|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding1.5 m in width or 10 sqm on plan) including dressing of sides andramming of bottoms, lift upto 1.5 m, including getting out theexcavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m. : |
| 2 | All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, leadup to 50 m and lift upto 1.5 m. |
| 4 | Supplyingandfillinginplinthwithsandysoilunderfloorsincluding,watering,ramming consolidating and dressing complete. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering --All work upto plinth level: |
| 6 | 1:4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mmnominal size) |
| 7 | 1:2:4 ( 1 Cement: 2 coarse sand : 4 graded stone aggregate 20 mmnominal size) |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 9 | Foundations, footings, bases of columns, etc. for mass concrete |
| 10 | Brickwork with Ist class common burnt clayF.P.S.(nonmodular)bricks in foundation and plinth in: |
| 11 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 12 | Half brick masonry with Ist class common burnt clay F.P.S.(nonmodular)bricks in superstructure above plinth level upto floor V level in |
| 13 | Cement mortar 1 : 3 (1 cement : 3 coarse sand) |
| 14 | Steel work in builtup tubular (round, square or rectangular tubes etc.)trussesetc.,including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc.complete. |
| 15 | Hot finished welded type tubes |
| 16 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. |
| 17 | Ingrating, frames, guardbar, railing, brackets, gates and similar works. |
| 18 | Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)with zinc coating 120 grams per sqm as per IS: 277, in 240 mpasteel grade, 5-7 microns epoxy primer on both side of the sheetand polyester top coat 15-18 microns. Sheet should haveprotective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto12 metre or as desired by Engineer-in charge. The sheet shall befixed using self drilling /self tapping screws of size (5.5x 55 mm)with EPDM seal,complete upto any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trussesand including cutting to size and shape wherever required with |
| 19 | Precoated galvanised iron profile sheets 0.4 mm thick |
| 20 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominalsize) over 75mm bed of dry brick ballast 40mm nominal size wellrammed and consolidated and grouted with fine sand includingfinishing the top smooth. |
| 21 | Brick edging 7cm wide 11.4cm deep to plinth protection with Istclass common burnt clay F.P.S. (non modular) bricks includinggrouting with cement mortar 1:4 (1 cement: 4 fine sand). |
| 22 | 12 mm cement plaster of mix: |
| 23 | 1:4 (1 cement : 4 fine sand) |
| 24 | 15 mm cement plaster on rough side of single or half brick wall ofmix:- |
| 25 | 1:4 (1 cement : 4 fine sand) |
| 26 | Providing and fixing panelling or panelling and glazing in panelledor panelled and glazed shutters for doors, windows and clerestorywindows (Area of opening for panel inserts excluding portioninside grooves or rebates to be measured). Panelling for panelledor panelled and glazed shutters 25 mm to 40 mm thick |
| 27 | Float glass panes |
| 28 | 4mm thick glass panes |
| 29 | Providing and applying white cement based putty of averagethickness 1mm,of approved brand and manufacturer, over theplastered wall surface to prepare the surface even and smoothcomplete. |
| 30 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: |
| 31 | One or more coats on old work |
| 32 | Applying priming coats with primer of approved brand and manufacture,having low VOC(VolatileOrganicCompound) content. |
| 33 | With water thinnable cement primer on wall surface having VOCcontent less than 50 grams/litre |
| 34 | Providing woodwork in frames of doors,windows,clerestorywindows and otherframes,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length(hold fast lugs or dash fastener shall be paid for separately : |
| 35 | Local best quality Uningthou wood |
| 36 | Wall painting with plastic emulsion paint of approved brand andmanufacture to give an even shade. |
| 37 | Two or more coats on new work- |
| 38 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 39 | One or more coats on old work |
| 40 | Providing and fixing aluminium handles, ISI marked,anodised(anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour or shade with necessaryscrews etc. complete : |
| 41 | 125 mm |
| 42 | Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per IS : 1868 )transparent or dyed to required colour or shade with necessaryscrews etc. complete : |
| 43 | 250x10 mm |
| 44 | Providing and fixing aluminium sliding door bolts ISI markedanodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nutsand screws etc. complete : |
| 45 | 250x16 mm |
| 46 | Providing and fixing 1st quality ceramic glazed wall tilesconforming to IS : 15622 (thickness to be specified by themanufacture of approved make in all colours, shades exceptburgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thickbed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointingwith grey cement slurry @ 3.3kg per sqm including pointing inwhite cement mixed with pigment of matching shade complete. |
| 47 | Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 48 | Flexible pipe |
| 49 | 32 mm dia |
| 50 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. |
| 51 | External work |
| 52 | 20 mm nominal outer dia Pipes |
| 53 | 25 mm nominal outer dia Pipes |
| 54 | Providing and fixing C.P. brass bib cock of approvedquality conforming to IS 8931 |
| 55 | 15 mm nominal bore |
| 56 | Providing and fixing C.P. brass sngle valve for basin mixer and geysers points of approvedquality conforming to IS 8931 |
| 57 | 15 mm nominal bore |
| 58 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and makinggood the walls wherever required: |
