|
| 1 | Taking down cement plaster/ terrazo finish on brick wall including racking out joints, hacking for keys scrubbing down with water all as specified and directed by Engineer - in - Charge.Note:- The rates quoted by the contractor shall include scaffolding, necessary formwork upto G+5 storey building. |
| 2 | M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even & fair without using extra cement all as specified and directed by Engineer - in - Charge .Note:- The rates quoted by the contractor shall include scaffolding, necessary formwork upto G+5 storey building. |
| 3 | M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & fair all as specified and directed by Engineer - in - Charge .Note:- The rates quoted by the contractor shall include scaffolding, necessary formwork upto G+5 storey building. |
| 4 | M & L rendering 10mm thick on fair faces of brick work or concrete surfaces of ceiling in CM 1:3 finished even & fair all as specified and directed by Engineer - in - Charge . |
| 5 | Cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc; and cuttings chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth all as specified and directed by Engineer-in - Charge. |
| 6 | M & L two coats of distemper oil emulsion over a coat of primer and wall putty (Asian / JK / Birla), preparatory to distempering, on newly plastered surfaces of walls including preparation of surfaces all as specified and directed by Engineer - in - Charge. |
| 7 | M & L two coats of distemper oil emulsion over a coat of primer and wall putty (Asian / JK / Birla), preparatory to distempering, on newly plastered surfaces of ceiling including preparation of surfaces all as specified and directed by Engineer - in - Charge. |
| 8 | S & F 150mm dia sand cast iron soil waste and vent pipes in any length with or without ears with drip seal solvent joints fixed to walls with complete fittings and fixed complete all as specified and directed by Engineer - in – Charge. |
| 9 | Demolition and breaking upto 150mm bore drain pipes (salt glazed ware or AC pipe set) in cement mortar and taking out from walls all as specified and directed by Engineer - in – Charge. |
| 10 | Demolition and breaking upto 75/100mm bore drain pipes (salt glazed ware or AC pipe set) in cement mortar and taking out from walls all as specified and directed by Engineer - in – Charge. |
| 11 | S&F PVC (SWR) soil waste and vent pipe, single socketed, 110mm dia bore in any length with rubber ring joints, fixed to walls/ floor complete all as specified and directed |
| 12 | S&F PVC (SWR) soil waste and vent pipe, single socketed, 75mm dia bore in any length with rubber ring joints, fixed to walls/ floor complete all as specified and directed |
| 13 | S&F PVC (SWR) soil waste and vent pipe, single socketed, 160mm dia bore in any length with rubber ring joints, fixed to wall/ floor complete all as specified and directed |
| 14 | S&F PVC (SWR) bends any radius, bore of 75 mm with access door all as specified and directed by Engineer - in - Charge |
| 15 | S&F PVC (SWR) bends any radius, bore of 110 mm with access door all as specified and directed by Engineer - in - Charge |
| 16 | S & F PVC (SWR) 110 mm cowl complete all as specified and as directed. |
| 17 | S & F PVC (SWR) 110 mm bore Tee complete all as specified and as directed. |
| 18 | S & F PVC (SWR) 75 mm bore Tee complete all as specified and as directed. |
| 19 | S&F PVC (SWR) 110mm bore elbow all as specified and directed by Engineer - in - Charge |
| 20 | S&F PVC (SWR) 75mm bore elbow all as specified and directed by Engineer - in - Charge |
| 21 | S & F PVC (SWR) 150 x 110 mm Tee reducer complete all as specified and as directed. |
| 22 | S & F PVC (SWR) 100 x 75 mm Tee reducer complete all as specified and as directed. |
| 23 | Taking up or down steel tubing 15mm bore and connections including cleaning for refixing/ removal complete all as specified and directed by Engineer - in – Charge. |
| 24 | Taking up or down steel tubing 20mm bore and connections including cleaning for refixing/ removal complete all as specified and directed by Engineer - in – Charge. |
| 25 | S & F 15mm bore medium grade steel tubes galvanised with all fittings and fixed complete to walls & ceiling or laid in floor all as specified and directed by Engineer - in – Charge . |
| 26 | Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) 20mm bore all as specified and directed by Engineer - in - Charge. |
| 27 | S & F 20mm bore medium grade steel tubes galvanised with all fittings and fixed complete to walls & ceiling or laid in floor all as specified and directed by Engineer - in – Charge . |
| 28 | S & F grating round 100mm with waste hole of CP all as specified and directed by Engineer - in - Charge. |
| 29 | S&F in repairs vitreous china wash down water closet (Squatt pattern) White, including connection to trap and to flushing pipe, anti-syphonage pipe etc including making good to floor complete all as specified and as directed by Engineer-in-Charge. |
| 30 | S&F in repairs vitreous china wash down water closet (Padestal pattern) White, including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed by Engineer-in-Charge. |
