Tender For Survey, Soil Investigation, Design, Supply Of All Materials, Labour, T&P Etc. Required For Construction, Erection, Completion, Testing & Commissioning Of Water Supply Works Such As Reinforced Cement Concrete Ohts, Tubewells, Zpss/Cwr Cum P, Fatehabad-Uttar Pradesh

TDR : 54803704

Tender Notice
BOQ

26 Days Left

Fatehabad , Uttar Pradesh

Tender Brief : Tender For Survey, Soil Investigation, Design, Supply Of All Materials, Labour, T&P Etc. Required For Construction, Erection, Completion, Testing & Commissioning Of Water Supply Works Such As Reinforced Cement Concrete Ohts, Tubewells, Zpss/Cwr Cum P

Document Fees
₹ 23600 /-

EMD
₹ 2975000.0 /-

Tender Value
Refer document

Submission Date
20-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Design, Supply of all materials, labour, T&P etc required for construction of Intz type RCC Over Head Tank including various works like - Ventilator and Water level indicator, Lightening conductor, C.I. D/F Verticle pipes (Inlet Pipe, Outlet Pipe, Overflow Pipe & Washout Pipe), duck foot bend, puddle collers and bell mouths, Sluice valve on inlet, outlet & washout pipe and Valve Chamber, Bye-pass arrangement of OHT, Flooring with Apran & Drain( min.100 mm thick PCC of 1:2:4 & 100 mm thick RCC of 1:1.5:3 with nominal reinforcement), Floor level shall be 60 cm above the finished ground level of Campus, Three coat apex painting over one coat primer of approved colour after finishing of RCC surface with grinder, repair of pin holes, unevenness., Railings - G.I. Pipe railing around stair case (both sides), balcony & top dome periphery, S.S ladder from opening of top dome to bottom dome, Stair case (Seperate two column based RCC staircase and 1 m wide balcony with arrangement of M.S Gate and Jali for 600 KL OHT & 1.0 m wide stair case around OHT column for 250 kl OHT), Food grade epoxy coating of FOSROC / Ciba-Geigy or reputated brand on inside surface area of water container after testing for water tightness, of capacity and staging mentioned as under:For bidding purpose, bearing capacity of soil shall be considered as 8t/sq.m. Working design shall be based on the SBC determind after soil investigation / 8 tonne/sqm.Note :- The bid price of Over Head Tanks is to be submitted considering net safe allowable bearing capacity as 8 t/m2, keeping the minimum foundation depth to be 2.5 m below existing ground level at the site of work. The successful bidder will be required to investigate the soil bearing capacity. If net safe allowable bearing capacity is found to be equivalent or more than 8 t/m2, the design of OHT will be based on 8 t/m2 capacity. However, in case the net safe allowable bearing capacity is found to be below 8 t/m2, then the design of OHT will be based on the actual bearing capacity.
2	1450 KL OHT At Zone-I Shivaji Nagar
3	1150 KL OHT At Zone-II Purani Galla Mandi
4	Design, supply of all material, labour, T&P etc. required for construction of Ractangular, R.C.C Clear Water Reservoir cum pump house including various works like 1 m wide stair case with stainless steel hand railing to go inside reservoir, sump below the pump house area, stainless steel railing over the R.C.C slab of reservoir, Granular texture finish on exterior surface of pump house, gantry beam, food grade epoxy coating of FOSROC / Ciba-Geigy or reputated brand on inside surface area of water container after testing for water tightness, of capacity mentioned as under:Note : The bid prices of Clear Water Reservoir / Pumping Stations are to be submitted considering the depth of excavation may extend up to 6 m BGL.
5	375 KL CWR At Zone-I Shivaji Nagar
6	350 KL OHT At Zone-II Purani Galla Mandi
7	Construction of Meter Room as per type design (Size - 4m x 4m x 4m) including supply of all materials, labour, T&P etc. required for proper completion of the work as per the directions of Engineer-in- charge.
8	Construction of Panel Room as per type design (Size - 5m x 5m x 4 m) including supply of all materials, labour, T&P etc. required for proper completion of the work as per the directions of Engineer-in- charge.
9	Construction of Chlorinating Room as per type design (Size - 6m x 4m x 4 m) including supply of all materials, labour, T&P etc. required for proper completion of the work as per the directions of Engineer-in- charge.
10	Construction of SCADA Control Room as per type design (Size - 10m x 4m x 4 m) including supply of all materials, labour, T&P etc. required for proper completion of the work as per the directions of Engineer-in- charge.
11	Supply of ISI mark DI K-9 and K-7 S&S pipes (push on joints) of following class and diameters inclusive of jointing material (Rubber gasket of EPDM Quality, Bend, Tee etc.) including all statutary duties and taxes, third party inspection charges, transit insurance, freight, transportation to store/ site of work, unloading, stacking etc. complete as directed by Engineer –in-charge.
12	D.I. Pipe Class-K9
13	250mm dia
14	200mm dia
15	150mm dia
16	125mm dia
17	100mm dia
18	D.I. Pipe Class-K7
19	400mm dia
20	350mm dia
21	300mm dia
22	250mm dia
23	200mm dia
24	Supply of High Density Polyethelene Pipes (HDPE (PN-6)/PE-100), conforming to IS 4984 / 14151 / 12786 / 13488 in coils/ standard lengths with nesessary jointing material like electro-fusion coupler, electro-fusion Tee, electro-fusion band, electro-fusion reducer, flanged joint, including all statutary duties and taxes, third party inspection charges, transit insurance, freight, transportation to store/ site of work, unloading & stacking the same in covered shade duly protecting from sunrays & rains, etc. complete as directed by Engineer –in-charge.
25	110 mm (HDPE (PN-6)/PE-100)
26	140 mm (HDPE (PN-6)/PE-100)
27	160 mm (HDPE (PN-6)/PE-100)
28	Earth work in excavation for pipeline trenches in following type of soils with lead upto 50M, refilling the soil as required, including depositing in layers not exceeding 150mm, watering and compaction to 95% of the Standard Proctor density, level dressing, including supply of all labour, T&P etc. required for proper completion of the work.
