|
| 1 | Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge |
| 2 | Removing mortar from bricks work in cement mortar and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured) |
| 3 | Dismantling doors, windows and clerestory windows (steel or wood) shutter of area 3 sq. metres and below including chowkhats, architrave, hold fasts etc. complete and stacking within 50 metres lead . |
| 4 | Dismantling tile work for thickness of tiles 10 mm to 25 mm in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 5 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases. |
| 6 | Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement : four sand : eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) in foundation and plinth including curing complete excluding the cost of form work but including carriage of material with in all leads, lift, and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals. |
| 8 | Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in all height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:- |
| 9 | Suspended floors, roofs, landings, balconies and access platform. |
| 10 | Lintels, beams, plinth beams, girders,bressumers and cantilevers. |
| 11 | Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including straightening, cutting ,bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in cement mortar 1:6 (one cement : six coarse sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 13 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level Cement mortar 1:4 (1 cement :4 coarse sand) including curing complete and carriage of material with in all leads, lifts and other incidentals. complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 14 | Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 15 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite of any colour and shade, area of slab over 0.50 sqm for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 16 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 17 | Providing wood work in frames of doors ,windows ,clerestory, windows and other frames wrought ,framed and fixed in position of second class deodar wood including carriage of material with in all leads , lifts and other incidentals, complete in all respect. |
| 18 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of material with in all leads , lifts and other incidentals,. |
| 19 | Providing and fixing 40mm (forty millimeters) thick panelled glazed or panelled and glazed shutters for doors windows and clerestory windows, including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals . |
| 20 | Providing and fixing 40mm (forty millimeters) thick wire gauge shutters for doors windows and clerestory windows, using galvanized MS wire gauge of IS gauge desigination 85 G with wire of dia 0.56mm including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals . |
| 21 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 22 | Providing and fixing 40mm (forty millimeters) thick panelled glazed or panelled and glazed shutters for doors windows and clerestory windows, including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals . |
| 23 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Areaof opening for panel inserts excluding portion in side grooves or rebates to be measured).Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 5.0mm thick glass panes (weight not less than 12.5 kg per sqm) including carriage of material with in all leads , lifts and other incidentals |
| 24 | Providing and fixing Kiln seasoned and chemically treatedhollock wood , wooden moulded beading 50x12mm (fifty X twelve mili metre) to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete |
| 25 | Providing and fixing M.S. grills fixed to openings /wooden frames with rawl plugs screws etc. of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of material with in all leads , lifts and other incidentals. |
| 26 | Providing and fixing M.S. grills fixed to openings /wooden frames with rawl plugs screws etc. of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of material with in all leads , lifts and other incidentals. |
| 27 | Providing and fixing Stainless Steel sliding door bolts, ISI marked to required colour or shade, with nuts and screws etc. complete : |
| 28 | 300x16 mm |
| 29 | 200x16 mm |
| 30 | Providing and fixing Stainless Steel tower bolts, ISI marked, to required colour or shade, with necessary screws etc. complete : |
| 31 | 300x10 mm |
| 32 | 100x10 mm |
| 33 | Providing and fixing 50 cm long Stainless Steel kicking plate of size 100x3.15 mm, to required colour or shade, with necessary screws etc. complete |
| 34 | Providing and fixing Stainless Steel tower bolts, ISI marked, to required colour or shade, with necessary screws etc. complete : |
| 35 | 150 mm |
| 36 | 100 mm |
| 37 | Providing and fixing Twin rubber stopper Stainless Steel hanging floor door stopper, ISI marked, to required colour and shade, with necessary screws etc. including carriage of material with in all leads , lifts and other incidentals . |
| 38 | Providing and fixing bright finished Stainless Steel casement stays (straight peg type) , with necessary screws etc.complete.200mm weighing not less than 240gms including carriage of material with in all leads , lifts and other incidentals . |
| 39 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of material with in all leads , lifts and other incidentals. |
| 40 | Providing and laying vitrified floor tiles in size of tile 600x600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material with in all leads , lifts and other incidentals |
| 41 | Providing and laying Vitrified tiles in Size of 600x600mm sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of material with in all leads , lifts and other incidentals . |
| 42 | 6 mm(six millimeter) thick cement plaster to ceiling in cement mortar 1:3 (one cement :three sand as per direction of engineer-in- charge including carriage of material with In all leads , lifts in all floors and other incidentals. |
| 43 | 15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement :six sand )as per direction of engineer in charge including carriage of material within all leads lifts in all floors and other incidental . |
| 44 | Repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 45 | Distempering Two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. |
| 46 | Providing and fixing Stainless Steel tower bolts, ISI marked, to required colour or shade, with necessary screws etc. complete : |
| 47 | 150 mm |
| 48 | 100 mm |
| 49 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 50 | Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface |
| 51 | Providing and fixing tiled false ceiling of 3mm thick ACP sheet as per design and pattern specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge 3 mm thick ACP sheet as per design and pattern. including carriage of materials with in all leads, lifts and other incidentals.. |
| 52 | Providing and fixing W.C. pan with ISI marked white solid plastic seat and lid white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 53 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 54 | Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface |
| 55 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 56 | Providing and fixing 510x1040 mm bowl depth 225 Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 57 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge |
| 58 | Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 59 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 60 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 61 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete |
| 62 | Providing and fixing C.P. brass toilet paper holder : |
| 63 | Providing and fixing 45 cm length 15 mm nominal bore uplasticised PVC connection pipe with brass unions |
| 64 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 65 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 66 | Providing and fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 67 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 68 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 69 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design including carriage of material with in all leads , lifts and other incidentals. |
| 70 | Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 71 | Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 72 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 73 | 15 mm nominal outer dia Pipes |
| 74 | 20mm nominal outer dia Pipes |
| 75 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc |
| 76 | Concealed work, including cutting chases and making good the walls etc |
| 77 | 20 mm nominal outer dia Pipes |
| 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge |
| 79 | 15 mm nominal outer dia Pipes |
| 80 | 20mm nominal outer dia Pipes |
| 81 | Providing and fixing PPR Unions 20mm |
| 82 | Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. |
| 83 | Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe) |
| 84 | Providing and fixing 15 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. |
| 85 | Providing and fixing 110mmx90mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete |
| 86 | Providing and fixing pvc Poly plast sewerage pipe of working pressure not less than 4.5 kg per square metre (Four point five kilogramme per square metre) including filling the joints with approved adhesive complete. 75mm dia pipes |
| 87 | 110mm dia |
| 88 | 75mm dia |
| 89 | Providing and fixing pvc Poly plast sewerage pipe of working pressure not less than 4.5 kg per square metre (Four point five kilogramme per square metre) including filling the joints with approved adhesive complete. 75mm dia pipes |
| 90 | 75mm dia |
| 91 | 110mm dia |
| 92 | Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixd to wooden cleats with C.P. Brass screws complete including carriage of material with all leads and lifts. |
| 93 | Providing and fixing C.P. Brass towel rail of size 600mmx20mm complete with C.P. Brass brackets fixed to wooden plugs with CP brass screws complete including carriage of material with all leads and lifts. Please Enable Macros to View BoQ information |
