bolted on same platform and ground support for the platform 25 mm NB GI pipe 50 x 10MS flat shall be used. All pipes, flat shall be powder coated to avoid rusting. S.S. (Non Rusting) NutBolt 10mm & Nylons Lock Nut with Nylon Cap made with 66 nylon Material. Powder Coating 60 Micronwith PP Powder. Loop Scrambler The frame is fabricated out of 80mm and 25mm GI pipes, top bar 50mm GI Pipes .There are loops Fabricated out of 20mm GI Pipe & Supported by hooks made up fromMS Flat 50 X 10mm. All Pipe & frame shall be powder coated or PU painted. The ladder used shall bedesigned to the side support pipe itself attached with Nylon Clamp. S.S. (Non Rusting) Nut Bolt 10 mm& Nylon Lock Nut with Nylon Cap made with 66 nylon Material. Powder Coating 60 Micron with PPPowder. FRP Tube Slide Ht 2.1 Mtr Tube slide shall be made up 4 mm thick FRP (Fiber ReinforcedPlastic)/LLDPE (Low linear Density Poly Ethylene) having smooth finishing. Weight of FRP mini Tubeis 89 KG. Cross section slide shall be 750 mm Diameter. It shall have a transparent cover so that lightcan pass through it. Slide shall be supported with 'T' support made up 80 mm NB GI pipe speciallydesigned MS Flange of 10 mm thick shall be used for fixing T support with slide. All pipes and Flangeshall be powder coated to avoid rusting. S.S. (Non Rusting) Nut Bolt 10 mm/8 mm & Nylon Lock Nutwith Nylon Cap made with 66 nylon Material. Powder Coating 60 Micron with PP Powder. Double ArchSwing The arch shaped side frame of the swing are made up of 80 mm GI pipe and top pipe is madeup of 50 mm Gl pipe. Supporting top bar of the swing is fitted with special design Nylon clampsassembly. It gives noiseless and Smooth movement to the swing, Plastosol coated short link chain of 6mm dia. Seat used is rubber with Non Skid surface with nylon lining pattern. Triangular hook aremolded in belt in such a way that it would not project from the top surface of the belt Seats. All GIStructure is Powder coated/PU Painted. S.S. (Non Rusting) Nut Bolt 12 mm & Nylon Lock Nut withNylon Cap made with 66 nylon Material. Powder Coating 60 Micron with PP Powder. SuspensionBridge Lt.3.0 Mtr The Swinging Bridge shall be made of 10mm Thick tested chain link & FRP/LLDPESteps, Steps made of 25 x 25 x 5 MS angle with 5 mm FRP/LLDPE. Top Bar 40mm GI Pipe. Therailing shall be made from 25mm & 20mm GI Pipes, All Pipe & frame shall be powder coated or PUpainted. The railing shall be made from FRP (Fiber Reinforced Plastic) / LLDPE (Low linear DensityPoly Ethylene) and shall be supported by 20 mm NB GI pipe and clamped with 80 MM NB and 80(mm) x 20(mm) nylon clamp made with 66 nylon Material. U nut 12 mm 4 Nos. S.S. (Non Rusting) NutBolt 10 mm & Nylon Lock Nut with Nylon Cap made with 66 nylon Material. Powder Coating 60 Micronwith PP Powder. ROTO Railing The railing shall be made from FRP (Fiber Reinforced Plastic)/LLDPE(Low linear Density Poly Ethylene) and shall be supported by 20 mm NB GI pipe and clamped with 80mm NB and 80 (mm) x 20(mm) nylon clamp. All pipes shall be powder coated to avoid rusting. S.S.(Non Rusting) Nut Bolt 10 mm & Nylon Lock Nut with Nylon Cap made with 66 nylon Material. Powder Coating 60 Micron with PP Powder. Rubber Net Scrambler Ht.2.1 Mtr The Net Scrambler made for challenge climbing shall be made up of Natural Rubber molded With 6mm tested chain link, 400mmLength. & 30mm Diameter molded rubber joint each other with MS Clamp. Clamp shall be powder coated. S.S. (Non Rusting) Nut Bolt 10 mm & Nylon Lock Nut with Nylon Cap made with 66 nylonMaterial. Powder Coating 60 Micron with PP Powder. |
| 32 | Leg Press Providing and fixing Leg Press made from “B” Class G.I. pipe. The center pipeis of 100mm NB made from “C” Class G.I. pipe, and the bottom support of M.S. Round plateof 250 mm diameter & 10mm thickness is welded at bottom. The remaining outer frame is of 40mm NB made from “C” class G.I. pipe. The foundation used for fixing is consist of threeequal items i.e. 80mm NB made from “C” class G.I. pipe, M.S. Round plate of 250mm dia &10mm thickness, 25 mm X 25 mm X 3mm M.S.angle. To join the centre pipe & outer frameseamless pipe of 130 mm dia & 3mm thickness is used. The seats are fitted on the outer frame is made up of FRP material of size 330 mm X 330 mm of thickness 3 mm & M.S.Plate of thickness 5mm and Size 250 mm X 200 mm is used to support it. The footrests ismade from FRP/C.I./Aluminum casting material, its sizes are 130 mm X 300 mm & 5 mmthickness. The frame of footrests consists of 25 NB made from “C” class G.I. pipe. Closingcaps made from top quality FRP material which is of 2 mm thickness. The inner bushes aremade from seamless pipe, its diameter is60mm& 8mm thickness. The pins used in aremade up of 25 mm diameter hardened bright bar. The bearings used are of “6205”permanent lubricated sealed bearing of reputed make like SKF, FAG. The handles used areof Rubber grip. The Nut Bolts used for assembly are made from S.S. material. The bushes(stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mmdiameter. The serclip used for assembly are of 25mmdiameter. foundation pipes areembedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is doneby attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best qualitybrand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipebeen closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, , transport, etc complete all. |
