Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | PART -A: CIVIL WORKS |
| 2 | Excavating trenches of required width for pipes, cables etc including excavation for sockets & dressing of sides, ramming of bottoms,depth upto 1.5m including taking out excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing surplus excavated soil as directed, within or outside site at unobjectionable place in all kinds of soil |
| 3 | i) Pipes,cables etc. not exceeding 80mm dia |
| 4 | iv) Pipes, Cable etc. > 80mm < 300m dia |
| 5 | v) For extra depth of >1.5m < 3m for dia 80 to 300mm |
| 6 | vi) For extra depth of >3m < 4.5m for dia 80 to 300mm |
| 7 | Supply & filling of local earth (including royalty) by mechanical transport also including ramming & watering of the earth in layers not exceeding 20cm in depth in plot, trenches, plinth, sides of foundations etc. complete |
| 8 | Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of attached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming including watering, consolidating and dressing complete. |
| 9 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees & saplings of girth upto 30cm measured at a height of 1m above ground level and removal of rubbish outside the site and to an unobjectionable place. |
| 10 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size). Item includes providing & mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specifications. Providing & applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes & finally with a piece of cloth lightly soaked in kerosene oil |
| 11 | Painting top of roofs with residual type petroleum bitumen of grade VG10 of approved quality at 17kg per10sqm impregnated with a coat of coarse sand at 60 cudm per 10sqm including cleaning the slab surface with brushes & finally with a piece of cloth lightly soaked in kerosene oil complete. |
| 12 | Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in position and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete. |
| 13 | ii) Hot finished seamless type tubes |
| 14 | Providing and fixing stainless steel (SS 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of the waist slab with suitable arrangement, all complete as per specification and direction of Engineer-in-charge. |
| 15 | 25mm Thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 16 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand)jointed with grey cement slurry mixed with pigment to match the shade of the slabs,including rubbing and polishing complete. |
| 17 | Providing & fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (minimum thickness of 5 mm) of approved make in all colours,shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting,risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade. |
| 18 | Providing & laying vitrified floor tile Matt/Antiskid finish in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sand jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified by Engineer-in-charge. |
| 19 | iii) Flooring with size of Tiles 80x80Cm in cement mortar 1:4 |
| 20 | Providing & laying vitrified floor tile in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sand jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified |
| 21 | ii) Flooring with size of Tiles 80x80Cm in cement mortar 1:4 |
| 22 | Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Tiles of dark shade pigment using ordinary cement |
| 23 | Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge. |
| 24 | ii) Granite work |
| 25 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels. |
| 26 | iii) Granite of any colour and shade having Area of slab upto 0.50 sqm |
| 27 | iv) Granite of any colour and shade having Area of slab over 0.50 sqm |
| 28 | 40mm Thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand:4 stone aggregate of 20mm nominal size) finished with a floating cement coat of neat including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 29 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately). |
| 30 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 31 | ii) With float glass panes of 5.0 mm thickness (weight not less than 12.5kg/sqm) |
| 32 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 33 | i) With stainless steel cover plate minimum 1.25 mm thickness |
| 34 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 35 | Providing wood work in frames of doors, windows, clerestory windows & other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length |
| 36 | iii) Kiln seasoned and chemically treated Hollock wood |
| 37 | Providing & fixing ISI mark flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains/cross bands & face veneers on both faces of shutters |
| 38 | ii) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 39 | Providing and applying plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 40 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture |
| 41 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture |
| 42 | Providing & fixing chrome plated brass100mm mortise latch with one dead bolt with 6 levers & a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 43 | Providing and fixing 150 mm bright finished chrome plated brass hanging type floor door stopper with rubber cushion necessary brass screws, etc. complete. to suit shutter thickness complete |
| 44 | Providing and fixing 100x85x5.5 mm (heavy type) bright finished brass butt hinges with necessary screws etc. complete : |
| 45 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 46 | Providing & fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : |
| 47 | i) 200x10 mm |
| 48 | ii) 100x10 mm |
| 49 | Providing & laying water proofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment & sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 50 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth within premises |
| 51 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mixer plant at Optimum Moisture Content, carriage of mixed material by tippers to work site, for all lead and lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface & compacting with vibratory power roller to achieve the desired density, complete as per specification & direction of Engineer-in-charge. |
| 52 | i) With material confirming to grade-I (size 75 mm to .075 mm) having CBR value - 30, Thickness as desired |
| 53 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to .075 mm) to wet mix macadam (WMM) specifications including premixing the material with water at OMC for all leads and lifts, laying in uniform layers with mechanical paver finisher in sub-base/base course on well prepared surface and compacting with vibratory roller of 8 to 10 ton capacity to achieve the desired density, complete as per specifications & directions of Engineer-in- charge |
| 54 | Providing and applying tack coat using hot straight run bitumen of grade VG-10 including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : |
| 55 | i) On W.B.M. @ 0.75 Kg / sqm. |
| 56 | ii) On bituminous surface @ 0.50 Kg / sqm. |
| 57 | Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade including required key aggregate as specified spreading coarse aggregate with the help of self propelled/ tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : |
| 58 | i) For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG-10 @ 50 kg/10 sqm. |
| 59 | 2.5 cm Premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2mm and 11.2mm size respectively per 100 sqm. and 52 kg. and 56 kg. of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete. (tack coat to be paid for separately) : |
| 60 | i) With paving Asphalt grade VG-10, heated and then mixed with solvent at the rate of 70 grams per kg of asphalt. |
| 61 | Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road roller all complete. |
| 62 | Supply, fitting, and fixing stainless steel (304 grade) door hardware fittings including necessary stainless steel screws, glues, and all labour etc for the following items# |
| 63 | 25 mm dia, 300 mm long SS of H/D type pull handle.(Similar to Godrej Product No-7267) |
| 64 | SS D Type Handle in Pair 125 mm long 19mm dia.(Similar to Godrej Product No-1064) |
| 65 | SS H Type Handle 155x12mm (Similar to Godrej Product No-8400) |
| 66 | SS Twin rubber Door Stopper in Satin Steel finish with 95mm length, 7mm Dia and rubber base. Positive stop at fixed angles. Complete set including the fixing accessories.(Similar to Godrej Product No-8565). |
| 67 | Locking arrangement in between Glass to glass for frameless glass door.(Similar to Godrej Product No-7780). |
| 68 | SS304 square tower bolt with 25mm projection and Dia 10mm bolt. L=150mm in Satin Finish. Complete set including the fixing accessories.(Similar to Godrej Product No-8569). |
| 69 | Providing & fixing IS : 3564 marked Alumunium die cast body tubular type universal hydraulic door closer with with standard arm with two independent closing valves and latching speed adjustable by arm. Non handed installation. Max Door width 1100mm, Max Door weight 80 Kg, Max opening angle 180deg. Transom mounting available and Parallel arm (optional). Silver finish. As per EN 1154, EN 1634 and CE marked. 2-Hour Fire Rated with BS 476 : PART 20 & 22 & IS 3614 : PART 2 certified. Complete set including the fixing accessories and screws etc.complete.(Similar to Godrej Product No-8156) |
| 70 | Supply, drilling in RCC and fixing of metallic anchor fasteners for supporting of cable trays and miscellaneous electrical switchgear of following sizes, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 71 | 3/16\\" BSW. |
| 72 | 5/16\\" BSW. |
| 73 | 1/4\\" BSW. |
| 74 | 3/8\\" BSW. |
| 75 | 5/8\\" BSW. |
| 76 | 1/2\\" BSW. |
| 77 | Supplying, assembling and installing 1000 mm high satin finish stainless steel (SS 304 grade) tubular railing of approved design in staircases, ramps, around floor cut outs etc. consisting of: 1. 50mm dia SS pipe top handrail 2. 32 mm dia SS pipe balusters (at every third step for staircase, @ maximum 1200mm c/c for ramp, floor cutouts) 3. 3 nos minimum 18mm dia SS pipe intermediate handrails. Including: 1. Fixing balusters to floor with 4 nos bolts änd 8mm thick, 100mm dia SS base plate & SS cap/collar. 2. Fixing top handrail to the balusters with 12mm dia SS bar connector & 6mm thick SS saddle plate. 3. Fixing intermediate handrails to the balusters with 12mm dia SS bar connector. 4. All end caps, decorative caps over balustrades,necessary bending, welding, polishing of all welded joints (Length of top handrail shall be measured for payment). |
| 78 | Providing, supplying and installing at site GRC Jallis (Grills), made up of mainly White Cement (conforming to ASTM C 150), High Silica sand (conforming to ASTM c144), AR Glasfibre, Admixtuers (conforming to ASTM c260,ASTM c618), by using Vibration Cast Premix Process and as recommended by PCI (Precast Institute) USA, Manual 128 (edn4) or as per GRCA International specifications including supporting GI base frame work of appropratie sizes ensuring stability with design as per details provided in drawings and site requirements/ measurements and as per approved finish and color shade, with sealers and hardwares required, all in accordance with the manufacturer' specifications and conforming to Indian/ ASTM standards, along with submission of shop drawings for approval, complete in all respects. |
| 79 | Providing and laying of approved INTERLOCK PAVERS (rough finish with solar reflectance index value higher than 0.5, size 100x200x80mm or as/ design) in road and parking area bands, laid over 100mm thick sand base over well compacted subbase/ WBM and mortar with joints filled in fine sand as per manufactured requirements etc. all complete. |
| 80 | Providing, supplying and installing at site Glass Reinforced Concrete (GRC) Claddings, made up of mainly White Cement (conforming to ASTM C 150), High Silica sand (conforming to ASTM c144), AR Glassfibre, Admixtuers (conforming to ASTM c260,ASTM c618), by using Spray Process and as recommended by PCI (Precast Institute) USA, Manual 128 (edn4) or as per GRCA International specifications with design as per details provided in drawings and site requirements/ measurements and as per approved finish and color shade, with sealers and hardwares required, all in accordance with the manufacturer's specifications and conforming to Indian/ ASTM standards, along with submission of shop drawings for approval, complete in all respects. |
| 81 | Providing and laying av. 80 mm thick cement concrete grass paver block of approved shade and design to be laid as per manufacturer specifications and including 50mm thick compacted bed of course sand, all materials and labour as per direction of Owner/Architects. |
| 82 | Providing & fixing in position aluminium sliding windows with sliding aluminium shutters (for 2/3/4 tracks), 15 micron approved finish fully glazed as per Jindal or equivalent section and as per overall sizes given in drawing & having outer frame made out of aluminium tube sections weighing 1.2 kg/m or Heaviest and sliding shutters having bottom track weighing 1.23 kg/m or Heaviest, vertical / top weighing 0.98 kg/m or Heaviest, shutter interlock weighing 0.49 kg/m or Heaviest & shutter top & bottom weighing 0.4 kg/m or Heaviest along with all standard accessories such as PVC gaskets, weathering imported bearing, concealed type locking arrangement, handles etc. and float glass of 4mm thickness etc. complete. Including sealing joints with approved sealing material with masonry opening surface to make it waterproof. |
| 83 | PARTLY FIXED - PARTLY LOUVERS WINDOW ANODIZED FOR TOILETS (Tentative size: 2'0\\"x 1'6\\" ): Provide and Fixing aluminum partly fixed adjustable louver (Anodized) made out of 2\\" X 1 1/2\\" X 1.6 mm Aluminium Tubular Sections alround, center along with 4nos. of 5.5mm thick 4\\" wide textured glass louvers including louvers frame along with 5.5mm thick shelf design textured glass fixed with 12mm X 12mm X 1.5mm thk aluminum square beading, scaffolding, carting away debris out of compound, cleaning the site etc complete as per site requirements and the instructions of Architect/EIC. Mode Of Measurement - Length X Width |
| 84 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (i) For 10 users A) With Pakur variety. (SAIL/TATA/RINL) |
| 85 | Laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : - 500mm dia. Pipes shall be free issue material. Cost of Transportation of pipe including all tools and tackles for loading and shifting from store to execution location shall be in the scope of contractor. No extra Claim for transportation shall be paid. |
| 86 | Laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : - 450mm dia. Pipes shall be free issue material. Cost of Transportation of pipe including all tools and tackles for loading and shifting from store to execution location shall be in the scope of contractor. No extra Claim for transportation shall be paid. |
| 87 | Supplying and laying 50mm thick concrete screed of M 15 grade to be laid over waterproofing treatment as per drawing & direction of Engineer-in-charge including cost of all materials & labour. |
| 88 | Supply and application of 3 coats of food grade, similar to Sika Guard 67 to the inside wall & floor of water reservoir, over smooth cement finished surface complete with all materials and labour. The work shall be executed as per manufacturer specification. |
| 89 | i) All kinds of Soil |
| 90 | i) Local Fine Sand within grading zone IV |
| 91 | Supply of Chlorpyriphos/Lindane |
| 92 | Diluting and inject chemical emulsion |
| 93 | Along external wall below Con/masonry |
| 94 | Soil Treatment under existing floor |
| 95 | Treatment of existing masonry |
| 96 | Treatment at point of contact-wood |
| 97 | vi) 1:3:6(1 Cement : 3 Coarse Sand : 6 Graded stone aggregate of 40mm) |
| 98 | ix) 1:4:8(1 Cement :4 Fine Sand : 8 Graded stone aggregate of 40mm) |
| 99 | i) Foundations,footings,bases of column |
| 100 | i) Foundations,footings,bases of columns, etc. for mass concrete |
| 101 | iii) Suspended floors,roofs,landings,balconies, access platform and Shelves (Cast in situ) |
| 102 | v) Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 103 | ii) Walls (any thickness) including attached pilasters, buttress, plinth and string courses etc. |
| 104 | ii) M25 RMC for All works ABOVE PLINTH UPTO FLOOR 5 LEVEL |
| 105 | ii) Brick work in Cement mortar 1:6 (1 cement: 6 coarse sand ) IN FOUNDATION AND PLINTH |
| 106 | AAC Block masonry-150/200/250mm tk-SS |
| 107 | 100mm tk AAC Block in Super Structure |
| 108 | Flame finish granite stone flooring |
| 109 | 30mm tk granite on footpath etc,< 0.5sqm |
| 110 | Design, fab. etc of Structural Glazing |
| 111 | Glazing in fire resistant door shutter |
| 112 | ii)12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand) |
| 113 | iv) 15mm Cement plaster of mix 1:6 (1 cement: 6 fine sand) on rough side of half or single brick wall |
| 114 | Providing Neat cement punning |
| 115 | Finishing walls with Deluxe Multi surface paint system for interiors & exteriors using Primer as per manufacturers specifications with two or more coats applied on wall @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm |
| 116 | Providing & fixing O shape SS Handle |
| 117 | Fibre reinf elastomeric membrane |
| 118 | i) 1:3:6 or richer mix (i/c equivalent design mix) |
| 119 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars & disposal of unserviceable material outside site to an unobjectionable place as/ direction of Engineer-in-charge |
| 120 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. |
| 121 | i) Of area 3 sq. metres and below |
