|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m, as directed by engineer-in-charge. The Contractor has defect different utilities like sewer line, water supply line, electric cable, telephone cable , gas pipe line etc, using utility decteting machine before start of excavation and shall start excavation only after getting permission of Engineer-in-charge. |
| 2 | preparation and consolidation of sub grade with power road roller of 8to 12 tonne capacity after excavating after excavating earth to an averge of 22.5cm depth , dressing to camber and consoildating with road roller including making good the undulations etc . and re- roiling the sab grede and disposal of surplus earth with lead upto 50 metres.(16.1) |
| 3 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibrator roller to achieve the desired density, complete as per clause 401. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level. |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 9 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved. |
| 10 | Providing and laying factory made coloured chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern. finising and sweeping extra sand. Complete all as per direction of Engineer-in- Charge 16.91.2, 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 100 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 13 | 12mm cement plaster of mix : 1:4 (cement :4 coarse sand) (13.4.1) |
| 14 | Neat cement punning(13.18) |
| 15 | Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. |
| 16 | Providing and laying C.C. parement of mix M 25with ready mixed concrete from batching plant .the ready mixed concrete shall be laid and finished with screed board vibrator vacuum dewatering process and finally finished , vacuum dewatering procees and finally finished by floating brooming with wire brush etc. complete as per specifications and directions of engineer-in-charge ( the panel shuttering work shall work shaal be paid for separately (note:- cement content considered in this item is @ 330 kg/cum.Excees/less cement used as per design mix is payable /recoverable saperately. ready desige mix is payable / recoverblre seperateiy). |
| 17 | Painting with synthetic enemal paint of approved brand and manufaceture togive and even shade :two or more coats on new work over and under coat of suitable shede with ordinary paint of approved brand and manufacture. |
| 18 | P/F plain - non asbestos cement sheet strip in joints pavements /terrazo floooring 100mm wide and 6mm thick (based on item no 11.13.0/p-639 /dar -2016 vol-1) |
| 19 | Dismantling karb stone (dismantling karb stone by manual means and disposal of dismantled material with all lifts. And up to lead of 1000 metre) |
| 20 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Please Enable Macros to View BoQ information |
