|
| 1 | Demolishing cemant concrete manually by machinecal means including disposal of material within 50 mitres road as per diraction on engineer-in- charge. nominal concrete1:3:6 or richer mix (i/c equivalent design mix) |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 20 mm nominal size) |
| 3 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). |
| 4 | separation membrane of impermeable plastic sheeting 125 micron thick |
| 5 | providing and laying dense graded Bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading. Premixed with bituminous binder @4.5 percent by weight of total mix and filler, transporting the hot mix to work site, laying with Hydrostatic paver finisher with sensor contral to the required grade. level and alignment, rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction and density compaction as per MORTH specification, clause No.505 comlete in all respects. |
| 6 | Providing and applying tack coat using hot straight run bitumen of grade 80/100, On bituminous surface @ 0.50 Kg / sqm |
| 7 | Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading. Premixed with bituminous binder @5.4 percent of mix and filler, transporting the hot mix to work site, laying with Hydrostatic paver finisher with sensor contral to the required grade. level and alignment, rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction and density compaction as per MORTH specification, clause No.507 comlete in all respects. |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 100 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 9 | 12 mm cement plaster :1:4 (1 cement : 4 coarse sand) |
| 10 | Neat cement punning |
| 11 | Fabrication & Manufacturing of Prestressed Hollow Core slab (Hollow area 25 to 30%) of different thickness & modular width 1200 mm in Controlled Factory Environment with approved methodology informing to IS 10297- 1982 conforming to IS : 10297- 1982 by using long line casting method having rrangement of proper steel bed. Concreting should be done by batch mixing plant capable of producing zero slump concrete, transported through automatic shuttels of standard make & layed on bed with the help of xtruder/Slipformer, finishing, curing and also provision of steam curing. Cutting, making necessary cutout/holes of required sizes for services in slab element after achieving required strength, yard handling & stacking all complete as per approved shop drawings & design mix as per the direction of the Engineer-in-charge. (Cost of strands should be paid separately). Note : Excess/ less cement over the specified cement content used as per design mix is payable / recoverable separately. Concrete Grade-M-40 (cement content 400 kg ) 150 mm thick hollow core slab |
| 12 | Providing and laying 80 mm thick factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. |
| 13 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and irection of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage Please Enable Macros to View BoQ information |
