|
| 1 | Entrannce Gate of the Ram Shrushti Tapovan The scope of work under this tender includes the conceptualization, design, engineering, fabrication, supply, transportation, erection, installation, testing, and commissioning of the Main Entrance Gate Structure:Gate length - 5.10m , ht - 2.94 m.Entrance Curved wall :Moulding from top [total 4]( Two on each side): ht-0.20m, length - 8.52 m. Decorative sculptures, architectural elements, landscaping features, and all associated civil, structural, and artistic works at the project site, as per the approved drawings, specifications, and directions of the Engineer-in-Charge. |
| 2 | Entrance Pillars (Both Sides)Providing and Constructing Two Reinforced Cement Concrete (RCC) Decorative Pillars, each measuring 1.23 m × 1.23 m in cross-section and 3.66 m in height, including design, shuttering, reinforcement, concreting, and finishing complete. Each pillar shall be cast in RCC of M25 grade using approved quality cement, sand, and aggregates, with embedded steel reinforcement (Fe500 grade) as per structural design. The outer surfaces shall incorporate decorative moulding and artwork crafted using cement-based motifs and IOS-certified fire-retardant resin fiber detailing, seamlessly integrated into the RCC structure. The finished surface shall be treated with weather-resistant protective coating and finished in sandstone texture paint to match the main entrance wall. The rate shall include all materials, labour, formwork, reinforcement, artwork, scaffolding, curing, finishing, transportation, and all incidental works complete as per approved design and as directed by the Engineer-in-Charge. |
| 3 | Boundary Wall DECORATIVE FINISHING WORK Boundary Wall Natural Sandstone Cladding — Cladding: The exposed surface of the wall shall be finished with machine-cut natural sandstone cladding of 20–25 mm thickness, jointed with matching color grout and fixed using stainless steel clamps and polymer adhesive to ensure long-term bonding and durability.Decorative Elements: The top edge of the wall shall include a 0.20 m high × 8.52 m long decorative moulding, fabricated in IOS-certified fire-retardant resin fiber (FRP), fixed securely over the RCC coping beam using chemical anchors and fasteners. The moulding shall be artistically designed to match the architectural tone of the entrance.Finish: The entire wall surface, including cladding and FRP moulding, shall be coated with weather-sealed transparent laminate or UV-protective clear coat to prevent moisture ingress, fading, or surface deterioration. The finish shall provide long-term protection and maintain natural stone texture aesthetics.Inclusions: The rate shall include excavation, foundation, RCC framework, brick masonry, stone cladding, FRP moulding, finishing, curing, scaffolding, transportation, and all materials, labour, tools, and incidentals required for completion in all respects |
| 4 | High Relief Wall Murals Providing and Fixing High-Relief Wall Murals — Ramshrushti Tapovan Theme — Design, fabrication, and installation of artistic high-relief murals, each of approximate size 1.72 m in height and 2.15 m in width, depicting thematic sculptures inspired by Ramshrushti Tapovan. The work shall include design detailing, 3D modelling, material selection, fabrication, finishing, transportation, and installation complete in all respects as per the approved concept and direction of the Engineer-in-Charge.Material: Each mural shall be crafted using a combination of IOS-certified fire-retardant resin fiber (FRP), cementitious material, and metal reinforcement frame (MS, SS as approved) to provide structural strength, dimensional stability, and long-term weather resistance. The mural surface shall incorporate detailed artistic carving, texturing, and relief depth consistent with the approved design theme.Fixing & Support: Murals shall be mounted on vertical walls or pre-approved RCC backing using a concealed anchoring system, with corrosion-resistant hardware (SS-304 bolts, chemical anchors, or equivalent). The fixing arrangement shall be designed to withstand wind load, vibration, and temperature variations. All mounting details shall be shop-drawn and approved prior to installation.Finish: The mural surface shall receive a multi-layer weatherproof coating consisting of primer, color base, and UV-protective topcoat in natural stone or metallic tones as per the artistic intent. Finishes shall be washable, anti-fungal, and fade-resistant, suitable for outdoor exhibition.Inclusions: The rate shall include cost of design development, mock-up sample preparation, fabrication, transportation, lifting, fixing hardware, scaffolding, surface finishing, protective coating, and all materials, labour, and incidentals required for completion in all respects as per specifications and drawings. |
