|
| 1 | COMMON SCHEDULE OF RATES(34.37) DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES (34.37 A) Supply and erection of Double Walled Corrugated(DWC) HDPE pipe to be laid 1mtr. below ground levelincluding excavation placing the pipe in position and backfilling with excavated soil etc of the required size Double Walled Corrugated HDPE Pipe 50/38mm (Outer/ Inner dia.) |
| 2 | XLPE INSULATED LT CABLES: (34.10 D) XLPE INSULATED UN-ARMOURED CABLES(LOOSE): Supply, laying and erection of aluminium conductor XLPEinsulated PVC sheathed Un-armoured and servedcable 1100 volts grade as per IS 7098 (Part-1)1988 to belaid loose in the existing trench or pipe as per PWDGeneral Specifications:- Overall size 16sq.mm (4Core) Un-armoured (Loose) |
| 3 | GALVANIZED STEEL OCTAGONAL POLES FORWIND VELOCITY OF 169 Km/HOUR: Supply and erection ofGalvanized Steel Octagonal Pole (Sheet thickness 3mm)designed to withstand wind speed 169km/ hour of suitablelength (Raw material confiming to IS-5986(FE-510), BSEN-10025S-355J or ASTM-572A (GR-50)) andthickness of galvanization (70mm thick) conforming toIS:2629/ IS:2633/ IS:4759, BSEN-ISO-1461-1991 ORASTM-A123/A123M-02. The pole shall be in single piecehot dip galvanized and shall be tapered towards the top.The bottom section shall have openable slot with exteriorsurface door & shall have suitable locking arrangementfor housing three phase 4wire cable connection, bakelitesheet, MCB, loop in and out arrangement for incoming/outgoing cables. There shall be suitable arrangement forearthing. Rigid Base plate of suitable size and thicknessshall be welded inside and outside at the bottom of polewith provision for fixing 4 foundation bolts. Theoctagonal pole shall be bolted on a pre- cast foundation witha set of four foundation bolts for greater rigidity. Thefoundation shall be erected over cement concrete M20with steel of given size as per design of original polemanufacturer to fixed up to a required planting depth belowground level as required:Galvanized Octagonal Pole Overall Length 7 metre (Sheet thickness 3mm), Top dia.(A/F) 70mm and bottom dia. (A/F) 130mm, Foundation size below G/L 550mm x550mm x 1400mm, 4Nos. Foundation Bolts size 20mmdia., Length=700mm with Base Plate Dimensions240mm x 240mm x 16mm Thick |
| 4 | SINGLE/ DOUBLE ARMBRACKETS:Supply and erection of bracket for galvanized octagonal pole,the bracket should be fixed on the top of the pole having topouter dia. 70mm to 90mm (A/F) complete in all respect as approved by theEngineer-in-charge at site:- Single arm bracket 1.5 metre long for galvanized octagonal pole |
| 5 | Double arm bracket 1.5 metre long for galvanized octagonal pole |
| 6 | PVC INSULATED FR COPPER CONDUCTORCABLES: Supply and erection of PVC insulated FR single core Unsheathed copper conductorcable (ISI marked) suitable upto 1100 volts grade confirmto IS:694/1990 left bare in pipe or casing of suitable sizecomplete in all respect as desired by theEngineer-in-charge:- Overall size 1.5sq.mm (Un-sheathed) |
| 7 | SHEET METAL CUBICAL PEDESTAL, TOWERSTRUCTURES, HT & LT LINE ITEMS, MS CHANNELS, BRASSGLANDS, ALUMINIUM & COPPER THIMBLES: Supply and erection of Sheet metal cubical pedestal madefrom 50mmx50mmx6mm thick MS angle iron frame with5 sides welded & covered with MS sheet 2mm thick & frontside hinged with 4\\" hinges & locking system with single/double door openable placed on MS strip of size 12.5mm x2.5mm thick welded with MS sheet, 4Nos. legs of50mmx50mmx6mm thick MS angle iron each of 600mmlong with MS sheet 100mmx100mmx6mm thickat the bottom end of the legs.Front door welded x-sectionally with MS flat25mmx5mm. The front side with MS sheet each 