| 122 | Providing and laying in position approved quality profiled, pre-coated coloured galvanized steel sheets of 0.55mm thickness (TCT) in barricading, including cost of all materials, delivery to site, cutting, metering, lapping, providing cut-outs for fixing accessories and necessary approved quality corrosion proof fasteners with neoprene capping and washers ridges, valleys, gutters, gutters of required shape, apron pieces, flashing etc. all complete and with all accessories required for the cladding works including necessary scaffolding for erection jobs and as shown on drawings, specified and directed. NOTE: (1) Contractor shall take back the cladding sheets (used in barricading structure) after completion of the job and on the instructions of Engineer-in-Charge. (Cost of dismantling and Carriage till contractor's store (outside the IOCL premises) is included in this item and no extra payment shall be paid to the contractor on this account). (2) Payment against the job on SQM basis shall be made to the Contractor while erection of the cladding sheets(3) The cladding sheets shall be dismantled and taken outside the Refinery premises by the Contractor within 30 days of instructions from E-i-C. (4) In case the Contractor fails to dismantle and shift the cladding material outside the IOCL premises within 30 days of clear instructions from E-i-C, the Owner shall be free to get the same dismantled and shift to Owner's scrap yard using Owner's resources and in such case the dismantled items shall not be returned to the Contractor and the ownership of the same shall be fully vested with the Owner (5) Contractor shall note that all the Safety stipulations of the Contract including the Safety Penalties shall be applicable while dismantling the barricading structure. |
| 123 | Expansion Hold fasteners in RCC/CC etc |
| 124 | Fastener with threaded dia 6 mm. |
| 125 | Fastener with threaded dia 6 mm. |
| 126 | Fastener with threaded dia 10 mm. |
| 127 | 10mm tk acid/alkali resisting tiles |
| 128 | In flooring |
| 129 | In dado/skirting |
| 130 | Prov & grout dowel rubes/shear keys etc |
| 131 | PART -B : SANITARY & PLUMBING WORKS |
| 132 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P.flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 133 | i) W.C. pan with ISI marked white solid plastic seat and lid |
| 134 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 135 | i) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 136 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 137 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 138 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required, Kitchen Sink with Drain board |
| 139 | i) Sink with drain board 510x1040mm bowl depth 250mm |
| 140 | Providing and fixing C.P. brass stop cock (concealed) of standard design & of approved make conforming to IS:8931 - 15 mm nominal bore. |
| 141 | Providing and fixing of Automatic Soap/ Sanitizer Dispenser with all fittings and all complete, as per specification and direction of Engineer-in-charge. |
| 142 | Providing and fixing 450 mm long CP Brass towel rail complete with brackets fixed to wooden/PVC cleats with SS screws with concealed fittings arrangement of Make: Cera F5007104 or equivalent all complete and as per direction of Engineer-in-charge. |
| 143 | Providing and fixing 600x120x5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets & guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 144 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms - 15 mm nominal bore. |
| 145 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes. |
| 146 | ii) 110 mm diameter |
| 147 | Providing and fixing Chrome Finish SS Health faucet with 8mm dia, 1 meter long SS braided rubber hose pipe and wall hook with N.R.V, Jaguar make cat. No. ALD-577 or equivalent all complete, as per specification and direction of Engineer-in-charge. |
| 148 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: |
| 149 | i) Inside dimensions 455x610mm and 45cm deep for single pipeline with common burnt clay FPS (non modular) bricks of class designation 7.5 |
| 150 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 151 | i) 15 mm nominal outer dia Pipes |
| 152 | ii) 20 mm nominal outer dia Pipes |
| 153 | iii) 25 mm nominal outer dia Pipes |
| 154 | v) 40 mm nominal outer dia Pipes |
| 155 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. |
| 156 | i) 15 mm nominal outer dia Pipes |
| 157 | ii) 20 mm nominal outer dia Pipes |
| 158 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 159 | i) 25 mm nominal bore |
| 160 | ii) 32 mm nominal bore. |
| 161 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 162 | ii) 150 mm diameter |
| 163 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and SW drain pipe 100 mm diameter, 1.8 m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 164 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : |
| 165 | ii) 150 mm diameter |
| 166 | Supplying and fixing C.I. cover without frame for manholes : |
| 167 | iii) 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg. |
| 168 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: |
| 169 | i) 100 mm diameter S.W. pipe |
| 170 | Providing and fixing soil, waste and vent pipes : |
| 171 | i) 100mm dia Sand cast iron S&S pipe as per IS: 1729. |
| 172 | Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. |
| 173 | ii) 110mm Coupler |
| 174 | vi) Single tee with door of 110x110x110 mm |
| 175 | viii) Single tee without door of110x110x110 mm |
| 176 | x) 87.5° Bend of 110 mm |
| 177 | xii) Shoe (Plain) of 110 mm |
| 178 | Providing & fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work & fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 179 | ii) 110 mm |
| 180 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 181 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : |
| 182 | i) 100x100 mm size P type with common burnt clay bricks of class Designation 7.5 |
| 183 | Providing and fixing 15mm nominal bore C.P brass \\"Pressmatic\\" pillar cock with auto closing system for wash basins of Jaquar make(Model-PRS-031). |
| 184 | Urinal Valve auto closing system of Jaquar PRS-077 |
| 185 | Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed. - 50 Users |
| 186 | Providing & fixing 6mm thick, copper back finish, looking mirror of required size, made of float sheet glass of best quality & approved make, approved design & shape, over 12mm thick marine board fixed to rawl plug with round head screws & washers including teakwood beading with melamine polish all around, complete in all respects inclusive of cost of all materials, labour, tools, tackles etc. as per specifications and directions of the Engineer-in-Charge. |
| 187 | Providing and fixing urinal partition with frosted safety glass of 8mm thick of size 900mm(height) x 450 mm(width) corner chamfered fixed in brick wall with stainless steel clips of grade 304 all complete. |
| 188 | CP/SS Jet - 8mm - 1m flexible tube |
| 189 | PTMT bottle trap for wash basin and sink |
| 190 | Single piece 38 mm bottle trap |
| 191 | Vit china front urinal basin |
| 192 | PART -C : INTERIOR FURNISHING WORKS |
| 193 | Providing & fixing at all height FALSE CEILING including providing & fixing of frame work made of special sections power pressed from M.S. sheets and galvanised with zinc coating 120gsm/sqm as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts ,other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length, and with nut and bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x 0.9mm running at the spacing of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the perimeter channels 0.5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceiling fixed to wall partition with the help of rawl plugs at 450mm centre to centre with 25 mm long drive-all screws @ 230mm interval including jointing & fixing of gypsum board of ceiling section & perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm centre to centre including jointing and finishing to a flush finish of tapered & square edges of the board with recommended jointing compoud. Jointing tapes, finishing with jointing compoud in 3 layers covering upto 150 mm on both sides of joint & 2 coats of primer suitable for board, all as per manufacturer specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, complete as per drawing & specification and direction of the Engineer in Charge but excluding the cost of painting with: |
| 194 | ii) 12.5mm thick tapered edge moisture resistant GYPSUM BOARD CONFORMING TO IS: 2095- PART-I |
| 195 | Providing & Fixing 15mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/cosmos / Hexa or equivalent) of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38mm made from 0.33mm thick (minimum) sheet, spaced 1200mm centre to centre, and cross \\"T\\" of size 24x28mm made out of 0.33mm (Minimum) sheet, 1200mm long spaced between main'T' at 600mm centre to centre to form a grid of 1200x600mm and secondary cross 'T' of length 600mm and size 24 x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600mm panel to from grid of size 600x600mm resting on periphery walls / partitions on Perimeter wall angle pre- coated steel of size(24x24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edges calcium silicate ceiling tiles of approved texture (Spintone/Cosmos/hexa) in the grid including,cutting/ making opening for services like diffusers, grills,light fittings, fixtures, smoke detectors etc., wherever required, Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm ceiling with 12.5 mm dia and 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanised steel level clips of size 85x30x0.8 mm spaced at 1200mm centre to centre along main'T', bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked paint for all heights,as per specifications,drawings & as directed by engineer-in- charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames /opening (cut outs) having area less than 0.30 sqm.The calcium silicate tile shall have NRC value of 0.50(Minimum), light reflection > 85%, non - combustible as per B.S. 476 part IV, 100% humidity resistance & also having thermal conductivity<0.043 w/mK |
| 196 | Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS:8183 density 24kg/m3, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24g wire and mesh, for top most ceiling of building. |
| 197 | WALL PANELLING WITH LAMINATED FINISH : Providing PANELLING ON WALLS including corners of windows, columns, etc. consisting of frame work with 50 mm x 25 mm well seasoned hard wood @ 600 c/c (approx.) both ways jointed rigidly with nails, screws etc. fixed to walls, columns etc. with wooden plugs fixed with cement mortar (1:3) and providing & fixing 6 mm . thk BWP plywood, Century/Greenply or approved equivalent on top of frame work and finishing with best quality 1 mm thick Laminate ( Greenlam, Century Mica, Marine, Formica) of approved shade & finish to be pasted over ply without nailing. Finally the panelling will be finished with 60 x 35 mm thk Teak wood corner moulding at the junction of ceiling and wall (in case of full height panelling) and 35 x 12 mm teak wood boading on top ( in case of low height paneling) and fixing 100 mm x 12 mm thick Teak wood skirting . The rate to also include cost of applying preservative treatment of timber for rot & termite proffing, applying fire retardant paint and finishing the exposed surface of timber with stained spirit polish to the desired colour & melamine finish, provision of extra frame work as necessary for Teak wood skirting & making cut outs for electrical fittings all as per drawings, specifications & directions of the Engineer in charge. |
| 198 | Providing & fixing in position DOUBLE SKIN LOW HEIGHT PARTITIONS on floor consisting of 50 x50 mm well seasoned hard wood battons placed at 600 mm c/c bothways, jointed rigidly with nails, screws etc. & fixed to the floor with metal clamps grouted to floor and providing and fixing 6 mm thick BWR plywood as per IS 303 of \\" Green ply / Century or approved equvalent make on both sides of the frame work and best quality 1 mm thick laminated sheet of \\" \\"Greenlam\\", \\"Formica\\" \\"Century Mica\\" Marine make of approved shade, design, & texture to be pasted over the plywood with fevicol SH etc. without nailing in approved patterns.Finally the partition will be provided with 100 x 12 mm Teak wood skirting and 75 mm x 12 mm Teak wood moulding at the top complete with high gloss polishing with Melamine finish, grouting of frame work in walls, floors, etc. with all enabling works complete as per drawing and direction of Engineer in charge. The rate to also include cost of applying preservative treatment of timber for rot & termite proofing (ASCU), finishing the exposed surfaces of timber with stained spirit polish to desired colour & melamine finish. |
| 199 | WALL PANELLING WITH WOODEN VINEER: Providing & fixing panelling with one side Decorative plywood having natural veneer of select wood on walls including corners of windows columns , column cladding etc. consisting of frame work with 50 mm x 25 mm size seasoned Sal wood @ 600 mm c/c ( approximately) bothways ( i.e horizontally and vertically) jointed rigidly with nails, screws etc. with wooden plugs fixed with cement morter ( 1:3) and providing and fixing 6 mm thick BWR plywood (Greenply / Centuryply make) on top of the frame work and 4 mm thick one side decorative plywood vineers (Red oak/walnut/cherry/beech/white oak/white ash/swedish/cidar/maple or other approved shade and texture of Greenply/ Centuryply make) of approved shade & texture to be pasted over the plywood with adhesive (Fevicol) without nailing in approved pattern. Finally the paneling will be finished with 25 mm x 100 mm teakwood skirting .The rate to also include cost of applying preservation treatment of timber for rot & termite proofing with wood preservative oil of Berger make fire profing, finishing the exposed surface of timber with stained spirit polish to the desired colour and melamine finish of (Wood keeper of Berger make) melamine finish on decorative plywood, provision of extra frame work as necessary for skirting and making cutouts for electrical switch board, conuits etc. all as per drawing and direction of the Engineer in charge . |
| 200 | ACOUSTIC Wall Panelling with OPTRA or approved equivalent Acoustic Board. Providing and fixing in position Armstrong ' Optra Acoustical Wall Panelling' with square edges made of fibre glass substrate 25 mm thick and wrapped on the front side with an acoustically transparent and fire- resistant of approved shade of size 2100 x 600 x or 600 x 600 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using wall panel impalers of Armstrong make fixed to the wall surface wiring self tapping crews and construction adhesives as per the instructions laid down by the manufacturer . size of Metal Impaler is 77 x 102 mm. Armstrong Optra Wall panels shall be piercEd through the spikes of the impalers ensuring the line & level of the panels complete as per drawing & direction of the Engineer in charge. |
| 201 | FIXING 4 MM THICK DECORATIVE PLYWOOD VINEER : Providing and fixing 4 mm thick decorative plywood vineer of Century/Greenply make & shade on old and new surface including the cost of preparation of surface, applying adhesive.( Fevicol/vamicol) applying laquer on decorative plywood vineering etc. with all enabling works complete as per design and direction of Engineer in charge. |
| 202 | Providing and fixing 1.00 mm thick LAMINATE of approved shade finish and make ( GREENLAM / CenturyMica / Merino / Formica) on new/old surface, including the cost of preparation of surface, supplying and applying Fevicol or equivalent adhesive with all labour and material complete , as per specifications and directions of Engineer in charge. |
| 203 | Providing and fixing in position FRAMELESS glass partition with 12mm thk toughned glass of saint gobian/Pilinkton/Modiguard make fixed to floor and sofit of ceiling/false ceiling rigidly and at centres wherever required in line and level with SS patch fittings of DORMA/OZONE/HAFELLE make with all enabling works complete as per drawing and direction of EIC |
| 204 | Providing and fixing self adhesive type frosted glass film of 3M make or approved equivalent, in required pattern over glass etc. as per drawings, including cleaning the receiving surface of glass etc., all complete as per manufacturer's specification and direc tion of Engineer in charge: Plain frosted film |
| 205 | Providing and fixing self adhesive type frosted glass film of 3M make or approved equivalent, in required pattern over glass etc. as per drawings, including cleaning the receiving surface of glass etc., all complete as per manufacturer's specification and direc tion of Engineer in charge: Colored frosted film |
| 206 | Providing and fixing best quality 100mm size vertical venetian blinds of approved brand and make like \\"Vista Classic\\" of Vista Levelor or approved equivalent, design, colour(s) and quality as per specifications and directios of the Engineer-in-Charge with all labour, tools & tackles, hardwares and all other materials complete. |
| 207 | Spplying , fitting and fixing of roller blind similar to the Trippilite system of PACKMAN consist of 38mm OD extruded out of alluminium alloy 6063 T6 with silver anodized to provide an evarlasting finish and luster, the rotary unit shall be 36mm in OD incorporating a clutch mechanism composed of low -flexing braided polyster cord with nylon core, Control ball chain shall be composed of braided nylon cord (2mm dia) with high engineering grade plastic beads of 4.5mm diameter mounted co-axially on the cord with a pitch of of 6.2mm (C-T-C)Bottom rail should be powder coated steel with 12mm OD with 180gm to finish it from the ends and it should have rail end caps. There has to be proper hoodcover and the clutch will be at the tube. The return end cap bracket shall incorporate snap spring design to facilitate easy installation and removal for maintainance activites. The bracket shall be finished with a flush mounting cover on each side providing an aesthetic finish. It should handle up to 6Kg of material. The clutch should mount flush to the face of the bracket which minimize the light gap between the shade and the window frame. |
| 208 | Providing and doing Melamine polishing on wood work with applying filler coat followed by stainer coat then min. two coats of sealer followed by min. 2 top coats, sand papering and finally polishing with cream including putting Matt spray coat all complete as per direction of engineer |