| 31 | S&F in repairs vitreous china half stall urinal white with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws complete with PVC flush pipe and half turn valve 15mm bore cast copper alloy, fancy type, chromium plated all as specified and directed by Engineer - in - Charge. |
| 32 | S&F in repairs vitreous china urinal partition white of size 310 x 700mm all as specified and directed by Engineer - in - Charge. |
| 33 | S & F in repairs twin flush PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve and float including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and directed by Engineer - in - Charge . |
| 34 | S & F as in repairs toilet paper holder, brass chromium plated fixed to wall with chromium plated brass screws complete all as specified and as directed by Engineer-in-Charge. |
| 35 | S & F in repairs vitreous china wash basin with pedestal , white, flat back, size 550x400mm including waste fitting brass chromium plated, PVC connection and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets complete all as specified and directed by Engineer - in – Charge . |
| 36 | S & F in repairs 15mm bore stop cock, cast copper alloy screwed down, fancy type, chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge. |
| 37 | S&F in repairs CP fancy wall mixer with L bends (including provision of over head shower & hand shower) for mixing of hot & cold water screwed down for iron pipe 15mm bore and fixed with including hand shower and tube complete all as specified and directed. Cat part No. QQT-7281 of Jaguar or equivalent make Kohler/Marc |
| 38 | S & F in repairs PVC connection 15mm size with PTMT nuts of length 600mm all as specified and directed by Engineer - in – Charge. |
| 39 | S&F in repairs Pillar taps 15mm bore dia, fancy type, cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed by Engineer – in – Charge . |
| 40 | S&F in repair bib taps 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and directed by Engineer – in – Charge . |
| 41 | S & F in repairs 15mm bore angle valve, cast copper alloy screwed down, fancy type, chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge. |
| 42 | M&L in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 142 gm screwed for 15mm bore iron pipe supplied and fixed in repairs complete all as specified and as directed by Engineer-in-charge. |
| 43 | S & F 40mm bore Low density poly-ethylene pipes (LDPE) of pressure rating 6 kgf/cm2 laid in wall or floors with all fittings and fixed complete all as specified and directed by Engineer - in – Charge . |
| 44 | S & F as in repairs 15mm bore central hole basin mixer chromium plated brass for hot and cold water, fancy type with connection and nuts complete all as specified and as directed by Engineer-in-Charge. Make Cat part No. CQT-CHR-23167B of Jaquar or equivalent make of Parryware, Kohler or Marc |
| 45 | S & F in repairs brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges incldg brackets complete all as specified and directed by Engineer - in - Charge . |
| 46 | S & F as in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 47 | S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 20mm bore complete all as specified and directed by Engineer – in – Charge. |
| 48 | S & F as in repairs 25mm GI nipple suitable for HDPE water tank, minimum weight 38 grams including necessary drilling holes, etc fixed complete all as specified and directed by Engineer – in – Charge. |
| 49 | S & F as in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed by Engineer - in - Charge . |
| 50 | S & F as in repairs soap dish brass chromium plated, fixed to plugs with brass chromium plated screws complete all as specified and directed by Engineer - in - Charge. |
| 51 | S & F as in repairs brass chromium plated shower rose 125mm size with or without swivel joint any size including fixing to steel pipe or union all as specified and directed by Engineer - in - Charge. |
| 52 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 510mm bowl size 460mm x 460mm x 230mm with waste pipe PVC 40mm dia all as specified and directed by Engineer-in-Charge. |
| 53 | S&F as in repairs 32 mm waste coupling of PTMT (half or full threaded). (Minimum weight 32mm 45gms/ 40mm-60 gms) all as specified and directed by Engineer-in-Charge. |
| 54 | S&F as in repairs 32 mm waste coupling of PTMT for urinal (half or full threaded). (Minimum weight 32mm 45gms) all as specified and directed by Engineer-in-Charge. |
| 55 | S & F as in repairs 600 x 450 mm size beveled edge mirror 5mm thick of selected quality glass mounted on 6mm thick commercial plywood and fixed with wooden plugs with chromium plated brass screws and cup washers all as specified and directed by Engineer - in - Charge . |
| 56 | S&F as in repairs brass angle cock 15mm dia all as specified and directed by Engineer - in - Charge . |
| 57 | S & F as in repairs rotational moulded polythene water storage tanks, white colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres including 20mm brass ball valve all as specified and directed by Engineer - in - Charge . |
| 58 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed by Engineer - in - Charge. |
| 59 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engineer - in - Charge. |
| 60 | Demolition of brick work or stone/ boulder masonry built in cement mortar all as specified and directed by Engineer - in - Charge. |
