|
| 1 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed. |
| 3 | S&F 2nd class hardwood plain solid, straight chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified in and directed. |
| 4 | S& F 35 mm thick flush shutters (factory made) solid core construction, with block board core and plywood face pannel, both face is covered with decorative face veneer with lipping/frame to match both sides. Flush shutters shall have teak wood edging including melamine polishes of complete shutter complete all as specified. |
| 5 | S& F 35 mm thick flush shutters (factory made) solid core construction, with block board core and plywood face pannel, commercial type on both sides. Flush shutters shall have teak wood edging complete all as specified. |
| 6 | S&F 35mm thick 2nd class Hard wood rail & style (factory made) plain, framed, panelled shutter (two panel) with lock rail & panel of 12mm veneered particle board with commercial veneering on both sides. The size of rail & style as per IS :1003 (Part I), Kilan seasoned & chemicals pressure treated, complete all as specified. |
| 7 | S&F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as directed. |
| 8 | S&F 18/19mm thick LEAD FRE PVC celuka ply of single side rigid laminated of approved colour and other side plain white colour fixed with screws or including L-Bihari hinges with as required (min two in every shutters) and cement adhesive to make kitchen/bedroom cabinet sides top and bottom and shelves inside the cabinet complete all as per manufactures specification complete all as specifiied and as directed by Engr-in-Charge |
| 9 | Dismantling boarding any drscription, fixed in any position with nails complete all as specified and directed. |
| 10 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 11 | S&F 1mm thick wood grain printed PVC sheet fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing at site as per specification and as directed. |
| 12 | S&F 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work all as specfied and directed |
| 13 | S&F 18/19 mm Block board, grade 2 quality, interior grade, commercial type decorative type, one face to timber frame work all as specfied and directed |
| 14 | S&F 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required rectangle/Square all as specified and as directed. |
| 15 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where eve required) and fitting the same with necessar stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 16 | M&L for repairing of aluminium window, door of any description ( sliding /side hanging type) and replacing minor fitting such as lock, hinges, bottom roller 'H' type, glass, board, wire mesh etc. refixing the shutter in the same opening including necessary minor fitting complete all as specified and as directed. |
| 17 | M & L for easing adjusting of aluminum window both shutter and refitting of shutter section with screw including replacement of unserviceable locking arrengment ,stay hook and nessessary neoprene beading comp all as spd and as directed |
| 18 | M & L for easing adjusting of aluminum doors either or double both and refitting of shutter section with screw including replacement of unserviceable locking arrengment ,stay hook and nessessary neoprene beading comp all as spd and as directed |
| 19 | M & L for easing adjusting of pannelled/skelton shutter fixed with spring type hinges in press steel shutters either or double both and refitting of shutter section with screw including replacement of unserviceable tower bolt/handle essessary neoprene beading comp all as spd and as directed |
| 20 | M&L for aluminium sections for side hung/sliding window/doors and partitions etc. with suitable sections for frame and shutter fixed with dash through holder fastener with length not less than 75mm to walls/floors including locking arrangement and rubber gusket necessary channel, neoprene beading, clips, fixing screws, nuts etc. complete all as directed. |
| 21 | S & F Anodised aluminium window and ventilator shutters,side hung/sliding type with styles,rails,sash bar,sliding frame etc all are made from aluminum anodise section weighing 0.55 kgs/m including necessary joining cleats ,glazing clips, rubber packing with locking system anodised aluminium snap beading screws complete all as specified and directed. |
| 22 | S & F Anodised aluminium window and ventilator shutters,fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified system anodised aluminium snap beading screws complete all as specified and directed. |
| 23 | S&F Anodised aluminium door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 24 | Providing and fixing factory made uPVC white colour Sliding window (area n exceeding 2sqm each) Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 25 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 26 | S&F Anodised aluminium grill, 10mm thick, diamond shape with apareture 75mm fixed to windows including u type frame and nut complete all as specified and as directed. |
| 27 | Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads all as directed. |
| 28 | S&F coloured sheet glass 5.50 mm thick ordinary quality and glazing with oil putty or glazing pins / spring clip in square, rectangle exc 0.5 Sqm in each pan all as specified and as directed. |
| 29 | M&L 5.5 mm thk frosted Sheet glass, ordinary quality and glazing with brass screws in square exc 0.5 sq. m in each pane complete all as specified as directed |
| 30 | S&F sheet glass 4.0 mm thick ordinary quality and glazing with oil putty suare, rectangle n.exc 0.5 Sqm in each pan all as specified and as directed. |