| 209 | CARPET TILES: Providing & fixing in position of Carpet Tiles approved makes of Mohak/Shaw/Interface/Unifloor or as equivalent as per approved make & shade at existing Floor & Riser: Product type - Tufted Textured Loop, Face Fiber - 100% PP, Pile Height - 3.5 MM, Pile Weight : 550g / m2, Total Weight - 3120 g/m2, Gauge - 1/10, Primary Backing - Non Woven Polyster Spunbounded , Secondary Backing - PVC with Glass Fiber, Size 50 x 50 cm.\\" |
| 210 | Providing, fitting and fixing in position 6 mm thick coloured lacquered glass of any approved shade and design fixed over Ply / MDF board panel, fitted with necessary Adhesive , clips, fasteners as required and as per Manufacturer' Specification. Toughened float glass of special selected quality free from bubbles, holes or any surface deformation. Allow for cutting, chase to walls, lintel and floor and mending good damages. The rate should include for providing necessaryHoles in glass, approved quality adhesive, etc,as per approved shade and design, etc complete in all respects with necessary support as per drawing and direction,with all labour and materials. |
| 211 | Providing and supplying italian marble / onyx marble stone of specified type , quality and texture |
| 212 | 18 mm thick Honey Onyx marble |
| 213 | 18 mm thick Mango Onyx marble |
| 214 | 18 mm thick Agate Onyx marble |
| 215 | Supplying, fitting and fixing MAC blinds horizontal and verticalcomplete as specifiedand directed by the department at all levels. Blackout or equivalent:100 mm |
| 216 | Provision of drip irrigation system for all plants in the green wall, with prior approval from IOCL and as per the directions of Engineer-in-Charge |
| 217 | 12mm dripping pipe supply & laying for drip irrigation system |
| 218 | Supply of sign boards made of ACP sheet with reflective Vinyl Letter cutting and pasting. ACP sheet thickness shall be between 3mm to 4mm. Unit of Measurement (\\"2) stands for size of ACP sheet in Square Inch. |
| 219 | supply of Raised Stainless steel letters along with hanging arrangement. The stainless steel sheet shall be of 20-22 gauge. The unit of measurement () stands for per Inch width of the letter. The width to height ratio of the letters shall be as per standard proportion. |
| 220 | SCULPTURE OF ENTRANCE: Supplying and fixing in position Fibre Glass Scupler of height 4'-0''- 4'-6 with a frame of 1' including with all necessary fittings & fixtures . |
| 221 | Internel signages |
| 222 | Cabin Signage: size 62mm x 300mm flat shaped alumninium extruded sliding changeable signage complete with black coloured plastic & caps on both sides. sides and caps. Polycarbonate sheet of required thickness with the name printed on computerised cut vinyl. All in the required shade and instruction of the architect / engineer-in-charge. |
| 223 | Stainless steel brush finish signage complete with message in etching process. The thickness of the signage would be 20 gauge. Stainless steel would be of 304 grade. The signage would be without paint filling. The signage would be attached with the glass surface. |
| 224 | signage of 8in x 6in |
| 225 | signage of 12in x 8in |
| 226 | signage of 24in x 12in |
| 227 | Stainless steel raised 3 dimensional alphabet with proportionate width. The letter would be raised by approximately 1 inch. |
| 228 | height of 8in to 12in |
| 229 | height of 6in to 8in |
| 230 | Fire Exit Signage : P/I \\"Fire Exit\\" signage on 4\\"x8\\" acrylic panels in glo-sign & green film with directional indications as directed. |
| 231 | Providing and fixing |
| 232 | Providing and fixing |
| 233 | Providing & fixing Livin wall paper gravure printed-pre-trimmed-washable -strippable of approved shade and design including preparation of wall surface, fixing with sutibale glue as per the manufacturer specification and as per direction of EIC |
| 234 | Supply & Installtion of Pull - Push Signages : Brush finish stainless steel etched signs Size : 2.5\\"\\"(H) x 2.5\\"\\"(W) set includes 1 pull & 1 push.\\" |
| 235 | Providing and fixing White mark make of white boards of the all sizes. Rates of the white board to be inclusive of accessory kit like pen stand, duster, magnets etc. |
| 236 | Providing and arranging artificial plants like creepers, leaves etc or flower arrangments. Including the pots with marble / stone pebbles, moss etc. as per approval and selection by architect. |
| 237 | Meadium bushes & creapers upto 300 mm ht. with basic rate Rs 1500 (basic rate excluding taxes & freight/transportation) |
| 238 | Artificial small plants arrangement upto 1200 mm ht. with basic rate Rs 3500 (basic rate excluding taxes & freight/transportation) |
| 239 | Artificial big plants arrangement upto 2100 mm ht. with basic rate Rs 6000 (basic rate excluding taxes & freight/transportation) |
| 240 | Providing & fixing of artificial grass with following specifications: 1. Pile height : 35mm 2. Gauge : 3/8\\" 3. Stitches : 14/10cm 4. Density : 14700/m2 +/- 3% 5. Yarn Type : PE (C-shage) + PP 6. DTEX : 9200 7. Total w.gr/m2 : 2241 g/sqm 8. Yarn W.gr/m2 : 991 g/m2 9. Backing : PP Cloth, Net SBR Glue. Grass should have warranty for color fading and bald patches. The rates are inclusive of all materials, tools & tackles and installation complete. |
| 241 | Providing, fitting and fixing coloured anodised aluminium hollow (Indal section 9210) of size 63.50 x 38.10 mm x 2.5 mm thick for aluminium frame partition wall, with a maximum spacing of frame 1.20 for horizontal/vertical member including aluminium cleat 32 mm x 50 mm x 4mm thick and fixing of pre-laminated board /Nepal board/ Bhutan board / 5 mm frosted glass with tapper cleat 20mm x 15mm x 1.2mm thick as directed by department at all levels. |
| 242 | 5 mm frosted glass |
| 243 | Providing, fitting and fixing coloured anodised aluminium framed sliding glazed doors with partition walls with anodised aluminium frames made of 100mm x 43 mm x 2 mm section with door style of size 81mm x 43mm x 2mm, top rails 46 mm x 43 mm x 2mm, lock rails 81 mm x 43 mm x 2 mm,paints and 12 mm prelaminated board fitting with glazing clip,special type rubber gasket cmplete including roller, door handle, lock angles, cleat etc.complete as directed by the department at all levels. |
| 244 | 5 mm frosted glass |
| 245 | VERTICAL WALL GREENERY: Providing and developing Vertical wall greenery Supplying and Fixing flower panel drip deeper flower chain pipe to create green wall. Green wall shall be completely covered with greenery that includes a growing medium, such as soil and an integrated water delivery system. Green walls to have growing media supported on the face of the wall. Job includes maintenance of green wall for three months. Green walls shall be fixed indoors or outside, freestanding or attached to an existing wall, All complete as per the direction of Engineer - in - charge / site engineer |
| 246 | Specially designed 3D mural work with Handmade Ceramic Mural Art Tiles/fibre in various sizes and colours cut to shape at site with three-dimensional effect, may be 1 to 6\\" -8\\" approx. embossed as per requirement of the design from finishing with Tiles/fibre on sides also, if required. |
| 247 | Providing and fixing photo mural of approved design and shape with UV curved inks fixed on board with S.R. adhesive complete in all respect. The job includes all materials and consumable including repairing the surface wherever required and providing scaffolding if any, all complete to the satisfaction of Engineer-in-charge. |
| 248 | PART -D : ELECTRICAL WORKS |
| 249 | Supply & Installation of 20 KVA UPS with 100Ahx 24 no's SMF Batteries and MS Rack. 24 months warranty. |
| 250 | Supply, Installation, Testing and Commisioning of Indoor type LT Switchboards, Floor mounting type, Bottom/Top entry.Ref enclosed SLD Enclosure: Compartmentalised Single front CRGO(Cold rolled grain oriented sheet steel) Doors:2mm/Body:2mm/Gland:3mm/covers,partitions:1.6mm IP class:IP52 for Indoor/IP65 with wheather proof enclosure for outdoor Busbars: Electrolytic grade conductivity Busbar suppotrs:DMC/FRP/SMC Loovers:Busbar chamber shall have louvers with fine mesh inside Shade:Epoxy powder coated RAL 7032 Design:Modular type Cable entry:As per site condition All panels shall have space heaters Note:1) All the breakers shall have potential free aux NO/NC conatcs for ON,OFF,TRIP 2) All the breakers shall have spreaders/phase separators/RHOM/Pad lock/Door lock/trip free 3)Breakers shall have provision to add shunt trip 4)All the AHU feedres shal be provided with shunt trip 5) Insulated shrouding shall be provided for live parts 6) FRLS PVC copper wires shall be used for control wiring 7) CT's shall be provided with shorting terminals 8) The dual source PDU's for Server/Hubroom shall be of different colour |
| 251 | MAIN LT PANEL Incoming 1 No. - 200A, 4P MCCB (Icu = 36 KA, Ics = 100% Icu) with extended rotary operated mechanism and O\C, S\C, S\T Releases with aux & trip contact. Led type on, off & Trip indicating lamp. RYB Indicating Lamps of LED clustered type and Control MCBs shall be provided with ELR, Shunt trip, NO/NC contacts Type1+2, 50KA SPD with Isolator 1 Set - 3Nos. Dual Core tape wound CTs of Class1.0 for measurement and class 5P10 for Protection. The CT burdens hall be 15VA. 1Nos. 200A, 4P, ATS 1 Set - Load Manager with RS 485 Interface and BMS compatible. panelvendor to provide Serial data of load manager/Main parameters onModbus/Bacnet including Modbus/Bacnet port , provision for BMS cableentry & Protocol Integration details. Potential Free Contact and therequisite internal cabling upto RS 485/ BACNET port shall be provided byElectrical vendor Bus Bar 1 Set - 3 Nos 50 mm x 5 mm and 1 No. 40 x 5 mm for neutral, tinned Cu busbars covered with colour coded MKV graded PVC sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing 3 No. - 32A, 4P MCCB, Icu = 36 KA, 6 No. - 40A, 4P MCCB, Icu = 36 KA 8 No. - 63A, 4P MCCB, Icu = 36 KA 2 No. - 100A, 4P MCCB, Icu = 36 KA Earth Bus Bar 25 mm x 6 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. 1 - Danger Board. Complete Board as stated above. . |
| 252 | UPS O/P PANEL Incoming 1 No. - 63A, 4P MCB (Icu = 10 KA) Led type on, off & Trip indicating lamp. RYB Indicating Lamps of LED clustered type and Control MCBs shall be provided with ELR, Shunt trip, NO/NC contacts SPD with Isolator 1 Set - 3Nos. Dual Core tape wound CTs of Class1.0 for measurement and class 5P10 for Protection. The CT burdens hall be 15VA. 1 Set - Isolation Transformer 1 Set - 1 No. Load Manager with RS 485 Interface and BMS compatible. panelvendor to provide Serial data of load manager/Main parameters onModbus/Bacnet including Modbus/Bacnet port , provision for BMS cableentry & Protocol Integration details. Potential Free Contact and therequisite internal cabling upto RS 485/ BACNET port shall be provided byElectrical vendor Bus Bar 1 Set - 3 Nos 25 mm x 5 mm and 1 No. 30 x 5 mm for neutral, tinned Cu busbars covered with colour coded MKV graded PVC sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing 12 No. - 32A, DP MCB, Icu = 10 KA, (D-curve) Earth Bus Bar 25 mm x 3 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. 1 - Danger Board. Complete Board as stated above. [Non Schedule Item]. |
| 253 | Distribution Boards- 4Way TPN Horizontal PPI DB (Metal door, IP-43) Incomer : 63A 4P MCB -1 No Sub-Incomer : 40A DP RCCB of 30 mA -3 Nos Outgoings : 10/16A SP MCB - 12Nos |
| 254 | Distribution Boards- 8Way TPN Horizontal PPI DB (Metal door, IP-43) Incomer : 63A 4P MCB -1 No Sub-Incomer : 40A DP RCCB of 30 mA -3 Nos Outgoings : 10/16A SP MCB - 24Nos |
| 255 | UPS/ Emergency Distribution Boards- 12Way SPN DB Incomer : 32A 100mA DP RCBO-1 No Outgoings : 6A SP MCB - 2Nos |
| 256 | 63A MCB WITH ENCLOSURE Supply, installation, testing and commissioning of 63A TPN MCB (Ics = Icu = 10 KA) with enclosure box with all accessories as per specification attached complete in all respects as required at site. |
| 257 | 40/32A 3P+N+E Surface mounting industrial Socker & Plug with interlocking arrangement, weather proof (IP 67) for AC ODUs |
| 258 | LT CABLES \\"Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/existing trench/surface/pipe/structure, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays,pipes, trenches, abricated tray supports etc will be covered & paid in Separate Items.\\" |
| 259 | 3.5 Core x 185 sq. mm Aluminium Cable |
| 260 | 4 Core x 16 sq. mm Aluminium Cable |
| 261 | 3 Core x 4 sq. mm Copper Cable |
| 262 | 1CX25 SQMM.PVC CU FLEXIBLE CABLE. |
| 263 | 1CX25 SQMM. CU Flexible cable |
| 264 | Supply , wiring and fixing of 3No 6A Socket controlled by 1no 16A Switch with indicator including suitable size GI box with modular plate and cover in front on surface or in recess, including providing connections with 3x1.5 sq.mm. FRLS PVC insulated copper wire,conduit, flexible etc. as required (for computer). |
| 265 | Supply & Fixing 240 V, 16 A, 3 pin Modul |
| 266 | SUPPLY AND FIXING OF LIGHT AND FAN FIXTURES : |
| 267 | 20W Extruded Aluminium housing LED batten 1200mm Long (Philips Model No: BN 021 LED40S- 6500 PSU GR (4 ft) or Eqv.) |
| 268 | 30W 600x600mm LED Panel Light (Philips Model No: RC380B LED30S -6500 G4 L60 W60 PSU OD or Eqv.) |
| 269 | 10W LED Recessed Mounted Downlight (Philips Model No: Aura StylEdge or Eqv.) |
| 270 | 10W Linear Light with 5700K of CCT (Philips Model No: SP095V LED40S 865 W7L120 PSU WH or Eqv.) |
| 271 | 300mm sweep exhaust fan (Ventil Air - DS |
| 272 | LT Cable Heat Shrinkable Indoor/ Outdoor cable end termination Providing end termination of power cable including cutting, stripping, providing lugs, cable insulation, providing and glanding with single/double compression heavy duty brass cable gland conforming to IS-12943 , wherever specified, providing aluminium lugs, crimping/soldering, as necessary, restoration of insulation/ clamping of cable, tagging with aluminium tag,earthing of armour, connection to the equipment terminals etc. all complete with labour and materials as per standard and direction of the Engineer-in-Charge. Make of kits shall be of Raychem/ CCI/ approved equivalent make. |
| 273 | 3 / 3.5 / 4 X 185 SQMM |
| 274 | 3 / 3.5 / 4 X 16 SQMM |
| 275 | SUPPLY & FIXING OF RECESSED PVC CONDUIT |
| 276 | 20 MM |
| 277 | 25 MM |
| 278 | 32 MM |
| 279 | 40 MM |
| 280 | 20 A SPN. MCB INDUSTRIAL SOCKET OUTLET |
| 281 | PROVIDING EARTHING ELECTRODE |
| 282 | 65 MM DIA 3 METRE LONG |
| 283 | SALT AND CHARCOAL FOR PIPE EARTHING |
| 284 | 64 KG CHARCOAL AND 5 KG SALT |
| 285 | EARTHING WITH GI STRIP |
| 286 | 25 X 5 MM GI STRIP |
| 287 | EXCAVATION OF EARTH FOR ELECTRICAL WORK |
| 288 | SFI OF GI CABLE TRAY |
| 289 | 150 MM X 25 MM X 2 MM |
| 290 | 300 MM X 25 MM X 2 MM |
| 291 | COPPER POINT RECESSED MODULAR SWITCH |
| 292 | Conduit length upto 2.5m - Group A |
| 293 | Conduit length above 2.5m and upto 3.5m |
| 294 | Conduit length above 3.5m and upto 4.5m |
| 295 | LT PLUG POINT-COPPER WIRING IN PVC-R |
| 296 | CU CIRCUIT WIRING PVC CONDUIT(2X1.5)-R |
| 297 | CU SUBMAIN WIRING IN PVC CONDUIT-R |
| 298 | 2 x 2.5 sqmm + 1x2.5 sqmm earth |
| 299 | 2 x 4 sqmm + 1x4 sqmm earth |
| 300 | PART -E : FIRE FIGHTING WORKS |
| 301 | LAYING & WELDING OF FIRE HYDRANT PIPELINES (ABOVE GROUND) IN ZONE-B Laying and welding(3 runs minm.) Above Ground Pipelines from supplied MS pipes(pipes to be supplied any where within the depot and the contractor shall shift the same to the site of work at no extra cost with all lead sand lifts) of the following sizes as described below, including cutting, bevelling and fixing the supplied specials such as elbows, bends, tees, reducers, etc. complete and successful hydrotesting the pipeline at a pressure of 10.5 kg/cm2 for a minimum period of 4 Hrs. The job includes Dye Penetration (DP) testing of pipeline joints as per approved QAP. Above ground pipeline to be laid on concrete pedestals(which is to be constructed as per the respective item of this schedule) / piperacks / Fire Hydrant pumphouse & manifolds and Painting the pipeline as per the specifications enclosed including the colour coding as per IOC specifications.(radiography shall not be done for fire hydrant lines & for lines to be used for water services).Note: a.AnyrepairstothedefectiveweldingshallbemadegoodatnoextracosttoI OCL.Re-radiographyof repaired joint shall also be at contractor's cost.b. The rates quoted also to include Painting and colour coding of pipelines as per the standards. c. For the sizes of piping below 150mm, direct stub connection shall be made on the headers with suitable pad plates and the rate quoted should include the same. Painting Scheme: Application for External painting shall be carried out by means of AIRLESS SPRAY PAINTING SYSTEM only. 1. Surface Preparation as per SA 2½2. Primer : P3- Red Oxide Zinc Phosphate Primer - 2 Coats (30-35? each), DFT 60-70? 3. Finish Coat : F2- Aluminium Finish Paint - 2 Coats (15-20? each), DFT 30-40? Total Min DFT 90? |
| 302 | 100 mm dia |
| 303 | 80 mm dia |
| 304 | LAYING & WELDING OF UNDER GROUND PIPELINES (PRODUCT/FIREHYDRANT) IN ZONE A & ZONE B - with EPOXY COATING PAINTING: Laying and welding (3runs min.) underground/below ground pipelines from supplied MS pipes (pipes to be supplied any where within the depot and the contractor shall shift the same to the site of work at no extra cost with all leads and lifts) of the following sizes as described below, including cutting, bevelling and fixing the supplied specials such as elbows, bends, tees, reducers, etc. complete and successful hydrotesting the pipeline at a pressure of 10.5 kg/cm2 for a minimum period of 4 Hrs. The job includes Dye Penetration (DP) testing of pipeline joints as per approved QAP. Under ground pipelines to be laid at a depth as per site condition/laying through hume pipes/culverts & Painting/Coating the same as detailed in the enclosed specifications. (i)Welding of Product Pipeline should conform to Radiography quality. 10% of the joints shall be radiographed and the cost of the same will be paid separately as per respective item, etc. and as directed at site. Re-radiography of repaired joint shall also be at contractor's cost. (ii) for Welding of Fire Hydrant Pipeline-radiography shall not be done for fire hydrant pipelines & for pipelines to be used for water services. Note: a. Any repairs to the defective welding shall be made good at no extra cost to IOCL. b. Civil works for laying of UG pipeline laying will be paid separately. c. Coating Painting to be done as perspecification given below & detailed specification given in tender document.d. The rates quoted also to include Painting and colour coding of pipelines as per the standards. e. Painting Scheme: Application for External painting shall be carried out by means of AIRLESS SPRAYPAINTING SYSTEM only.1. Surface Preparation : as per Sa 2½2. Coating:(i)1coat PolyUrethane coating (100% Solvent free) system-DFT1000 Micron minm.OR (ii) 1coat High Build Solvent free Liquid Epoxy Coating - DFT800 Micron minm.- for the following Pipe sizes : |