| 5 | Decorative Kalash Providing and Fixing Decorative High-Relief Kalash Elements — Work includes the design, fabrication, and installation of decorative Kalash mounted on top of pillars, gate structures, and wall sections as per the approved architectural design and directions of the Engineer-in-Charge.Size: Each Kalash shall be of 0.89 m height with proportionate diameter, designed in classical form with detailed relief ornamentation.Material: Each finial shall be fabricated using a combination of high-strength cement composite and IOS-certified fire-retardant resin fiber (FRP), reinforced internally with mild steel or stainless steel rods to ensure rigidity and long-term stability under outdoor exposure.Fabrication & Detailing: The Kalash shall feature artistic carving, embossed motifs, and contour detailing. The internal metal reinforcement shall extend into the fixing base for secure anchorage.Fixing: Each Kalash shall be anchored to the top surface of the RCC pillar or wall coping using chemical fasteners, stainless steel bolts, and epoxy grout to ensure permanent, vibration-free installation. Concealed anchoring details to be approved prior to execution.Finish: The surface shall receive a multi-layer weatherproof protective coating, including primer, exterior-grade paint, and a UV-resistant clear coat, giving a natural stone or antique metallic finish as per architectural intent. All coatings shall be washable, anti-fungal, and fade-resistant to withstand outdoor climatic conditions.Inclusions: The rate shall be inclusive of all materials, design development, moulding, finishing, installation, scaffolding, labour, and transportation, complete in all respects as per drawings and instructions of the Engineer-in-Charge |
| 6 | Granite Coping of the Wall Providing and Fixing DECORATIVE Granite Coping on Wall Tops — Work includes the supply, fabrication, and installation of granite coping stone over the top surface of the boundary wall, pillars, and moulded sections to protect cladding and decorative elements, complete as per approved design and direction of the Engineer-in-Charge.Size & Quantity: Granite coping of total length 16.58 m and width 0.45 m, including all cutting, dressing, jointing, and finishing complete.Material: The coping shall be made from premium-grade, weather-resistant granite stone, free from cracks, veins, or discoloration, having a uniform grain texture and consistent color tone (as per architect’s approval).Fixing Method: The coping shall be machine-cut, edge-chamfered, and bedded on a 20 mm thick cement mortar (1:4) with full contact bedding. Joints shall be filled with non-shrink polymer grout and aligned to ensure smooth continuity. Stainless steel cramps or dowels (minimum 6 mm dia.) shall be provided at all joints for anchoring with the RCC coping beam or wall top.Surface Treatment: The exposed surface shall be machine-polished to a semi-gloss finish and laminated with weather-protective, UV-resistant clear sealant to prevent moisture penetration and discoloration. The surface shall be washable, anti-fungal, and stain-resistant.Inclusions: The rate shall include all materials, cutting, edge chamfering, polishing, fixing, sealing, curing, scaffolding, and cleaning, complete in all respects as per specifications and drawings. |
| 7 | Name Inscription Panel Providing and Fixing Name Inscription Panel – “रामसृष्टी तपोवन (Ramshrushti Tapovan)” — Design, carving, supply, and installation of natural sandstone name signage panel of size Length 2.40 m × Height 1.22 m, Total No. 2 Both Sides, including lettering, detailing, finishing, and fixing complete as per approved design and direction of the Engineer-in-Charge. Ram Sculpture beside Ram srushti lettering (Total 4) - [2 on each side ]Length - 2.84 m, Height - 1.43m.Area from bottom to floor till moulding ( bottom of curved surface) - 0.56m, length - 8.34 m (Total 4) 2 on each side -Bottom moulding ht - 0.20m ,length - 8.34 x 4 = 33.36. Material: The inscription panel shall be carved from a single or jointed block of natural fine-grained sandstone, free from cracks, discoloration, or veins, conforming to IS 3620. Stone shall be of uniform texture and approved shade, suitable for detailed carving and outdoor exposure. Workmanship & Carving: The panel shall feature high-relief stone carving of the text “रामसृष्टी तपोवन (Ramshrushti Tapovan)” in Devanagari and English script, crafted by skilled stone artisans. Lettering depth, alignment, and spacing shall conform to the approved 3D design or mock-up. The carved surface shall be polished smooth, edges chamfered, and corners eased to prevent chipping. Fixing & Mounting: The sandstone panel shall be mounted securely on the wall surface using a concealed stainless-steel (SS-304) anchoring system with mechanical,chemical fasteners and metal framing support at the back. Joints, if any, shall be filled with matching color stone grout and sealed to prevent moisture ingress. The support framework shall be designed to resist wind and vibration loads. Finish: The carved surfaces shall be treated with a weather-resistant protective coating and a clear matte sealer to enhance durability, UV resistance, and color stability. The final finish shall maintain the natural texture and aesthetic of the stone. Inclusions: The rate shall include stone procurement, carving, polishing, lettering, backing frame fabrication, fixing hardware, scaffolding, lifting, installation, cleaning, and finishing, complete in all respects as per drawings and specifications. |
