|
| 1 | Checking of LT Panel/Motor/Pump set for detecting any kind of fault and attending the fault immediately at any time round the clock and carry out certain repairs required as per site requirement and replacing of worn out parts by expert engineer complete all as specified and direced.Note :- Unit rate includes detecting of any kind of fault in LT Panel/Motor/Pump set only and cost of replacement of worn out parts shall be measured and paid separately under respective items of BOQ complete all as specified and directed. |
| 2 | Supply and fix in replacement starter for 1.5 to 2 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54, 230 Volt, Single Phase, with inbuilt amp & voltage meter, Rugged MU-2P contactor with wide band voltage, MU-2P Relay for reliable overload protection, heavy duty START & RUN condensers with FRLS internal wiring, and class H insulation complete all as specified and directed. |
| 3 | Supply and fix in replacement fully automatic star delta starter for 10 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,3 phase, 415 Volt, 50 Hz, relay range 6-10 amps type MK1, with FRLS internal wiring and class H insulation complete all as specified and directed. |
| 4 | All as per item No 3.00 above but 3 HP complete all as specified and directed. |
| 5 | All as per item No 3.00 above but 5 HP complete all as specified and directed. |
| 6 | All as per item No 3.00 above but 7.5 HP complete all as specified and directed. |
| 7 | Taking down UNSV Starter and Supply, installation, testing, and commissioning of Star-Delta Starter suitable for 150 HP, (Approx. 110 KW) 440V, 3-phase induction motor, complete all as specified and directed with all necessary accessories. The starter shall include the following components:1. Type: Fully Automatic Star-Delta Starter2. Motor Capacity: 150 HP3. Operating Voltage: 415 ±10% V, 50 Hz, 3 Phase AC Supply4. Enclosure: Dust and moisture proof, powder-coated MS enclosure with doorinterlock5. Protection:o Thermal overload relay (adjustable)o Single phasing preventiono Phase reversal protectiono Under-voltage protection6. Switchgear Components:o 3 Nos. Contactors (L&T / Siemens / Schneider / ABB make) suitable for 60HPo Timer for automatic star to delta changeovero Push button switches (Start, Stop, Reset)7. Indication Lamps: For ON, OFF, and Trip status8. Cable Entry: Bottom entry with proper gland and termination arrangement9. Mounting: Wall / Floor mounting type as per site requirement10. Standard Compliance: IS: 13947 (Part 1 & 4) or latest11. Make: L&T / Siemens / Schneider / ABB or equivalent approved makeWarranty: Minimum 1-year onsite warranty against manufacturing defects. |
| 8 | All as per item No .700 above but 60 hp (Approx 44 KW) complete all as specified and directed. |
| 9 | Supply and fix in replacement 3 Pole Power contactors type MNX with AC coil, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class insulation upto 170 Ampscomplete all as specified and directed. |
| 10 | All as per item No 9.00 above but 150 Amp complete all as specified and directed. |
| 11 | All as per item No 9.00 above but 30 Amp complete all as specified and directed. |
| 12 | S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 90-150 Amps including fixing arrangement complete all as specified and directed. |
| 13 | All as per item No 12.00 above but 9 to 15 Amps complete all as specified and directed. |
| 14 | Dismantling of defective submersible pump set 5 to 7.5 HP with column assembly, pump bowl assembly of any size/capacity including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts etc including re-fixing the same after making it serviceble in its existing position complete all as specified and directed. |
| 15 | All as per item No 14.00 above but pump set capacity 1 to 3 HP complete all as specified and directed.Note (i) Defective spares for pump and column assembly shall be measured and paid separately under respective item here-in-after. (ii) After taking out submersible pump set for repair the contractor shall cover tube will with cap to avoid any accident.(ii) Defective spare parts of bowl assembly shall be measured and paid separately under items here-in-after. |
| 16 | Supply only the Gun Metal Impeller parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 17 | Supply only the Gun Metal Impeller parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as specified and directed. |