| 305 | 100 mm dia |
| 306 | SUPPLY OF MS PIPE: IS-1239 Gr. C Heavy Duty |
| 307 | 80 mm dia |
| 308 | 100 mm dia |
| 309 | Providing and fixing forged brass ball valve with forged brass ball (suitable for test pressure of not less than 10 kg / sq.cm of the following size : (Make- LP/Kartar) or approved equivalent - 25 mm dia |
| 310 | Providing & fixing of butterfly valve (PN 16) with flanges, nut bolts, gaskets and necessary pad locking arrangement complete required. (Make- LP/Kartar) or approved equivalent - 100mm Dia |
| 311 | Providing & fixing C.I. wafer type check valve of rating PN 16 rating including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required. (Make- LP/Kartar) or approved equivalent - 100 mm dia |
| 312 | Providing, fixing and commissioning of spring loaded relief valve with drain arrangement suitable for pressure of 15 Kg / sq.cm including flanges, nuts, bolts, washers etc. complete as required. - 25mm dia |
| 313 | Providing & fixing SS 304 fire hydrant single landing valve with 80 N.B. flanged inlet, brass spindle controlled 63 mm dia female instantaneous outlet type SS 304 coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS:5290. Including fixing with anchor fastner and flanged tapping from wet riser and providing pressure gauge with gun metal ball valve complete as required. (Make- Kartar/Safepro Fire/Safe Guard) or approved equivalent |
| 314 | Providing & fixing swinging type First Aid hose reel in red colour drum with 36 mts long and 20 mm dia heavy duty rubber water hose, 20 mm dia gate valve stop cock, (IS:778, class - II) terminating with S.S. coupling & nozzle of 6mm outlet with shut off valve confirming to IS 8090 - 1976 complete with MS socket for tap-off, drum and brackets (including painting) for fixing on wall with anchor fastner, bolts & nuts conforming to IS:884-1985 (Reaffirmed 2000) complete as required. (Make- ZENITH or approved equivalent) |
| 315 | Providing & fixing non-percolating rubber reinforced lined fire hose pipe (as per IS : 636) type-B of 63 mm dia and length as described below. The hose shall be rated for brust pressure of 35.7 Kg/sqcm. Hose shall be complete with ISI marked brass male & female coupling (IS:903) bound & rivetted to hose pipe with copper rivets & 1.5 mm copper wire (Location : Internal/External fire hydrant) (Make- Kartar/Safepro Fire/Safe Guard or approved equivalent) - 15 metre length |
| 316 | Providing and Fixing 63 mm dia instantaneous pattern branch short SS-304 pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling complete as required. (Make- Kartar/Safepro Fire/Safe Guard or approved equivalent) |
| 317 | Providing and fixing weather proof lockable cabinet of size not less than 0.75 x 0.60 x 0.25 mtr made out of SS 304 sheet of 16 gauge thickness having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside with the letters \\"FIRE HOSE\\" including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint of approved shade. The cabinet shall be suitable to accommodate 2 nos. 15 mtr long Hose pipe & 1 Nos branch pipe nozzle. It shall be mounted on raised Brick platform complete as required.(Cost shall be inclusive of providing break glass box containing key for the cabinet along with hammer). (Make- ZENITH or approved equivalent) |
| 318 | Providing & fixing gun-metal Fire Service Inlet connection to directly pressurise the system consisting of 2Nos. 63 mm dia instantaneous type male couplings with built-in check valves. (Make- Kartar/Safepro Fire/Safe Guard or approved equivalent) |
| 319 | Portable Chemical Fire Extinguishers: |
| 320 | 6 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked/ TAC approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:1349-1993. (Make - Safe Pro Fire/safe Guard or approved equivalent) |
| 321 | 4.5 Kg ISI marked (IS:2878) portable CO2 type fire extinguisher type. Including valve, discharge hose of not less than 10 mm dia & 1 M long complete in all respects including initial filled with CO2 gas confirming to IS:307-1966 & filled to a filling rate of not more than 0.667 and wall suspension bracket. (Make - Safe Pro Fire/safe Guard or approved equivalent) |
| 322 | 9.0 Litres Mechanical foam type fire extinguisher. In HP mild steel cylinders ISI marked TAC approved fitted with pressure indicating gauge, internal tube, squeeze level type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and conforming to IS: 910. (Make - Safe Pro Fire/safe Guard or approved equivalent) |
| 323 | Fire buckets (FILLED WITH SAND) round bottom type enamel painted, white inside & Red out side and Letter \\"FIRE\\" in black out side and handle with mounting bracket. |
| 324 | FIRE ALARM SYSTEM |
| 325 | Supply, Installation, Testing And Commissioning of complete intelligent, addressable, analogue, zoned, non-coded and electrically supervised , multiple loop fire alarm and detection system, including initiating devices and notification appliances. The system shall interface with 3rd party systems and perform monitoring, controlling, annunciating functions. All equipment furnished and mentioned shall be new and latest and products of single manufacturer as listed in technical spe cifications, all requirements of contract works. The system shall be modular and expandable and shall include following but not limited to: |
| 326 | UL Listed Microprocessor based analogue addressable 1 Loops fire alarm control panel with minimum 80 characters LCD display. Each loop of panel shall have minimum capacity of 250 (125 Detectors + 125 Devices) analogue addressable devices, The panel shall be UL 9th Edition listed and shall be in compliance with technical specifications. (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 327 | UL listed Repeater panel for accessing the information from alternate locations. The Repeater Panel shall include a minimum of 80 characters, backlit by a long life, solid state LCD. It shall be equipped with rubberized key pad. The keypad is functional only when an entry is requested by the system. There shall be fixed and soft keys for functional requirements as per technical specifications. (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 328 | UL listed analogue addressable smoke/Heat detector with mounting based LED, Address Switch / electronic way of addressing, complete as per all requirements of technical specifications & contracts works. (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 329 | UL Listed Fixed temperature cum rate of rate of rise heat detector with mounting based LED, Address Switch / electronic way of addressing, as per technical specifications and all requirements of contract works. (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 330 | UL listed, dual action (push IN-pull DOWN) Flush or surface mounted Manual Call Point in manufacturers prescribed matching red enamel outlet box complete with key operated test-reset lock. The word FIRE shall appear in front of station as per technical specifications and all requirements of contract works. (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 331 | UL listed, Strobe cum Hooter, wall mounted as per technical specifications and all requirements of contract works. (Make- Honeywell Syatem Sensor, UL Listed or approved equivalent) |
| 332 | Addressable Interface Devices: Providing, fixing, testing and commissioning UL listed modules complete with mounting arrangement on north American junction box as per technical specifications and all requirements of subcontract works. Following devices shall be used but not limited to: (Make- Honeywell Morley IAS ,UL Listed or approved equivalent) |
| 333 | Monitor Module |
| 334 | Control Module |
| 335 | Isolator Module |
| 336 | Fire Survival unarmoured cables with annealed copper conductor having Cross linkable Low smoke zero halogen insulation and LSZH inner and outer sheath. Cable should comply to BS-7629 Part -1 (latest edition). The cable should meet fire performance circuit integrity test as per clause 26.2e of BS 5839-1 for Enhanced Fire Resisting cables when tested in accordance to BS 8434-2 (CWZ test on one sample @ 9300C & not on separate sample). (Make- Polycab/Mescab/Havels or approved equivalent) |
| 337 | 2c x 1.5 m² wire |
| 338 | 2c x 2.5 m² wire |
| 339 | PART -F : HVAC WORKS |
| 340 | Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units , having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .The compressor and VRV/VRF Outdoor make should be same. The unit shall also have feature to automatically modulate the evaporative temperature between 6 deg C to 11 deg C with respect to load for better comfort and energy efficiency. The Unit should have free phase technology so that unit can work in case of phase reversal also without tripping of units. - Outdoor unit (54 HP) |
| 341 | Supply Installation, Testing & Commissioning of following minimum capacity of 4-way/ round flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with cordless / corded remote ,synthetic washable media pre-filter, low noise fan/dynamically balanced blower,multispeed Brassless DC ( BLDC ) motor, DX copper coil, electronic expansion valve, outer cabinet, drain pan, drain pump, cassette grill, insulation, necessary supports,vibration isolation etc, suitable for operation on 230 V ± 10%, 50 Hz single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire.All indoor Units should have force shut option to connect with fire alarm adaptor, so that the unit automatically stops in case or fire.The cassettes units shall have dual sensor which detect the presence of people and floor temperature to provide comfortable air conditioning as well as energy saving. |
| 342 | 1.06 TR cooling capacity SPLIT Type in |
| 343 | 1.32 TR cooling capacity CASSETTE Type |
| 344 | 1.65 TR cooling capacity CASSETTE Type |
| 345 | 2.08 TR cooling capacity CASSETTE Type |
| 346 | 2.65 TR cooling capacity CASSETTE Type |
| 347 | Supply of factory supplied refnet piping joints with insulation |
| 348 | Installation of factory supplied refnet piping joints with insulation . |
| 349 | Refrigerant Piping: Supply & Installation of interconnecting refrigerant copper pipe of following minimum sizes & outer diameter,insulated with 19/13 mm thick closed cell electrometric Nitrile rubber tubular insulation between each set of indoor & outdoor units. The pipe dia upto 19mm shall be soft seamless & above 19mm dia shall be hard seamless. All piping inside the room shall be properly fixed/supported with suitable size of clamp/ M.S. hanger . |
| 350 | 41.3MM (19 MM THCIK INSULATION) |
| 351 | 34.9MM (19 MM THCIK INSULATION) |
| 352 | 28.6MM (19 MM HCIK INSULATION) |
| 353 | 22.2MM (19 MM THCIK INSULATION) |
| 354 | 19.1MM (19 MM /13 MM THCIK INSULATION) |
| 355 | 15.9MM(19 MM /13 MM THCIK INSULATION) |
| 356 | 12.7MM (13 MM THCIK INSULATION) |
| 357 | 9.5MM (13 MM THCIK INSULATION) |
| 358 | 6.4MM (13 MM THCIK INSULATION) |
| 359 | Providing and fixing UPVC heavy duty pipes with fittings with solvent cement joints including cuttings the pipes to correct length with nitrile rubber tubular insulation. ( 9 mm thick ) |
| 360 | 20 mm dia |
| 361 | 25 mm dia |
| 362 | 32 mm dia |
| 363 | 40 mm dia |
| 364 | Supply & fixing of MS stand for VRV outdoor unit as per adequate weight with necessary anticorrosive paints with double rubber pad in every mounting . |
| 365 | Supply and fixing of control cum transmission wiring of 2 C X 1.0 sq mm copper conductor along with suitable conduit for looping between indoor & outdoor VRF system/ ductable unit & to main central remote controller system. |
| 366 | SITC of Refrigerant Gas Charging R410A as per site requirements. |
| 367 | Lifting & Shifting of outdoor & indoor units |
| 368 | Scaffolding for ducting & piping work |
| 369 | PART-G :LAN & DATA |
| 370 | ETERNITY PENX6SAC # IP-PBX with Universal Connectivity and Mobile Extensions : • Universal Slots: 6 • Max. IP Users: 100 • Max. TDM Ports: • Built-in Ports: 5 IP Users*, 4 VoIP & 4 VMS , 2 Trunk Line 2 Digital Extention 12 Analog Extention [ Matrix Make OR APPROVED EQUIVALENT] |
| 371 | EON510, Digital Key Phone : • Programmable Keys: 20 (4 Context Sensitive Keys, 16 DSS Keys) • Display: 240x64 Pixels Graphical LCD with Backlit • Color: Black • Compatible P • Polyphonic Ringtone, Full Duplex Speaker Phone, Hold, Conference, Redial, Transfer, Message Wait Lamp, Ringer Lamp [ Matrix Make OR Approved equivalent] |
| 372 | CLI Telephone set [Beetel Make or Approved Equivalent] |
| 373 | 20 Pair MDF with Kron Modul [ ADC Make or Approved equivalent] |
| 374 | I/O with Face Plate [ Molex Make or approved equivalent] |
| 375 | Supply & Laying of Telephone (0.5 MM ) cable with PVC Conduit [ Finolex Make or approved equivalent] |
| 376 | Supply, Installation,testing & Commissioning of Data - Voice system as per below mentioned specification & BOQ: |
| 377 | Supply Installation and laying of 2mm thick PVC conduit with all necessary accessories like bends, collars, junction boxes,pull boxes ,fish wire concealed /Surface mounting complete as required. - 25 MM PVC Conduit Make: AKG/Finolex/BEC or Approved equivalent |
| 378 | Supply Installation, Laying and testing, of the network cable confirming to TIA/EIA standards, in the exsiting conduit, rate shall include all the required items complete as required. - CAT 6 cable Make: Molex/Polycab/Bonton/ Beldon/Dlink or approved equivalent |
| 379 | Supply and installation of data socket (RJ 45) outlet points with MS box, plate concealed etc., all complete as required.Make: D link/Legrand/Molex or approved equivalent |
| 380 | Supply and installation of Cable Manager Make: Molex/Polycab/Bonton/Dlink or approved equivalent |
| 381 | Supply and installation of 24 Port PoE Switch Gigabyte Make: Dlink/TP link/ Airpro/Cisco/ or approved equivalent |
| 382 | Supply and installation of 08 Port PoE Switch Gigabyte Make: Dlink/TP link/ Airpro/Cisco/or approved equivalent |
| 383 | Supply and installation of 16 Port Gigabyte Managed Switch Make: Dlink/TP link/ Airpro/Cisco/ or approved equivalent |
| 384 | Supply and installation of 6U Network Rack with accessories Make: VAL Rack/Netrack/or approved equivalent |
| 385 | Supply and installation of 24 Patch panel Make: Dlink/Molex/Commscope or approved equivalent |
| 386 | Supply and installation of Patch Code up to 2 Mtrs Make: Dlink/Molex/Beldon/Commscope or approved equivalent |
| 387 | Supply and installation of Connector RJ-45 Make: MX/Dlink/Molex or approved equivalent |
| 388 | Supply and installation of Dual Band access point at ceiling Make: Tplink/Dlink/Airpro/ or approved equivalent |
| 389 | Supply and installation of Controller for accesspoint Make: Tplink/Dlink/Airpro/ or approved equivalent |
| 390 | Supply Installation and laying of indoors multiplier 0.5mm dia annealed copper conductor of unarmoured PVC insulated telephone wires (copper) in pipe/conduits etc., all complete as required. Supply Installation and laying of 2 Pair Telephone UnArmoured Cable Make: Polycab/RR Kabel/Anchor/Bonton or approved equivalent |
| 391 | Supply, Installation and laying of indoors multiplier 0.5mm dia annealed copper conductor unarmoured PVC insulated telephone wires (copper) in pipe/conduits etc., all complete as required. Supply Installation and laying of 20 Pair Telephone unarmoured Cable Make: Polycab/RR Kabel/Anchor/Bonton or approved equivalent |
| 392 | Supply and installation of Telephone tag block (TJB) with KRONE terminal connectors,G.I.J.B as specified and complete with all interconnections and jumper connections between the two Tag blocks on all floors complete as required. Supply and Installation of telephone socket outlet points (RJ11 jack) with MS box, plate concealed etc., all complete as required. |
| 393 | Supply and laying of 2mm thick PVC conduit with all necessary accessories like bends, collars, junction boxes,pull boxes,fish wire concealed /Surface mounting complete as required. Supply & Installation of 25 MM PVC Conduit |
| 394 | PART-H SOUND SYSSTEM & VIDEO CONFERENCE |
| 395 | (A). Main Conference Room Audio & Video Solution |
| 396 | Supply, Installation, Testing and Comissioning of Boundary Microphones |