29	In ordinary soil
30	0 - 1.5
31	Carting, lowering, laying and jointing with SBR ruber gaskets D.I. K-7/ D.I. K-9 pipes of following dia & pressure including all specials, to site of work, lowering them into trenches, laying true to alignment and gradient, in proper position, cutting of pipes, making of joints including cost of jointing materials and rubber rings, labour, T&P, including hydraulic testing etc. complete as directed by Engineer in-charge. It includes provision for making of alignment on city roads, making trial pits to investigate location of various under grounds services like telephone cables, electric cable, existing pipe lines and sewer lines etc. arrangements for diversion of traffic and associated works etc. with supply of all necessary equipment, materials, labour and T&P etc. complete required for completion of work. The trenches shall be properly barricaded and fenced off wherever necessary. Red flags and caution boards during day and red lights during night shall be displayed so as to avoid any accidents. Note : Only SBR Rubber gaskets to be used as per IS-5382 and IS- 12820.
32	D.I. Pipe Class-K9/K7
33	400mm dia
34	350mm dia
35	300mm dia
36	250mm dia
37	200mm dia
38	150mm dia
39	125mm dia
40	100mm dia
41	Carting, lowering, laying of following dia of HDPE Pipe (PN-6)/PE-100 of following dia and requisite specials to site of work, lowering them into trenches, laying true to alignment and gradient, in proper position, cutting of pipes, making of joints including cost of jointing materials and rubber rings, labour, T&P, including hydraulic testing etc. complete as directed by Engineer in-charge. It includes provision for making of alignment on city roads, making trial pits to investigate location of various under grounds services like telephone cables, electric cable, existing pipe lines and sewer lines etc. arrangements for diversion of traffic and associated works etc. with supply of all necessary equipment, materials, labour and T&P etc. complete required for completion of work.The trenches shall be properly barricaded and fenced off wherever necessary. Red flags and caution boards during day and red lights during night shall be displayed so as to avoid any accidents. Note: Jointing between HDPE pipes and specials shall be done as per the latest IS: 7634 part II. Only Bar coded electro-fusion machine (Automatically Readable) that can read the bar code of the fittings automatically shall be used for jointing of HDPE pipe/fittings.
42	110 mm (HDPE (PN-6)/PE-100)
43	140 mm (HDPE (PN-6)/PE-100)
44	160 mm (HDPE (PN-6)/PE-100)
45	Supply of following types of D.I. valves confirming to the I.S. specification inclusive cost of jointing materials (Rubber gasket of EPDM Quality, dismantling joint or mechanical joint, Nut & Bolts etc.) including all statutary duties and taxes, third party inspection charges, transit insurance, freight, transportation to store/ site of work, unloading, stacking etc. complete as directed by Engineer –in-charge.
46	Manually Operated DI D/F Sluice valve, PN 1.6 as per IS 14840 : 2000
47	100 mm
48	125 mm
49	150 mm
50	200 mm
51	250 mm
52	300 mm
53	350 mm
54	100mm dia for Scour valve
55	Air valves as per IS 14845 : 2000 including Sluice valve of Isolation
56	50 mm
57	Fire Hydrant as per IS Code 908 : 1975
58	80 mm
59	Carting, lowering, laying, aligning, fixing in position and installation of following valves in pipe line including all material, labour, testing and commissioning as per direction of Engineer-in- charge.
60	Double flanged Ductile Iron Sluice valves as per IS 14840 : 2000
61	100 mm
62	125 mm
63	150 mm
64	200 mm
65	250 mm
66	300 mm
67	350 mm
68	100mm dia for Scour valve
69	Air valves as per IS 14845 : 2000
70	50mm to 80 mm dia
71	Fire Hydrant as per IS Code 908 : 1975
72	80 mm dia
73	Supply of all materials, labour, T&P etc required for construction of brick masnory chambers for valves mentioned below. It includes excavation, 100 mm thick PCC, brick work in 1:6, 12 mm thick plaster in 1:4 and precast RCC (M20 grade) slab of thickness 200 mm as per the directions of Engineer-in- charge.
74	Sluice valve Chamber
75	100mm to 250 mm (Size-1.3mx1.4mx1.625m)
76	300mm dia to 400 mm dia (Size-1.5m x 1.7m x 2.1m
77	Air Valve Chamber (Size-0.8m x 0.8m x 0.8m)
78	Scour Valve Chamber (Size-1.3m x 1.4m x 1.625m)
79	Fire Hydrant Chamber
80	Dismantling of following type of road surfaces for laying of pipe line and house connection work including sorting out of serviceable materials and disposal of unserviceable materials including supply of all materials, labour, T&P etc. required for proper completion of the work.The rates of dismantling of roads as mentioned below for different types of roads include the cutting of existing thickness of road either single or multiple layer of roads. No extra payment shall be made to the contractor for cutting multiple layers of roads.
81	Bituminious Road
82	Cement Concrete Road
83	Interlocking Tiles Road
84	Re-instatement of following type of road surfaces after laying of pipe line and house connection work including supply of all materials, T&P etc. requuired for proper completion of the work as per direction of engineer-in-charge. The quantity of re-instatement has been increased by thirty percent in the view of additional damaged of dismantled road due to traffic / vehicle movement.
85	Bitumen roadTYPE AConstruction of bitumen road as per UPPWD specification including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-GSB G-1 (One coat) (90-40 mm) = 12.5 cmG -2 (one coat) (45-63 mm) = 7.5 cmG - 3 (one coat) (22.5 - 53 mm) = 7.5 cmBM (One coat) = 7.5 cmSDBC (One coat) = 2.5 cm
86	TYPE BConstruction of bitumen road as per UPPWD specification including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-Bitumen Road (SDBC + Tack coat)SDBC (One coat) = 2.5 cmTack coat with bituminous emulsion (MS) = 0.25 kg/sqm(30% consider for over dismantling of existing road)
87	Cement Concrete RoadConstruction of Cement Concrete road including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-PCC = 100 mm,1:3:6 (cement, coarse sand & stone ballast of 20-40 mm) CC =100 mm, 1:1.5 :3 (cement, coarse sand & stone ballast of 16-20 mm)
88	C.C. Interlocking Tiles Road Type AConstruction of 80 mm tihck C.C. Interlocking Tile road including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-PCC = 100 mm,1:4:8 (cement, coarse sand & stone ballast of 20-40 mm)Sand = 30mm to 50mm thick local sand lair for preparation of surfaceTiles = 50% new + 50% old
89	Providing and laying in position reinforced cement concrete (mix 1:2:4) for construction of thurst block at bends of feeder main, rising main & distribution system including batching, mixing, placing, vibrating, curing, formwork, finishing, including cost of all material and labor, tools and plants required with transportation, loading, unloading, etc., complete for all leads and lifts etc required for proper completion of the work.
