|
| 1 | Providing and Fixing of Furniture & Fixtures in Faculty Room - SLFJPS at NFSU, Gandhinagar |
| 2 | P & F post laminated Work Top with mounter overall size 1200/1500/1800 /2100 X 750 - 1050 mm as per requirements, made from 34MM HDHMR(16+16) laminated board both side 1mm laminated. All edges are covered by 2 mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. MS Brackets are provided to mount with Partition or Gable end. KD fitting: Entire table is assembled through 8mmX45mm concealed bolt with 15mm eccentric cranks, 8mm wooden dowels, etc. Complete drilling and boring work is done on Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. (Refer Sr. No:1 of specifications of tender document for measurements) |
| 3 | P & F post laminated Work Top with mounter overall size 1200/1500/1800 /2100 X 750 - 1050 mm as per requirements, made from 34MM HDHMR(16+16) laminated board both side 1mm laminated. All edges are covered by 2 mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. MS Brackets are provided to mount with Partition or Gable end. KD fitting: Entire table is assembled through 8mmX45mm concealed bolt with 15mm eccentric cranks, 8mm wooden dowels, etc. Complete drilling and boring work is done on Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. (Refer Sr. No:1 of specifications of tender document for measurements) |
| 4 | P & F post laminated Work Top with mounter overall size 1200/1500/1800 /2100 X 750 - 1050 mm as per requirements, made from 34MM HDHMR(16+16) laminated board both side 1mm laminated. All edges are covered by 2 mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. MS Brackets are provided to mount with Partition or Gable end. KD fitting: Entire table is assembled through 8mmX45mm concealed bolt with 15mm eccentric cranks, 8mm wooden dowels, etc. Complete drilling and boring work is done on Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. (Refer Sr. No. 1 of specifications of tender document for measurements) |
| 5 | Gable End 800-700X710X34 mm (LEG) : P & F Gable end to support top having overall size 800-700/710/34mm. 34mm pre laminated/post laminated Plywood Panels of 16+16 mm BWR calibrated ply confirming to IS 303 covered with lamination in both sides, glued with PUR glue. All edges are covered with 2mm thick PVC edge bands. (Refer Sr. No. 2 of specifications of tender document for measurements) |
| 6 | Pre fabricated KD Panels: Providing and Fixing Pre fabricated Plywood KD panels : Pre Laminated/Post laminated Plywood, 16mm thick BWR calibrated ply confirming to IS 303 covered with lamination, on both sides, . All the edges are covered with matching 2/0.8mm thick PVC edge bands glued with hot melt glue on CNC controlled through feed edge banding machine with pre milling operation. KD fitting: Entire unit is assembled through 8mmX45mm concealed bolt with 15 m eccentric cranks, 8mm wooden dowels, etc. complete drilling and boring work is done on CNC Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. (Refer Sr. No. 3 of specifications of tender document for measurements) |
| 7 | Pre fabricated KD Panels: Providing and Fixing Pre fabricated Plywood KD panels : Pre Laminated/Post laminated Plywood, 16mm thick BWR calibrated ply confirming to IS 303 covered with lamination, on both sides, . All the edges are covered with matching 2/0.8mm thick PVC edge bands glued with hot melt glue on CNC controlled through feed edge banding machine with pre milling operation. KD fitting: Entire unit is assembled through 8mmX45mm concealed bolt with 15 m eccentric cranks, 8mm wooden dowels, etc. complete drilling and boring work is done on CNC Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. (Refer Sr. No. 3 of specifications of tender document for measurements) |
| 8 | Providing storage rack ready to assemble type, self-standing, over hanging or partition mounted storage system having 450 mm. Ready to assemble type, Self-standing storage unit having depth 450mm as per requirements with following details: Carcass and shelves: Made from 18mm pre laminated MDF Panels covered with 0.8 mm laminate on both side glued with PUR glue, 0.8mm thick PVC edge bands glued with hot melt Glues on auto edge banding machine. All panels should be interchangeable to facilitate assembly at site. The shelves are connected with body through adjustable shelf supports. Back Panel: 3mm high pressure compact sheet both side laminated hold in slit formed in the body. Shutters: Made from Pre-laminated MDF Panels covered with laminate on both side glued with PUR glue, with 2 mm thick PVC edge bands glued with hot melts Glues on auto edge banding machine with pre milling attachment, Hinged with concealed auto clip-on system \\"Blum\\", \\"Grass\\" or \\"Hettich\\" make OR top sliding mechanism with25 x 25 mm aluminium extruded channels and Top mounted laterally guided ball bearing blocks. KD fittings: 8 mm x 45 mm concealed bolt with 15 mm eccentric cranks, 8 mm jute dowels, 75 x 50 mm M.S. brackets, etc. complete. Drilling and boring work is done on Multi drill machine in KD-32 system. All mounting holes are notched in all axis simultaneously in single reference. The maximum span between two adjacent holes should not be more than 96 mm. (Refer Sr. No. 4 of specifications of tender document for measurements) |
