|
| 1 | Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. |
| 2 | Supplying and fixing metal box of 100mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 2 no. 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required. |
| 3 | Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required. |
| 4 | Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18\\" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required:- |
| 5 | 25 Liter capacity water heater (Cat-A) |
| 6 | 10Liter capacity water heater (Cat-A) |
| 7 | Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- |
| 8 | Exhaust Fan, Heavy duty, (Domestic) 300 mm sweep |
| 9 | Exhaust Fan, Light duty, (Domestic) 250 mm sweep |
| 10 | Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit a as required. |
| 11 | 2x1.5 Sq. mm. +1 X 1..5sq mm earth wire |
| 12 | 2x4 sq mm+4 X 4 sq mm earth wire |
| 13 | 4x4 sq mm+2 X .4 sq mm earth wire |
| 14 | 2x6 sq mm+1 X 16 sq mm earth wire |
| 15 | S/E of LED Panel with PDC body and polycarbonate /Acrylic diffuser to be mounted in recess The job includes carriage, erection, making connections testing and commissioning of the fittings.2 * 2 feet |
| 16 | Specification of LED fittings: |
| 17 | Wattage of LED fittings - As per following parameter. |
| 18 | Total lumens of the fittings - as per wattage |
| 19 | Diffuser - polycarbonate/acyrlic diffuser UGR <30 |
| 20 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 21 | Input frequency - 50 Hz + 1 Hz |
| 22 | Power factor - Minimum 0.90 |
| 23 | Luminaire efficacy - ≥110 lm/w |
| 24 | Color rendering index - CRI shall be greater than 80 |
| 25 | Working/ operating temperature - 00 to + 450c or better |
| 26 | Color temperature - 60000K + 10% |
| 27 | Electronic Driver |
| 28 | Drive current (LED) - As per OEM. |
| 29 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 30 | Type of driver - Constant current output driver |
| 31 | THD - Less than 10% |
| 32 | Surge Protection - 2.5 KV minimum |
| 33 | Efficiency Driver - ≥85% |
| 34 | Protection - Shall have under voltage and over voltage protection. |
| 35 | Guarantee of LED fittings including LED driver - 2 years against manufacturing defect. |
| 36 | Fixture - Should comply with LM 79 test from UL/NABL lab. |
| 37 | LED Type/ Make/ Model - Power CREE/ OSRAM/ NICHIA/ Philips LUMILED with life more than 50,000 burning hours @70% lumen maintenance complying with LM 80 test report from the manufacturer. |
| 38 | Life of LED - 50000 burning hours at 70% lumen maintenance |
| 39 | Lumen output of the fitting |
| 40 | LED Panel Light 2'x2' ≥3300Lumens. |
| 41 | S/E of LED Batten with polycarboante body and diffuser The fitting should be installed on existing surface/recess The job includes carriage, erection, making connections testing and commissioning of the fittings. |
| 42 | Specification of LED fittings: |
| 43 | Wattage of LED fittings - As per following parameter. |
| 44 | Total lumens of the fittings - as per wattage |
| 45 | Diffuser - Polycarbonate diffuser/PMMA |
| 46 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 47 | Input frequency - 50 Hz + 1 Hz |
| 48 | Power factor - Minimum 0.90 |
| 49 | Luminaire efficacy - ≥100 lm/w |
| 50 | Color rendering index - CRI shall be greater than 80 |
| 51 | Working/ operating temperature - 00 to + 450c or better |
| 52 | Color temperature - 60000K + 10% |
| 53 | Electronic Driver |
| 54 | Drive current (LED) - As per OEM. |
| 55 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 56 | Type of driver - Constant current output driver |
| 57 | THD - Less than 10% |
| 58 | Surge Protection - 2.5 KV minimum |
| 59 | Efficiency Driver - ≥85% |
| 60 | Protection - Shall have under voltage and over voltage protection. |
| 61 | Guarantee of LED fittings including LED driver - 2 years against manufacturing defect. |
| 62 | Fixture - Should comply with LM 79 test from UL/NABL lab. |
| 63 | LED Type/ Make/ Model - Power CREE/ OSRAM/ NICHIA/ Philips LUMILED with life more than 25,000 burning hours @70% lumen maintenance complying with LM 80 test report from the manufacturer. |
| 64 | Life of LED - 25000 burning hours at 70% lumen maintenance |
| 65 | Lumen output of the fitting |
| 66 | LED Batten Light ≥2000Lumens. |
| 67 | S/E of LED Downlighter round type surface with CRCA / PDC body and diffuser. The fitting should be installed on existing surface. The job including carriage, erection, making connections testing and commissioning of the fittings. |