| 18 | Supply only the Intermediate bowl parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 19 | Supply only the Intermediate bowl parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as specified and directed. |
| 20 | Supply only the Bowl bush rubber parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as specified and directed. |
| 21 | Supply only the Bowl bush rubber parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 22 | Supply only the Bowl bush (Gun metal) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 23 | Supply only the Bowl bush (Gun metal) parts of submersible pump bowl assembly suitable for 1 to 3HP complete all as specified and directed. |
| 24 | Supply only the Cast iron impeller seal ring (neck ring) parts of submersible pump bowl assembly suitable for 5 to 7.5 Hp complete all as specified and directed. |
| 25 | Supply only the Cast iron impeller seal ring (neck ring) parts of submersible pump bowl assembly suitable for 2 to 3 HP complete all as specified and directed. |
| 26 | Supply only the Stainless steel running sleeve (Off sizes) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 27 | Supply only the Stainless steel running sleeve (Off sizes) parts of submersible pump bowl assembly suitable for 01 to 3 HP complete all as specified and directed. |
| 28 | Supply only the Pump shaft parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 29 | Supply only the Pump shaft parts of submersible pump bowl assembly suitable for 1 to 3.0 HP complete all as specified and directed. |
| 30 | Supply only the CI Impeller parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as specified and directed. |
| 31 | Supply only the CI Impeller parts of submersible pump bowl assembly suitable for 1 to 3.0 HP complete all as specified and directed. |
| 32 | Dismantling of 01 to 03 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft etc including testing and refixing the same in existing position complete all as specified and directed.Note : Bush/bearing/sleeve/thrust plate shall be measured and paid separately under respective item here-in-after. |
| 33 | All as per item No 32.00 above but for 05 to 7.5 HP capacity complete all as specified and directed. |
| 34 | Supply only the Bush/bearing of suitable size (gun metal) suitable for 01-03 HP parts for the submersible motor complete all as specified and directed. |
| 35 | All as per item No 34.00 above but 05/7.5 HP complete all as specified and directed. |
| 36 | Supply only the Thrust Plate of suitable size (gun metal) suitable for 01-03 HP parts for the submersible motor complete all as specified and directed. |
| 37 | All as per item No 36.00 above but 5/7.5 HP complete all as specified and directed. |
| 38 | S&F in repairs submersible cable PVC insulated copper conductor 2.5 Sqmm 3 core 1100 volts grade complete all as specified and directed |
| 39 | All as per item No 38.00 above but 4 Sqmm complete all as specified and directed. |
| 40 | All as per item No 38.00 above but 6 Sqmm complete all as specified and directed. |
| 41 | M&L for 80mm bore, adopter nipple 50cm long GI flanged or socketed (for connecting column pipe to pump) complete all as specified and directed. |
| 42 | All as per item No 41.00 above but 100mm bore complete all as specified and directed. |
| 43 | M&L for coupler for pump and motor of any capacity (submersible pump) complete all as specified and directed . |
| 44 | M&L for motor housing studs of any size complete all as specified and directed. |
| 45 | S&F Cast iron non return valve of size 100 mm bore, ISI marked both ends flanged including rubber gasket, MS bolts, nuts, washers and tersting complete all as specified and directed. |
| 46 | All as per item No 45.00 above but 80 mm bore complete all as specified and directed. |
| 47 | Supply and packing pea gravel of 02 mm to to 06 mm size of the appoved quality as ordered to pack around the casing / slotted pipes in bore well complete all as specified and directed. |
| 48 | Developing tube wells by compressed air with minimum pressure of 10kg/Sqcm and minimum air discharge 450 CFM all as specified in IS 11189-1985 Para 4.3 complete all as specified and directed.Note : Compressor, pump, pipe and other allied items will be arranged by contractor and no extra payment will made by the department. |
| 49 | S&F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified and directed. |
| 50 | S&F MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA complete all as specified and directed. |