90	Providing H.Y.S.D steel reinforcement for reinforced cement concrete work including straightening, cutting, bending, hooking, placing in position, lapping and/ or welding wherever required, tying with binding wire and anchoring to the adjoining member wherever necessary as per design, including cost of materials and labor complete as per drawings.
91	Disposal of surplus earth /unserviceable material, by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.
92	Repairing / Shifting of existing water supply house connection due to falling in alignment of pipe line including supply of all materials, labour, T&P etc. required for proper completion of the work.
93	Provision for crossing of Nalas for laying of pipe line using HDPE casing pipe of suitable dia. and length including labour, T&P, necessary arrangement for diversion & pumping of water if required, barricading etc required for proper completion of work as per directions of engineer-in-charge.
94	0.3 - 0.5 m (Clear span)
95	0.5 - 1.0 m (Clear span)
96	1.0 - 1.5 m (Clear span)
97	1.5 - 2.0 m (Clear span)
98	Repairing of drain/ public ramp/other miscellaneous structures which are coming in alignment of pipe line and damaged during the laying of pipe line including supply of all materials, labour, T&P etc. required for proper completion of the work.
99	Brick masonry in cement mortar 1:4
100	12mm thick plaster in cement mortar 1:4
101	RCC M-20 (including MS work)
102	Providing and making water supply house connection from distribution pipe line of following diameters using 20 mm dia pipe (HDPE pipe (PE 100/ PN 12.5) below ground and medium class GI pipe above ground), saddle (electro-fusion tapping saddle for making connection with HDPE distribution pipeline, DI strap saddle, ferrule, for making connection with distribution pipeline other than HDPE), compression fittings (FTA, MTA etc.), ball valve, specials, including supply of all materials, labour, T&P etc. required for proper completion of the work. It also includes excavation, refilling of pit required for making house connection.
103	For 110 mm dia
104	For 125 mm to 160 mm dia
105	For 180 mm to 200 mm dia
106	For 250 mm to 350 mm dia
107	Construction of compound wall comprising of RCC Columns @ 3.0m c/c distance with beam at plinth and top, brick work in 1:4 of as per type design including supply of all material, labour, T& P etc complete.
108	Supply and fixing 3.60 m wide MS main gate & 1.0 m wide a wicket gate with RCC Columns as per type design & drawing including primer and painting, meterial, labour, T&P etc all complete.
109	Providing and laying in position reinforced cement concrete (mix 1:2:4) for construction of drain, size 250 mm x 250 mm, over PCC 1:4:8, including batching, mixing, placing, vibrating, curing, formwork, finishing, including cost of all material and labor, tools and plants required with transportation, steel, loading, unloading, etc., complete for all leads and lifts and as per specifications etc required for proper completion of the work.
110	Construction of following types of Road/ flooring for development of CWR / OHT campus required as per site condition
111	C.C. Interlocking Tiles Road Construction of C.C. Interlocking Tile road including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-PCC = 100 mm,1:4:8 (cement, coarse sand & stone ballast of 20-40 mm)Sand = 50 mm thick local sand lair for preparation of surfaceTiles = 100% new Note : 100 mm thick rubber moulded interlocking tile shall be used for construction of interlocking tile road.
112	Construction of Pump house of Size -3.60M x 3.0M x 3.0M (RCC Frame Structure) including supply of all materials, labour, T&P etc required proper completion of work as per type design.
113	Construction of Pump house of Size -3.60M x 3.0M x 3.0M cum Chlorinating Room of Size-1.8M x 2.5M x 3.0M (RCC Frame Structure) including supply of all materials, labour, T&P etc required proper completion of work as per type design.
114	RAIN WATER HARVESTING AND GROUND WATER RECHARGING.
115	Sand filling in trench at crossing of major road including supply of necessary quantity of sand from a distance not exceeding 10 km. From the site of work and including watering, dressing etc. Rate to include the cost of all materials. Labour, t & p etc. Required for proper completion of the work.
116	E&M Works
117	Zone-1 (New Tubewells)
118	Drilling of borehole for Tubewell contruction by RC Rig Machine including transportation, erection, dismantling of Rig and assoiated T & P complete in all respect including required all material, labour etc.
119	Transportation, Erection and Dismantling of Rig Machine
120	Drilling of 500mm size bore from
121	(i) 0M BGL to 100MBGL
122	(ii) 100M BGL to 140MBGL
123	Zone testing in water quality problem areas including all required material, labour, T&P etc. complete in all respect.
124	Tubewell AssemblyM.S. tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) rings, well cap, bail plug, clamp, reducer, central guide, support structer etc. as required & as per typed design complete in all respect.
125	200 mm. Dia MS ERW Housing/ casing/ Slotted pipe having wall thickness of 7.1mm.
126	Supply of pea gravel
127	Logging of bore hole by departmental / approved electric logger.
128	Lowering of Tube well assembly duly welded including welding electrode and shurounding of pea gravel complete in all respect.
129	Lowering of 200mm dia pipe from 0 to 100m deep BGL.
130	Lowering of 200mm dia pipe from 100 to 130m deep BGL.
131	Development of Tubewell by compressor
132	Transportation, Installation and Dismantling of Air Compressor
133	Development of Tubewell by 250 PSI or requisite Capacity of Air compressor
134	Development of Tubewell by O.P. Unit
135	Transportation, Installation and Dismantling of O.P. Unit & Yield Test.
136	Development of Tubewell by 3 Cusec or requisite Capacity of O.P. Unit
137	Chemical and Bacterological test of water sample from depaprtmental/ approved lab.
138	Provision of failed attempt of tubewell construction due to various reasons such as poor strata, less aquifer volume, quality problem area or any other issue whatsoever encountered during work execution.
