|
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 2 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 1200 mm |
| 3 | Providing and fixing Gypsum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board |
| 4 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls plete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 5 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 6 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.(Exterior and interior) |
| 7 | SOLID DISH LANDING TABLE WITH CHUTE BOTTOM CROSS SUPPORT AND REAR SPLASH:16G SS SUNK-IN TOP ON THREE SIDES 32x32x3mm THICK ANGLE FRAME 38MM dia 16G SS PIPE LEGS WITH ADJ. NYLON BULLET FEET 025MM dia x 16G SS PIPE CROSS SUPPORTS 16G SS REAR SPLASH REAR SIDE SS ANGLE RROVID A CHUTE 170 MM DIA |
| 8 | THREE SINK UNIT WITH BOTTOM CROSS SUPPORT AND REAR SPLASH :16G SS SUNK IN TOP ON THREE SIDES 32x32x3mm THICK MS ANGLE FRAME 3 Nos.16G SS SINK OF SIZE 450x450x300 mm DEEP WITH DRAIN COUPLING dia 38MM 16G SS PIPE LEGS WITH An NYLON BULLET FEET dia 25mm 16G SS PIPE CROSS SUPPORTS 16G SS SPLASH SS ANGLE FRAME |
| 9 | DISH STORAGE RACK (14Tier):4 Nos.18G SS SHELVES DOWN BEEDED ON ALL SIDES 18*75*18*16G SS CHANNEL UNDER SUPPORT 38MM DIA 16G SS PIPE UPRIGHTS WITH ADJ.NYLON BULLET FEET |
| 10 | WORK TABLE WITH SINK ONE UNDER SHELF & REAR SPLASH:G SS TOP DOUBLE BEEDED ON 3 SIDES 32x32x3mm THICK SS ANGLE FRAME 038MM 16G SS PIPE LEGS WITH ADJ.NYLON BULLET FEET.18G SS UNDERSHELF DOWN BEEDED18*75*18 16G SS SPLASH |
| 11 | PREPARATION TABLE WITH ONE UNDER SHELF: 16G SS TOP DOUBLE UNDER SHELF: 16G SS TOP DOUBLE BEEDED ON THREE SIDES 32x32x3mm THICK ANGLE FRAME 038MM 16G SS PIPE LEGS WITH ADJ. NYLON BULLET FEET 18G SS UNDERSHELF DOWN BEEDED ON ALL SIDES 18G SS CHANNEL OF SIZE 18x75x18 |
| 12 | SPREADER TABLE WITH BOTTOM SHELF AND REAR SPLASH :16G SS TOP DOUBLE BEEDED ON 3 SIDES 32x32x3mm THICK SS ANGLE FRAME DIA 38MM 16G SS PIPE LEGS WITH ADJ.LNYLON BULLET FEET.18G SS UNDERSHELF DOWN BEEDED ON ALL SIDES 18G SS CHANNEL OF SIZE 18*75*18 16G SS SPLASH |
| 13 | TWO BURNER CHINESE COOKING RANGE WITH BOTTOM SHELF AND REAR SPLASH : 16G SS SUNK-IN TOP ON THREE SIDES 32x32x3MM THICK ANGLE FRAME 18G SS PIPE LEGS WITH ADJ.NYLON BULLET FEET 18G SS UNDERSHELF DOWN BEEDED ON ALL SIDES 18G SS CHANNEL OF SIZE 18x75x18 16G SS SPLASH |
| 14 | SS TANDOOR :TOP & UPRIGHT 16SWG SS SIDES 20G SS CONTROL PANEL SS CONTROL PANEL INNER LINING OF CONVENTIONAL EARTHERN POT & PERFECT INSULATION FUEL GAS/CHARCOLE 100MM DIA CASTOR TYPE: HSC/PT/P4/RB LOAD CAP: 250KG/CASTOR 18G SS CONTROL PANEL FRAME SS PANELS ON ALL SIDESWITH |
| 15 | BULK COOKING RANGE : 16G SS TOP,DOUBLE BEEDED ON ALL SIDES 32*32*3MM THK. CAST IRON VESSEL REST OF SIZE 500*500mm 18G SS FRONT 38MM DIAx16G SS PIPE LEGS WITH ADJ. NYLON BULLET FEET 20G SS ON BOTH SIDES AND REAR WITH AIRVENTS BURNER 3 NO. HP T-35 BURNER WITH PILOT |
| 16 | EXHAUST HOOD WITH FILTERS-WALL MOUNTED TYPE FOR TWO BURNER /HOT PLATE/CHINEESE |
| 17 | EXHAUST HOOD WITH FILTERS -WALL MOUNTED TYPE FOR TANDOOR |
| 18 | EXHAUST HOOD WITH FILTERS -WALL MOUNTED TYPE FOR BULK COOKING RANGE |
| 19 | 2 HP AXIAL FLOW FAN -3 HP MOTOR AND WITH NECESSARY FITTINGS |
| 20 | GI DUCTING FOR EXHAUST SYSTEM WITH NECESSARY FITTINGS UP TO KITCHEN OUTER LEVEL. |
| 21 | Providing and fixing fly proof gauze to windows,clerestory windows,Doors and ventilators with M.S Flat 15x3mm and nuts and bolts Complete.Galvanised M.S wire gauze with 0.63mm dia wire and 1.4mm aperture on both sides |
| 22 | Supply and fixing of Exposed type air curtain with smooth front panel and hidden inlet of dimension 1034x210x380 mm with airflow 1200-2900 m2/h range 2.2 to 2.8 m heating capasity E3,8-11.3KW P:8.2-16.7 KW, with Manual regulator +IR remote control, noise level 35-54 dB(A) all specification complete. Please Enable Macros to View BoQ information |