| 397 | Supply Installation and Commissioning of Digital Podium: Material: Mild Steel; Should have Tray for Keyboard. ( Keyboard Dimension Standard Lenovo Keyboard) Built-in Document Camera and 19” Interactive Panel .It should also have the flexible options in sizes for the 19” or 22” Interactive Panel to fit in. Interactive Panel positioning motorized up and down as per the user convenience . The top should be of wood. Should have a space for the Desktop in the 19” rack for the equipments to fit in as per the International standards. Sliding Shelf/Tray with Locks - For placement of extra lap top or Document to show through Inbuilt Documenment Camera and for Presenter with Internal Lock. It should have 3 options in lock- Manual key, RFID and Biometric (finger) for better security ands ease of use. The single slidling wooden shelf should cover all 3 equipments - Interactive Monitor, Document amera and multimedia controller. They should be hidden and should not be visible. It should have door locks. Visual Presenter or Document Camera should be installed and placed next to the interactive monitor for ease of use of both the items.Programmable Central Control System : Should be able to control from the Controller with easy identified keys - Projector On Off, Switching between PC, Visual Presenter and laptop, Volume Control. Ports and connectivity : - Front Panel should have touch sensing keys for Control, The controller should get on with a touch of smart key so onluy authorisew person can operate it. Power Plug 0f 220 Volt Power out for Laptop etc., HDMI Input x 1, VGA Input Port X 01, Audio port x 2, Network Port wired Internet x 01, USB X 01 Ports to facilitate inputs directly from Pen Drives / USB based hard disk Drive. Back Panel of the Controller should have, 1 x RS 232 Projector Control, 2 x 2 VGA matrix, 2 HDMI Input and 2 HDMI Output, 1 USB Ports for front Connectivity, 1 Audio for PC, 1 Audio in for Visualizer, 2 x Audio out, 1 x Projector Power, 1 x Screen Power. The Interactive Monitor touch should work independently for the both Laptop and PC. Whichever source is selected PC/Laptop when both are connected to the Podium the content should appear on Interactive Panel along with touch activated of the selected source, automatically without detaching or attaching a cable. Sound card with 2 x Input, Additional Ports: On the left side of the podium. 1 x Power Plug, 2 x USB 2.0, 1 x HDMI, 1 x VGA, 1 x LAN, 1 x Mono, 1 x Audio Video. Connectivity Ports at the bottom 1 x LAN, 1 x VGA, 2 x HDMI, 1 x Power Plug. Audio – 1x Gooseneck Microphone, Interactive Panel : Panel Type : Active Matrix Color TFT; Display Size :21” , Resolution : 1920 x 1080; Colors :16.7 M, Contrast :800:1; Inputs : HDMI or better input; Technology :Electromagnetic with Pen; Interface : USB; Pressure Sensitivity :2048 Levels; Data Report : 125 reports / per second; Accuracy : ±0.5mm; Max Reach Height : 8mm. Audio : 1 x Gooseneck Microphone, Approved Make- Techcom, ATDSC, Uni or approved equivalent |
| 398 | Supply and Delivery of Digital Signal Processor with 8 Mic/Line inputs, 8 Line outputs and 8 software assignable channels, configurable as Mic/Line Inputs or Line outputs. The processor shall have minimum 16 assignable & routable AEC channels. The processor shall have minimum 8x8 Dante channels and shall also support up to 128x128 Network audio channels via Dante or AES67. It shall also support POTS and SIP Softphone integration for Audio conferencing and configurable 16x16 USB Audio channels via USB-B ports supporting AV USB Bridging for software or web-based conferencing applications. The processor shall also have minimum 24 bit-A/D-D/A converters, 48 kHz Sample rate, Input frequency response of 20 Hz to 20 kHz @ +21dBu, Input dynamic range > 109.5 dB at @ +24 dBu sensitivity. The processor shall support third party device control via Ethernet, RS232 and GPIO and shall have front panel display for control and indicators for device status.. Approved Make- QSC, Symetrix, Biamp or approved equivalent |
| 399 | Supply and Delivery of 6-inch, 2-way Ceiling-mount loudspeaker. Frequency Range-65 Hz to 20 kHz, Rated noise power/Voltage -30 watts / 15.5 volts (rms), Sensitivity-89 dB SPL, Coverage- 110° conical, Maximum continuous SPL-104 dB, Maximum peak SPL- 110 dB, LF Transducer - 6-inch Polypropylene cone with butyl rubber surround woofer, HF Transducer-0.86-inch silk dome tweeter, Nominal impedance- 8?, Transformer Taps- 70 V: 30, 15, 7.5, 3.7, 1.9 watts, 100 V: 30, 15, 7.5, 3.8 watts. Galvanized steel Back can. All Mounting accessories included. Approved Make: QSC / Meyer / d&b or approved equivalent |
| 400 | Supply and Delivery Of Column surface-mount loudspeaker. Transducer- (x16) 2.75 in (69.8 mm) weather treated paper cone woofer. Frequency range- 90 Hz – 17 kHz, Rated noise power / voltage- 200 watts / 40 volts (rms). Transformer Taps 120w, 60w, 30w, 15w at 100 volts, 8 ohm direct, Ingress Protection - IP-54. Powder coated aluminum enclosure. Powder coated aluminum grille. All Mounting accessories included. Approved Make: QSC / Meyer / d&b or approved equivalent |
| 401 | Supply and Delivery of 8-Channel Class-D Network Amplifier. Total Power - 4000W which can be asymmetrically distributed across amplifier channels. Max Power/Channel at 16? -500W, 8?/4?-1000W, 2?-800W, 70V/100V - 1000W. Amplifier shall support Bridge and Parallel modes for combining multiple channels. Typical Distortion- 8 ?-0.02 - 0.05%, 4 ?-0.04 - 0.1%, Frequency Response (8 ?)-20 Hz - 20 kHz +0.2 dB / -0.7 dB, Noise Weighted output muted->104 dB, Gain (1.2 V setting) -38 dB, Input impedance->8k balanced and >4k unbalanced, 8 Routable Mic/Line Input Channels for Network Audio transmission, GPIO ports for control. Controls and indicators (front)-Power, Channel MUTE buttons, Channel SELECT buttons, Channel Input signal and CLIP LED Indicators, Channel Output and LIMIT LED meters, NEXT, PREV, ID buttons, Control knob. Ethernet Ports - 2 Gigabit ethernet ports for Audio, Control transport and network redundancy. Amplifier shall be compatible with the mentioned DSP processor. Approved Make: QSC / Lab Grupen/ PowerSoftor approved equivalent |
| 402 | UCI License - Supply of software license for mentioned processor to create and integrate custom user interface for control. It should allow a user to create customizable buttons, animated page transitions, and custom graphics, including backgrounds, corporate logos, system diagrams, etc. License should allow connecting Wall/Table mount Touch Panels or iOS/Windows devices as touch panel for control. License shall be perpetual and should not have any limit on no of devices to be used as Touch Controller. Scripting License - Supply of software license for mentioned processor to enable the third-party device control via Ethernet, RS232, GPIO and IR. It shall allow the use of third-party control modules/Plug-ins and custom scripts to control the devices. It shall allow open-source scripting language for writing custom scripts. License shall be perpetual and should not have any limit on no of devices to be controlled. Approved Make- QSC, Symetrix, Biamp or approved equivalent |
| 403 | Supply and Delivery of 25.91 cm / 10.2-inch (diagonal) LED-backlit Multi-Touch display with IPS technology, 2160x1620-pixel resolution at 264 pixels per inch (ppi), True Tone display, 500 nits brightness, Fingerprint-resistant oleophobic coating, 64-bit ARM-based system on a chip (SoC), Max. CPU clock rate 2.65 GHz, 7 nm A64 ARMv8.4-A, Wi-Fi (802.11a/b/g/n/ac); dual band (2.4GHz and 5GHz); HT80 with MIMO, Bluetooth 4.2 technology, Digital video output VGA, HDMI and DVI output supported using adapters, Supported formats include HEVC and H.264 Supports Dolby Vision and HDR10 content, Approved Make- Lenovo, Apple, Samsung or approved equivalent |
| 404 | Supply and Delivery of Panel Size: 98\\"\\",Type/Tech:,,TFT LCD Module with DLED Backlight.,Display Area (mm):,,2171.85(H) x 1232.35(V) (97.52”diagonal)Aspect Ratio:,,16:9,Native Resolution:,,UHD 3840x2160(Pixels),Colours:,,1.07B colours (10bit),Brightness:,,350 nits (typ.),Contrast Ratio:,,5000:1 (DCR),Response Time:,,6ms,Viewing Angles: ,,H = 178, V = 178 typ.,Backlight Life:,,30,000 Hours (Min),Surface Treatment:,,Anti-Glare, Orientation: Landscape,Processor: ARM Cortex A73*2(1.5GHz)+A53*2(1.2GHz),RAM: 3GB DDR4, Storage: 16GB,Type/ Tech:,,IR Recognition,Touch Resolution:,,32767 x 32767,Touch Point:,,20 points touch, 10 points writing, Temperature (º C):0°C to 40°C,Humidity:,,10% ~ 90% RH non-condensing, Voltage:100-240VAC +/- 10% Wide Range. Approved Make- Viewsonic, Prysm, Christie or approved equivalent |
| 405 | Supply and Delivery of Display Panel Size: 55\\", Type/ Tech: \\"TFT LCD Module. IPS type, DLED backlight\\", Display Area (mm): 1209.6 (H) x 680.4 (V) (55” diagonal), Native Resolution: 3840 x 2160, Aspect Ratio: 16:9, Colors: 1.07B colors, Brightness: 400 nits (typ.), Contrast Ratio: 1200:1 Typ., Response Time: 8 ms, Viewing Angles: H = 178, V = 178 typ., Backlight Life: 30,000 Hours Min, Surface Treatment: Anti-Glare, 2H, Haze 3%, Bezel Slim, Orientation: Landscape, HDMI: x2, DVI: x1, Audio: x1 (3.5mm), RS-232: x1, IR Pass Thru: x1, Audio: x1 (RCA), SPDIF: x1 (Fiber),IR Pass Thru: x1,RJ45: x1, USB Type A: 2.0 Type A : x2 (USB Playback), SPEAKERS: 10Wx2, RGB PC/HDMI PC: Up to 1920x1080@60Hz. Refer to timing table, HDMI: 480i, 480p,720p,1080i,1080p, 4K2K@60Hz, DVI: 480i, 480p,720p,1080i,1080p, Android Version: Android 8.0, Voltage: 100-240 VAC +/- 10% Wide Range, Consumption: Normal 100 W, Max 114.5 W, Wall Mount (VESA® ): 400x200 mm, OPERATING CONDITIONS Temperature (º C): 0 to 40°C, Humidity: 20% ~ 80% non-con DIMENSIONS (W x H x D), Physical (inch / mm): 48.94 x 28.11 x 2.94 in/1243.2 x 714 x 74.8 mm, Packaging (inch / mm): 55.90 x 35.83 x 9.65 in/1420 x 910 x 245 mm, Net (lb / kg): 16.8 kg / 37.04 lbs, Gross (lb / kg): 23.95 kg / 52.8 lbs. Approved Make- Viewsonic, Prysm, Christie or approved equivalent |
| 406 | Supply and Delivery of HDBaseT Receiver for HDMI, Ethernet, power, control, and USB, USB 2.0 (Maximum Data Rate 120 Mbps) interfacing and extension up to 330 feet (100 meters),4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling,HDCP 2.2 compliant,Remote powering over HDBaseT. Approved Make-Lightware, QSC, Atlona or approved equivalent |
| 407 | Supply and Delivery of 5×2 AV matrix switcher with HDMI, Native wireless casting for iOS, Android, Mac, Chromebook, and Windows, DisplayPortTM, and USB-C inputs,USB-C input for AV, data, and device charging,HDBaseTTM and HDMI outputs with selectable AV switching modes ,USB 2.0 interfacing and extension up to 330 feet (100 meters) ,4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling on local ports (HDMI, DisplayPort, and USB-C) ,Selectable 4K to 1080p downscaling. Approved Make- Atlona, QSC, Lightware or approved equivalent |
| 408 | Supply and Delivery of 1×2 HDMI® distribution amplifier,4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats,HDCP 2.2 compliant,EDID management,Supports cascading up to eight units Approved Make- Atlona, QSC, Lightware or approved equivalent |
| 409 | Supply and Delivery ofcHDMI Extender Kit which supports resolutions up to 4K/UHD 60 Hz 4:2:0,Remote power, transmitter powers receiver over HDBaseT,EDID filtering prevents extension of unsupported resolutions ,HDBaseT link test verifies cable, termination, and link quality,HDCP 2.2 compliant Approved Make- Atlona, QSC, Lightwarerr approved equivalent |
| 410 | Supply and Delivery of Full HD PTZ Camera supporting 1080p at 60 Frames per Second, minimum 12X Optical Zoom, with IP, HDMI, USB 3.0 & 3G-SDI Output, min 256 Presets, RS232/422 and IP Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle , Minimum FoV 72 deg,Should support PoE & should be compatible with Virtual USB Driver. OEM should be BIS, CE,RoHS & FCC Certified Approved Make- Lumens, QSC, Atlona or approved equivalent |
| 411 | Supply and Delivery of metalic Cable cubby, with passthrough cable hole |
| 412 | Supply and Delivery of 10 Port AV over IP Compatable, POE+ Switch with TOTAL POE BUDGET 125W, PORT TYPE with POE+ PORTS 8 x 1G, 2 x 1G, 2x SFP Approved Make- Dell, QSC, Netgear or approved equivalent |
| 413 | Supply and Delivery of 12 U 800 x 600 Network rack with Lockable wheels, front glass door, dual fan and required power socket Approved Make- Valrack, Comrack, President or approved equivalent |
| 414 | Supply and Delivery of Speaker Cable – 1.5 Sqmm x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. Approved Make- Belden, Molex, Krystals or approved equivalent |
| 415 | Supply and Delivery of 18 AWG (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. Approved Make- Somer, Belden, Krystalsor approved equivalent |
| 416 | Supply and Delivery of CAT 6 STP network cable Approved Make- D-Link, Belden, Molex or approved equivalent |
| 417 | Supply and Delivery of HDMI Cables 3mtr Approved Make- Somer, Kramer, Belden or approved equivalent |
| 418 | Supply and Delivery of HDMI Cables 10mtr Approved Make- Somer, Kramer, Belden or approved equivalent |
| 419 | Supply and Delivery of XLR connectors, RJ45 Connectors and other connectors and interconnects Approved Make- Neutrik, Amphanol, Switchcraft or approved equivalent |
| 420 | Providing and fixing following size of PVC casing and caping on surface as required. Note: Only ISI marked caping and casing shall be used. - 25 mm x 10 mm |
| 421 | Installation, Testing, commisioning, Programming as per the satisfaction and direction of Engineer in Charge |
| 422 | (B). Meeting Room Audio and Video Solutions |
| 423 | Supply and Delivery of Panel Size:75\\",Type/Tech:TFT LCD Module with DLED Backlight.,Display Area (mm):1650.24mm(H) x 928.26mm(V) 74.6” diagonal Aspect Ratio:16:9,Native Resolution:UHD-3840x2160(Pixels) ,Colours:1.07B colours (10bit),Brightness:350 nits (typ.),Contrast Ratio:5000:1 (DCR),Response Time:6ms,Viewing Angles:,,H = 178, V = 178 typ.,Backlight Life:30,000 Hours (Min),Surface Treatment:Anti-Glare, Orientation:Landscape,Processor:ARM Cortex A73*2(1.5GHz)+A53*2(1.2GHz) ,RAM:3GB DDR4, Storage16GB,Type/ Tech:IR Recognition,Touch Resolution:32767 x 32767 ,Touch Point: 20 points touch, 2 points writing, Touch response time ?10ms Scan Rate: 100Hz Speaker 10w x 2 Embedded OS Android, Preloded Basic Annotaion Software Whiteboard, Wireless Presentation pre loaded android marketpalce for essential apps supports Built in VC Software with USB HOST port, with ( Temperature (º C):0°C to 40°C,Humidity:10% ~ 90% RH non-condensing, Voltage:100-240VAC +/- 10% Wide Range. Approved Make- Viewsonic, Prysm, Christie or approved equivalent |
| 424 | Supply and Delivery of Speakerphone with USB, Bluetooth, and analog audio connectivity;360-degree coverage captures voices in up to a 16 foot (5 meter) radius;6-element microphone array focuses audio pickup and suppresses background noises,Sophisticated acoustic echo cancellation and noise reduction,Elegant metal enclosure suitable for conference rooms, executive offices, and home offices.Microphone Frequency Response : 150Hz – 8kHz, Speaker Maximum SPL - 80 dB SPL @ 1m, Speaker Frequency Response : 150Hz – 16kHz, Maximum Data Rate : 2.5 Mbps, USB Ports : 1 x Type C USB & 1 x USB 2.0 Daisy Chain upto 2 Speakerphone Approved Make- Atlona, QSC, AudioTechnica or approved equivalent |
| 425 | Supply and Delivery of Full HD IP PTZ Camera with a 1080p 60fps PTZ camera with 12x zoom, HDMI, 3G-SDI, USB, and IP streaming. Approved Make- Lumens, QSC, Atlona or approved equivalent |
| 426 | Supply and Delivery of HDBaseT Transmitter and Receiver for HDMI, Ethernet, power, control, and USB, USB 2.0 (Maximum Data Rate 120 Mbps) interfacing and extension up to 230 feet (70 meters),4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling,HDCP 2.2 compliant,Remote powering over HDBaseT. Approved Make-Lightware, QSC, Atlona or approved equivalent |
| 427 | Supply of HDMI Cables 5mtr Approved Make- Somer, Kramer, Beldenr approved equivalent |
| 428 | Installation, Testing, commisioning, Programming as per the satisfaction and direction of Engineer in Charge |
| 429 | (C ). Common Area and PA System |
| 430 | Supply and delivery of EN-54 Certified Digital microprocessor-controlled voice alarm compact amplifier for voice alarm, announcements and background music. Integrated audio inputs, 8-level priority control, voice alarm control, power amplifier, circular dial and complete monitoring according to VDE 0833-4 and VDE 0828-1. 6 switchable and adjustable volume speaker outputs with a total of 360 Watt of rated output. Three microphone / audio carrier inputs with switchable sensitivity as well as two stereo audio carrier inputs with volume control and tone control on front panel, one input switchable sensitivity and volume control back to prevent an intentional or unintentional adjustment, two speaking bus lines for up to four external stations. Front mounted acoustically and electrically monitored fire brigade microphone (fist microphone) with control panel for controlling the alarm: emergency one and out, range selection, selection of evacuation and warning text. Fault indication with plain text display of the occurred error, acoustic signal and reset button. Password-protected setting the equalizer settings, language, password many more. and display relevant system information via menu on alphanumeric two-line display. LAN connection for system programming and read out of the log with detailed event and error messages to diagnose locally or to remote diagnosis. 8 universally usable inputs and 8 universally usable control outputs; 6 separate inputs for alarm control of the BMZ with switchable monitoring, one with 24-volt control (polarity); three separate control outputs with relay contacts for feedback to the BMZ: collective fault signal (changeover contact), emergency (changeover contact) and activated CPU off (make contact). Each line output a switching relay for example external volume control in 3- and 4-wire technology. The userfriendly multilingual programming software on Windows(R)is included. Power supply: 230 V ~, 24 V DC, Frequency response: 50-20000 Hz, Sensitivity inputs 1-4: 10 / -50 dBV, Receiver. Background music:-10 dBV, Noise ratio: 85 dB Approved Make- TOA, QSC, Lapgrupen or approved equivalent |
| 431 | Supply and delivery of Digital station in the attractive design with Gooseneck microphone and wind to connect to a Digital controller of management. The keypad is easy to identify acceptable labelling Strip and easy to clean. 10 programmable buttons with activation indicator led for area and text option from the text store. Digital control signals, audio signals, and power supply via bus line. Input socket for external power supply, socket for connecting a headset speaking with preload for electret microphones. Integrated Mic Preamps with switchable compressor and adjustable microphone sensitivity, floating balanced output. Automatic triggering of a pre and/or post gongs from 4 different 1-4 sound effects by the talk button can be programmed, display by LED during the Gong. Operational, engaged and talking advertisement for activation. Intercom station without additional accessories as a built-in intercom can be used. The number of buttons can be increased through a keyboard extension. Monitoring speaking points connecting to the ELA management amplifier. Indicator for connection failures to the ELA management system. Output level: 0 dBV into 600 ohm Frequency response: 100-10,000 Hz Microphone: electret microphone on Swan neck, Cardioid Connection cable: Category 5 cable with RJ45 connectors, Approved Make- TOA, QSC, Audio Technicaor or approved equivalent |