139	PUMPING PLANT OVER NEW TUBEWELL NO.-7 IN ZONE-1
140	SITC of Submersible pumpset (450 LPM discharge 84 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer, Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
141	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
142	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
143	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
144	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
145	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
146	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
147	PUMPING PLANT OVER NEW TUBEWELL NO.-8 IN ZONE-1
148	SITC of Submersible pumpset (450 LPM discharge 87 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
149	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
150	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
151	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
152	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
153	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
154	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
155	PUMPING PLANT OVER NEW TUBEWELL NO.-9 IN ZONE-1
156	SITC of Submersible pumpset (450 LPM discharge 88 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
157	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
158	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
159	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
160	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
161	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
162	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
163	PUMPING PLANT OVER TUBEWELL NO.-10 IN ZONE-1
164	SITC of Submersible pumpset (450 LPM discharge 92 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
165	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
166	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
167	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
168	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
169	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
170	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
171	PUMPING PLANT OVER TUBEWELL NO.-11 IN ZONE-1
172	SITC of Submersible pumpset (450 LPM discharge 91 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
173	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
174	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
175	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
176	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
177	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
178	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
179	PUMPING PLANT OVER NEW TUBEWELL NO.-12 IN ZONE-1
180	SITC of Submersible pumpset (450 LPM discharge 79 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
181	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
182	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
183	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
184	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
185	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
186	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
187	PUMPING PLANT OVER NEW TUBEWELL NO.-13 IN ZONE-1
188	SITC of Submersible pumpset (450 LPM discharge 111 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
189	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
190	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
191	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
192	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
193	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
194	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
195	SITC of Automatic type chlorinating plant solenoid driven dosing pump of capacity 0-6 LPH ( pressure 4kg/cm2 with ORP sensor to check and regulate the dosing along with 200 ltr capacity HDPE tank (02 nos., 1W+1S) ,standard fittings, wall/floor mountings MS bracket for dosing pump with GM Valve ,cock valve & sodium hydro chloride solution.,chlorine test kit with O.T. Solution complete with all respect.( suitable for 100-220V and 30-60 Hz , suction lift- 1.5 m., injection pressure 4 bars, steadt state accuracy +-3% repeatability +-3%) with RS 485 Port O/P having facility of interface with PLC SCADA system. ( As this tubewell feeds OHT directly)
196	PUMPING PLANT OVER NEW TUBEWELL NO.-14 IN ZONE-1
197	SITC of Submersible pumpset (450 LPM discharge 110 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
198	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
199	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
200	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
201	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
202	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
203	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
204	SITC of Automatic type chlorinating plant solenoid driven dosing pump of capacity 0-6 LPH ( pressure 4kg/cm2 with ORP sensor to check and regulate the dosing along with 200 ltr capacity HDPE tank (02 nos., 1W+1S) ,standard fittings, wall/floor mountings MS bracket for dosing pump with GM Valve ,cock valve & sodium hydro chloride solution.,chlorine test kit with O.T. Solution complete with all respect.( suitable for 100-220V and 30-60 Hz , suction lift- 1.5 m., injection pressure 4 bars, steadt state accuracy +-3% repeatability +-3%) with RS 485 Port O/P having facility of interface with PLC SCADA system. ( As this tubewell feeds OHT directly)
205	PUMPING PLANTS & ELECTRIC SUBSTATION IN PROSPECTIVE TO C.W.R., ZONE-1
206	PumpSet at C.W.R:
207	Supply of Clearwater Botton -Suction Submersible Pumpset having Speed 2900 RPM coupled with suitable KW rating of Electric motor compatible for handling Clear Water with Automatic Coupling Pumpset accessories etc. complete in all respect and also having following parameters:-(a) Capacity 2450 LPM(b)Total head 50 Mtrs.(c) Delivery size suitable(d) Material of Construction-:(i) Casing- CI IS210 FG260(ii) Impeller - CF8M, BHN 180 approx(ii) Shaft - SS 410 (iii) Bearing- anti frictional (e) Operational Voltage 380±10% 3 phase AC Supply. (f) Pumpset accessories such as duck foot bend, pedestal auto coupling with guidepipe only in S.S. for pump set. Total nos. of 02 Pumpsets are proposed in module of operation in 01 nos. are working , 01 Pump is standby . (NOTE- Pump Discharge, Head & motor HP are tentative and may vary as per actual site condition at the time of execution.)
208	Cast iron pipes & specials.
209	Supply of galvanized nut- Bolt SS-304 and rubber packing material for erection of above.
210	Reflex Valve
211	CIDF double flanged single/multi door swing check valves PN 1.0 FG200 Grade having body comprising inlet & outlet sheets in gradeed cast iron diaphragm fitted woth st. steel, faces,diaphragm plate and door , sub pins and shall be of following sizes:
212	200 mm dia
213	250 mm dia
214	CI Dismantling joints
215	200 mm dia
216	250 mm dia
217	E.O.T. Monorail Travelling trolley with chain pulley block.
218	E.O.T. Monorail Travelling Trolley with spur gear of 3.0 tonne capacity with chain pulley block with suitable lift and span as per approved Structural GAD of pumping station.
219	Automatic type Chlorinating Plant
220	SITC of SCADA Compatible Automatic type chlorinating plant solenoid driven dosing pump of capacity 0-20 LPH or suitable capacity, pressure 4kg/cm2 with ORP sensor to check and regulate the dosing along with 500 ltr capacity HDPE tank ,standard fittings, wall/floor mountings MS bracket for dosing pump with GM Valve ,cock valve & sodium hydro chloride solution 40 ltrs.,chlorine test kit with O.T. Solution complete with all respect.( suitable for 100-220V and 30-60 Hz , suction lift- 1.5 m., injection pressure 4 bars, steadt state accuracy +-3% repeatability +-3%).
221	L.T. Panel Board suitable for operation on 400 V, 3 Phase 50 Hz. A.C. supply in sheet steel enclosure in cubical pattern floor mounting with following fitted on the phase of the panel with bus incomer bar of 320 amps. Capacity, Aluminium Bus Bar size of 40*10 mm. and neutral of half the capacity sectionalized through a bus section. The panel shall comprise of the following. 02 No. incoming feeder from 01 Nos. LT feeder & 01 Nos. spare for future use with following details:-02 nos. MCCB of 250 amps,50 KA Micro processor type for Two incomer preferably schneider/ABB with indication lamp mechanical on/off indicator.One set of current transformer of ratio 300/5AOne No. CT operated ammeter 0-300A with ammeter One No. Voltmeter 0-500 V with voltmeter One No power factor meter 0.5 lag/ 1-0.5 lead One No Surge arrestor Relay & One no. UV/OV RelayOne No frequency meter.Total Nos. of Outgoing feeder as follows-MCCB of 125 amps,50KA capacity with indication lamp mechanical on/off indicator. -02 nos.Ammeter with selector switch.Single phasing preventer. Sets of timer and relays for overload and underload. 01 Nos. 63 Amps. MCCB for RTU/PLC Panel.01 Nos. 63 Amps. MCCB as Misc. load02 Nos. 32 Amps. 4P MCCB for lighting & spare one.