| 31 | M&L for Rim latch with two levers, of aluminium alloy body (75mm size) stove enamelled finish; with brass knob or lever handle and fixed complete all as specified as directed |
| 32 | S&F for Mortice lock, vertical type, size 100 mm 2 lever complete all as specified as directed |
| 33 | S&F for Mortice lock, vertical type, size 100 mm 4 lever complete all as specified as directed |
| 34 | S&F Stainless Steel butt hinges medium weight of size 75 mm complete all as specified and directed. |
| 35 | S&F Stainless Steel butt hinges medium weight of size 100 mm complete all as specified and directed. |
| 36 | S&F 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 37 | S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 38 | S&F Extruded aluminium alloy handles 100 mm long fabricated type anodised complete all as specified and directed . |
| 39 | S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . |
| 40 | S&F 200 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 41 | S&F for Floor door stopper 150mm of brass body and tongue with hard drawn steel spring aluminium alloy body with hard drawn steel spring, fixed in floor complete all as specified as directed. |
| 42 | S & F in repair Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed Aluminium (extruded section)body complete all as specified as directed. |
| 43 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed. |
| 44 | Taking down cement plaster of any description on brick or stone walls or from concrete surface incl raking out joints, hacking for key, scrubbing down with water etc all as specified,and removing unserviceable material outside cantt area complete all as specified and directed. |
| 45 | M&L for rendering 15 mm thick in CM (1:6) on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed . |
| 46 | M&L for rendering 15mm thick on brick work or concrete surfaces of wall in cement mortar (1:4) finished surface even and smooth without using extra cement complete all as directed. |
| 47 | M&L for 2mm thick wall care putty on wall surface complete all as specified and directed. |
| 48 | M & L for preparation of old wood or wood based surface and applying one coat of synthetic enamel paint , complete all as specified and directed. |
| 49 | M & L for preparation of old wood or wood based surface and applying two coats of synthetic enamel paint , complete all as specified and directed. |
| 50 | M & L and preparation of of new surfaces of wood and applying two coats of synthetic enamel paint on wood/wooden based surfaces over one coat of pink primer including preparation of new surfaces over 10 cm width or girth complete all as specified and directed. |
| 51 | M&L for preparation of old steel surfaces exc 10cm width or girth and applying one coat of synthetic enamel paints all as specified. |
| 52 | M&L for preparation of old steel surface/truss surfaces exc 10cm width or girth ( above 10mtr and upto 20mtr bldg height) and applying one coats of synthetic enamel paints all as specified. |
| 53 | M&L for preparation of old steel surface/truss surfaces exc 10cm width or girth ( above 10mtr and upto 20mtr bldg height) and applying two coats of synthetic enamel paints all as specified. |
| 54 | M&L for preparation of old steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints all as specified. |
| 55 | M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxid zinc crome primer all as specified. |
| 56 | M&L for preparation of old surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed. |
| 57 | M&L for preparation of old surfaces of wall and applying two coats of oil bound distemper complete all as specified and directed. |
| 58 | Material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed. |
| 59 | Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed. |
| 60 | M & L for preparation newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint on plastered surfaces complete all as directed. |
| 61 | M & L for preparation old plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint on plastered surfaces complete all as directed. |
| 62 | M & L for preparation newly plastered surfaces of wall and applying three coats of white wash over a coat of chalk whiting priming paint on plastered surfaces complete all as directed. |
| 63 | M & L for preparation old plastered surfaces of wall and applying two coats of white wash over a coat of chalk whiting priming paint on plastered surfaces complete all as directed. |
| 64 | Dismantling structural steel work in- cluding doors, gates but excluding framed truss etc complete all as specified and directed. |
| 65 | M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified as directed. |
| 66 | M&L for MS TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as reinforcement complete all as specified & directed. |
| 67 | Supply & Fixing for 10mm thick polycarbonate multiwall sheet as in roof with UV coated fixed with MS flats top and bottom rubber gasket and screws 25mm long all as specified and directed . |
| 68 | M&L pre-cast reinforced cement concrete (1:2:4) type B1(using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc set in CM (1:6) including necessary forms, moulds etc complete all as directed . |
| 69 | M&L providing pre-cast cement concrete (1:2:4) Type B0 (using 12.5 mm graded crushed stone aggregate) louvers and jallies, 55 mm thick (measured solid), including all moulding but excluding frame and set in cement mortar (1:4) complete all as specified & directed. |
| 70 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 71 | M&L screed bed or bedding layer 15 mm thick in cement mortar (1:6) on floors for laying floor finish complete all as specified and as directed. |