| 59 | White Vitreous China Wash basin size 550x400 mm with a pair of15 mm C.P.brass pillar taps |
| 60 | Providing and fixing PTMT to welrail complete with brackets fixed to wooden cleats with Cpbrass screws with concealed fittings arrangement of approved quality and colour. |
| 61 | 450 mm long towel rail with total length of 495 mm, 78 mm wideand effective height of 88 mm, weighing not less than 170 gms |
| 62 | Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms. |
| 63 | Providing and fixing white vitreous china pedestal type watercloset (European type W.C. pan) with seat and lid, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever), conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required : |
| 64 | W.C. pan with ISI marked white solid plastic seat and lid. |
| 65 | Providing and laying Vitrified tiles in floor in different sizes(thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS:15622, ofapproved brand & manufacturer, in all colours and shade, laid on20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointingwith grey cement slurry @3.3 kg/sqm including grouting thejoints with white cement and matching pigments etc. The tilesmust be cut with the zero chipping diamond cutter only . Laying oftiles will be done with the notch trowel, plier, wedge, clips ofrequired thickness, leveling system and rubber mallet for placingthe tiles gently and easily. |
| 66 | Double charge vitrified tile polished finish of size |
| 67 | Size of Tile 600 x 600 mm |
| 68 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as permanufacturers specifications |
| 69 | Painting Steel work with Deluxe Multi Surface Paint to give an evenshade. Two or more coat applied @ 0.90 ltr/10 sqm over an undercoat of primer applied @ 0.80 ltr/10 sqm of approved brand andmanufacture |
| 70 | Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive), as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers Of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the spacing of 1200mm centre to centre; to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.l. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.l. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre,with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng to a flush finish of tapered and square edges of the board with recommended jointing compoundjointing tapes, finishing with jointing compund in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board,all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, and specification and direction of theEngineer in Charge but excluding the cost of painting with : |
| 71 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I, |
| 72 | Providing and fixing 18mm thick gang saw cut . mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters ,window sills , facias and similar locations of requirede of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. |
| 73 | Area of slab over 0.50 sqm. |
| 74 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with G.l. brackets and stainless steel plug 40 mm, including painting of fittings .and brackets; cutting and making good the walls wherever required : |
| 75 | Kitchen sink without drain board |
| 76 | 470x420 mm bowl depth 178 mm |
| 77 | Banking excavated earth in layer not exceeding 20cm in depth breaking clods watering, rolling each layer with 1/2 tonne roller or wooden or steel rammer and rolling every third and topmost layer with power roller of min. 8 tonne and dressing up in embankments for roads marginal banks , flood banks & guide bank lead upto 50 m. and lift upto 1.5 m. |
| 78 | all kinds of soil |
| 79 | Granular base / sub-base using naturally occurred sand gravel |
| 80 | Providing, laying and compacting granular base / sub-base according tolines, grades and cross sections by using naturally occurred sandgravel/conforming to IRC-Grd'II of MOST specification free from organic or other deleterous constituent spread with motor grader and compacted by rolling with power roller of 8-10 capacity in layers not exceeding 150mm (spread thickness) i/c rolling of the road surface to proper level and grades 30 cm width edging on both side etc. complete as directed by Engineer-incharge. |
| 81 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density |
| 82 | By Manual Means |
| 83 | Grading-I |
| 84 | Using Screening Type-A (13.2 mm agg.) |
| 85 | Grading-II |
| 86 | Using Screening Type-B (11.2 mm agg.) |
| 87 | Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface andspraying primer at the rate of 0.60 kdsqm using mechanical means.) |
| 88 | Prime Coat on WMM /WBM |
| 89 | Providing and applying primer coat with bitumen emulsion onprepared swface of granular Base including clearing of roadsurface and spraying primer at the rate of 0.70 kg/sqm usingmechanical means. |
| 90 | Tack coat |
| 91 | Tack Coat on Granular surfaces treated with primer |
| 92 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. |
| 93 | Open - Graded Premix Surfacing (Providing, laying and rolling of open -graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6mm aggregates using Viscocity grade bitumen to required tine, grade andlevel to serye as wearing course on a previously prepared base, includingmixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-l0 tonne capacity, finished to required level and grades.) |
| 94 | Case - I: Mechanical method using Penehation grade Bitumenond HMP of appropriate capacity not less than 75 tonnes/hour . |
| 95 | Seal Coat (Providing and laying seal coat sealing the voids in a bituminoussurface laid to the specified levels, grade and cross fall using Type A and Bseal coats) |
| 96 | Case - II : Type B (Providing and laying of premix sand seal coat with HMP of appropriate capacity not less than7l tonnes/ hoursusing crushed stone chipping 6.7 mm size and penetrationbitumen of suitable grade.) Please Enable Macros to View BoQ information |