222	Supply of 01 No. required rating of APFC Panel with capacitor bank and feeder SFU & MCCB 63 Amp., 25 KA with APFC relay & other acceessories to adjust automatically the power factor close to upf.
223	Power and control cables
224	1100 V grade, 3.5 core x 35 mm2 PVC insulated PVC sheathed Aluminium Armoured conductor cable from LT panel to starters.(1x2x75 mtr.)
225	1100V grade, 2x3C x25 mm2 PVC insulated PVC sheathed submersible copper flat cable to motor 3 Nos pumps. (2x2x25 mtr.)
226	Control cable 1x10C, 1.5 mm2 PVC insulated PVC sheathed Copper conductor cable for moisture sensor Reverse protection thermistor relay etc.
227	EARTHING
228	Complete earthing of all the equipments as detailed above shall be done as per IS/IER/PWD specification with G.I Plates, watering pipe and loop earthing with adequate size of G.I/ Al. strip etc. (PS-702) Each of the equipment (Pumps + LT Panel + PLC Panel.) size of earthing plate 600mm x 600mm x6 mm with salt and coal.
229	Lighting system:
230	Supply & erection of M.S. Tubular Poles SP-36, 9.5 M height.
231	S/F of 72 watt LED with lumen reflector.
232	Feeder pillar for lighting
233	Supply and laying of 4x16mm2 Al. armoured cable.
234	Internal electrification with fixtures.
235	S/F 1200 mm ceiling Fan for LT Room
236	S/F of exhaust Fan for LT Room.
237	Earthing of street light pole
238	Painting of street light (P5-634)
239	Supply and installation of DCP type of 5 Kg. Fire existinguisher (PS-1132)
240	12 mm thick rubber mating for safe working on.
241	Tools and Spanners:
242	Hydrulic crimping tools- Crimping range: 16-300 sq.mm.,Weight: 6 Kg. ,Length: 500mm
243	Mannual crimping tools- Crimping range: 400 sq.mm.
244	Tong tester (AC/DC-1000A) Multimeter (AC/DC-1000A) Megger (AC/DC-500V) Screwdriver (6\\"x 12\\") Plier (250mm)
245	Chain wrench (12\\"x18\\"), Pipe wrench (1200mm)
246	Chequered plate of required size so as to cover all trenches.
247	Erection or Installation with earthing of All above equipments complete in all respect.
248	Testing of All above equipments etc. complete in all respect.
249	Commissioning of All above equipments etc. complete in all respect.
250	S.I.T.C OF SCADA SYSTEM ON A TUBEWELL
251	CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each tubewell/ OHT & stand alone OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations.
252	G.S.M./G.P.R.S. based wireless communication with 4G modem for RTU/ PLC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer anteena made for pumping plant internet charges.
253	CE & UL certified Inteligent Smart Energy Meter
254	Auto Phase reversal unit with inbuilt time delay and enclosure for above control panel
255	CE & UL certified Hydrostatic type sub soil water level transmitter for tubewell.
256	CE & UL certified pressure transmitter
257	CE & UL certified Surge protector for above control panel
258	CE & UL certified 7\\" HMI touch screen suitable to communication with PLC/RTU local display and control of process parameter.
259	Complete cabling of tubewell including all power and control cables of all equipment at pump house and OHT .
260	Control panel with IP-54 protection industrial grade for all equipment separate for control (24V and power equipments)
261	Installation, commissioning & testing for one tubewell
262	Trial run for three month period for three nos for one tubewell
263	S.I.T.C OF SCADA SYSTEM ON A TUBEWELL
264	CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each ZPS/ OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations.
265	G.S.M./G.P.R.S. based wireless communication with 4G modem for RTU/ PLC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer anteena made for pumping plant internet charges.
266	CE & UL certified Inteligent Smart Energy Meter for each pump
267	Motor operated Actuators with Sluice valve of suitable size 200 mm. at Delivery line of each pump.(1W+1S)
268	Motor operated Actuators with Sluice valve of suitable size 250 mm. at common header.
269	CE & UL certified Electro magnatic flow Meter suitable for line size 250 mm or suitable as per site requirement.
270	Soft starter with RS-485 port-400V Class suitable KW rating for each pump
271	Auto Phase reversal unit with inbuilt time delay and enclosure for control panel.
272	CE & UL certified Radar type water level transmitter for OHT as well as CWR.
273	CE & UL certified pressure transmitter for each pump delivery & common header.
274	CE & UL certified Surge protector for control panel
275	CE & UL certified 7\\" HMI touch screen suitable to communication with PLC/RTU local display and control of process parameter.
276	Complete cabling of CWR including all power and control cables of all equipment at CWR and OHT .
277	Control panel with IP-54 protection industrial grade for all equipment separate for control (24V and power equipments)
278	Installation, commissioning & testing for CWR
279	Trial run for three month period for one CWR
280	SCADA WORKS FOR NEWLY PROPOSED OVERHEAD TANK 1350KL HAVING A TUBEWELL WITHIN ITS CAMPUS IN ZONE-1
281	Motor operated Actuators with Sluice valve of size 450 mm. at distribution line.
282	CE & UL certified Electomagnetic Flowmeter for OHT line size 450 mm. dia.
283	CE & UL certified Radar type level transmitter for OHT
284	Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system .
285	Installation, commissioning & testing for of above items at OHT
286	Trial run for three month period for one OHT
287	Trial Run & Maintenance of Three Months including staff & Consumables (excluding electricity charges) of all Tube Wells
288	Trial Run & Maintenance of Three Months including staff & Consumables (excluding electricity charges) of CWR Zone-1.
289	Zone-2 (New Tubewells)
290	Drilling of borehole for Tubewell contruction by RC Rig Machine including transportation, erection, dismantling of Rig and assoiated T & P complete in all respect including required all material, labour etc.
291	Transportation, Erection and Dismantling of Rig Machine
292	Drilling of 500mm size bore from
293	(i) 0M BGL to 100MBGL
294	(ii) 100M BGL to 140MBGL
295	Zone testing in water quality problem areas including all required material, labour, T&P etc. complete in all respect.
