|
| 1 | Providing and replacing of kirloskar make new HSC Bare shaft pump model UP 150/38 of standard fitted construction coupled directly through a set of flexible coupling (tyre type) on a common fabricated MS base frame, replace the tapers and flanges of required size including dismantling of existing pump, installation of new pump with new base frame, coupling, labour charges cartage, Nut Bolt/Fasteners and commisioning etc. complete as per direction and entire satisfaction of Engineer-in-Charge. |
| 2 | Providing and replacing of squirrel-cage horizontal electric induction motorvof 60 HP operated on 3 phase , 415+/- 10% volts, AC supply with ambient 50+/- 5% cycles AC supply at 1450 RPM totally enclosed fan cooled squirel casge enclosure confirming to protection IP 55% Horizontal foot mounted (B3),class B insulation with temperature rise to class B including dismantling and removing existing motor and fixing the new induction motor on the same base-plate, making proper alignment with the centrifugal pump , fixing new flexible tyre and coupling,making connection, providing nuts & bolts, thimbles etc. complete (if any) including testing, commissioning complete as per direction and satisfaction of Engineer in charge. |
| 3 | Providing and replacing kirloskar make new DV-50 CS vacuum complete pumpset, 10 HP, Three phase, 415 volts size 50 mmx 50 mm of standard fitted construction coupled directly through a set of flexible coupling (tyre type) on a common fabricated MS base frame including dismantling of existing pump, installation of new pump with new base frame, coupling, labour charges cartage, Nut Bolt/Fasteners and commisioning etc. complete as per direction and entire satisfaction of Engineer-in-Charge. |
| 4 | Providing & replacing 1.5 HP ETERNA 1100 CW dewatering pump, size 50 mm of kirlosker make suitable for operation on three phase with heavy duty self priming voltage fluctuations range 415 volts etc. complete as per direction and satisfaction of engineer-in-charge. |
| 5 | Providing and replacing B C H/L& T make Air Break Push Button operated fully automatic citation star-delta starter (Cat. No. NASACT2LEEM) comprising of three Nos. citation E contactors (70 Amps), one No. over load relay (Relay range: 37.60 - 60.00Amps), and one No. pneumatic timer suitable for operation on 400/ 440 volt, 3 phase, 50 Hz A C supply in sheet steel enclosure including providing and fixing required copper thimbles, making electrical and earth connections, also mounting the starter on existing M.S frame including testing and commissioning etc. complete as per the satisfaction of engineer in charge. |
| 6 | Providing and replacing B C H/ L& T make Air Break Push Button operated fully automatic citation star-delta starter (Cat. No. NASAMLEN ) comprising of three Nos. citation N0N contactors (25 Amps), one No. over load relay (Relay range: 17.4- 24.00Amps), and one No. pneumatic timer suitable for operation on 400/ 440 volt, 3 phase, 50 Hz A C supply in sheet steel enclosure including providing and fixing required copper thimbles, making electrical and earth connections, also mounting the starter on M.S frame including testing and commissioning etc. complete as per the satisfaction of engineer in charge. |
| 7 | Providing and replacing B C H/ L& T make Air Break Push Button operated fully automatic citation submerssible pump star-delta starter (Cat. No. CPPYNAMN ) comprising of three Nos. citation N0N contactors (25 Amps), one No. over load relay (Relay range: 17.4-24.0 Amps) including providing and fixing required copper thimbles, making electrical and earth connections, also mounting the starter on M.S frame including testing and commissioning etc. complete as per the satisfaction of engineer in charge. |
| 8 | Providing / laying & fixing 250 mm dia ( Prakash Surya/Tata/Jindle Make 9.5 mm thick) M.S. Pipes/bends/tapper/ mechnical specials such Conforming to IS:3589-2001 (Grade- 330) of required dia, thickness inculding dismantling exisitng pipes, bends, tapper,nuts,bolts, carriage, loading, unloading, cutting, in desired shape as per site requirement (Nothing extra will be paid for making required shape bend etc ) and complete satisfaction of Engineer-in-Charge. |
| 9 | Providing and fixing 250 mm dia MS flange 16 mm thick of required size as per direction and satisfaction of Engineer-in-charge. |
| 10 | Providing & replacing Schneider/L&T (DN3-400M) CM94516OOROOG make 400 amps. Triple pole Moulded Case Circuit Breaker(MCCBs for Motor back-up Protection) suitable for fixing at the main panel board incomer , including cost of labour charges for dismantling of existing & Providing/installation of new mccb and including providing & fixing copper thimbles , bus bar / cable , Aluminium links , strips ( as required at site),spreader terminals testing and commissioning etc.Complete as per direction and satisfaction of engineer-in-charge |
| 11 | Providing & replacing Schneider/L&T (DN2-250M) CM92171OOPOOG make 250 amps. Triple pole Moulded Case Circuit Breaker(MCCBs for Motor back-up Protection) suitable for fixing at the main panel board incomer , including cost of labour charges for dismantling of existing & Providing/installation of new mccb and including providing & fixing copper thimbles , bus bar / cable , Aluminium links , strips ( as required at site),spreader terminals testing and commissioning etc.Complete as per direction and satisfaction of engineer-in-charge |
| 12 | Supplying and fixing Finolex/National/kalinga Gold make 70 mm² P.V.C Innersheathed armoured 3 core A2XWY/A2XFY aluminium conductor cable suitable for voltage grade up to 1100V complete with thimbles connectors Insulating tapes, glaned of required size etc. as required for making connection from change over switch to air circuit breaker.Complete as per direction and satisfaction of engineer-in-charge. |
| 13 | Supplying Finolex/Havells/kalinga Gold make 50 mm² P.V.C Insulated unsheathed single core Armoured 2XWaY/2XFaY copper conductor flexible cable suitable for voltage grade up to 1100V complete with thimbles connectors Insulating tapes, glaned of required size etc. as required for making connection from starter to motor.Complete as per direction and satisfaction of engineer-in-charge. |
| 14 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Please Enable Macros to View BoQ information |