| 51 | S&F MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA complete all as specified and directed. |
| 52 | S&F in repair single phase preventor for protection for submersible pump against over loading, reverse phase, single phasing complete all as specified and directed. |
| 53 | Taking up centrifugal pump set from its foundation at different location of installations by disconnecting electrically and machnically, transporting it to the workshop for dismantling the pump sets and back to installation after repairing/removing of unserviceable parts complete all as specified and directed. |
| 54 | 150 HP Capacity |
| 55 | 60 HP Capacity |
| 56 | 10/12.5 Capacity |
| 57 | Upto 5 Hp Capacity |
| 58 | M & L for re-winding of electric motor of centrifugal pump sets 3 phase 415 volts 50 Hz AC with super enamelled copper winding wire of existing weight & size incl cleaning of stator slot winding paper fixing startor incl cut x size warnshing and baking complete all as specified and directed for capacity :- |
| 59 | 150 HP Capacity |
| 60 | 60 HP Capacity |
| 61 | 10/12.5 Capacity |
| 62 | Upto 5 Hp Capacity |
| 63 | Repairing of rotor assembly of centrifugal motor sets 3 phase 415 volts 50 Hz AC including dismantling and reassmbled at site complete all as specified and directed for capacity. |
| 64 | 150 HP Capacity |
| 65 | 60 HP Capacity |
| 66 | 10/12.5 Capacity |
| 67 | Upto 5 Hp Capacity |
| 68 | M&L painting of centrifugal pump set complete all as specified and directed including painting of SM No. and MES No. on the pump set for the capacity:- |
| 69 | 150 HP Capacity |
| 70 | 60 HP Capacity |
| 71 | 10/12.5 Capacity |
| 72 | Upto 5 Hp Capacity |
| 73 | Repairing/overhauling of centrifugal pump set incl cleaning of inside motor & pump set. Oiling greshing, gland packing filling and proper allignment incl repair/replacement of wear & tear are unserviceable part complete all as specified and directed for |
| 74 | 150 HP Capacity |
| 75 | 60 HP Capacity |
| 76 | Centrifugal pump set spare suitable for 150 HP pump set complete all as specified and directed |
| 77 | Ball bearing for motor of existing size |
| 78 | Ball bearing pump set of existing size |
| 79 | Roller bearing for pump set size |
| 80 | Impeller made out of existing size |
| 81 | Glands bush |
| 82 | Neck Ring |
| 83 | Cuppling complete of existing size |
| 84 | Pump shaft incl key |
| 85 | Rubber bush incl nut bolt and washer complete |
| 86 | Centrifugal pump set spare suitable for 60 HP pump set complete all as specified and directed |
| 87 | Ball bearing of motor of existing size |
| 88 | Ball bearing pump set of existing size |
| 89 | Roller bearing for pump set size |
| 90 | Impeller made out of existing size |
| 91 | Glands bush |
| 92 | Neck Ring |
| 93 | Cuppling complete of existing size |
| 94 | Pump shaft incl key |
| 95 | Rubber bush incl nut bolt and washer complete |
| 96 | Material and labour for column pipe GI 'C' class for borewell 2\\" dia including threading and all connected works complete all as specified and directedNote : Taking up of motor and lowering will be measured seperately. |
| 97 | Material and labour for column pipe GI 'C' class for borewell 3\\" dia including threading and all connected works complete all as specified and directed.Note : Taking up of motor and lowering will be measured seperately. |
| 98 | Taking out and dismantling of defective jockey pump set of 12.5 HP (Cap 10.8 cum / Hr Cap) with column assembly, pump bowl assembly, Gun metal Impeller, Intermediate Bowl, CI Impeller (Neck Ring), Bowl Bush Rubber/Gun Metal, etc Parts, including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts and other defected parts etc including re-fixing the same after making it serviceble in its existing position complete all as specified and directed. |
| 99 | M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm size, buried directly in ground (earth pit not less than 3.25M deep below normal ground level) with top edge of the plate not less than 1.5M below normal ground level connected to and including galvanized steel earth strip 32 x 6mm, including 40mm bore GI light grade protection pipe as earth lead strip connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150mm thick alternate layers of charcoal or cock dust & common salt 20mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) cover 50mm thick of precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) duly reinforced with 8mm deformed or twisted bars @ 100mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/loose soil and deposited the surplus soil to a distance n.exc 50mtr away from starting point complete all as specified and shown in electrical plate No 3 of MES standard schedule of rates 2009 Part-I complete all as specified and directed. |