| 432 | Supply and delivery of the booster amplifier shall operate on 220 – 240 V AC or 24 V DC power, and shall control and mix 1 balanced (screw terminal) Line in and 1 unbalanced (screw terminal) 100 V Line inputs. Outputs shall be balanced Loop out and balanced high and low impedance (floating) Speaker out. The amplifier shall meet the following performance criteria: Power output shall be 240 W at less than 1% THD (at 1 kHz, 1/3 rated power). Frequency response shall be 50 Hz to 20 kHz (+/-3 dB), with an S/N ratio of over 60 dB. Bass Tone Control shall be +/-10 dB at 100 Hz, and Treble Tone Control shall be +/-10 dB at 10 kHz. It shall be possible to bypass the master volume to make emergency announcements. Power, signal and peak indicators, and fan cooling ventilation shall be provided. The panel shall be ABS black resin, and the case black steel plate. Approved Make- TOA, QSC, Lapgrupenor approved equivalent |
| 433 | Supply and delivery of 6 W (100 V line), 3 W (70 V line), Rated Impedance,,100 V line: 1.7 k? (6 W), 3.3 k? (3 W), 10 k? (1 W), 70 V line: 1.7 k? (3 W), 3.3 k? (1.5 W), 10 k? (0.5 W), Sensitivity 90 dB (1 W, 1 m) (500 Hz - 5 kHz, pink noise), Frequency Response 100 Hz - 18 kHz (peak -20 dB), Speaker Component 12 cm (5\\"\\") cone-type Approved Make- TOA, QSC, Tanoy or approved equivalent |
| 434 | 10 W Volume Control for Cabins |
| 435 | Supply and delivery of Horn Speaker; Rated Input 5;10;15;30W;100V Frequency Response 250Hz ~10kHz; SPL (1W / 1m) 113dB (500 to 2,500 Hz peak level) Dimensions 285x227x277 mm, IP65, 2 kg Approved Make- TOA/Tannoy/Pro Acoustics USA or approved equivalent |
| 436 | Supply and Delivery of Display Panel Size: 55\\", Type/ Tech: \\"TFT LCD Module. IPS type, DLED backlight\\", Display Area (mm): 1209.6 (H) x 680.4 (V) (55” diagonal), Native Resolution: 3840 x 2160, Aspect Ratio: 16:9, Colors: 1.07B colors, Brightness: 400 nits (typ.), Contrast Ratio: 1200:1 Typ., Response Time: 8 ms, Viewing Angles: H = 178, V = 178 typ., Backlight Life: 30,000 Hours Min, Surface Treatment: Anti-Glare, 2H, Haze 3%, Bezel Slim, Orientation: Landscape, HDMI: x2, DVI: x1, Audio: x1 (3.5mm), RS-232: x1, IR Pass Thru: x1, Audio: x1 (RCA), SPDIF: x1 (Fiber),IR Pass Thru: x1,RJ45: x1, USB Type A: 2.0 Type A : x2 (USB Playback), SPEAKERS: 10Wx2, RGB PC/HDMI PC: Up to 1920x1080@60Hz. Refer to timing table, HDMI: 480i, 480p,720p,1080i,1080p, 4K2K@60Hz, DVI: 480i, 480p,720p,1080i,1080p, Android Version: Android 8.0, Voltage: 100-240 VAC +/- 10% Wide Range, Consumption: Normal 100 W, Max 114.5 W, Wall Mount (VESA® ): 400x200 mm, OPERATING CONDITIONS Temperature (º C): 0 to 40°C, Humidity: 20% ~ 80% non-con DIMENSIONS (W x H x D), Physical (inch / mm): 48.94 x 28.11 x 2.94 in/1243.2 x 714 x 74.8 mm, Packaging (inch / mm): 55.90 x 35.83 x 9.65 in/1420 x 910 x 245 mm, Net (lb / kg): 16.8 kg / 37.04 lbs, Gross (lb / kg): 23.95 kg / 52.8 lbs Approved Make- Viewsonic, Prysm, Christie or approved equivalent |
| 437 | Supply and delivery of CAT 6 network cables Approved Make: D-LINK/MOLEX/KRYSTALS or approved equivalent |
| 438 | Supply and delivery of 2.5sqmm x 2 core ATC Vasiform Approved Make: BELDEN/Somer/KRYSTALS or approved equivalent |
| 439 | Supply and delivery of 12U Rack Aproved Make: Valrack/Comrack/President or approved equivalent |
| 440 | Installation, Testing, commisioning, Programming as per the satisfaction and direction of Engineer in Charge |
| 441 | SUPPLY & FIXING OF PVC CASING / CAPING |
| 442 | 25 MM X 10 MM |
| 443 | PART-I: AUTOMATION SYSTEM |
| 444 | Providing & Fixing iTouch Series 4 Buttons Touch Panel EU , with Aluminum Frame, used to control lighting,curtain and scene, LED backlight and LED indicator (Crabtree Model No .ACBAX009 OR Approved equivalent) |
| 445 | Providing & Fixing of Granite Display Panel EU, with 4-inch LCD screen and Aluminum plate, used to control lighting, curtain, scene, air conditioning, floor heating, music and fresh air, Built-in temperature sensor, humidity sensor and proximity sensor, (Crabtree Model No. ACBAA074 or Approved Equivalent) |
| 446 | Providing & Fixing of Panel Power Interface EU,provides DC power and communicates to the Wall panel, (Crabtree Model No. ACBAF005 or Approved equivalent) |
| 447 | Providing & Fixing of 64CH DALI Ballast Dimming Actuator, DIN-Rail Mount,with built in DALI power supply and single DALI bus.The unit can also support 64 DALI ballasts, and scene control. The scene control allows the creation of 16 areas, with each area having 16 scenes (Crabtree Model No. ACBAA042 or approved equivalent) |
| 448 | Providing & Fixing of 12CH 10A High Power Switch Actuator, DIN-Rail Mount, 10A per Channel, 16A Magnetic latching relay, With scene and sequence controller (Crabtree Model No. ACBAA007 or approved equivalent) |
| 449 | Providing & Fixing of Logic Automation Module, provides centralised control over a range of targets. The module is capable of accepting 12 logic types, and has in total 960 logic blocks. The logic conditions enable the input of date and timing information, universal switch states, and external inputs. (Crabtree Model No. ACBAS001 or approved equivalent) |
| 450 | Providing & Fixing of 1 Port Programming Gateway, enables communication through an Ethernet connection or internet connection (Crabtree Model No. ACBAT001 or approved equivalent) |
| 451 | Providing & Fixing of 2400mA Power Supply Module, 110V/220V AC Input 50-60Hz, DC24/2400mA output, (Overheat, Overload, Surge Protection) (Crabtree Model No.ACBAU002 or Approved equivalent) |
| 452 | Providing & Fixing of 8 in 1 Network Sensor, includes PIR motion sensor, temperature sensor, LUX sensor, dry contact,etc. (Crabtree Model No. ACBAJ002 or approved equivalent) |
| 453 | Providing & Fixing of Smart IR Transmitter, 200 infrared codes can be stored in it. The software can program and use the IR codes to control the IR device, such as TV, DVD, AC, Amplifier etc for the 3rd flr conference room (Crabtree Model No.ACBAR001 or approved equivalent) |
| 454 | Providing & Fixing of wiring Accessories DB, MCB, SPD, Cat6 cable etc as per requirement. |
| 455 | Installation & Programming Charge |
| 456 | PART:J FAÇADE LIGHTING |
| 457 | SITC of high quality long through multi color spot light, Protection Rating : IP65, complying to BIS standard IS 10322 (Part 5/Sec 1): 2012, and having CE certification against standard EN 61547: 2009, EN 60598-1:2015, and EN 61347-2-13:2014 MountingStructure : Additional wall mount yoke arrangements for fixing the lights. Rotation view: Inbuilt body rotating angle in degrees for uniform rotation angle to get the desired effect. Power consumption : 20W, CCT : RGBW, (as per the design approval) Beam Angle25º/45º/60º, Control DmX512/ON/OFF, Channel : 4 CH, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots &fringing in color mixing applications. Power Input : AC 110-230V, 50Hz or DC12/24V withexternal driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement) Glare : Specially designed glare freeround shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass sealed above the glare free unit. Painting : 7 tank processed chemical treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade with total protection class of IP 65 . Luminaire is inclusive of Integral male/female waterproof connectors , driver, accessories for fixing ( nut , bolt , clamps etc ) with structures in pre wired conditions as per IS. Light testing standardshould be LM79, LED Driver, IP65 or higher, IK05 or higher etc., LED Makes should beCREE/ Lumileds, OSRAM, Seoul, Philips Approved Make: Leksa Lighting/iGuzzini/Color Kinetics/Pulsar or Approved equivalent |
| 458 | Supply of high quality Linear Profile light, Protection Rating : IP65, Power : 15W, 17mm (With front diffuser), CCT : RGBW. Beam Angle 120º. Body : Extruded aluminium. Power Input : DC 24V (without DC Driver) Code: LK LW 15 RG |
| 459 | SITC of high quality long through multi color linear wash light, Protection Rating : IP65,complying to BIS standard IS 10322 (Part 5/Sec 1): 2012, and having CE certification against standard EN 61547: 2009, EN 60598-1:2015, and EN 61347-2-13:2014 Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : Inbuilt body rotating angle in degrees for uniform rotation angle to get the desired effect. Power consumption : 80W, CCT : RGBW, (as per the design approval) Beam Angle 25º/45º/60º, Control : DmX512/ON/OFF, Channel : 4 CH, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC 110-230V, 50Hz or DC12/24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement) Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass sealed above the glare free unit. Painting : 7 tank processed chemical treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade with total protection class of IP 65 . Luminaire is inclusive of Integral male/female waterproof connectors , driver, accessories for fixing ( nut , bolt , clamps etc ) with structures in pre wired conditions as per IS. Light testing standardshould be LM79, LED Driver, IP65 or higher, IK05 or higher etc., LED Makes should be CREE/ Lumileds, OSRAM, Seoul, Philips Approved Makes: Leksa Lighting/iGuzzini/Color Kinetics/Pulsar or Approved Equivalent |
| 460 | SITC of Power Driver for above lights, POWER : 200W, INPUT : AC 110-240V AC, 50HZ, OUTPUT : DC 24V, Protection rating IP66,Constant Voltage (C.V.) + Constant Current (C.C.) output, High efficiency up to 93%, Working temperature (case temperature)- 45~+45°C, Protections: Short circuit / Over current / Over voltage / Over temperature, Comply with harmonic current limit per EN61000-3-2 Class C (?50% load), Meet 4kV surge immunity level. |
| 461 | SITC of PVC insulated multi core electrical un armored flexible 3C x 2.5Sq mm power cable having less electrical losses. This PVC insulated and round sheathed wire features a bright multi strands copper conductors and it supports voltage grade up to 1100V. (As per actuals depending upon the site condition) |
| 462 | SITC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. (As per actuals depending upon the site condition) |
| 463 | SITC of Power Distribution Electrical panel having a Incomer of 32A. Floor mount / rack mount / wall mount. Miniature circuit breakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures. Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V confirming to IS 694 and IS 8130 All welding slag grounded off and welding pits wiped smooth with plumber metal. Power panels shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component does not attain temperature more than 40 degree Celsius. Fabricated panel shall be supported with ms angles of size 25mm x 25mm with an 1.8mm thickness sheet to hold the structure. Individual MCB control for 12 outgoing circuits |
| 464 | SITC of IP65 \\"I\\" power connectors having 3/4 pole cable connector, chuck type strain relief, Current rating 20 A rms continuous, Easy and extremely precise locking system \\"Quick Lock\\" High impact materials - long-lasting and reliable |
| 465 | SITC of IP65 \\"I\\" DMX connectors having 3/5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. |
| 466 | Supply, laying clamping and installation. 25mm PVC / FRPP Conduits.(As per actuals depending upon the site condition) |
| 467 | SITC of 5 pin XLR Male connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. |
| 468 | SITC of DMX 512 address writer for changing the color combination of the facade as per the design or site requirement. |
| 469 | SITC of DMX isolator or splitter provides Isolated optical DMX splitter provides 8 outputs from a 1 input and Input voltage: AC 110 to 220 V, 50 Hz, Product features: Group 1 & group 8 DMX signal change. Approved Makes: Lite Puter / Leksa Lighting / Elation or Approved equivalent |
| 470 | Providing earthing with galvanised iron earth plate, Eathing pipe, GI earthing wire, complete with all materials, testing and recording the result as per specification no EA EP(9-1-1)(2018-2019) |
| 471 | SITC of high quality DMX decoder, Power Input : DC 24V, Protection rating : IP65. |
| 472 | SITC of waterproof power junction box /power cable terminal box, IP65 made up of rugged, non-corrosive, high impact polycarbonate, molded nylon encases connectors that use screw compression to secure the wires, protection against water jets and dust from all directions, includes 5 Way min 10A connector terminal block Max. dimension : 80 * 250 * 85mm Approved Makes: L&T / Leksa Lighting / Siemens or Approved equivalent |
| 473 | Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc.for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.(6-1-19)(2018-19) |
| 474 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. |
| 475 | PART-K: SOLAR PANEL |
| 476 | PROVIDING, ERECTION, INSTALLATION, COMMISSIONING WITH 5 YEARS WARRANTY OF 20 KW SOLAR ROOFTOP POWER PLANT \\"300Wp to 335Wp,72 cell, IEC Certified Multi crystalline Solar module \\" \\"20Kw grid tied string inverter Out put AC 415 volt +/- 10% 3phase 50 Hz \\" \\"Array junction box/DCDB as Per MNRE Stnd. \\" \\"20kw LT panel box MNRE Stander 20kw LT panel box MNRE Stander 20kw LT panel box MNRE Stander \\" \\"4 sq. 1core DCcopper cable For module inter connection 4 sq. 1core DCcopper cable For module inter connection \\" \\"6sq. 4core armoured CU cable \\" Installation accessory 20mm PVC pipe & accessory 25sq mm flexable pipe CU lugs Lighting arrester 3mt CU bonding rod Chemical Gel earthing kits Pvc earth pit cover 20 x 3 mm GI Strips \\"HDGI 80 micron( ESPL) 50 x 50 x 5 mm each leg 40 x40 x 5 mm for each cross member Purlin, mild steel hot deeped Galvanized module structure 180 wind load without any vibration \\" \\"Civil work for fixing (included) \\" Installation & Commissioning |
| 477 | PART: L GREEN BUILDING |
| 478 | GRIHA Facilitation (Green Building) as per the scope of work |
| 479 | PART-M: 5 KLD STP |
| 480 | Design ,Supply, installation and commissioning of MS Fabricated Sewage Treatment Plant Tanks of Screen Chamber, MBBR, Settler and Filter Feed with all initial leads, Drains, Pump connection fittings and liftings hooks. Capacity of the whole system must be 5 m3/D treatment and the thickness of the tank must be 6mm for both bottom and side wall. The proposed tanks must be internally finished with FRP and externally finished with 2 coats of Zinc chromate primer and single coat of Enamel painted. Tanks must be covered with steel roof shelter. The rate should be inclusive of all inclusive of all incidental charges transport to site, loading, site, unloading etc. inline with Contract terms and conditions and specifications. |
| 481 | PART-N: FURNITURE WORKS |
| 482 | Providing and placing in position Godrej make Model: La Sede or Approved equivalent, with, 1) SEAT ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45+2 kg/m3, and hardness load 16 + 2 kgf as per IS:7888 for 25% compression. *Seat Size : 47.6 cm. (W) x 49.2 cm. (D). 2) BACK ASSEMBLY: The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Table of size 1.9+0.03cm x 0.16 + 0.0128 cm. It upholstered with Pure Leather. *High Back size: 47.5 cm. (W) x 77 cm (D). 3) ARMRESTS : The armrest top should be moulded from polyurethane (PU) uphlstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81+0.03 cm x 0.2+0.01 cm thk M.S. E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5+0.5cm in 5 steps. 4) ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanish should be designed with the following features: * 360 degree revolving type. * Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. * Tilt tension adjustment can be operated in seating position. * 5-position Tilt limiter giving option of variable tilt angle to the chair. * Seat/back tilting ration of 1:2. * The mechanism housing should be made up of HPDC Aluminium black powder coated. 5) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0+0.5 cm. 6) ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.4+0.5 cm for the comfortable back support to suit individual need. 7) PNEUMATIC HT. ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 10.0+0.3 cm. 8) PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0+0.5 cm. 9) TWIN WHEEL CASTOR : 5 nos. twin wheel castors shall be injection moulded in plastic having 6.0+0.1 cm wheel Diameter and assembled to pedestal. |
| 483 | Providing and placing in position Godrej make Conference Chair, Model : Motion Mid Back or Approved equivalent with Adjustable Armrest, Seat Back Assembly : The cushioned seat base moulded in glass-filled Poly - amide. moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high strech knitted polyester fabric. Mid Back Size : 44.0cm W x 46.0cm H & Seat Size : 48.5 cm W x 47.0 cm D. High Resilience (HR) Polyurethane Foam : The HR polyurethane foam used in seat and back cushion in moulded in Density 45+2 kg/m3, and hardness load 16+2 kgf as per should be : 7888 for 25% compression. Tilt Mechanism, Spines & Spine connector : The seat and back shall be firmly connected to the base frame and shall be cantilevered in such a way that it gives a multi - dimensional movment possibillity just with a impact cushioning while sitting and synchronises with the back movement during posture changes. The \\"S\\" poly -amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which should be inbuilt in seat base and the tension (return force) should be user weight dependent. Fixed Armrest : The assembly should be having Fixed arm rest structure moulded in glass-filled Poly-amide. The Armrest Top should be made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. Pneumatic hight adjustment : The seating height can be adjusted with a pnenmatic gas-lift having an adjustment stroke of 9.2 + 0.3 cm.Pedestal Assembly : The pedestal should be injemoulded should be glass-filled Poly-amide and fitted with 5 nos. win wheel diameter and assembld to the pedestal. |