296	Tubewell AssemblyM.S. tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) rings, well cap, bail plug, clamp, reducer, central guide, support structer etc. as required & as per typed design complete in all respect.
297	200 mm. Dia MS ERW Housing/ casing/ Slotted pipe having wall thickness of 7.1mm.
298	Supply of pea gravel
299	Logging of bore hole by departmental / approved electric logger.
300	Lowering of Tube well assembly duly welded including welding electrode and shurounding of pea gravel complete in all respect.
301	Lowering of 200mm dia pipe from 0 to 100m deep BGL.
302	Lowering of 200mm dia pipe from 100 to 130m deep BGL.
303	Development of Tubewell by compressor
304	Transportation, Installation and Dismantling of Air Compressor
305	Development of Tubewell by 250 PSI or requisite Capacity of Air compressor
306	Development of Tubewell by O.P. Unit
307	Transportation, Installation and Dismantling of O.P. Unit & Yield Test.
308	Development of Tubewell by 3 Cusec or requisite Capacity of O.P. Unit
309	Chemical and Bacterological test of water sample from depaprtmental/ approved lab.
310	Provision of failed attempt of tubewell construction due to various reasons such as poor strata, less aquifer volume, quality problem area or any other issue whatsoever encountered during work execution.
311	Rebore Tubewell
312	Drilling of borehole for Tubewell contruction by RC Rig Machine including transportation, erection, dismantling of Rig and assoiated T & P complete in all respect including required all material, labour etc.
313	Transportation, Erection and Dismantling of Rig Machine
314	Drilling of borehole for Tubewell contruction by RC Rig Machine including transportation, erection, dismantling of Rig and assoiated T & P complete in all respect including required all material, labour etc.
315	(i) 0M BGL to 100MBGL
316	(ii) 100M BGL to 140MBGL
317	Zone testing in water quality problem areas including all required material, labour, T&P etc. complete in all respect.
318	Tubewell AssemblyM.S. tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) rings, well cap, bail plug, clamp, reducer, central guide, support structer etc. as required & as per typed design complete in all respect.
319	200 mm. Dia MS ERW Housing/ casing/ Slotted pipe having wall thickness of 7.1mm.
320	Supply of pea gravel
321	Logging of bore hole by departmental / approved electric logger.
322	Lowering of Tube well assembly duly welded including welding electrode and shurounding of pea gravel complete in all respect.
323	Lowering of 200mm dia pipe from 0 to 100m deep BGL.
324	Lowering of 200mm dia pipe from 100 to 130m deep BGL.
325	Development of Tubewell by compressor
326	Transportation, Installation and Dismantling of Air Compressor
327	Development of Tubewell by 250 PSI or requisite Capacity of Air compressor
328	Development of Tubewell by O.P. Unit
329	Transportation, Installation and Dismantling of O.P. Unit & Yield Test.
330	Development of Tubewell by 3 Cusec or requisite Capacity of O.P. Unit
331	Chemical and Bacterological test of water sample from depaprtmental/ approved lab.
332	Provision of failed attempt of tubewell construction due to various reasons such as poor strata, less aquifer volume, quality problem area or any other issue whatsoever encountered during work execution.
333	PUMPING PLANT OVER NEW TUBEWELL NO.-1 IN ZONE-2
334	SITC of Submersible pumpset (450 LPM discharge 80 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Volatge Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
335	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
336	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
337	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
338	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
339	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
340	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
341	PUMPING PLANT OVER NEW TUBEWELL NO.-2 IN ZONE-2
342	SITC of Submersible pumpset (450 LPM discharge 87 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
343	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
344	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
345	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
346	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
347	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
348	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
349	PUMPING PLANT OVER TUBEWELL NO.-3 (Existing/Reboring) IN ZONE-2
350	SITC of Submersible pumpset (450 LPM discharge 88 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
351	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
352	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
353	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
354	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
355	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
356	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
357	Cost for shifting and subsequent erection of 0.433 KV L.T.Power Supply with connected material from old tubewell to location of rebore tubewell complete in all respect.
358	Dismantling of old puming plant with rusted 6 \\" dia column pipes,panel,stabilizer ,their accessories etc with transportation of material in nagar palika store .
359	PUMPING PLANT OVER NEW TUBEWELL NO.-4 IN ZONE-2
360	SITC of Submersible pumpset (450 LPM discharge 79 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
361	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
362	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
363	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
364	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
365	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
366	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
367	PUMPING PLANT OVER NEW TUBEWELL NO.-5 IN ZONE-2
368	SITC of Submersible pumpset (450 LPM discharge 108 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
369	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
370	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
371	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
372	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
373	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
374	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
375	SITC of Automatic type chlorinating plant solenoid driven dosing pump of capacity 0-6 LPH ( pressure 4kg/cm2 with ORP sensor to check and regulate the dosing along with 200 ltr capacity HDPE tank (02 nos., 1W+1S) ,standard fittings, wall/floor mountings MS bracket for dosing pump with GM Valve ,cock valve & sodium hydro chloride solution.,chlorine test kit with O.T. Solution complete with all respect.( suitable for 100-220V and 30-60 Hz , suction lift- 1.5 m., injection pressure 4 bars, steadt state accuracy +-3% repeatability +-3%) with RS 485 Port O/P having facility of interface with PLC SCADA system. ( As this tubewell feeds OHT directly)
376	PUMPING PLANT OVER NEW TUBEWELL NO.-6 IN ZONE-2
377	SITC of Submersible pumpset (450 LPM discharge 86 mtr. head coupled with suitable KW rating of electric Motor A.C. Three phase) with 24 m. column pipes, NRV,CI D/F Bend 90*, CI A/F Tee, D/F pipe ( 1.5 m. long 02 nos., 1.0m. Long), Earthing,Painting ,Toolset, Servo Voltage Stablizer,Wiring of pumphouse internal & external, Chainpulley Block and all Pumping Plant accessories with nut bolts and Rubber packing etc.complete in all respect with all required material, T&P labour etc.
378	Motor operated Actuators with Sluice valve of size 100 mm. or suitable size at Main line and Bye-pass line as well.
379	CE & UL certified Electromagnatic Flowmeter suitable for above line size 100 mm. or suitable size.
380	Soft starter with RS-485 port-400V Class suitable for above rating of motor.
381	3 Mtr. long heavy duty size 100mm dia or suitable size column pipe same as above spare.( 01 No. set has 02 nos. column pipes)
382	Supply & Laying of Additonal XLPE insulated Copper Flat submersible conductor of size 2x3cx10 sq mm. for submersible pump set.