75mmwide & a bend of 75mm width outwards & inwards on allsides with tappered top 200mm high and pedesta with 4 Nos. supportingmembers each of MS flat 50mmx6mm thick accordingto cubical size duly welded & complete pedestal to bepainted with 1 coat of red oxide & 2 coats of paint &bonding to the existing earth. The Pedestal platform should be filled with 1:2:4 cementconcrete mixture and erected 150mm high from the top ofthe cement concrete platform. The job is to be completed asapproved by Engineer-in-charge:- Cubical Size 900mm high, 600mm wide and350mm deep with platform dimensions 700mm x 450mm x 450mm |
| 8 | S/E of Microprocessor Based Street Light Controllerwith digital time switch daily programmed with stand bylithium battery with back up of 6 years with min. timebetween 2 switching operations is 1 minute, threepole power contactors 40A. with coil voltage 220-230V ACwith 1 no. aux. contact NO, MCB 2 pole 40amp. (C-Curve,10kA) & power wiring with single core PVC insulated FRcable 10 sq. mm and control wiring with PVC insulated FRcable 1 sq. mm, 1 no. two position selector switch tobypass timer and other accessories & petty material(din rail, 4 pole bakelite terminal strip 63A/ 440V AC,required nut bolts) should be fixed on bakelite sheet 6mmthick to be mounted in a IP54 surface/ flush mountingpowder coated sheet metal (1.60mm thick) cabinethaving size 450mm x 600mm x 150mm to switch ‘ON’ allthe 3 phases & switch ‘OFF’ 3 phases pre-fixed timings complete in all respect as persatisfaction of Engineer-in-charge Street Light Controlle (For Three Single PhaseCircuits) with 3 Nos. Three Pole Power Contactors 40A, 1no. aux. contactor 6 amp. (2NO+2NC) with coil voltage220V AC, 3 Nos. MCB 2 Pole 40amp. (C-Curve,10kA) &petty material (Din rail, 2 Nos. 4 pole bakelite terminal strip63A/ 440V AC, required nut bolts) |
| 9 | GALVANIZED IRON PIPES AND G.I. EARTHINGSupply & erection of G.I. pipe (A-Class) as per IS:1239(Part-I) 2004 including sockets, bends, inspectionboxes, Steel hooks, GI saddle clamps and other pettymaterials etc., where necessary including paintingas per PWD General Specifications: Earthing earth rod 20mm dia for providing earth connections upto line earthwith G.I. Wire 8 S.W.G. (4mm dia.). The rod shall be taperedat one end and flatted on other end. The hole size10mm dia shall be drilled on the flatened side forfacilitating connection with G.I. wire and thimble etc. Therod shall be erected in ground upto complete lengthvertically GI Earth rod 20 mm dia., 3 mtr. Long |
| 10 | Supply and Erection of LED Street Light 70 watt (including LED driver) with pressure diecast aluminium housing with control gear ( with IP 65/ IP66 protection), CRI Minimum 70, CCT >5700K, toughenedglass fitting, LED fixture minimum 120 lumens perwatt and operating voltage between 140 to 270 volt, THD <10% ingress protection (as per BIS standards) , surgeprotection 10kv and above (as per (IS/IEC standards)wattage of each LED High power LED of 1 watt to 5 wattwith mandatory modular lenses, input AC frequency 50Hz ± 3 % 5 year warranty including their driverscomplete along with erection of the same with connections,testing etc. complete in all respects as approved anddesired by the Engineer-in-charge at site.LEDFitting as per Specifications approved by Hon. Tech.Advisor to CM Punjab vide Letter no AT-2021/GL1410-1422 Dated 06/05/2021. Dated06/05/2021. Besides this the lighting fixture manufacturesshould have in house NABL accredited labortary. Make -Havells ENDURASUNDOWNSL70WLED757PASYBOPC / Crompton LSTS-70-CDL-M / SURYA SLEUL 70W IP66 NGN / Bajaj ENXTP 84L WH CR PC SD Please Enable Macros to View BoQ information |