| 8 | Electrical Fixtures for the Entrance Gate and Decorative Lamp Fixtures Providing, Supplying, and Fixing Decorative Lamp Fixtures with Dual LED Heads for Ornamental Street Poles — Work includes fabrication, supply, and installation of classical-style twin lamp head fixtures on 3.66 m high-12 In total, decorative poles, complete with all accessories, foundation works, electrical connections, and finishing, executed as per approved drawings and the directions of the Engineer-in-Charge. 1. Lamp Fixture Design & Construction: •Each pole shall be provided with two (2) decorative lamp heads, symmetrically mounted on top or on twin curved arms. •Each lamp head shall be of heritage, classical design, made of die-cast aluminium body, and fitted with integrated LED lighting unit of 25–30 W per head (total 50 W per pole). •Diffuser glass shall be made of frosted, toughened glass panels for uniform light diffusion and glare-free illumination. •Lamp heads shall have removable covers for easy maintenance access and cleaning. 2. Finish & Protection: •All external metal surfaces shall be coated with UV-protected, weatherproof polyurethane (PU) paint in antique bronze or approved shade, ensuring long-term outdoor durability and resistance to fading, cracking, or corrosion. •Internal metallic parts (arms, brackets) shall be galvanized and epoxy-primed before PU topcoat application. 3. Electrical Fittings & Wiring: •All internal electrical wiring shall be concealed through the hollow metal core, using heat-resistant, multi-strand copper PVC cables (conforming to IS 694). •Each lamp fixture shall include terminal connectors, earthing provision, and junction box at base level. •Wiring and connections shall comply with IS 732 (Electrical Wiring Code) and IE Rules for outdoor installations. 4. Lighting & Electrical Components: •LED light fittings: IP65-rated, energy-efficient, outdoor type, with die-cast aluminium housing and polycarbonate diffuser, conforming to IS 10322 (Section 3) equivalent to BIS-certified standard. •Electrical supply: 230V, 50Hz AC, single phase. •All fittings shall be factory-tested and BIS-marked, with surge protection and short-circuit safety. •Provision for maintenance access shall be built into the design for replacement of lamps and drivers. 5. Mounting & Foundation: •The lamp post shall be mounted on a reinforced concrete block foundation of minimum 0.45 m × 0.45 m × 0.60 m depth, cast in RCC (1:2:4) mix, with anchor bolts embedded during casting. •Anchor bolts and nuts shall be galvanized steel, conforming to IS 1367 (Part 3) standards. •Proper vertical alignment and levelling shall be ensured during erection. •Final connection to the electrical supply line shall include MCB protection at pole base. 6. Execution & Supervision: •All installation work shall be carried out under supervision of the Engineer-in-Charge, ensuring alignment, level, and finish consistency across all poles. •All materials and accessories shall be pre-approved and installed strictly as per specifications and drawings. Inclusions: The rate shall include the complete lamp fixture (twin head), mounting arms, internal wiring, LED fittings, junction box, anchor bolts, foundation, testing, painting, and commissioning, complete in all respects. |
| 9 | Decorative Garden Sculpture (High-Relief Type) Providing, Fabricating, Finishing, and Installing Decorative Garden Sculpture (High-Relief Type) — Work includes the design, fabrication, supply, and installation of a decorative high-relief sculpture of approved artistic design, measuring approximately 3 sculptures placed in the garden area between street lamps : Base height - 0.52m , length - 0.68m , width- 0.75m, Total ht- 2.9m ( In total 6 sculptures placed alternatively), including all internal framing, base plate, fixing arrangements, surface finishing, and accessories, complete in all respects as per drawings, specifications, and directions of the Engineer-in-Charge. 1. Sculpture Construction: The sculpture shall be made of IOS-grade fireproof resin fibre-reinforced composite (FRP) material, conforming to IS 6746 fire-retardant standards, suitable for long-term outdoor exposure. The FRP shall possess high mechanical strength, dimensional stability, and weather resistance, ensuring durability under sunlight, moisture, and temperature variations. 2. Internal Structure: The internal skeleton shall consist of MS (Mild Steel) framing of minimum 25 mm × 25 mm × 3 mm square hollow sections, fabricated and welded per design to provide adequate rigidity, alignment, and resistance to wind load and handling stresses. 