| 33 | Air Walker DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm(Height).SAFE AREA: - 2.0 M x 1.8 M Air Walker Equipment made from “B” class G.I. Pipe of different NB. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which isbend at the radius of 250mm. The bottom support of M.S. round plate of Ø250 mm & 10mmthick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link issupported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” ClassG.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipesupported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCsquare pipes of 3mm thickness. Closing Caps are made up of high quality Fiber reinforcedPlastic material. Pins used of Diameter 25mm are made up from bright material. A24 circlipsare used for assembly. The bearings used are “6205” permanent lubricated sealed bearingof repute brand likw SKF, FAG. High tensile steel galvanized nuts & bolts are used for assembly. The footrests are made from casted Aluminum material, having sizes 130mm X310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To buildstructure bushes are used which are made from M.S.seamless pipe of 60mm O.D. and 5mmthickness as well as 60mm diameter solid bar bush is used. Bolt M8 X 16 mm and Nylocknut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pinsfrom rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied beforetop coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. |
| 34 | Single Chest Press DIMENSIONS:- 9000mm (L) x 650mm (W) x 2150mm. (H).SAFEAREA :- 2.0 M X 1.7 M. Chestpress equipment madeup of“B”ClassG.I.pipe of differentNB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100NBmadeup of“B”Class G.I. pipe. The bottom welded with supportof M.S.round plate of Ø250mm &10mm thickness.The connecting pipes are made up from 25NB “B”classG.I.pipe. The handle frame is made up from 25NB & 32NB “B”class G.I.pipe. To buildstructure bushes are used which are made from MS.seamless pipe of 60mm O.D. and 5mmthickness as well as 60mm diameter solid bar bush isused. The foundation used for fixing isa structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. roundplate of Ø250 mm&10mmthick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Foundation cover Closing Cap is madefrom HDPE / LLDPE Material.The seats and Back rests are fitted onthe outer frames are made up of M.S. Sheet of size 330mmX 300mm X 2mm thickness anddeep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharpedges.Closing Caps are made up of high quality HDPE / LLDPE material. Pins used of Diameter 25mm and 17mm are made up from bright material. The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG.High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24mm & A16mm. The foundation pipes are embedded in C.C. stockof size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed byGI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material,, transport, etc complete all. |
| 35 | Cross Trainer DIMENSIONS:-1320mm (Length)x 600mm (Width) x 1750mm. (Height).SAFEAREA:-1.77x1.2Mtr. Crosstrainer equipment madefrom“B” ClassG.I.Pipe of differentNB. NB stands for Nominal Bore Sizes i.e. Internal Dia. of pipe in millimeters. Make of G IPipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame Pipesareof80NB“B”ClassG.I.Pipe with single bend pipe with 250mm radius. The bottom support of M.S.round plate of Ø250mm &10mm thick. The Handle Frame is made up of 25NB “B” Class G.I.Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supportedwith 25mm X 25mm M.S.angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. To build structure bushes are used which are made from M.S. seamlesspipe of 60mm OD. With 5 mm thickness. The foot rests are made from HDPE / LLDPEmaterial of size 130mm X 310mm X 5mm thickness and mounted on M.S.Plate of Size130mm x 310mm x 3mm thick Closing Caps are made up of highquality HDPE / LLDPEPlastic material. Pins used of Diameter 35mm, 25mm, and 17mm are made up from brightmaterial. The Bearings used are of “6007zz” “6205zz” and “6203zz” permanent lubricatedsealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts andbolts are used for assembly. A16 , A 24 mm circlips are usedforassembly. Bolt M8X16 mmand NY lock nut of M8 made of SS are used on nylon cap mounted on pins to protectbearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color sprayingafter proper surface treatment, Shot blasting and initial coat of yellow primer surface isapplied before top coat. The top coat is done using the best quality brand paint or dulypowder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI /HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, ,transport, etc complete all. Please Enable Macros to View BoQ information |