| 9 | Providing storage rack ready to assemble type, self-standing, over hanging or partition mounted storage system having 450 mm. Ready to assemble type, Self-standing storage unit having depth 450mm as per requirements with following details: Carcass and shelves: Made from 18mm pre laminated MDF Panels covered with 0.8 mm laminate on both side glued with PUR glue, 0.8mm thick PVC edge bands glued with hot melt Glues on auto edge banding machine. All panels should be interchangeable to facilitate assembly at site. The shelves are connected with body through adjustable shelf supports. Back Panel: 3mm high pressure compact sheet both side laminated hold in slit formed in the body. Shutters: Made from Pre-laminated MDF Panels covered with laminate on both side glued with PUR glue, with 2 mm thick PVC edge bands glued with hot melts Glues on auto edge banding machine with pre milling attachment, Hinged with concealed auto clip-on system \\"Blum\\", \\"Grass\\" or \\"Hettich\\" make OR top sliding mechanism with25 x 25 mm aluminium extruded channels and Top mounted laterally guided ball bearing blocks. KD fittings: 8 mm x 45 mm concealed bolt with 15 mm eccentric cranks, 8 mm jute dowels, 75 x 50 mm M.S. brackets, etc. complete. Drilling and boring work is done on Multi drill machine in KD-32 system. All mounting holes are notched in all axis simultaneously in single reference. The maximum span between two adjacent holes should not be more than 96 mm. (Refer Sr. No. 4 of specifications of tender document for measurements) |
| 10 | Providing storage rack ready to assemble type, self-standing, over hanging or partition mounted storage system having 450 mm. Ready to assemble type, Self-standing storage unit having depth 450mm as per requirements with following details: Carcass and shelves: Made from 18mm pre laminated MDF Panels covered with 0.8 mm laminate on both side glued with PUR glue, 0.8mm thick PVC edge bands glued with hot melt Glues on auto edge banding machine. All panels should be interchangeable to facilitate assembly at site. The shelves are connected with body through adjustable shelf supports. Back Panel: 3mm high pressure compact sheet both side laminated hold in slit formed in the body. Shutters: Made from Pre-laminated MDF Panels covered with laminate on both side glued with PUR glue, with 2 mm thick PVC edge bands glued with hot melts Glues on auto edge banding machine with pre milling attachment, Hinged with concealed auto clip-on system \\"Blum\\", \\"Grass\\" or \\"Hettich\\" make OR top sliding mechanism with25 x 25 mm aluminium extruded channels and Top mounted laterally guided ball bearing blocks. KD fittings: 8 mm x 45 mm concealed bolt with 15 mm eccentric cranks, 8 mm jute dowels, 75 x 50 mm M.S. brackets, etc. complete. Drilling and boring work is done on Multi drill machine in KD-32 system. All mounting holes are notched in all axis simultaneously in single reference. The maximum span between two adjacent holes should not be more than 96 mm. (Refer Sr. No. 4 of specifications of tender document for measurements) |
| 11 | Providing Medium Back revolving & tilting executive chair, as per approved sample by chief architect/project in charge, with PU. Handle, hot pressed bend ply in seat and back, ergonomically design with natural shape of spine supporting entire back of the user and provide good lumber support. The back rest ht is 26\\" Upholstered with 40 density PU foam in seat and back, covered with approved tapestry of matty quality. Bottom: 38mm dia x 1.6 mm thick pipe used in five prone stand with castors, Single position lock, gas lift operating system and tilt mechanism made from M.S. sheet [2.5, 3.15, 4mm thickness], duly powder coated 40 to 50 micron. (Refer Sr. No.5 of specifications of tender document for measurements) |
| 12 | Centre Table: Providing and fixing glass top rectangular top centre table as per the drawing. It shall have overall size 900mm(W)x600mm(D)x400mm(H). The under structure of the table shall be made of BWR calibrated ply confirming to IS 303 covered with 1mm lamination with wooden texture and water proof paper. Top glass shall be 10mm thick. The accessories used in the table shall be metal alloy and stainless steel complete as per design, drawing and as per specifications / additional specifications & as directed by Engineer-in-Charge. (Refer Sr. No.6 of specifications of tender document for measurements) |
| 13 | Classroom 2 seater DESK: Providing and fixing seater bench and desk unit for class rooms. Desk top size 1400/1500X400x/350X34mm. and Gable ends on both ends 800X400X34 mm and Outer modesty panel 1400/1500X250X34 mm, made from 34mm thick pre laminated Plywood made from 16+16 mm Calibrated BWR plywood confirming to IS 303, both side 0.8 mm laminated with PUR/D3 glued on auto spreader and pressing. Inner Modesty Panel 400 wide, Shelf 200mm wide made from 18 mm pre laminated/post laminated calibrated BWR plywood panel. All edges are covered by 2/0.8 mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. KD fitting: Entire table is assembled through 8mmX45mm concealed bolt with 15mm eccentric cranks, 8mm wooden dowels, etc. Complete drilling and boring work are done on Multi drill machine in KD – 32 System. All mounting holes are notched in all axis simultaneously in single reference. Complete interchange ability is required in all parts. Seating TIP-UP BENCH: Tip-Up type 2 seater Group Bench – 1400/1500 mm long : made from MS box section 60X40X1.6mm as central spine beam, supported on T legs of MS capsule 70X30X1.6mm. Seat ad measuring 450X400X50mm made from 25X25X1.6mm MS Box section with Tip-Up mechanism made from 2.5mm MS sheet, Back rest 450X350X30mm is made from 19mm round MS tube. All M.S. components are powder coated in 7 tank process with PU powder in required shade. Seat and back are provided with 50mm and 30mm PU cushion upholstered with leatherier (Refer Sr. No. 7 of specifications of tender document for measurements) Please Enable Macros to View BoQ information |