| 100 | Supply and fixing UPVC column pipe 80 mm bore 12 Kg working pressure standard grade for pump set including plastic rope for supporting of submersible motor necessary fitting and connection to submersible pump complete all as specified and directed. |
| 101 | All as per item No. 64.00 above but 100 mm bore complete all as specified and directed. |
| 102 | All as per item No. 64.00 above but 50 mm bore complete all as specified and directed. |
| 103 | Supply and fixing plastic rope 25 mm for supporting of submersible motor with necessary fitting and connection to submersible pump complete all as specified and directed. |
| 104 | Supply and fixing plastic rope10 mm for supporting of submersible motor with necessary fitting and connection to submersible pump complete all as specified and directed. |
| 105 | Servicing of Motorised Butterfly Valve - size 100mm /150mm i.e. removing, cleaning, greasing, checking for wear and tear, refixing, testing, installing, commissioning as directed.Note : Spares if needed are not included in the above |
| 106 | Supply & fix in repair/replacement of Single Phasing Preventer complete all as specified and directed. Model :VSP D2Make - Minilec/HAVELLS/SCHNEIDER |
| 107 | Supply & fix in repair/replacement of Relay with base - 4 C/O, 240V/24V DC complete all as specified and directed.Make : LEONE / IDEC/OMRON |
| 108 | Supply only in repair/replacement of LED Indicators of Colour : Red / Yellow / Green /Blue complete all as specified and directed.Make : ESBEE / TEKNIC/SCHNEIDER |
| 109 | Supply only in repair/replacement of Push Button with LED Indicator – 240V A.C. Colour : Red / Yellow / Green complete all as specified and directed.Make: TEKNIC/SCHNEIDER/ESBEE |
| 110 | Supply only in repair/replacement ofselector switch 2 way, 3 way with NO, NC contact complete all as specified and directed. Make: TEKNIC/SCHNEIDER/ESBEE |
| 111 | Supply only in repair/replacement only NO Contact /NC contact- 240V A.C.,3 A complete all as specified and directed. Make: TEKNIC/SCHNEIDER/ESBEE |
| 112 | Supply only in repair/ replacement SMPS Input Voltage: 230 V, Output Voltage: 24 V, 5A complete all as specified and directed. Make: NHP/SCHNEIDER/MINWELL |
| 113 | Supply only in repair/ replacement Programmable Logic Controller with 40 input and 40 output complete all as specified and directed. Make: Unitronics / Mitsubishi/ALLEN BRADLEY/ SIEMENS |
| 114 | Supply only in repair/ replacement I/O Module complete all as specified and directed. Make: Unitronics / Mitsubishi/ALLEN BRADLEY/ SIEMENS |
| 115 | Supply only in repair/ replacement Human Machine Interface (HMI) 7 inch color 24 v DC power supply complete all as specified and directed. Make: Unitronics / Mitsubishi/ALLEN BRADLEY/ SIEMENS |
| 116 | Supply only in repair/ replacement of Antenna with 9DB gain for wireless communication complete all as specified and directed. |
| 117 | Supply only in repair/ replacement of communication Chord for connectivity between PLC and Wireless Modem complete all as specified and directed. |
| 118 | Supply and fix repair/replacement of MCB 4P,10 A complete all as specified and directed. Make: TELEMECHANIQUE/ HAVELLS |
| 119 | Supply and fix in repair/replacement of Limit Switch for Actuator suitable for upto 300 mm dia. Butterfly Valve complete all as specified and directed. Make: Honeywell/Siemens/Cherry |
| 120 | Supply and fix in repair/replacement of buzzer 24V DC for PLC control Panel complete all as specified and directed.. Make: MIMIC/L&T/Siemens |
| 121 | Rewiring of the existing PLC control panel with 0.5 sq.mm copper flexible FRLS cable with proper ferruling and Lugs complete all as specified and directed.Make: Polycab/Primecab/Finolex/FSC |
| 122 | Programming and communication set-up between SCADA and PLC control panel through GPRS communication as Master-slave communication for monitoring and operation of all the pumps, valves and water levels complete all as specified and directed. |
| 123 | Supply and fix in repair/replacement of Capacitor & resistance set for Actuator suitable for 100/150/300 mm dia. Butterfly Valve complete all as specified and directed. |
