|
| 1 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required. |
| 2 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 3 | Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size in the existingRCC/HUME/METAL pipe as required. Up to 35 sqmm |
| 4 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Up to 35 sqmm |
| 5 | S/L of following size DWC HDPE Pipe ISI marked along with all accessories like socket ,bend ,couplers etc.conforming to IS 14930 ,part II complete with fitting and cutting ,jointing etc .direct in ground (75 cm below ground level )including excavation and refilling the trench but excluding sand cushioning and protective covering etc, complete as required (a)63mm dia (OD-63mm ID -51mm nominal ). |
| 6 | Providing and laying of HDPE PIPE OF 40mm outer dia with PN 4 rating by hand Moling/Mannual method Confirming to IS 4984 592 |
| 7 | Supply of XLPE insulated, PVC sheathed Al. Conductor Armoured cable 1.1 KV grade confirming to IS-7098 of following Size (a) 2 X 6 Sq. mm |
| 8 | Supplying, installation, Testing & Commissioning of Street light LEDfixture, powder coated pressure die cast aluminum body with built in orseparate driver as per the requirement with Driver efficiency >85%, Inputvoltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP66,IK-10, CRI >80 , under voltage and over voltage protection,EMIEMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III asper the width of the road and the project requirement., suitable to fit in up to65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum50000 Burning Hours with 70% of initial Lumen maintained till lifeends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K /4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(StandardDeviation Color Matching) <5, Maximum power consumption should notmore than the specified rating and Fixture shall be of relevant BIS standardcomplete in all respect i/c connections with 1.5 sq mm FRLS, PVCinsulated copper conductor single core cable and earthing etc. as requiredwith Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Wattoutput . LM79 & LM80 Test report from NABL lab for all testing requiredfor LED fixtures as per BIS shall be submitted. Shape size and CCT shall beas approved by Engineer-in-Charge as per requirement. (Thermalmanagement: heat sink of aluminum housing such that LED junctiontemperature shall not rise above 90°C).. 45 watt |
| 9 | Fabrication, supplying and fixing class B galvanised single overhang arm bracket made out of 250 mm long galvanized top tube with cap and 250 mm long 32 mm dia galvanised pipe with tightening bolts complete as required. |
| 10 | Fabrication, supplying and fixing class B galvanised double overhang arm bracket made out of 250 mm long galvanized top tube with cap and 250 mm long 32 mm dia galvanised pipe with tightening bolts complete as required. |
| 11 | Supplying & drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required .(a) 3 x 1.5 sq. mm |
| 12 | Fabrication, supply & erection of 4.0 mtr height minimum 3 mm thick bottomdia of 130 mm and to dia of 70 mm base plate of size 225x225x12 mm thickflange mounted hot dip galvanized octagonal pole made from HT steel plate,window with flash cover with full vertical window cover at appropriate height fromthe base plate on existing cement concrete pedestal as required. i/c supplyingand fixing of 6 mm thick laminated mounted sheet inside the window mountedon and i/c providing and welding 3 nos. GI strips 4 mm thick of suitable lengthand having suitable size tapped holes as reqd, terminal block suitable for 25 sqmm conductor - 4 nos. & shorting links on DIN channel i/cpdg and fixing DINchannel of suitable length,, 6 Amp. SPMCB 'C' characteristics, earth stud, cablesupport clamp suitable for upto 4x25 sqmm cable. Logo/Name of manufacturershall be embossed on the pole. Galvanization as per relevant IS. code etc asreqd. |
| 13 | Providing and laying in position M25 grade reinforced cement concretefoundation of size 450 mm (L) x450 mm wide and 1000 mm deep i/c excavationof earth, providing cutting, bending and placing in position, reinforcement of coldtwisted bars of 12 mm dia- 960 mm long(approx)-8 nos. and reinforcement ofcold twisted bars of 8 mm dia- 1400 mm (approx) -6 nos.(with 150 mm spacing)as required with supplying and positioning of 4 nos. foundation bolts 16 mmdia,600 mm long, J type i/c 2 nos. template anchor plates of size225mmx225mmx3mm and providing DCW HDPE for cable entry and exit asrequired for 3 m and 5 mtr pole. |
| 14 | Providing and fixing of stainless steel name plate of size 6 X 8 sq inch made of 20 guage sheet including engraved name of area representative duly painted along SS clamp nut bolt etc. as required |
| 15 | Supplying and fixing of light class GI pipe of 50 mm dia (nominal) 3 meters length along the pole for protection of under ground cable as required. |
| 16 | Providing and fiving name board made of MS Sheet 90x60cm, 1mm thick with frame of MS angle 50x50x6mm, two diagonal braces at the back of the sheet of MS flat 40x6mm, total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) 30x30x45cm including excavation and removal of surplus earth with in 50m lead, applying priming coat of approved steel primer, painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved colour (one side) as per drawing/direction of Engineer-in-Charge Please Enable Macros to View BoQ information |