| 68 | Wattage of LED fittings - As per following parameter. |
| 69 | Total lumens of the fittings - as per wattage |
| 70 | Diffuser - polycarbonate/acyrlic diffuser UGR <30 |
| 71 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 72 | Input frequency - 50 Hz + 1 Hz |
| 73 | Power factor - Minimum 0.90 |
| 74 | Luminaire efficacy - ≥110 lm/w |
| 75 | Color rendering index - CRI shall be greater than 80 |
| 76 | Working/ operating temperature - 00 to + 450c or better |
| 77 | Color temperature - 60000K + 10% |
| 78 | Electronic Driver |
| 79 | Drive current (LED) - As per OEM. |
| 80 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 81 | Type of driver - Constant current output driver |
| 82 | THD - Less than 10% |
| 83 | Surge Protection - 2.5 KV minimum |
| 84 | Efficiency Driver - ≥85% |
| 85 | Protection - Shall have under voltage and over voltage protection. |
| 86 | Guarantee of LED fittings including LED driver - 2 years against manufacturing defect. |
| 87 | Fixture - Should comply with LM 79 test from UL/NABL lab. |
| 88 | LED Type/ Make/ Model - Power CREE/ OSRAM/ NICHIA/ Philips LUMILED with life more than 50,000 burning hours @70% lumen maintenance complying with LM 80 test report from the manufacturer. |
| 89 | Life of LED - 50000 burning hours at 70% lumen maintenance |
| 90 | Lumen output of the fitting |
| 91 | LED Panel Light ≥2400Lumens. |
| 92 | Supplying and fixing following rating piano type switch/ Socket on the existing switch box/cover including connection ect. As required;- |
| 93 | S.P.5/6 Amps One way Piano switch |
| 94 | 3 pin 5/6 Amp Socket Out let piano type. |
| 95 | S.P.15/16 Amps One way switch |
| 96 | 6 pin 15/16 A socket outlet |
| 97 | Supplying and fixing following rating modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 98 | 5/6 Amps switch |
| 99 | 15/16 A switch |
| 100 | 3 pin 5/6 A socket outlet |
| 101 | 6 pin 15/16 socket outlet |
| 102 | Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- |
| 103 | Double pole. Cat-A. |
| 104 | Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- |
| 105 | Double door-8 way |
| 106 | Double door6way |
| 107 | Supplying and fixing PVC batten / angle holder including connections etc. as required. |
| 108 | Supplying and fixing of Ding Dong /electronic/musical bell suitable for ac/dc single phase 230 v complete as required bakelite batton/angle holder including connection ect. as required |
| 109 | Providing and fixing geyser element ( cup type, triangular, typical triangular) complete with all accessories connections, testing and commissioning etc. as required. |
| 110 | Providing and fixing geyser thermostate for different type of geyser complete with all accessories connections, testing and commissioning etc. as required. |
| 111 | S/E of LED Downlighter (recess) round type with CRCA / PDC body and diffuser. The fitting should be installed on existing surface / recess. The job including carriage, erection, making connections testing and commissioning of the fittings. |
| 112 | Wattage of LED fittings - As per following parameter. |
| 113 | Total lumens of the fittings - as per wattage |
| 114 | Diffuser - polycarbonate/PMMA |
| 115 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 116 | Input frequency - 50 Hz + 1 Hz |
| 117 | Power factor - Minimum 0.90 |
| 118 | Luminaire efficacy - ≥110 lm/w |
| 119 | Color rendering index - CRI shall be greater than 80 |
| 120 | Working/ operating temperature - 00 to + 450c or better |
| 121 | Color temperature - 60000K + 10% |
| 122 | Electronic Driver |
| 123 | Drive current (LED) - As per OEM. |
| 124 | Operating voltage - 140 V to 270 V, AC supply or better. |
| 125 | Type of driver - Constant current output driver |
| 126 | THD - Less than 10% |
| 127 | Surge Protection - 2.5 KV minimum |
| 128 | Efficiency Driver - ≥85% |
| 129 | Protection - Shall have under voltage and over voltage protection. |
| 130 | Guarantee of LED fittings including LED driver - 2 years against manufacturing defect. |
| 131 | Fixture - Should comply with LM 79 test from UL/NABL lab. |
| 132 | LED Type/ Make/ Model - Power CREE/ OSRAM/ NICHIA/ Philips LUMILED with life more than 50,000 burning hours @70% lumen maintenance complying with LM 80 test report from the manufacturer. |
| 133 | Life of LED - 50000 burning hours at 70% lumen maintenance |
| 134 | Lumen output of the fitting |
| 135 | LED Panel Light ≥2400Lumens. Please Enable Macros to View BoQ information |
