|
| 1 | Jungle Clearance |
| 2 | Excavation by mechanical means(JCB or Hydraulic excavator) intrenches for pipe lines with straight or open cutting in streets or openarea including trimming anddressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering, including thecost of dewatering of rainwater,diversionfor traffic, night signals. providing & fixing caution boards, crossingover trenches foraccess to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving leadupto15metercompletein all respect.a) Earth work upto 1.5 m. Depth for a)All classes of soil except rocky |
| 3 | Excavation by mechanical means(JCB or Hydraulic excavator) intrenches for pipelines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling, consolidation,watering, including thecost of dewateringof rainwater,diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches foraccess to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto15meter complete in all respect.a)Exceeding 1.5m depth but not exceeding 2.25 m depth. Depth for a)All classes of soil except rocky |
| 4 | Excavation by mechanical means(JCB or Hydraulicexcavator) intrenchesforpipelines with straight or open cutting in streets or openarea including trimming anddressing sides levellingof bedsof trenches tocorrect grade, cutting joint holes, refilling consolidation,watering, including thecost of dewateringof rainwater,diversionfor traffic, night signals. providing & fixing caution boards, crossingover trenches foraccess to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the towninvolvingleadupto15metercompletein all respect.a)Exceeding 2.25 m depth upto 3.00 m depth. Depth for a)All classes of soil except rocky |
| 5 | Earthwork in excavation in foundations trenches etc. inall kinds of soil wherePick-Jumperworkis not involvedand not exceeding 2.0metresdepth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling aroundmasonryin15cm, layerswithcompaction including disposal of all surplussoil asdirected within lead of 30 metres. |
| 6 | Cement Concrete 1:4:8 with (i) stone ballast 20mm gauge (PCC) mixing by mechanical means using concrete mixer volumetric type. |
| 7 | Cement concrete 1:2:4 With stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type |
| 8 | Providing and filling sand grading as perspecifications or fine grade around thevarious sizes of G.I. pipes in external work |
| 9 | Reinforced cement concrete M-25 mechanically batchmixed using batch type concretemixer asper IS:1791andvibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 10 | First class burnt brick work laid in cement sandmortar 1:4 in foundation and plinth |
| 11 | 12.5 mm thick cement plaster 1:4 |
| 12 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 13 | Centering and shuttering for columns (circular or curved in plan) |
| 14 | Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. |
| 15 | Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in postion complete. |
| 16 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (400 mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge).B) Class PN-1.6 as per ISI |
| 17 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (350mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge).B) Class PN-1.6 as per ISI |
| 18 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (300mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge). B) Class PN-1.6 as per ISI |
| 19 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (200mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge).B) Class PN-1.6 as per ISI |
| 20 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (150mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge). B) Class PN-1.6 as per ISI |
| 21 | Providing, laying, fixing, testing and commissioning of 'C' Class heavyduty MS Pipe conforming to Indian Standard IS :1239/3589 includingfittings like tees, bends,sockets, elbows, flanges, tapers, nutsbolts, gaskets etc. in ground with anti corrosive treatment with wrapping coating tape (4mmpypkotetape)asperIS:10221includingcost of primer etc. excluding cost of excavation and refilling complete in all resepcts i/d 400 mm,thickness 6.3 mm |
| 22 | Providing, laying, fixing, testing and commissioning of 'C' Class heavyduty MS Pipe conforming to Indian Standard IS :1239/3589 includingfittings like tees, bends,sockets, elbows, flanges, tapers, nutsbolts, gaskets etc. in ground with anti corrosive treatment with wrapping coating tape (4mmpypkotetape)asperIS:10221including cost of primer etc. excluding cost of excavation and refilling complete in all resepcts i/d 300 mm,thickness 8 mm |
| 23 | Providing, laying, fixing, testing and commissioning of 'C' Class heavyduty MS Pipe conforming to Indian Standard IS :1239/3589 includingfittings like tees, bends,sockets, elbows, flanges, tapers, nutsbolts, gaskets etc. in ground with anti corrosive treatment with wrappingcoating tape (4mmpypkotetape)asperIS:10221includingcost of primer etc. excluding cost of excavation and refilling complete in all resepcts i/d 200 mm,thickness 6.3 mm |
| 24 | Providing, laying, fixing, testing and commissioning of 'C' Class heavyduty MS Pipe conforming to Indian Standard IS :1239/3589 includingfittings like tees, bends,sockets, elbows, flanges, tapers, nutsbolts, gaskets etc. in ground with anti corrosive treatment with wrapping coating tape (4mm pypkotetape)asperIS:10221including cost of primer etc. excluding cost of excavation and refilling complete in all resepcts i/d 150 mm,thickness 6.3 mm |
| 25 | Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS458-2003 into trenches for all depths and layingout the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigidmanner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed.The pipes shall rest on thebeds atall joints through their length sand fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc. R.C.C. Pipe NP -2 (29.46 b ) 450mm |
| 26 | Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigidmanner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed.The pipes shall rest on the beds at all joints through their length sand fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc. R.C.C. Pipe NP -2 (29.46 b ) 400mm |