| 72 | M&L 10 mm thick plastering in cement mortar (1:4) brick or on concrete surfaces of wall and finishing the surfaces fair and even without using extra cement all as specified and directed as in screed bed of tiles. |
| 73 | M&L dark shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick in CM (1:6) as screed bed as in floor complete all as specified and directed compete all as specified and directed. |
| 74 | M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match compete all as specified and directed.(Note :- Screed bed shall be measured and paid separately under respective item) |
| 75 | M&L Granite (of any type) tiles, 20 mm thick machine cut laid over cement screed as in floor and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishing complete all as specified and directed (Note :- Screed bed shall be measured and paid separately under respective item) |
| 76 | M&L coloured Glazed ceramic tiles in vertical surface 300 x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed. (Note : Screed bed or bedding layer shall be measured and paid separately under respective items in this schedule). |
| 77 | Cleaning of 500 litres capacity PVC water storage tank by taking down existing inlet and outlet pipes, setting aside the tank and cleaning, rubbing down and removing all scales and dirt, mud and any other foreign materials etc from inside complete incl writing letter on PVC tank as TANK CLEANED ON ____ Dt, Month and year complete all as specified and as directed. |
| 78 | Cleaning of 1000 litres capacity PVC water storage tank by taking down existing inlet and outlet pipes, setting aside the tank and cleaning, rubbing down and removing all scales and dirt, mud and any other foreign materials etc from inside complete incl writing letter on PVC tank as TANK CLEANED ON ____ Dt, Month and year complete all as specified and as directed. |
| 79 | Cleaning of 2000 litres capacity PVC water storage tank by taking down existing inlet and outlet pipes, setting aside the tank and cleaning, rubbing down and removing all scales and dirt, mud and any other foreign materials etc from inside complete incl writing letter on PVC tank as TANK CLEANED ON ____ Dt, Month and year complete all as specified and as directed. |
| 80 | S&F rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position of 500 Ltr capacity all as specified in SSR including taking down old one complete all as specified and as directed. |
| 81 | S&F rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position of 1000 Ltr capacity all as specified in SSR including taking down old one complete all as specified and as directed. |
| 82 | S&F rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position of 2000 Ltr capacity all as specified in SSR including taking down old one complete all as specified and as directed. |
| 83 | S&F PVC tank cover of any size complete all as specified and as directed including taking down old one. |
| 84 | S&F Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and as directed including taking down old one. |
| 85 | S&F Plastic water closet seat cover for wall hang WC/ceramic commode with cistern, white, closed pattern with flat bottom of , and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and as directed including taking down old one. |
| 86 | S&F 15 mm dia swan neck pillar taps, cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without letter 'Hot' or Cold' with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed including taking out old one. |
| 87 | S&F in repair Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fency type screwed for iron pipe, suitable for 15 mm bore complete all as specified. |
| 88 | S&F in repair Bib tap short body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fency type screwed for iron pipe, suitable for 15 mm bore complete all as specified. |
| 89 | S&F soap dish holder, stainless steel, fancy type chromium plated complete all as specified and as directed including taking out old one. |
| 90 | S&F tubular/towel rail 20 mm dia brass chromium plated 60 cm long between flange brass CP fixed with and incl chromium plated brass screws and wooden plastic cleats all as specified and directed including taking down old one. |
| 91 | S&F towel rail with towel rack with hooks brass chromium plated 60 cm long between flange brass CP fixed with and incl chromium plated brass screws and wooden plastic cleats all as specified and directed including taking down old one. |
| 92 | S&F towel ring rail with 30cm dia brass chromium plated flange brass CP fixed with and incl chromium plated brass screws and wooden plastic cleats all as specified and directed including taking down old one. |
| 93 | S&F brass ball valves 20 mm dia high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed including taking out old one. |
| 94 | S&F 25mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking down old one complete all as specified and as directed. |
| 95 | S & F in repairs Stop valves cast copper alloy 15 mm dia, screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions and fixed all as specified and directed |
| 96 | S & F in repair angle cock or stop Valve cast copper alloy fancy two in one type15 mm dia bore with capstan handle screwed down screwed for iron pipe or for brass ferrule fixed complete all as specified and as directed. |
| 97 | S & F in repair Angle / Stop Valve cast copper alloy fancy type15 mm dia bore with capstan handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 98 | S&F 100 mm dia brass chromium plated shower rose fixed to steel pipe or union complete all as specified and directed including taking out old one. . |
