|
| 1 | Withdrawing the sewage non clog submersible pump motor up to 4HP,415 V, after disconnecting the LT power terminal & necessary closing of sucction & delivery valves,lifting the pump motor set from the existing well with proper care by using over head crane and placing at work floor for necessaary testing/ checking/ repairing purpose (including hire charges of Labour charges and transportation cost). as per direction of EIC. |
| 2 | Rewinding and Repairing and overhauling of 3 phase, 410-440 volts, 50 Hz, 4 HP non clog submersible motor with approved quality Super Enamel copper winding wire of suitable gauge including heating, changing thrust plate, ball retainer and ball including supplying fitting, fixing rings circlips for thrust plate, water seal ring, bush bearing etc. complete as per direction of E.I.C |
| 3 | Installation of pumping machinery with valves, pipe & pipe specials short piece, depth gauge, pressure gauge including hoisting of column pipe, making all electrical and Drainge line inter-connection complete as per direction including supply of necessary materials as reqd. for the work. (including Transportation cost) |
| 4 | Painting of any steel/ iron surface with no. of coats of paints as given below with ready mixed paint/primer of approved make and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. a.One coat of red lead/Zinc chromate primingb.1st coat of synthetic enamel paint over the primer.c.2nd coat of synthetic enamel paint over the 1st coat |
| 5 | Maintenance and overhauling of C.I non-return valve after dismantling it from delivery pipe line and checking part by part, cleaning, lubricating and thorough servicing the valve. This job includes labour charges, consumables like rubber gasket, sundry cleaning materials,lubricants & replace damage parts as per instruction (spare cost excluded) & refitting of all parts with proper alignment as per direction for valve dia 250 to 600mm |
| 6 | Maintenance and overhauling of isolating sluice valve after dismantling it from delivery pipe line and checking part by part, cleaning, lubricating and thorough servicing the valve. This job includes labour charges, consumables like rubber gasket, sundry cleaning materials,lubricants & replace damage parts as per instruction (spare cost excluded) & refitting of all parts with proper alignment as per direction. for valve dia 250 to 600mm |
| 7 | Cost for repairing of vertical/flap gate shutter of distributories/branch canal/minor canel/channel including dismantling damaged portion at lower part (skin plate,horizental/vertical gride/stifner etc as per IS:2062-2011/latest revision) not more than 25% of gate hight from bottom by gas cutting and fitting,fixing and fabricated by welding as per direction including cost of materials,machinaries,manpower,cutting,alignment,anchoring,welding,finishing,consumables,carriage and all overheads with all leads and lifts completes as per specification (without painting) |
| 8 | Oiling,Cleaning & greasing the gate parts i.e guide chanel,top runner,pedestal block,gear rods,wheel,fish plate etc.with sufficient lubricant as and when required for the regulator gates of distributories/branch canel/minor canel/channel as per direction of the EIC including cost of all materials to site complete with all lead & lift. |
| 9 | Aligning the pump motor set after necessary adjustment for required matching offaces to the flexible coupling with allowed tollerance. |
| 10 | Supply fitting, fixing of SS nut, bolt & washeri) Length above 75 mm upto 150mm |
| 11 | Supplying and fixing 32A ,415V, TPN SFU openexecution in existing SS enclosure/cubical with nutsbolts etc incl. S & F 3 nos. DIN type HRC fuse asper rating.[Make-L&T or equivalent make]as per direction of EIC |
| 12 | Supply & fixing of 415/440 Volt, HRC fuse(Make: L&T/ Havels/CGL/GE) |
| 13 | for 2-40Amp |
| 14 | for 50- 63 Amp |
| 15 | Supply and fixing of smart bright street light (36 Watt) complete with all accessories to be fixed /projected from the wall of the building or on pole incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. |
| 16 | Added:- @ 18% as GST |
| 17 | Added:- @ 1% as labour cess Please Enable Macros to View BoQ information |
