|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. |
| 2 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 3 | providing and laying flat brick soling layer on prepared subgrade according to lines grades and cross-section shown on the drawing filling joints with earth free from clay with plasticity Index not exceeding 6 watering and rooling the same with three wheeled road roller 80-100 kN as per Mord Technical Specification Clause 412. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering shuttering - All work upto plinth level 1:3:6(1 cement:3fine sand:6 graded well burnt brick aggregate 20 mm nominal size.) |
| 5 | First class brick work in foundation and plinth including cost of all metarial as required complete In cement mortar 1:4(1cement:4 fine sand) |
| 6 | Half brick masonry work with first class brick work in foundation and plinth including cost of all metarial as required complete In cement mortar 1:4(1cement:4 fine sand) |
| 7 | Supply & installation of pre-painted Galvalume sheets for roofing / cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches whiletransportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 0.50mm thickness. |
| 8 | Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 9 | Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., includingcutting, hoisting, fixing in position and applying apriming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 10 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm: 0.50mm thickness |
| 11 | Providing and laying in position specified grade ofreinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All work upto plinth level:1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stoneaggregate 20 mm nominal size) |
| 12 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding allcomplete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D ormore |
| 13 | 12 mm cement plaster of mix in cement mortar 1:4(1 cement : 4 fine sand) |
| 14 | Neat Cement punning |
| 15 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as permanufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 16 | Installation and fitting fixing of the open Gym equipments of follows as per market rateTreadmill |
| 17 | Installation and fitting fixing of the open Gym equipments of follows as per market rate cross trainer |
| 18 | Installation and fitting fixing of the open Gym equipments of follows as per market rate spin bike |
| 19 | Installation and fitting fixing of the open Gym equipments of follows as per market rate Multi functional trainer with smith machine |
| 20 | installation and fitting fixing of the open Gym equipments of follows as per market rate Leg press |
| 21 | installation and fitting fixing of the open Gym equipments of follows as per market rate pee deek fly |
| 22 | installation and fitting fixing of the open Gym equipments of follows as per market rate Leg pull down and row |
| 23 | installation and fitting fixing of the open Gym equipments of follows as per market rate leg ext and curi |
| 24 | installation and fitting fixing of the open Gym equipments of follows as per market rate Olympic 3 in bench |
| 25 | installation and fitting fixing of the open Gym equipments of follows as per market rate adjustable bench |
| 26 | installation and fitting fixing of the open Gym equipments of follows as per market rate flat simple bench |
| 27 | installation and fitting fixing of the open Gym equipments of follows as per market rate preacher curi bench |
| 28 | installation and fitting fixing of the open Gym equipments of follows as per market rate dumbbell rack |
| 29 | installation and fitting fixing of the open Gym equipments of follows as per market rate vertical kee raise halt |
| 30 | installation and fitting fixing of the open Gym equipments of follows as per market rate Dumbbell |
| 31 | installation and fitting fixing of the open Gym equipments of follows as per market rate plates |
| 32 | installation and fitting fixing of the open Gym equipments of follows as per market rate rod set |
| 33 | installation and fitting fixing of the open Gym equipments of follows as per market rate 32mm/25mm thick GYM floor mat |
| 34 | installation and fitting fixing of the open Gym equipments of follows as per market rate Yoga mat |
| 35 | installation and fitting fixing of the open Gym equipments of follows as per market rate Twister (two-in-one) |
| 36 | installation and fitting fixing of the open Gym equipments of follows as per market rate Mirror |
| 37 | Installation and fitting fixing of the open Gym equipments of follows as per market rate Installation Please Enable Macros to View BoQ information |