| 484 | Providing and placing in position Godrej make Glaze Corner Table or Approved equivalent with table legs meterials size : Ovel metal tube. Thicks 1.5 mm L X W X T Size : 1100 X 600 X 800 MM. Color : Partial black temered glass topfull black tempered glass. Full black tempered glass. Partial black glass & silver power coating frame and legs. |
| 485 | Providing and placing in position Godrej make Sofa - Model - Pisa 3 seater sofa or Approved equivalent: The seat should be made of PU foam with Density 32 +/- 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 +/- 2 kg/cu. Seat should upholstered with fabric or leatherette based on our approval. The back should be made of PU foam with Density 28 + 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23+/- 2 kg/cu. mtr, upholstered with fabric or leatherette based on our approval. Understructure should be made up of 1.2+/- 0.1 cm. thick hot pressed plywood, with Dia 4mm zigzag spring assembly should be mounted in under structure for support and additional cushioning purpose. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. The dimension of Sofa would be:206.0cm(W)*90.5cm(D)*85.5.0cm(H), Seat Ht. 45cm. |
| 486 | Providing and placing in position Godrej make Sofa - Model - Pisa 2 seater sofa or Approved equivalent: The seat should be made of PU foam with Density 32 +/- 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 +/- 2 kg/cu. Seat should upholstered with fabric or leatherette based on our approval. The back should be made of PU foam with Density 28 + 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23+/- 2 kg/cu. mtr, upholstered with fabric or leatherette based on our approval. Understructure should be made up of 1.2+/- 0.1 cm. thick hot pressed plywood, with Dia 4mm zigzag spring assembly should be mounted in under structure for support and additional cushioning purpose. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. The dimension of Sofa would be:146.0cm(W)*90.5cm(D)*85.5.0cm(H), Seat Ht. 45cm. |
| 487 | Providing and placing in position Godrej make or Approved equivalent Centre Table, Model PISA or Approved equivalent and should have 10+0.3 mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It should be a welded assembly made in SS202 grade having dia. 12+0.04 as per IS:1762. |
| 488 | Providing and placing in position Godrej make or Approved equivalent Centre Table, Model Glaze Corner Table or Approved equivalent |
| 489 | Providing and placing in position Godrej make Storage, Model: Reserve HDU or Approved equivalent with Hinge Door Unit (Size : 1222W x 460D x 1200H) : Construction should be a knockdown construction of 25mm thk and 18mm thk Pre-Laminate boards with metal cladding of 0.8mm thk C.R.C.A. (as per IS: 513) from outside. Side metal cladding should be coatedwith Epoxy polyster powder of 50+/-10 microns thickness. Wooden Top should be provided which i smade of 25mm thick Pre-Laminated board. The doors shall be made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side. Two adjustable shelf, vertical partition in between. Uniformly distributed load capacity for each shelf should be 40kg maximum. 3 way nickel plated wooden furniture lock should be provided for effective and positive locking of doors. Aesthetically appeling recessed handles of Aluminium extrusion shall be provided for easy opening and closing. |
| 490 | Providing and placing in position Godrej make main table with ERU attached Pedestal,Model: Aristo (size: 2350x2350x750 MM) Office Table, Work Surface (Size : 2350W x 1150D x 750H) with Return Desk (Size: 1200W x 500D x 750D) : Made of 25mm Thick Pre-laminated twin board of E1 - P2 grade and approved shade confirming to should be - 12823 : 1990, Edge banded with maching 2 mm thick PVC lipping. Gromet provided on work surface for wire management. Modesty Panel : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Understucre : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Hinge door Storage : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Handle should be provided for ease of opening. Storage should be provided with cam with cam lock for for security. |
| 491 | Providing and placing in position Godrej make High Back Chair, Model: ACE or Approved equivalent with 1) SEAT/BACK ASSEMBLY: The Cushioned seat assembly consists of seat outer (material-30% Glass Fiber Filled Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyester fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) upholsteredwith polyester Mesh fabric.The size of the Back & seat are* FULL BACK SIZE: 46.5 cm. (W) x 60.0 cm. (H)* SEAT SIZE : 51.0 cm. (W) x 49.0 cm. (D) 2) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 +/- 2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. 3) BACK SPINE: The support spine should be made up of High Pressure Die cast polished Aluminum. 4) ARMRESTS : The armrest should be having two adjustment, Height and Depth. Height adjustment should be provided in Aluminumstructure of armrest which should be connected to Aluminum Back spine And should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.5) FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: # 3600 revolving type.# Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.# Tilt tension adjustment can be operated in seating position. # 5-position Tilt limiter giving option of variable tilt angle to the chair.Seat/back tilting ratio of 1: 2 (110 seat tilt / 220 back tilt). The mechanism housing should be made up of H.P.D.C.Aluminum black powder coated. 6) LUMBAR SUPPORT ASSEMBLY: The Lumbar suport assembly consists of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 50mm. 7) Neck-rest ASSEMBLY: The Neck-rest assembly consists of upholstered Neck-rest inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. Upholstered inner should be fixed to Neck-rest cover. Neck-rest should be fixed to Back assembly through Neck-rest spine. Neck-rest Assembly has height adjustment of 55mm And Rotation Adjustment of overall 20 degrees (i.e. +/- 10degree).8) PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 cm. 9) PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia. should be 65.0cm without castors. 10) TWIN WHEEL CASTORS: The twin wheel castors shall be injection moulded in black PP having 60mm wheel Diameter. * Note: Dimensions measured out to out extreme points on components in knocked down condition,variation within +/-0.5. |
| 492 | Providing and placing in position Godrej make Visitor Chair, Model: ACE or Approved equivalent with 1) SEAT/BACK ASSEMBLY: The Cushioned seat assembly consists of seat outer (material-30% Glass Fiber Filled Nylon) & upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyester fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) upholsteredwith polyester Mesh fabric.The size of the Back & seat are* FULL BACK SIZE: 46.5 cm. (W) x 60.0 cm. (H)* SEAT SIZE : 51.0 cm. (W) x 49.0 cm. (D) 2) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 +/- 2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. 3) BACK SPINE: The support spine should be made up of High Pressure Die cast polished Aluminum. 4) ARMRESTS : The armrest should be having two adjustment, Height and Depth. Height adjustment should be provided in Aluminumstructure of armrest which should be connected to Aluminum Back spine And should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. The powder coated (DFT 40-60micron) tubular frame should be cantilever type & made of dia 2.54+/-0.03 cm x 0.2+/-0.016 cm thk MS ERW tube. |
| 493 | Providing and placing in position Godrej make Aristo Table (size: 2100x2250x750 MM) or Approved equivalent. Office Table, Work Surface (Size : 2100W x 1050D x 750H) with Return Desk (Size: 1200W x 500D x 750D) : Made of 25mm Thick Pre-laminated twin board of E1 - P2 grade and approved shade confirming to should be - 12823 : 1990, Edge banded with maching 2 mm thick PVC lipping. Gromet provided on work surface for wire management. Modesty Panel : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Understucre : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Hinge door Storage : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to should be 12823:1990, Edge banded with matching 2 mm hick PVC lipping. Handle should be provided for ease of opening. Storage should be provided with cam with cam lock for for security. |
| 494 | Providing and placing in position Godrej make High Back Chair, Model: Marvel or Approved equivalent. To be made up of Injection moulded Plastic both inner and Outer. Plastic inner shall be upholstered with PUre Leather and moulded High resilience Poly urethene foam of Density =45+/- 2 KG/M3 and Hardness 162 AS PER IS:7888 for 25% compression. It will consist of PU Foam with in situ moulded MS- ERW. Round Tube size 1.9 0.03CM X0.16 0.0128. The Arm rest is made of PU upholstered PUre leather, mounted on a drop lift adj. type tubular armrest support made of 3.810.3CM dia, 0.20.01CM thk, . ERW tube having CP Finis, with height adjustment up to 6.50.5CM in 5 steps. The mechanism is designed with the following FEATURES:- 360 DEG Revolving type. Front pivot for tilting with feet resting on ground and with adjustment facility in sitting position. Seat and Back tilting Ratio, 1:2. The housing mechanism shall be Black Powder coated HPDC ALU sections. Seat depth adjustment range is of 6.00.5CM, connected to UP/DW mechanism of HD Plastic T SPINE . can be adjusted in the range of 7.42 0.5CM to suit individual need. Adjustable Stroke shall be10.00.3CM.HPDC polished Aluinium fitted with 2 No of TWIN WHEEL CASTORS. |
| 495 | Providing and placing in position Godrej make Visitor Chair, Model: Marvel or Approved equivalent It shall be made up of injection molded Plastic outer & inner . Plastic inner is ypholstered with PUre leatherE leather and moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness 162 as per is:7888 for 25% compression . It consists of PU foam with in situ moulded MS ERW PUre leather. The armrest is made of PU upholstered PUre leather ar mounted on a drop lift adj. type tubular armrest support made of 3.810.3cm x 0.20.01cm thk MS ERW tube having chrome plated finish. the armrest Height adj. up to 6.50.5cm in 5 steps.The mechanism is designed with the following features:- 360 DEG REVOLVING TYPE. Front pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment can be operated in seating position.5-position tilt limiter giving option of variable tilt angle to the chair. Seat/back tilting ratio of 1:2. The mechanism housing is made up of HPDC alu. Black powder coated. It is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.00.5cm. It is connected to up/dw mechanism house in plastic t spine . It can be adjusted in the range of 7.42 0.5cm for the comfortable back support to suit individual need.It has an adjustable stroke of 10.00.3cm.It has a high pressure die cast polished Aluminium, fitted with 2nos twin wheel castors . the pedestal pitch center is 65.0 0.5cm pitch center. (75.0 1.0cm with castors).5 no twin wheel castors are injected moulded in plastic having 6.0 0.1cm wheel dia and assembled to pedestal. It is a cantilever type and made of dia 2.540.03cm x 0.20.016 cm thk SS 202 tube . The back connected to frame through chrome plated high pressure die cast connector piece. |
| 496 | Providing and placing in position Godrej make Sofa Two Seater , Model: PARTO PLUS or Approved equivalent of Size:- W-1340X D- 870X H-730X SH-395 mm made by Soft foam for comfort, Recron filling at seat and backrest, PVC upholstery, Tropical wooden understructure of black upholstery. . |
| 497 | Providing and placing in position Godrej make Centre Table, Model: Crystalline or Approved equivalent. Center Table (Size : 1000W x 600D x 450D): 8mm tempered glass top MDF understructure with PVC covering Pu paint strip on glass top with silver powder Glass top attached to the understructure via UV disc. |
| 498 | Providing and placing in position Godrej make Executive Chair, Model: Versa Neo or Approved equivalent. HIGH BACK CHAIR WITH SEAT DEPTH ADJUSTMENT - 1) SEAT ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45+2 kg/m3, and hardness load 16+2 kgf as per IS:7888 for 25% compression. The stitched cover should be made from spacer fabric and leatherette. *Seat SIZE : 47.0 cm. (W) x 48.0 cm (D). 2) BACK ASSEMBLY: The Cusioned back should be made of PU Foam with insitu molded MS E.R.W. Round Tube of size 1.9+0.03 cm x 0.16 + 0.0128 cm. It upholstered with spacer fabric and leatherette. The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81+0.03 cm x 0.2+0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5+0.56cm in 5 steps. The Armrest structure should be powder coated (DFT 40-60 micron). 4) ACTIVE BIO-SYNCHRO MECHANISM (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: * 360o revolving type. * Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. *Tilt tension adjustment can be operated in seating position. *5-position Tilt limiter giving option of vaiable tilt angle to the chair. * Seat/back tilting ratio of 1:2. * The mechanish housing should be made up of HPDC Aluminium black powder coated. 5) SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanis. Seat depth adjustment range should be of 6.0+0.5 cm. 6) ADJUSTABLE BACK SUPPORT Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spone. It can be adjusted in the range of 7.42+0.5 cm for the comfortable back support to suit individual need. 7) PNEUMATIC HT. ADJUSTMENT : The pneumatic ht adjustment has an adjustment stroke of 10.0+0.3 cm. 8) PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.0+0.5 cm. pitch-center dia. (76.1+1.0 cm. with castors.) 9) TWIN WHEEL CASTOR 5 Nos. twin wheel castors shall be injection moulded in plastic having 6.0+0.1cm wheel Diameter and assembled to pedestal. 10) VISITOR TUBULAR FRAME : The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of O2.54+0.03 cm x 0.2+0.016 cm thk MS ERW tube. The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece. |
| 499 | Providing and placing in position Godrej make Visitor Chair, Model : Motion or Approved equivalent with Seat Back Assembly : The cushioned seat base moulded in glass-filled Poly - amide. moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high strech knitted polyester fabric.Visitor Frame Assembly : The Power (DFT 40=60 micron) tubular frame should be cantilever type & made of 0.2.54 + 0.03 cm x 0.3 + 0.016 cm thk MS ERW tube. Shoes shall be made of glass-filled Poly-amide and fixed of the tubular frame. |
| 500 | Providing and placing in position Godrej make Sofa Two Seater , Model: RIO PLUS or Approved equivalent of Size- L-1720 , H-750 , W- 800,Seat Height from ground-430 . Stitiching:- Thread - Nylon , Pitch-3-4 mm . Leather /PVC/Fabric:- PVC Frame Material- Wood Frame (SOLID RUBBER WOOD , PARTICLE BOARD , MDF) . Seat Foam - ( Density ,Type) FOAM = 30 DENSITY SOFT WITH 1\\" RECRON. Back Foam- (Density , Type )DENSITY SOFT WITH 1\\" RECRON . Belt Material-(SEAT: S-SPRING = 9 PCS. + 3 NYLON BELTS (2\\") LEG MATERIAL: Plastic Leg ,Leg DIA 50 mm. WITH M 6 NUT SET. |
| 501 | Centre Table - Round /Oval: Providing and placing Godrej Make Helix Centre Table or Approved equivalent of approx Dimensions 1100 x 600 x 460 with 10 mm tempered glass top, 8 mm tempered bottom glass for storage option. Chrome plated understructure. Having Passed 48 hours salt spray test. Glass attached to the understructure via UV disc. |
| 502 | Providing and placing in position Godrej make Book Case, Model: 4 Drawer Book Case(size: 1742x914x320 mm)or Approved equivalent Bookcase, Multi bend construction with press fit fastener free design. Door with equalizing scissor mechanism for easy opening & closing. 10 lever cam lock 330 mm clears space. Anti corrosion treated components & oven baked powder coating process.a) TOP,bottom,LH & RH sides and back material thickness=0.8 mm MS b) Removable Glass Door with 3 MM Glass(4 Nos.) with equalizing mechanism for easy operation. c) Shelves with stiffener to take more load of material thickness = 0.8 mm MS. Size:- 1875x850x760 mm. |
| 503 | Providing and placing in position Godrej make main table with ERU attached Pedestal, Ascent Desk (Size : 2100W x 1600D x 765H)or Approved equivalent having Particle-board ( Melamine Finish)25mm Top + 15mm frame; 2mm PVC Lipping on top and 0.35mm PVC Lipping on frame. MODESTY PANEL:1100X405X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping.DRAWER FRONT :500X170X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping. KBPT :578 (W) X 284 (D) X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping.ERU :1600 (L) X500 (W) x 650 (H) all panels shall be 16mm THK Particle-board ( Melamine Finish). with 0.35mm THK PVC Lipping. |
| 504 | Providing and placing in position Godrej make Filing Cabinet, Model: 4 Drawer Filing Cabinet(size: 1320x470x620 mm)or Approved equivalent with Rigid Knock Down Construction CRCA 0.7 mm Thick (Top, Side & Drawer Front); 0.6 mm Thick (Frames, Drawer- Inside Cover, Side Back Side) 0.5mm Thick (Back, Bottom, Drawer Bottom) Easy to grip Full length Handle recess integrated into Metal Drawer fronts.Snap on type plastic label holder on Drawer Fronts. For hanging #Ezee# / #Visa# files (Foolscap) from front to back (Files Along theWidth) · No. of 20 mm thk file which can be hanged in above way per drawer is 28.Centralized locking with 10 lever Cam Lock & having anti-tipping arrangement to ensure that when one drawer is opened for use, it does not allow other drawers to be opened. High quality precision ball slide. Drawer Load: 40 kg. UDL for 75,000 cycles (BS) Plain Triangular plate pop riveted at the bottom corners for rigidity. Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). |