| 99 | S&F wall mixture, cast copper alloy, screwed down, high pressure (chromium plated), with connecting legs, flanges etc. complete for fixing with 15 mm dia pipe, complete all as specified and directed including taking down old one. |
| 100 | S&F for PVC hot and cold water supply connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and as directed. |
| 101 | S&F chromium plated health faucet ABB body with 8 mm dia. 1.00 m long CP flexible pipe 15 mm bore with wall hook complete all as specified and directed including taking down old one. |
| 102 | S&F chromium plated hand shower 100 mm dia multy flow, ABB body with 8 mm dia. 1.5 m long CP flexiable pipe 15 mm bore complete all as specified and directed including taking down old one. |
| 103 | S&F stop valves (chromium plated fancy type) with long shank and cup (concealed type) 15 mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handles, screwed both end for iron pipe or for unions complete all as specified and directed including taking out old one. |
| 104 | S&F brass spindle for bib tap for 15 mm bore complete all as specified and directed including taking down old one. |
| 105 | S&F brass spindle for pillar tap for 15 mm bore complete all as specified and directed including taking down old one. |
| 106 | S&F brass spindle for stop cock for 15 mm bore complete all as specified and directed including taking down old one. |
| 107 | S&F 10 Ltr capacity PVC valveless syphonic action type dual flush type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as required and as directed including taking down old one |
| 108 | S&F 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed including taking out old one. |
| 109 | S&F waste coupling of PTMT half or full threaded with 32 mm dia complete all as specified and directed (Minimum weight - 45gms) including taking out old one. |
| 110 | S & F PVC flush / waste pipe 32 mm dia 1150 mm long fixed to walls complete all as specified and as directed including taking down old one. |
| 111 | M&L PVC float of low level flushing cistern complete all as specified and directed including taking out old one. |
| 112 | S & F PTMT Shelf, 450 mm long fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 300 grms) complete all as specified and directed. |
| 113 | S & F 40mm dia cupboard knobs fixed nut, screw and washer of mild steel, bright polished complete all as specified and as directed. |
| 114 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engr-in-charge. |
| 115 | S&F 5.5 mm thick Bevelled edge mirror (size-600mmx450mm) of selected quality glass, mounted on 6 mm thich AC building board or commercial plywood with wooden beading all around and fixed to wooden plugs with chormium plated brass screws and cup washers complete all as spfd and directed by Engr- in- Charge. |
| 116 | S&F in repair vitreous China Wash down water closet pan (EWC), white fixed with brass screws with necessary connection with water line and sewer line etc. complete including S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed including taking out old one. |
| 117 | S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with CI trap of suitable size (P or S type) including connection to trap and to flushing pipe, anti symphonic pipe etc complete including provision of lime concrete bedding & making good to floor complete complete all as specified and directed including taking out old one. |
| 118 | S&F in repair vitreous China Wash Basin, white, flat back of size 550 x 400 mm including suitable size of CI brackets, brass chromium plated waste fittings 32 mm dia with long screw shanks and fly nuts, flange and bedded in red lead cement complete all as specified and directed including taking down old one. |
| 119 | S&F vitreous China urinals, bowl type, flat back of size 465 x 355 x 265 mm (minimum) white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinals against wall in CM (1:2), screwing urinal to plug etc. complete all as specified and directed by including taking out old one. |
| 120 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 121 | M&L brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and as directed. |
| 122 | M&L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specified and directed. |
| 123 | M&L PCC 1:2:4 type B1 type (using 20 mm graded crushed stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed. |
| 124 | M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed. |
| 125 | Supply & fixed Maple laminated wooden flooring in size 1227mm x 197mm x 25mm thick including, flooring, breakers etc complete all as per manufacturers instruction with a layer of foam backing complete all as specified and as directed by Engr-in-Charge. |
| 126 | M & L PCC (1:2:4) type B1 type (using 20 mm graded crushed stone aggregate) as in coping incl all necessary form work as required, complete all as specified and directed. |
| 127 | M&L cement concrete type D-2 1:4:8 using (40mm graded aggregate) in foundation filling and mass concrete all as specified and as directed by Engr-in-Charge |
| 128 | M & L for sand filling under floor or foundation for watering and consolidation all as specified and as directed by Engr-in-Charge |
| 129 | M&L chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments as in floor complete all as specified and directed. (Note : Screed bed or bedding layer shall be measured and paid separately under respective items in this schedule). |
| 130 | S&F Stainless steel plate rack of size 1200mmx900mmx250mm made out of 1mm thick stainless steel sheet complete all as specified. Make:-Prestige / Devidayal/Nirali Please Enable Macros to View BoQ information |