3. Base Plate & Support: The sculpture shall be mounted on a (600 mm × 600 mm × 25 mm) thick MS base plate, fabricated from IS 2062-grade steel, machine-cut and drilled to receive galvanized anchor bolts. The plate shall be integrally welded to the internal frame and properly balanced for stability. 4. Surface Finish: The exterior surface shall be finished in metallic bronze antique paint or other approved artistic finish using a weather-resistant PU (polyurethane) coating system. Coating shall be applied in multiple layers (primer + topcoat + clear PU sealant) to provide long-term UV protection, moisture resistance, and colour retention. The surface shall be smooth, detailed, and textured with high-relief artistry, conforming to the approved sample. 5. Joinery & Reinforcement: All joints between FRP sections shall be reinforced internally with fiberglass mat and epoxy bonding resin, ensuring a monolithic, watertight structure without visible seams. 6. Fixing Arrangement: The sculpture shall be installed on a reinforced cement concrete (RCC) pedestal block of minimum 450 mm × 450 mm × 600 mm depth, cast in 1:2:4 cement concrete mix, using galvanized anchor bolts and nuts (conforming to IS 1367) for fastening. Grouting shall be done with non-shrink cement mortar to achieve full structural stability and level alignment. 7. Execution & Installation: The sculpture shall be transported safely to the site, ensuring no surface or structural damage. Installation shall be carried out by skilled artisans and technicians, maintaining precise vertical alignment and orientation per approved layout. All fixing hardware, nuts, bolts, washers, and base grouting materials shall be included. Final cleaning and surface polishing shall be performed after installation. 8. Protection & Durability: The sculpture shall be designed to withstand outdoor environmental conditions including rain, sunlight, and temperature variations without deformation, cracking, or fading. 9. Warranty: The entire work shall carry a minimum one-year warranty against material defects, surface fading, or deformation under normal environmental exposure. Inclusions: The rate shall be inclusive of design, fabrication, finishing, transportation, installation, base grouting, painting, and all materials, labour, tools, equipment, and incidentals required for satisfactory completion of the work. |
| 10 | Decorative Circular Garden Sitting Area Structure (Round Type) Providing, Fabricating, and Installing Decorative Circular Garden Sitting Area Structure (Round Type) — Work includes complete design, structural fabrication, foundation, seating platform, cladding, finishing, and installation of a decorative circular garden sitting area of overall Total 2- Semi curved seating (larger seating area) , Arc length - 16.80m, seating ht - 0.45m, Total 5 - semi curved seating (smaller seating area), arc length -7.8m , seating ht - 0.45m , radius - 2.50m, Total 2 - Columns on the arc - dimension - 0.44 x 0.44m,Column ht - 2.4m,Total height (floor to top of curved antablature) - 3.45m, Circular seating around tree( total 6):,Outer diameter - 3.70m,Inner diameter- 2.90m,Seating depth - 0.40m,Seating ht- 0.45m, as per approved drawings, specifications, and under the direction of the Engineer-in-Charge. -1. Description of Work:• Construction and installation of a decorative circular garden pavilion , sitting structure comprising structural columns, cornices, arches, roof band, and integrated seating platform.1. Structure Details:(a) Main Structural Frame:• The main frame (columns, arch segments, and cornices) shall be fabricated from IOS-grade fireproof resin fiber composite (FRP) material, with high tensile strength and outdoor durability conforming to IS 6746 , ASTM D635 standards.• Internal reinforcement: MS (Mild Steel) framework made of square hollow sections (minimum 25 mm × 25 mm × 3 mm) and 12 mm dia iron rods, welded and aligned for structural rigidity.• Cavities filled with cement-sand mortar (1:3 mix) for weight balance and vibration resistance.• Total height of the structural portion from base to cornice: Base and Seating Platform:• Circular sitting base constructed in RCC and brick masonry.• RCC foundation (1:2:4 mix using 20 mm graded aggregates) up to plinth level.• Brick masonry (Class 7.5N, IS 1077) in 1:4 cement mortar up to (750 mm) height forming the seating platform.• The inner and outer faces to be finished with machine-cut natural sandstone cladding of minimum 20–25 mm thickness, jointed with matching coloured polymer grout or cement mortar (1:3).• Top surface of the seating platform to be polished smooth and chamfered at edges for comfort.(c) Columns and Roof Elements:• Decorative columns to be FRP moulded elements, internally reinforced with mild steel framing and filled with concrete for stability.• Columns shall be monolithically anchored to the RCC base using anchor bolts (IS 1367) and epoxy grout.