|
| 1 | Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projection or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc including removing the waste out of defence land all as specified and as directed. |
| 2 | M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed. |
| 3 | M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4 finished even and smooth without using extra cement, using water proofing compound mix as per manufacturer detail, complete all as specified and as directed. (WPC measured and paid seperately) |
| 4 | M&L Rendering 5 mm thick on concrete surfaces in CM 1:3 finished on even and smooth without using extra cement as in ceiling, Chajja etc.complete all as specified and as directed |
| 5 | Material & Labour for RCC chajja/fascia/parapet repair by using following steps :-(a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed.(b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as specified and directed. |
| 6 | Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame complete all as specified and directed. |
| 7 | Taking down chowkats or frames exc. 1.5 sqm & n.exc. 4 sqm each but with shutter without taking off shutters from the frame complete all as specified and directed. |
| 8 | M&L for pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and directed. |
| 9 | M&L PCC (1:3:6) type C-2 (40 mm graded aggregate) filling back of chowkats complete all as specified and directed.. |
| 10 | M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed. |
| 11 | Mild steel framed work as in doors ( as in chowkats)or gates of angle or other section with guest plates rails, braces rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Fe-410- W(Gde- E-250) quality- B including shop coat of red oxide including preparation of surface before fixing complete all as specified and directed. |
| 12 | S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (Stile) with flush panel with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face all as spd & directed |
| 13 | S&F steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified. |
| 14 | S&F steel windows with side hung double shutters (window consisting of two shutters out side and two shutters of similar dimension inside of single MS Frame) box type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work) dovetailed or welded complete all as specified and directed. |
| 15 | S&F Galvanized mild steel wire cloth 0.45 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tank or galvanized wire staple complete all as specified and as directed. |
| 16 | S&F sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and as directed. |
| 17 | S&F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each complete all as specified and as directed. |
| 18 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 19 | S&F Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and as directed. |
| 20 | S&F Aluminium handles cast type anodised 150mm complete all as specified and as directed. |
| 21 | S&F Butt hinges 100mm medium weight stainless steel complete all as specified and directed by Engr in charge complete all as specified and as directed. |
| 22 | S&F Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm long complete all as specified complete all as specified and as directed. |
| 23 | S&F Aluminium handle cast type anodized of size 125mm complete all as specified complete all as specified and as directed. |
| 24 | S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm complete all as specified and as directed. |
| 25 | Dismantling floor, hearth or wall tiling , terrazzo topping on walls including cement mortar , bedding (but no backing) removing serviceable tiles and rubbish off the premises complete all as specified and directed. |
| 26 | M&L for sunken treatment with glass fiber reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) complete all as following :-Base Coat : Berger HS Latex plus (or equivalent)consumption base coat : 0.3 kg/m2Reinforcement : Glass fiberSecond and Third coat : Latex sheild 2K (or equivalent)Consumption top coat : 3 kg/m2System reqquirements : density : 2.00 kg/ltr;Compressive strength: 0.5N/mm2Wall penetration through the RCC slab must be sealed using Berger HS Repair (or equivalent).Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto sft.All depressions, unevenness, surface honeycombng shal be repaired using Berger HS Latex plus (or equivalent) modifiled polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry.Including cleaning of RCC surface to remove dust, loose paricles, etc with compressed air or any other suitable technique depending on site conditions, grinding aby sharp edges, etc.Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 95 of tender documents as per Sch 'A' Note No 19 Page No 17). |
| 27 | M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without usingextra cement complete all as specified and as directed (WPC to be measured and paid separately) |
| 28 | Supply only Integral water proofing compound liquid complete all as specified and as directed. |
| 29 | S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area complete all as specified and as directed. |
| 30 | M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of compacted thickness 150mm complete all as specified and directed. |
| 31 | M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and as directed. |
| 32 | M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed. |
| 33 | M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with Berger HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom complete all as specified and as directed. |
| 34 | Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed. |
| 35 | Demolition of cement concrete in and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed |
| 36 | M&L for 75 mm thick PCC 1:4:8 type D-2 using (40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed. |
| 37 | M&L for Precast designer coloured heavy duty full body paving tiles (factory made) of size 300mmx300mm x 10mm, top layer glazed made in any type of cement and pigment, in required patterns as approved by GE in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified & directed. |