| 505 | Providing and placing in position Godrej make mid back Chair, Model : Motion Mid Back or Approved equivalent with Adjustable Armrest, Seat Back Assembly : The cushioned seat base moulded in glass-filled Poly - amide. moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high strech knitted polyester fabric. Mid Back Size : 44.0cm W x 46.0cm H & Seat Size : 48.5 cm W x 47.0 cm D. High Resilience (HR) Polyurethane Foam : The HR polyurethane foam used in seat and back cushion in moulded in Density 45+2 kg/m3, and hardness load 16+2 kgf as per should be : 7888 for 25% compression. Tilt Mechanism, Spines & Spine connector : The seat and back shall be firmly connected to the base frame and shall be cantilevered in such a way that it gives a multi - dimensional movment possibillity just with a impact cushioning while sitting and synchronises with the back movement during posture changes. The \\"S\\" poly -amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which should be inbuilt in seat base and the tension (return force) should be user weight dependent. Fixed Armrest : The assembly should be having Fixed arm rest structure moulded in glass-filled Poly-amide. The Armrest Top should be made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. Pneumatic hight adjustment : The seating height can be adjusted with a pnenmatic gas-lift having an adjustment stroke of 9.2 + 0.3 cm.Pedestal Assembly : The pedestal should be injemoulded should be glass-filled Poly-amide and fitted with 5 nos. win wheel diameter and assembld to the pedestal. |
| 506 | Providing and placing in position Godrej make Spacio Plus Modular workstation for 1 person with Penta worksurface of size 1500W1 x1500W2 x 600D, with Common Front Panel & Common Side Panel Ht. - 1200.FabricMagnetic, White Board & Metal Tiles used with Raceway below worksurface including Pedestal, KBPT, CPU Trolly or Approved equivalent.: Modular tile based system with nominal thickness of 50mm. The trim width should be 56.5mm and the thickness of panel after fitting the tiles on frame should be 52 mm . Metal fascia for wire managment should be provided at the bottom skirting level as standard. The metal facia should be powder coated .Exposed vertical and top edges shall be covered by curved metal trims. Main Frame:Spacio Plus has Vertical upright made 1.5mm thick CRCA M.S Grade D formed into \\"C\\" Channel of 28.4 x 40.The Top horizontal should be a 1.2mm thick M.S tube 25.4 x 25.4 mm and bottom horizontal should be a 1.5mm thick M.S tube 38.1 x 25.4 mm (1 x 1.5 inch) .The frame should be powder coated in standard black color . Fabric Magnetic Tiles shall be 0.6mm thick GI Sheet Metal Tiles, which shall be Fabric upholstered. Plain metal tiles shall be powder coated metal tiles in 0.6mm thick M.S CRCA grade D as per IS.513-1994.White board shall be made up of 0.6mm decorative laminate on visible side and 0.6mm backing laminate on back side with 8mm MDF as substrate. Frame shall be fitted with flat Trims of 56.5mm x 10.5mm and average wall thickness of 1.0mm.These Trims shall be made from powder coated alluminium alloy extrustions. Worktop shall be made of 25mm thick Prelaminated particle board. All the edges of worksurface shall be provided with machine pressed 2mm thick PVC Edgeband glued with hotmelt EVA glue. The worksurface shall be mounted on the New 13\\" worksurface bracket of 2.0mm thick M.S.A corner bracket should be used to support the worksurface at the corner junction of the frames, side panel will be attached to the upright using the side panel brackets. The Side Panel should be made from 25mm thick PLT particle board (As per IS: 12823) and it should be edge banded all over with machine pressed 2mm thick PVC lipping glued with hotmelt EVA glue. The side panel should be fitted with angle bracket and side panel bracket along with M6 Glide Screw for height adjustment at the bottom. |
| 507 | Providing and placing in position Godrej make Spacio Plus Modular workstation for 2 person with Penta worksurface of size 1500W1 x1500W2 x 600D, with Common Front Panel & Common Side Panel Ht. - 1200.Fabric Magnetic, White Board & Metal Tiles used with Raceway below worksurface including Pedestal, KBPT, CPU Trolly or Approved equivalent.: Modular tile based system with nominal thickness of 50mm. The trim width should be 56.5mm and the thickness of panel after fitting the tiles on frame should be 52 mm . Metal fascia for wire managment should be provided at the bottom skirting level as standard. The metal facia should be powder coated .Exposed vertical and top edges shall be covered by curved metal trims. Main Frame:Spacio Plus has Vertical upright made 1.5mm thick CRCA M.S Grade D formed into \\"C\\" Channel of 28.4 x 40.The Top horizontal should be a 1.2mm thick M.S tube 25.4 x 25.4 mm and bottom horizontal should be a 1.5mm thick M.S tube 38.1 x 25.4 mm (1 x 1.5 inch) .The frame should be powder coated in standard black color . Fabric Magnetic Tiles shall be 0.6mm thick GI Sheet Metal Tiles, which shall be Fabric upholstered. Plain metal tiles shall be powder coated metal tiles in 0.6mm thick M.S CRCA grade D as per IS.513-1994.White board shall be made up of 0.6mm decorative laminate on visible side and 0.6mm backing laminate on back side with 8mm MDF as substrate. Frame shall be fitted with flat Trims of 56.5mm x 10.5mm and average wall thickness of 1.0mm.These Trims shall be made from powder coated alluminium alloy extrustions. Worktop shall be made of 25mm thick Prelaminated particle board. All the edges of worksurface shall be provided with machine pressed 2mm thick PVC Edgeband glued with hotmelt EVA glue. The worksurface shall be mounted on the New 13\\" worksurface bracket of 2.0mm thick M.S.A corner bracket should be used to support the worksurface at the corner junction of the frames, side panel will be attached to the upright using the side panel brackets. The Side Panel should be made from 25mm thick PLT particle board (As per IS: 12823) and it should be edge banded all over with machine pressed 2mm thick PVC lipping glued with hotmelt EVA glue. The side panel should be fitted with angle bracket and side panel bracket along with M6 Glide Screw for height adjustment at the bottom. |
| 508 | Providing and placing in position Godrej make Canteen Table, Model: Time-out 6 seater(size: 1734x1175x750 mm)or Approved equivalent: Cafeteia Table, PU painted 25mm Base material 25mm MDF board on top PU painting of minium 2H hardness with 75% gloss as per color chart, combination color graphices on the centre. Color as per color chart. Brown laminate on bottam. Specially profilled edge for comfort.Understructure : Bend pipe Uunderstructure of MS Power coated. Pipe dia 38mm, 2mm thk. Understructure fitted with top by SS machine screws.Legs : MS powder coated legs for PU top & SS legs for membrane top. 38 mm dia pipe legs shall be fixed with Understructure & table top. Glide : Plastic Glide fixed at the Understructure to prevent the damage of table top during stocking. |
| 509 | Providing and placing in position Godrej make Model:Unwind Chair café or Approved equivalent.: The seat and back shall be made of injection moulded high impact strength Poly Propylene polymer compound with indoor grade UV resistance (Refer colour chat in product catalogue)*SEAT SIZE : 52.5cm.(W), x 53.2 cm.(D)*BACK SIZE : 51.6cm.(W), x 40.5 cm. (H)2. S.S UNDERSTRUCTURE OPTION FOR CAFE CHAIR : The tubular welded frame should be made from Dia 2.22 + 0.03 cm. x 0.12 + 0.0128 cm and 3.5 + 0.03 cm x 1.5 +0.03 cm x0.12+ 0.0128 cm Stainless Steel 202 grade tube Tubes shall be buff polished to give shiny finish.3. SHOE : The shoes shall be made of high impact strength Poly Propylene polymer compound with indoor grade UV resistance and assembled over the tubular frame.4. |
| 510 | Storage-Compactors Providing & Placing Godrej Make -optimizer or Approved Equivalent or compactor storage Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513 . Each body Construction shall have a main unit plus add on units (1,2,3,4,5) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be made from CRCA steel 0.8 mm thick IS :513 .Uniformly distributed load capacity of 80 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3.15 mm thick conforming to IS : 10748 . Finish shall be epoxy polyester powder coat of approved color & shade with a dry film thickness of minimum 40 microns .The Movements shall be Drive Type configuration : In case of D2 & D3 movement of units is achieved mechanically through a PU Drive Wheel and Sprocket -Chain-Tensioner arrangement mounted rigidly onto body size .For D3 each movable undercarriage shall be provided with 2 rollers on the shaft for driving , 2 antifriction ball bearing for rolling and 4 antifriction ball bearing for guiding between rail . Fittings shall be centralized locking arrangement through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together . The Recess handle lock is of Godrej make & placed at suitable height . This arrangement occupies a space of 90.0 mm . When the last unit is twin movable , hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto drive unit cover ; and with tile fascia option , it will be mounted in the recess of vertical trim . Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units . Knob shall be rotated to unlock position when units are to be moved . End stoppers shall be provided to prevent derailment . Door locking shall be having hinged doors of recessed die cast handle cum lock giving 3 way locking through a lever & shooting bolts . Guide channels shall have 'J' section 2 mm thick HR & 25 mm Square bright bar . Easteners shall be galvanized/blackodized/Zn plated .The label holder shall be made from 2 mm thick clear transparent acrylic sheet. Fascia(tiling) 3 tile pattern fascia option on drive side panel plus 3 tile pattern fascia on non-drive side panel plus 3 tile pattern fascia option on back panel ofp p p p p p p p single last plus 3 tile pattern fascia option on back panel of single static . The tiles are held together by stiffeners & fasteners in 2 vertical metal trims. |
| 511 | TwinMobileDrivecoverunit3Bay -2745mm(W)x915mm(D)x2080mm(H). total no. of loading levels per understructure shall be 30 |
| 512 | Providing and placing in position Godrej make Conference Room Table, Model: Senate 31 or Approved equivalent. Top thickness 37.6 (18mm + 18mm + 0.6 mm DL + 0.4mm (Membrane) Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom. Understructure Legs Modesty Panel Made from 36mm PPB (18+18) having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg should be 37.2mm. Made from PLT (Prelaminated Twin) boards of 18mm thick. Wire Manager Wire Carrier Carrier Cover Made from 0.6mm thick CRCA painted. Made of 12mm thk. MDF Painted all over. Material Substrate MDF Skin PVC Membrane foil (0.4mm thk) clad on the substrate MDF using PU glue for better adhesion. This foil should be pre-coated with layer of polyurethane for better scratch resistance. |
| 513 | Providing and placing in position Godrej make First Impression 3-Arch Reception Table Rubber wood top or Approved equivalent. Clean Matt PU finished 18 mm thick. Inside radius 700 mm. Outside radius 1350 mm. Depth 650 mm. Cork : Rubberized cork 18 m thick. Glass : Frosted glass 10 mm thick diamond cut finished on edges. Inside Radius 1202.5 mm . Depth : 200 mm. Note : Angle sustained within Arc Surface is 60 Deg. MS perforated sheet below work surface: 0.8 mm thk x 665.00 mm (H) x 1345 mm (flat length). Above work surface : 0.8 mm thk x 260 mm (H) x 1345 (flat length)Legs: MS tube 1.6 mm thick, dia 50.8 mm, height # 604 mm. Note : Allover all dimensions are in mm and are subject to change. 2800 x 1430 x 725 (work surface) mm (LxBxH) |
| 514 | Providing and placing in position Godrej make Talk 6-Str(Boat Convex) Conference Table Table or Approved equivalent with dimension 2100W x 1200D x 750H. The top should be made of 25mm thick +/- 1.5mm (25mm + 12 mm MDF OSR as per should be 12406 + 0.4 mm Membrane Foil); Under structure made of Legs of Nickel chrome plated made from 50.8x1.6 mm Thk MS ERW Tube. With Laminated Modesty Panel made from 18 mm thk PLT as per should be # 12823 or 16 mm Plain Particle Board + 0.6 mm Top laminate on either side (Postlam) and PVC edge banding on all the sides. Work Surface and Modesty shall be assembled together with Powder Coated (DFT 40-60 Microns) Modesty bracket made from 2 mm thick CR steel (IS:513).Should have Access Flap & Switch Mounting Tray made of Matt silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical/Data/Voice Sockets access from top. Powder Coated (DFT 40-60 Micron) switch mounting tray made from 0.8/1.2mm CR Steel IS: 513. |
| 515 | Providing and fixing glass shelves (upto 500 mm wide) made out of 12mm thick clear toughened glass, size as per drawing, all edges to be machine polished, all edges shall be beveled/chamfered including approved fixing arrangement like stainless steel clamps to be 316 grade or patch fittings as directed, providing holes for SS bolts / clamps, all complete as shown in the drawings and as directed by EIC. The joints shall be sealed with transparent type silicon sealants. The shelves shall be fixed over wooden wall partitions / marble cladding etc. |
| 516 | PART-O: PASSENGER ELEVATOR |
| 517 | Supply, Installation, Testing & Commissioning of Electric Traction Type fully automatic gearless and machine room less Passenger Elevator having SS Moon Rock Finish Enclosure with AC Variable Voltage & Variable Frequency drive unit suitable for operation on 415V +/- 10% , 3 Phase, 50 Hz. AC supply, power operated SS Moon Rock Finish center bi-parting opening type car & landing doors, electro-magnetic brake system, car operating panel with luminous buttons, overload warning indicator, battery operated alarm bell, emergency light and alarm button, intercom suitable for hook up to EPABX, Brail Button & SS Rail on rear side, infrared ray sensing door protection for full height & mechanical safety by pressure sensor, reverse phase relay on controller, fire man's switch at ground floor, digital car positions indicator in car & at all floors with up / down direction indications, light fixtures, ventilation fan, landing sill, main beam in shaft for machine, pit ladder, complete with all accessories serving different floors in the elevator shaft alongwith Automatic Rescue Device NO. OF ELEVATOR-1 (ONE ) NO. TYPE-MRL PASSENGER CAPACITY-6 PASSENGER / 408 KGS.. TRAVEL-GROUND TO 3RD FLOOR. STOPS & OPENINGS-4 STOPS AND 4 OPENINGS. FLOORS SERVED-G ROUND, 1ST, AND & 3RD FLOOR. OPERATION-1.DIGITAL CAR POSITION INDICATOR AT ALL FLOOR & DIGITAL FLOOR POSITION INDICATOR AT ALL LANDINGS.2.DELUXE PUSH BUTTON CONTROL WITH PROVISION FOR ELEVATOR ATTENDANT. SIGNALS-MICROPROCESSOR BASED CONTROLLER WITH ALL MODERN FACILITIES. “UP” & “DOWN” INDICATION AT ALL LANDINGS, LIGHT & ALARM. MACHINE POSITION HOISTWAY-LOCATED DIRECTLY ABOVE THE LIFT SHAFT( MRL).. HOISTWAY AVAILABLE-1500 MM WIDTH X 1650 MM DEPTH CAR ENCLOSURE-EXCELLENT STAINLESS STEEL CABIN REDUCTION GEAR-TRACTION TYPE. MOTOR-3 PHASE LIFT DUTY MOTOR . INSTALLATION-INDOOR CAR ENTERANCE-PROTECTED BY POWER OPERATED STAINLESS STEEL AUTOMATIC DOOR. LANDING ENTERANCE-PROTECTED BY POWER OPERATED STAINLESS STEEL AUTOMATIC DOOR. CAR VENTILATION WIRE ROPE WIRE ROPE-LIFT DUTY 8/19 SEALE. MAKE: USHA MARTIN or EQUVALENT. DOOR OPERATION-AUTOMATIC POWER SUPPLY REQUIRED-i) 415 VOLTS, TP&N, 59 Hz. A.C.ii) 230 VOLTS, SP&N, 50 Hz. A.C |
| 518 | PART-P: MISCELLANEOUS |
| 519 | Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material outside premises at an unobjectionable place as / direction of Engg-in-charge |
| 520 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: |
| 521 | Of area 3 sq. metres and below. |
| 522 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead: |
| 523 | For thickness of tiles 10 mm to 25 mm. |
| 524 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 525 | Structural steel work riveted,bolted or welded in built up sections, trusses & framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: |
| 526 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, within premises and lift upto 1.5m |
| 527 | Extra for every additional lift of 1.5m or part thereof in excavation or banking excavated or stacked materials in all kinds of soil |
| 528 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 529 | iv) Lintels, beams plinth beams,girders bressumers and cantilevers |
| 530 | vi) Stairs, (excluding landings) except spiral-staircases |
| 531 | Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work using cement content as per approved design mix manufactured in fully automatic batching plant & transported to site of work in transit mixer for all leads having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing & reinforcement including cost of admixtures in recommended proportions as per IS:9109 to accelerate/ retard setting of concrete, improve workability without impairing strength & durability as per direction of Engineer-in-charge (Note :- Cement content considered in this item is @ 330 kg/cum. Less cement used as per design mix (if any) will be recoverable separately. No extra payment against extra cement if used shall be payable. |
| 532 | i) M25 RMC for All works UP TO PLINTH LEVEL |
| 533 | i) 6mm thick plaster of mix 1:3 (1 cement: 3 fine sand) |
| 534 | ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786 |
| 535 | Providing and laying dry brick on edge flooring in required pattern with bricks of Class designation 7.5 on a bed of 12 mm mud mortar including filling joints with river sand with common burnt clay non- modular bricks |
| 536 | Taking out existing CC interlocking paver blocks from footpath central verge, including removal of rubbish etc., disposal of unserviceable material out of site at unobjectionable place and stacking serviceable material within premises as per direction of Engineer - in-Charge |
| 537 | iv) Brick work in Cement mortar 1:6 (1 cement: 6 coarse sand) in superstructure in all shapes & sizes in superstructure ABOVE PLINTH & UP TO FLOOR V LEVEL |
| 538 | Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduces steel bars for sunshades/ balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-in-charge: Upto and including 12mm dia. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
| 8 | Click here to download tender document | Tender Documents |
| 9 | Click here to download tender document | Tender Documents |
| 10 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