• Roof cornice, fascia, and circular cap elements shall be moulded FRP panels finished in natural sandstone tone , approved shade.• All joints between FRP segments to be sealed with weatherproof silicon sealant and finished smooth.-2. Material Specifications:• Resin Fiber (FRP): IOS-certified fire-retardant resin fiber-reinforced polymer, minimum 6 mm thick, conforming to IS 6746 , ASTM D635.• Steel Framework: Mild steel angles , pipes (minimum 25×25×3 mm), conforming to IS 2062.• Concrete: RCC (1:2:4 mix) using 20 mm coarse aggregates, per IS 456:2000.• Bricks: Burnt clay bricks of Class 7.5N, per IS 1077.• Cladding Stone: Machine-cut natural sandstone slabs, 20–25 mm thick, per IS 3620, free from cracks or disintegration.• Finishing: Two coats of UV-protected exterior-grade PU coating over epoxy primer for FRP surfaces, giving natural sandstone or antique tone.-3. Installation and Fixing:• Entire structure to be installed on RCC foundation designed to safely bear dead and live loads.• All components to be pre-fabricated and assembled on site with concealed anchoring, bolted and grouted connections.• Proper alignment, level, circular symmetry, and plumb shall be ensured during erection.• All joints to be sealed using weatherproof polyurethane sealant and finished flush.• All installation to be carried out under direct supervision of the Engineer-in-Charge.-4. Execution and Quality Control:• All works to be executed in compliance with relevant IS codes for FRP fabrication, RCC construction, and finishing.• Dimensional accuracy to be within ±5 mm tolerance.• One mock-up of a single segment (column + arch + seating finish) shall be prepared and approved before final execution.• FRP and steel components to be factory-tested for thickness, coating, and mechanical strength.• Final structure to be inspected for symmetry, surface finish, and stability before acceptance.-5. Inclusions:• Rate shall include all materials, fabrication, transportation, installation, labour, scaffolding, finishing, anchoring, foundation, coating, and curing complete in all respects.• Contractor shall provide as-built drawings and material test certificates for FRP, steel, and concrete.-6. Warranty:• All FRP and coated components shall carry a minimum 3-year warranty against fading, cracking, or deformation under normal outdoor conditions.• PU coatings and sealants shall retain weather resistance for a minimum of 5 years. |
| 11 | Project Overview – The project involves the design, fabrication, supply, transportation, and installation of a monumental sculpture of Lord Shiva with a total height of 9 meters and width of 12 meters, finished in matte black color. The sculpture will be fabricated with structural durability suitable for outdoor installation and long-term public display. 2. Dimensions – Component Dimension: Total Height of Sculpture 9 meters, Total Width of Sculpture 12 meters, Approximate bredth 6–7 meters, Base / Plinth Height 1.5 – 2 meters (as per site design). 3. Structural Framework – Internal Structural System: Heavy duty MS structural framework, Main vertical columns: ISMB 200 / ISMB 250 steel sections, Secondary structure: MS square pipe 75mm × 75mm / 50mm × 50mm, Structural steel thickness: 6 mm – 10 mm. Load Design: Designed to withstand wind speed up to 180 km/h, Structural stability calculated as per IS 875 standards. Anti-Corrosion Treatment: Sand blasting, Zinc rich primer coating, Anti rust epoxy primer. 4. Sculpture Outer Surface Material – Option generally used in monumental sculptures: Preferred Material Fiber Reinforced Polymer (FRP) / GRC Panels, Thickness: 10 mm – 15 mm, Multi layer fiberglass mat with resin, Lightweight and weather resistant OR Bronze Cladding, Thickness: 4 mm – 6 mm bronze sheets, Patinated black finish. For cost-effective government projects FRP is generally recommended. 5. Surface Finish – Exterior finish: Matte black weatherproof coating, UV resistant polyurethane paint system, Anti fungal coating, Life expectancy of coating: 7 years. 6. Fabrication Method – 3D digital modeling and scaling, CNC foam block carving, Clay detailing by sculptor, Mould making, FRP casting panels, Panel joining and surface finishing. 7. Assembly System – Sculpture fabricated in multiple modular sections, Sections transported to site, Joined using steel brackets and chemical anchor bolts, Joint finishing done on site. 8. Lighting Provision – Architectural LED flood lighting, Minimum 6–8 ground lights, Weatherproof IP65 fittings, Electrical conduit inside pedestal. 9. Maintenance – Annual inspection recommended, Repainting cycle: 5 years, Structural inspection every 5 years. 10. Safety Standards – Structure designed as per Indian Standard Codes (IS Codes): IS 800 – Structural Steel Design, IS 875 – Wind Load, IS 456 – RCC Design. 11. Estimated Weight – Material Approx Weight: Steel Structure 18 – 22 tons, FRP Surface 2 – 3 tons, Total Sculpture 20 – 25 tons approx. including scafolding , crane , hyadra if required Please Enable Macros to View BoQ information |