383	Supply & Laying of PVC insulated Al. armoured cable size 1x3.5/4Cx16 sq mm. from transformer LV side to meter panel and meter panel to starter.
384	S.I.T.C. OF PUMPING PLANTS & ELECTRIC SUBSTATION IN C.W.R., ZONE-2
385	PumpSet at C.W.R:
386	Supply of Clearwater Botton -Suction Submersible Pumpset having Speed 2900 RPM coupled with suitable KW rating of Electric motor compatible for handling Clear Water with Automatic Coupling Pumpset accessories etc. complete in all respect and also having following parameters:-(a) Capacity 2150 LPM(b)Total head 45 Mtrs.(c) Delivery size suitable(d) Material of Construction-:(i) Casing- CI IS210 FG260(ii) Impeller - CF8M, BHN 180 approx(ii) Shaft - SS 410 (iii) Bearing- anti frictional (e) Operational Voltage 380±10% 3 phase AC Supply. (f) Pumpset accessories such as duck foot bend, pedestal auto coupling with guide pipe only in S.S. for pump set. Total nos. of 02 Pumpsets are proposed in module of operation in 01 nos. are working , 01 Pump is standby . (NOTE- Pump Discharge, Head & motor HP are tentative and may vary as per actual site condition at the time of execution.)
387	Cast iron pipes & specials.
388	Supply of galvanized nut- Bolt SS-304 and rubber packing material for erection of above.
389	Reflex Valve
390	CIDF double flanged single/multi door swing check valves PN 1.0 FG200 Grade having body comprising inlet & outlet sheets in gradeed cast iron diaphragm fitted woth st. steel, faces,diaphragm plate and door , sub pins and shall be of following sizes:
391	200 mm dia
392	250 mm dia
393	CI Dismantling joints
394	200 mm dia
395	250 mm dia
396	E.O.T. Monorail Travelling trolley with chain pulley block.
397	E.O.T. Monorail Travelling Trolley with spur gear of 3.0 tonne capacity with chain pulley block with suitable lift and span as per approved Structural GAD of pumping station.
398	Automatic type Chlorinating Plant
399	SITC of SCADA Compatible Automatic type chlorinating plant solenoid driven dosing pump of capacity 0-20 LPH or suitable capacity, pressure 4kg/cm2 with ORP sensor to check and regulate the dosing along with 500 ltr capacity HDPE tank ,standard fittings, wall/floor mountings MS bracket for dosing pump with GM Valve ,cock valve & sodium hydro chloride solution 40 ltrs.,chlorine test kit with O.T. Solution complete with all respect.( suitable for 100-220V and 30-60 Hz , suction lift- 1.5 m., injection pressure 4 bars, steadt state accuracy +-3% repeatability +-3%).
400	L.T. Panel Board suitable for operation on 400 V, 3 Phase 50 Hz. A.C. supply in sheet steel enclosure in cubical pattern floor mounting with following fitted on the phase of the panel with bus incomer bar of 320 amps. Capacity, Aluminium Bus Bar size of 40*10 mm. and neutral of half the capacity sectionalized through a bus section. The panel shall comprise of the following. 02 No. incoming feeder from 01 Nos. LT feeder & 01 Nos. spare for future use with following details:-02 nos. MCCB of 250 amps,50 KA Micro processor type for Two incomer preferably schneider/ABB with indication lamp mechanical on/off indicator.One set of current transformer of ratio 300/5AOne No. CT operated ammeter 0-300A with ammeter One No. Voltmeter 0-500 V with voltmeter One No power factor meter 0.5 lag/ 1-0.5 lead One No Surge arrestor Relay & One no. UV/OV RelayOne No frequency meter.Total Nos. of Outgoing feeder as follows-MCCB of 125 amps,50KA capacity with indication lamp mechanical on/off indicator. -02 nos.Ammeter with selector switch.Single phasing preventer. Sets of timer and relays for overload and underload. 01 Nos. 63 Amps. MCCB for RTU/PLC Panel.01 Nos. 63 Amps. MCCB as Misc. load02 Nos. 32 Amps. 4P MCCB for lighting & spare one.
401	Supply of 01 No. required rating of APFC Panel with capacitor bank and feeder SFU & MCCB 63 Amp., 25 KA with APFC relay & other acceessories to adjust automatically the power factor close to upf.
402	Power and control cables
403	1100 V grade, 3.5 core x 35 mm2 PVC insulated PVC sheathed Aluminium Armoured conductor cable from LT panel to starters.(1x2x75 mtr.)
404	1100V grade, 2x3C x16 mm2 PVC insulated PVC sheathed submersible copper flat cable to motor 3 Nos pumps. (2x2x25 mtr.)
405	Control cable 1x10C, 1.5 mm2 PVC insulated PVC sheathed Copper conductor cable for moisture sensor Reverse protection thermistor relay etc.
406	EARTHING
407	Complete earthing of all the equipments as detailed above shall be done as per IS/IER/PWD specification with G.I Plates, watering pipe and loop earthing with adequate size of G.I/ Al. strip etc. (PS-702) Each of the equipment (Pumps + LT Panel + PLC Panel.) size of earthing plate 600mm x 600mm x6 mm with salt and coal.
408	Lighting system:
409	Supply & erection of M.S. Tubular Poles SP-36, 9.5 M height.
410	S/F of 72 watt LED with lumen reflector.
411	Feeder pillar for lighting
412	Supply and laying of 4x16mm2 Al. armoured cable.
413	Internal electrification with fixtures.
414	S/F 1200 mm ceiling Fan for LT Room
415	S/F of exhaust Fan for LT Room.
416	Earthing of street light pole (SOR-41)
417	Painting of street light (P5-634)
418	Supply and installation of DCP type of 5 Kg. Fire existinguisher (PS-1132)
419	12 mm thick rubber mating for safe working on.