| 38 | M&L Vitrified coloured tiles, jointless , light shade of size 600mm x 600mm x 9 to 10 mm thick, as in floors etc bedded & jointed in neat cement slurry over and including 10mm thick screed bed in cement mortar 1:6 and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed. |
| 39 | M&L Vitrified coloured tiles,joint less , light shade 600mm x 600mm x 9 to 10mm thick, on vertical surfaces such as skirting / dado etc bedded & jointed in neat cement slurry over and including 10mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles,complete all as specified and directed. |
| 40 | M&L for Non - skid ceramic coloured jointless tile 400mm x 400mm x 7mm thick as in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, all as specified and directed. |
| 41 | M&L for Non - skid ceramic coloured jointless tiles 400mm x 400mm x 7 mm thick on vertical surfaces such as skirting /dado etc bedded & jointed in neat cement slurry over and including 10 mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed. |
| 42 | M&L for Glazed ceramic coloured tiles of size 350x450x7 mm thick as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed. |
| 43 | Dismantling water tanks exceeding 500 ltr capacity but not exc 1000 ltrs complete all as specified & directed. |
| 44 | S&F Rotational molded polythene water storage tank triple layer vertical type with closed top hoisted and fixed in position all as spd in SSR part-I capacity 1000 liter complete all as specified & directed. |
| 45 | S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , brass rod & high density plastic ball screwed for iron pipe min wt 210 gms complete all as specified & directed. |
| 46 | Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store complete all as specified & directed. |
| 47 | Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store complete all as specified & directed. |
| 48 | S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, complete all as specified & directed. |
| 49 | S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, all as specified. |
| 50 | Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 15 mm dia complete all as specified and as directed. |
| 51 | Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 20 mm dia complete all as specified and as directed. |
| 52 | S&F Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet and integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed. |
| 53 | S&F PVC flushing cistern white shade low level 10 ltrs capacity, white with inlet ball valve, float and handle including bracket and flush pipe including connection to pipes, fixed in repairs complete all as specified and as directed. |
| 54 | S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified & directed. |
| 55 | S&F wall mounted bathroom glass looking mirror beveled edge of selected quality glass 5mm thick frameless with CP brass screws and cup washers etc, fixed in repairs complete all as specified & directed. |
| 56 | S&F Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified & directed. |
| 57 | S&F Stainless steel grating of 125mm size, male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, fixed in repairs, complete all as specified & directed. |
| 58 | S&F PVC 32mm dia waste pipe with CP coupling, all as spd & directed. |
| 59 | S&F Vitreous china wash basin white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets, fixed in repair, in RCC slabs as directed by Engr-in-charge complete all as spd & directed. |
| 60 | S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 61 | S&F in repair Bib taps, chromium plated cast copper alloy, with capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, all as specified and as directed. |
| 62 | S & Fixed in repairs Angle stop valve cast copper alloy, with fancy type chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete, all as specified and directed. |
| 63 | S&F in repair CP brass hot & cold 15mm dia wall mixture with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water Complete all directed by GE |
| 64 | S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed. |
| 65 | S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs complete all as specified & directed. |
| 66 | S&F Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long make Jaguar or equivalent complete all as specified & directed. |
| 67 | S&F 600x450mm PVC cabinet with mirror of superior quality complete all as specified and directed. |
| 68 | M&L for TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed. |
| 69 | M&L for TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed. |
| 70 | M&L for reinforced cement concrete type B1, 1:2:4 with 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves for WHB complete all as specified and directed. |
| 71 | Demolition of reinforced cement concrete ( reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 72 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for in plinth protection |
| 73 | M&L for 75 mm thick PCC 1:3:6 type C-1, (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement incl necessary joints complete all as specified and directed. |
| 74 | Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required complete all as specified and directed. |
| 75 | S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore complete all as specified and directed. |
| 76 | S&F PVC (SWR) pipes single socketed in any length to be fixed in trenches upto first manhole of 110mm bore complete all as specified and directed. |
| 77 | S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 75 mm bore complete all as specified and directed. |
| 78 | S&F PVC (SWR) bends any radius 110mm bore with access door complete all as specified and directed. |
| 79 | S&F PVC(SWR) junction single (single 'T') equal or unequal 110mm bore with access to door ccomplete all as specified and directed. |
| 80 | S&F PVC (SWR) bends any radius 75 mm bore with access door complete all as specified and directed. |
| 81 | S&F PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore with access to door ccomplete all as specified and directed. |
| 82 | M & L for PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement complete all as specified and directed. |
| 83 | M&L for Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed. |
| 84 | M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 85 | M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed. Please Enable Macros to View BoQ information |