| 124 | Supply only in repair/ replacement of wireless modem Make: Mastro heritage/ LEO/M-COM Technologies complete all as specified and directed. |
| 125 | Supply, Installation, Testing and commissioning of Flow/Pressure Switch 1-10KG/sq.cm with Pressure Guage nad necessary fittings with proper wiring as directed.Make: INDFOSS/DANFOSS/RAPID CONTROL |
| 126 | Supply, Installation, Testing and commissioning of Air releasing solenoid valve having 10mm dia, 230 V AC operated coil complete all as specified and directed. Make:- ROTEX/AVCON/JOHNSON CONTROLS/ASCO |
| 127 | Supply, Installation, Testing and commissioning of Priming solenoid valve/ Actuator having 25mm dia, 230 V AC operated coil complete all as specified and directed, Make:- ROTEX/AVCON/JOHNSON CONTROLS/ASCO |
| 128 | Supply, Installation, Testing and commissioning of motor actuated butterfly valve with the following specifications including all accessories (CI fittings required at site) complete all as specified and directed. (a) Valve size 200mm dia. (b) Designed line pressure 6 kg/Sqcm(c) Operating Angle : 90 degrees(d) Disc material CI with nylon coating(e) Limit switches : 02 Nos for open and close(f) Mounting : Splash proof-Direct on valve/ Extended type as per site requirement.(g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication(i) Valve position indication with an output of 4-20m A(j) The actuator should be capable of accepting 4-20m A of input of regulating purposes (k) Mannual Operation : Hand Wheel/Rapid ControlMake : ROTORK/S M INSTRUMENTATION/ EMTORK/ HASSEL HOFFNER/ S D TORQUE/ AUMA |
| 129 | Supply, Installing,Testing and Commissioning of Ultrasonic Level Transmitter complete all as specified and directed. Range : 0-5 metres Accuracy : 0.5 % minimum Supply Voltage : 24V dc Output : 4-20 mA Ultrasonic Frequency:75 kHz burst, rep. rate 96 msDelay at Power-up: 1.5 secondsTemperature Effect: Uncompensated: 0.2% of distance/°C &Compensated: 0.02% of distance/°CDelay at Power-up: 1.5 secondsResolution: 1.0 mmOutput Response Time: 100 ms to 2300 msMinimum Window Size: 20 mmEnvironmental Rating: Leakproof design is rated IEC IP67; NEMA 6POperating Conditions: Temperature: –20 °C to 70 °C (–4 °F to 158 °F)Maximum relative humidity: 100% Make:Endress +Houser/ SIEMENS/ HONEYWELL/ BANNER/ SBEM/ KROHNE MARSHALL |
| 130 | Supply & fixing in replacement 6 core, 1.5 sqmm cross sectional area armoured copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc complete all as specified and directed. Make: Polycab/FSC/Torrent/Finolex |
| 131 | Supply & fixing in replacement 4 core, 1.5 sqmm cross sectional area copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc complete all as specified and directed. Make: Polycab/FSC/Torrent/Finolex |
| 132 | Supply & fixing in replacement 2 core, 1.5 sqmm cross sectional area copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVC sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc complete all as specified and directed. Make: Polycab/FSC/Torrent/Finolex |
| 133 | Supply, Installation, Testing and commissioning of Flow/Pressure Switch 1-10KG/sq.cm with Pressure Guage nad necessary fittings with proper wiring as directed.Make: INDFOSS/DANFOSS/RAPID CONTROL |
| 134 | Supply, Installation, Testing and commissioning of Air releasing solenoid valve having 10mm dia, 230 V AC operated coil complete all as specified and directed. Make:- ROTEX/AVCON/JOHNSON CONTROLS/ASCO |
| 135 | Supply, Installation, Testing and commissioning of Priming solenoid valve/ Actuator having 25mm dia, 230 V AC operated coil complete all as specified and directed. Make:- ROTEX/AVCON/JOHNSON CONTROLS/ASCO |
| 136 | S&F in repair Openwell Submersible Pump 1 HP, Single Phase, 210 Volts, Size 25mm X 25mm with Control Panel complete all as specified and directed. |
| 137 | S&F in repair Openwell Submersible Pump 3 HP, Three Phase, 210 Volts, Size 25mm X 25mm with Control Panel complete all as specified and directed. |
| 138 | S&F in repair Openwell Submersible Pump 5 HP, Three Phase, 210 Volts, Size 25mm X 25mm with Control Panel complete all as specified and directed. Please Enable Macros to View BoQ information |
| 139 | S&F in repair Openwell Submersible Pump 5 HP, Three Phase, 210 Volts, Size 25mm X 25mm with Control Panel complete all as specified and directed. Please Enable Macros to View BoQ information |