| 61 | M&L Brick work with sub class 'B' old size burnt bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge . |
| 62 | Dismantling wrought iron or mild steel work of any description all as specified and directed by Engineer - in - Charge . |
| 63 | S & F Rolled sections conforming to Fe 290-W (Gde E- 165), quality-A, as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed by Engineer-in-Charge. |
| 64 | M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer - in - Charge . |
| 65 | Factory made SFRC Pre-cast RCC manholes covers EHD-35 of size 300mm X 300mm X 100 mm thick, conforming to IS-12592 duly fixed on manhole /gully trap opening complete all as specified. |
| 66 | Factory made SFRC Pre-cast RCC manholes covers EHD-35 of size 450mm X 450mm X 100 mm thick, conforming to IS-12592 duly fixed on manhole /gully trap opening complete all as specified. |
| 67 | Factory made SFRC Pre-cast RCC manholes covers EHD-35 of size 600mm X 600mm X 100 mm thick, conforming to IS-12592 duly fixed on manhole /gully trap opening complete all as specified. |
| 68 | Factory made SFRC Pre-cast RCC manholes covers EHD-35 of size 900mm X 450mm X 100 mm thick, conforming to IS-12592 duly fixed on manhole /gully trap opening complete all as specified. |
| 69 | M & L for 75mm thick cement concrete type D-2 (1:4:8) using 40mm graded stone aggregate as in sub floors, sub bases etc including finishing the surfaces even & rough all as specified and directed by Engineer - in - Charge. |
| 70 | M & L for chequered cement concrete designer prepolished glossy finished tiles 20cm x 20cm x 25mm thick with grey cement and pigments set, heavy duty, jointed and pointed in neat cement slurry and pigments as in floors over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed by Engineer - in – Charge. |
| 71 | Demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise specifically provided for all as specified and directed by Engineer - in - Charge . |
| 72 | Demolition of mud in sunken portion/ bathroom/ roof, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) all as specified and directed by Engineer - in - Charge. |
| 73 | M & L 10mm thick rendering in Cement Mortar 1:3 to concrete surface slab mixed with admixture of liquid water proofing compound as per manufacture's instruction per bag of cement on green concrete surface complete all as specified and directed by Engineer - in - Charge. Note:- The rates do not include for the supply of integral water proofing compound, which shall be paid for in addition at “supplied only rates separately, as applicable. |
| 74 | M & L cement concrete (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work etc. including cleaning and removing all dust from existing roof surface before placing of concrete all as specified and directed by Engineer - in - Charge. |
| 75 | Supply only liquid integral water proofing compound, complete all as specified. |
| 76 | Dismantling floor or wall tiles including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer - in – Charge. |
| 77 | M & L for glazed ceramic coloured tiles first quality, 350x250x7mm/ 450x350x7mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge. |
| 78 | M & L for non skid ceramic coloured tiles first quality, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge. |
| 79 | M& L dark shade/Double Charged/ultracharged Vitrified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:4 complete all as specified and directed by Engineer - in - Charge. |
| 80 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge |
| 81 | S & F Solid PVC door frame factory made of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube jointed , supplying and fixing in opening complete all as specified and as directed by Engineer-in-Charge |
| 82 | Factory made solid panel PVC Moulded Door Shutter, 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-Charge. |
| 83 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer - in - Charge . |
| 84 | S & F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in - Charge . |
| 85 | S & F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in - Charge . |
| 86 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge. |
| 87 | S & F Aluminium anodised barrel tower bolt of extruded section 150mm long all as specified and directed by Engineer - in - Charge |
| 88 | S & F Aluminium anodised barrel tower bolt of extruded section 100mm long all as specified and directed by Engineer - in - Charge |
| 89 | S & F Stainless steel handles, cast type, 150mm long all as specified and directed by Engineer - in - Charge. |
| 90 | S & F Stainless steel handles, cast type, 100mm long all as specified and directed by Engineer - in - Charge. |
| 91 | S & F Stainless steel sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or cast aluminium alloy 250mm size all as specified and directed by Engineer - in – Charge . |
| 92 | S&F as in repairs door closer hydraulically regulated, aluminium (extruded section) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width and of weight 61 to 80 kg complete all as specified and as directed by Engineer-in-Charge. |
| 93 | Material & Labour for providing and fixing stainless steel (Grade SS 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and aking curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