420	Tools and Spanners:
421	Hydrulic crimping tools- Crimping range: 16-300 sq.mm.,Weight: 6 Kg. ,Length: 500mm
422	Mannual crimping tools- Crimping range: 400 sq.mm.
423	Tong tester (AC/DC-1000A) Multimeter (AC/DC-1000A) Megger (AC/DC-500V) Screwdriver (6\\"x 12\\") Plier (250mm)
424	Chain wrench (12\\"x18\\"), Pipe wrench (1200mm)
425	Chequered plate of required size so as to cover all trenches.
426	Erection or Installation with earthing of All above equipments complete in all respect.
427	Testing of All above equipments etc. complete in all respect.
428	Commissioning of All above equipments etc. complete in all respect.
429	S.I.T.C OF SCADA SYSTEM ON A TUBEWELL ( 5 New+ 1 Rebore)
430	CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each tubewell/ OHT & stand alone OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations.
431	G.S.M./G.P.R.S. based wireless communication with 4G modem for RTU/ PLC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer anteena made for pumping plant internet charges.
432	CE & UL certified Inteligent Smart Energy Meter
433	Auto Phase reversal unit with inbuilt time delay and enclosure for above control panel
434	CE & UL certified Hydrostatic type sub soil water level transmitter for tubewell.
435	CE & UL certified pressure transmitter
436	CE & UL certified Surge protector for above control panel
437	CE & UL certified 7\\" HMI touch screen suitable to communication with PLC/RTU local display and control of process parameter.
438	Complete cabling of tubewell including all power and control cables of all equipment at pump house and OHT .
439	Control panel with IP-54 protection industrial grade for all equipment separate for control (24V and power equipments)
440	Installation, commissioning & testing for one tubewell
441	Trial run for three month period for three nos for one tubewell
442	S.I.T.C OF SCADA SYSTEM FOR C.W.R. ZONE-2
443	CE & UL Certified PLC/ RTU in IP 54 enclosure suitable to communicate with GSM based modem unit with CPU & Power supply with analog & digital parameter & features as specified, for each ZPS/ OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations.
444	G.S.M./G.P.R.S. based wireless communication with 4G modem for RTU/ PLC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer anteena made for pumping plant internet charges.
445	CE & UL certified Inteligent Smart Energy Meter for each pump
446	Motor operated Actuators with Sluice valve of suitable size 200 mm. at Delivery line of each pump.(1W+1S)
447	Motor operated Actuators with Sluice valve of suitable size 250 mm. at common header.
448	CE & UL certified Electro magnatic flow Meter suitable for line size 250 mm or suitable as per site requirement.
449	Soft starter with RS-485 port-400V Class suitable KW rating for each Motor.
450	Auto Phase reversal unit with inbuilt time delay and enclosure for control panel.
451	CE & UL certified Radar type water level transmitter for OHT as well as CWR.
452	CE & UL certified pressure transmitter for each pump delivery & common header.
453	CE & UL certified Surge protector for control panel
454	CE & UL certified 7\\" HMI touch screen suitable to communication with PLC/RTU local display and control of process parameter.
455	Complete cabling of CWR including all power and control cables of all equipment at CWR and OHT .
456	Control panel with IP-54 protection industrial grade for all equipment separate for control (24V and power equipments)
457	Installation, commissioning & testing for CWR
458	Trial run for three month period for one CWR
459	SCADA WORKS FOR NEWLY PROPOSED OVERHEAD TANK 1050 KL HAVING A TUBEWELL WITHIN ITS CAMPUS IN ZONE-2
460	Motor operated Actuators with Sluice valve of size 400 mm. at distribution line.
461	CE & UL certified Electomagnetic Flowmeter for OHT line size 400 mm. dia.
462	CE & UL certified Radar type level transmitter for OHT
463	Chlorine Analyzer with MODBUS RTU having following specifications- (a) FRC Sensor (Senssit make), range- 0-5 PPM (electrolyte with membrane cap), tytpe-Amperometric. (b) Analyzer with RS 485O/P. suitable to OHT distribution line size & compatible with SCADA system too.
464	Installation, commissioning & testing for of above items at OHT
465	Trial run for three month period for one OHT
466	Trial Run & Maintenance of Three Months including staff & Consumables (excluding electricity charges) of all Tube Wells
467	Trial Run & Maintenance of Three Months including staff & Consumables (excluding electricity charges) of CWR Zone-2.
468	MASTER CONTROL STATION (M.C.S.)
469	CE & BIS approved manufacturer's industrial grade LED monitor size 65\\" with latest configuration as per specification mentioned in tender documents.
470	Desktop/PC with i7 processor as per specification mentioned in tender documents.
471	CE/UL approved manufacturer's 5 KVA UPS with batteries as per specification mentioned in tender documents.
472	Full development version of required TAGS SCADA software suitable for digital and analog input/output features with customization of software as per requirement as per spec. mentioned with unlimited digital and analog Input/Output features specified in detailed technical document with customization of software as requirement
473	CE & UL approved manufacturer's control room PLC with Redundant CPU & power supply at MCS in IP54 enclosure as per specification mentioned in tender documents.
474	CE/UL certified field gateway agent for transfering data from MCS to Central control room(C.C.R.)
475	GSM based wireless / broadband/Equipment communication system for PLC capable to transfer and retreive data & gather data from remote sites to control stations, including all accessories complete. All accessories included signal enhancer antenna along with running expenses till DLP.
476	CE/UL approved manufacturer's Firewall for network protection
477	Surge protector for ethernet communication protection
478	CE/UL approved manufacturer's industrial grade ethernet switch
479	Mobile App facility system architecture complete.( industries internet based & viewed through mobile apps for increased local & remote visibility)
480	Canon/HP/equivalent Laser printer
481	Security Survelliance IP camera with recorder.
482	Installation, testing and commissioning of M.C.S. with required furniture, fans, table, chairs, Almirah, Air Conditioner etc
483	Test and trial run of M.C.S.
484	Trial Run & Maintenance of M.C.S for Three Months including staff (excluding electricity charges) Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Services Tenders

Civil Engineering Services Tenders

Soil Survey Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Survey, Soil Investigation, Design, Supply Of All Materials, Labour, T&P Etc. Required For Construction, Erection, Completion, Testing & Commissioning Of Water Supply Works Such As Reinforced Cement Concrete Ohts, Tubewells, Zpss/Cwr Cum P, Fatehabad-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Survey, Soil Investigation, Design, Supply Of All Materials, Labour, T&P Etc. Required For Construction, Erection, Completion, Testing & Commissioning Of Water Supply Works Such As Reinforced Cement Concrete Ohts, Tubewells, Zpss/Cwr Cum P, Fatehabad-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us