|
| 1 | Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge. |
| 2 | 10.00 HP |
| 3 | 12.5 HP |
| 4 | 15.00 HP |
| 5 | 17.50 HP |
| 6 | 20.00 HP |
| 7 | SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP) |
| 8 | Connection Plates |
| 9 | up to 10 HP |
| 10 | 10 HP to 20 HP |
| 11 | Cooling Fan |
| 12 | up to 10 HP |
| 13 | 10 HP to 20 HP |
| 14 | GM/SS bush |
| 15 | 10 HP to 20 HP |
| 16 | Mechanical reconditioning of Bearing sheet |
| 17 | 10 HP to 20 HP |
| 18 | Mechanical reconditioning ofImpeller sheet and Key way slot |
| 19 | 10 HP to 20 HP |
| 20 | Oil seal |
| 21 | 10 HP to 20 HP |
| 22 | Labour charge for opening and fitting of pump sets |
| 23 | 10 HP to 20 HP |
| 24 | Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (Including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site. |
| 25 | Above 20.00 HP but upto 25.00 HP |
| 26 | SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) |
| 27 | Connection Plates |
| 28 | 20 HP to 30 HP |
| 29 | Cooling Fan |
| 30 | 20 HP to 30 HP |
| 31 | Fan Cover |
| 32 | 20 HP to 30 HP |
| 33 | G.M./SS Gland Guide Bush |
| 34 | 20 HP to 30 HP |
| 35 | Shaft with Sleeve Chuck Nut |
| 36 | 20 HP to 30 HP |
| 37 | Shaft Chuck Nut |
| 38 | 20 HP to 30 HP |
| 39 | G.M. Neck Ring |
| 40 | 20 HP to 30 HP |
| 41 | Bush Shaft Sleeve of G.M. |
| 42 | 20 HP to 30 HP |
| 43 | G.M. Gland Cover |
| 44 | 20 HP to 30 HP |
| 45 | S.S. Shaft (Non Magnetic) |
| 46 | 20 HP to 30 HP |
| 47 | G.M. Shaft Sleeve Check Nut |
| 48 | 20 HP to 30 HP |
| 49 | M.S. Shaft Check Nut |
| 50 | 5 HP to 20 HP |
| 51 | Cooling pipe set with nozzle & Nut |
| 52 | 5 HP to 20 HP |
| 53 | AIR Cock |
| 54 | 5 HP to 20 HP |
| 55 | JOB WORK FOR REPAIR OF PUMP MOTOR |
| 56 | Bearing Housing (rebuilding, turning & finishing) |
| 57 | 5 HP to 20 HP |
| 58 | Bearing Cap (rebuilding, turning & finishing) |
| 59 | 5 HP to 20 HP |
| 60 | Impeller Reconditioning for all type of Pump |
| 61 | 5 HP to 20 HP |
| 62 | Labour Charges for Dismantling & Assembling of Pump |
| 63 | 5 HP to 20 HP |
| 64 | Coupling with stud and rubber bush |
| 65 | 5 HP to 20 HP |
| 66 | Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge. |
| 67 | Type 14 Nos. set |
| 68 | Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC. |
| 69 | 6305 or equivalent size |
| 70 | 6306 or equivalent size |
| 71 | 6309 or equivalent size |
| 72 | 6312 or equivalent size |
| 73 | Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job |
| 74 | 5 HP to 20 HP |
| 75 | 20 HP to 30 HP |
| 76 | Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job. |
| 77 | 5 HP to 20 HP Please Enable Macros to View BoQ information |