| 27 | Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber jointandcuttingof reinforcedcement concrete spigot and socketed pipes and specialswithrubber ring ISImarekdasper IS code IS458-2003 into trenches for all depths and layingout the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigidmanner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed.The pipes shall rest on the beds at all joints through their lengths and fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc. R.C.C. Pipe NP -2 (29.46 b ) 300mm |
| 28 | Providing & fixing double air valve ISI Marked as per IS-14845 including jointing all carriages complete .C.I Double air valve (Size 100mm) |
| 29 | Nuts & Bolts of all sizes and length required |
| 30 | Providing & Fixiing C.I indicating plates of size 100mm x 100 mm for SV/FH including synthetic enammel paint & letters in whiteenamel paint, fixing in the ground with angle iron of size 25x25x5mm, 230mm height from ground including conrete block complete in all respect as directed by Engineer-in-charge |
| 31 | Laying of P.V.C. Pipesasper ISI-4985 (ISImarkedwith the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches tocorrectalignmentandgradients, cutting, jointingand testingcompleteasper specifications 400mm o/d PVC pipe of 4 Kgf. / sqcm (including length of riser 1.25 m) 07 no. Risers |
| 32 | Laying of P.V.C. Pipesasper ISI-4985 (ISImarkedwith the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches tocorrectalignmentandgradients, cutting, jointingand testingcompleteasper specifications 355mm o/d PVC pipe of 4 Kgf. / sqcm (including length of riser 1.25 m) 02 no. Risers |
| 33 | Laying of P.V.C. Pipesasper ISI-4985 (ISImarkedwith the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches tocorrectalignmentandgradients, cutting, jointingand testingcompleteasper specifications 315mm o/d PVC pipe of 4 Kgf. / sqcm (including length of riser 1.25 m) 21 no. Risers |
| 34 | Laying of P.V.C. Pipesasper ISI-4985 (ISI marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications 280mm o/d PVC pipe of 4 Kgf. / sqcm(including length of riser 1.25 m) 14 no. Risers |
| 35 | Providing and laying, jointing, fixing, testing ISI Marked G.I. Pipe (as per IS 1239) B Class, including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete. 100mm i/d |
| 36 | Providing and fixing elbow/bends of 90 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400mm |
| 37 | Providing and fixing elbow/bends of 90 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 38 | Providing and fixing elbow/bends of 90 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm |
| 39 | Providing and fixing elbow/bends of 90 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 40 | Providing and fixing elbow/bends of 45 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400 mm |
| 41 | Providing and fixing elbow/bends of 45 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 42 | Providing and fixing elbow/bends of 45 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm |
| 43 | Providing and fixing elbow/bends of 45 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 44 | Providing and fixing elbow/bends of 30 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400 mm |
| 45 | Providing and fixing elbow/bends of 30 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 46 | Providing and fixing elbow/bends of 30 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm |
| 47 | Providing and fixing elbow/bends of 30 degree 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 48 | Providing and fixing tail end piece 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400mm |
| 49 | Providing and fixing tail end piece 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 50 | Providing and fixing tail end piece 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm |
| 51 | Providing and fixing tail end piece 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 52 | Providing and fixing coupler/socket 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400mm |
| 53 | Providing and fixing coupler/socket 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 54 | Providing and fixing coupler/socket 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge315mm |
| 55 | Providing and fixing coupler/socket 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 56 | Providing and fixing equal tee 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400mm |
| 57 | Providing and fixing equal tee 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm |
| 58 | Providing and fixing equal tee 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm |
| 59 | Providing and fixing equal tee 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 280mm |
| 60 | Providing and fixing reducer 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 400mm x355mm |
| 61 | Providing and fixing reducer 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 355mm x315mm |
| 62 | Providing and fixing reducer 6kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315mm x280mm |
| 63 | Supply and installation of alfa valve including fittings etc complete in all aspects of 400 mm |
| 64 | Supply and installation of alfa valve including fittings etc complete in all aspects of 355mm |
| 65 | Supply and installation of alfa valve including fittings etc complete in all aspects of 315mm |
| 66 | Supply and installation of alfa valve including fittings etc complete in all aspects of 280mm |
| 67 | Supply and installation of Anti theft Mechanism for Alfa valve 400mm |
| 68 | Supply and installation of Anti theft Mechanism for Alfa valve 355mm |
| 69 | Supply and installation of Anti theft Mechanism for Alfa valve 315mm |
| 70 | Supply and installation of Anti theft Mechanism for Alfa valve 280mm |
| 71 | Cement concrete 1:3:6 ( M10) mixing by mechanical means using concrete mixer volumetric type , 100 mm thick ( for bridge) |
| 72 | DECKING SHEET (3 MM THICKNESS) ( for bridge) |
| 73 | Structural steel work in angles,tees, flats,riveted, including cutting, fixing all gusset plates, bolts, nuts, rivets etc. with hoisting and erecting in positionFor roof truss,wellcurbs,plategirdersetc. of anyspan for building for bridges upto 15M span |
| 74 | Any other item Misc. item |
| 75 | Any other item Please Enable Macros to View BoQ information |
