|
| 1 | Item Rate BoQ BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: CWE (A) AHMEDABAD NAME OF WORK : PROVISION OF ROAD OF 150 M ALONGWITH REAR GATE AT NCC DTE GUJRAT UNDER GE (A) AHMEDABAD CONTRACT NO: CWE (A)/ABD/ OF 2025-2026 SERIAL PAGE NO Bidder Name : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # SL NO ITEM DESCRIPTION Item Code / Make QTY UNITS Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT TOTAL AMOUNT With Taxes TOTAL AMOUNT In Words |
| 2 | Excavating over areas in soft and loose soil, n exc 1.5 m deep and getting out as specified. |
| 3 | Laying and compacting 150 mm thick (Compacted thickness) Granular Sub base Course (GSB) grading as per Grade I as specified Table 400-1 of MoRTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination there of as per the grading required the materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity and rolling with vibratory roller of capacity 80-100 KN static weight for achieving required compaction density of atleast 98% of the maximum Dry density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per table 900-1 of MoRTH specifications for Road and Bridge works 2013. |
| 4 | Material and Labour for Rolling and consolidating of formation surfaces including watering with 8 to 12 tonne power road roller consolidation to the required level gradient, camber etc in cutting/ filling in and depression complete all as specified and as directed by Engr-in-Charge. |
| 5 | Material and labour for laying and compacting 150mm thick (compacted thickness) Wet Mix Macadam (WMM) laid in two layers of 75mm each grading as per table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with wate to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-1OO KN static weight and consolidating to required gradient and camber complete all as specified and as directed. The finished surface tolerances to be as per Table 900-1 of MORTH specifications for Road and Bridge works 2013. |
| 6 | Material & Labour for preparing surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and prime coat bitumen emulsion on WMM @ 7.50 Kg per 10 Sqm as per clause 502.2.2. of MoRTH specification , complete all as specified and directed. |
| 7 | Provoding and consolidating 50 mm thick premix Dense Bituminous Macadam (DBM Grading -11) using min 4.5% VG 40 grade binder by weight of total mix aggregate gradation as per grading 2 of table 500-1 0 of MoRTH specification for road and bridge works 2013, rolled and compacted to required camber and gradient complete all as specified and directed. |
| 8 | Preparing black top surfaces by brusing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc, complete all as specified and directed. |
| 9 | Material and labour for applying evenly a priming/tack coat of VG 10 grade paving bitumen at 2.5 Kg per 10 Sqm by using mechanical sprayer. |
| 10 | Material and labour for providing bituminous premix asphaltic dense concrete, 40 mm consolidated thickness with 5.5% binder content by weight of total mix, with hydrated filler 2 % (If recommended in the trial mix) using mechnical paver, rolled and compacted to required camber and gradient and to achieve a smooth surface complete all as directed. |
| 11 | Material and labour for preparing bituminous surfaces of road and marking 2..5 mm thick centre lines, stop lines, dashes, arrows etc. and the like not exceeding 10 cm wide on roads pavements with hot applied thermoplastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instructions complete all as specified and as directed. |
| 12 | Providing and laying at or near ground level factory made kerb stone M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 Coarse sand) including making joints with or without groove (thickness of joints except at sharp curve shall not to more than 5 mm ), including making drainage opening wherever required complete. |
| 13 | Material and labour for 100 mm thick mooram/ red bajri filling in berms incl necessary rolling & watering complete. |
| 14 | Excavation in trenches , n exc. 1.5 m wide and n exc. 1.5 mtr in depth for fdn etc. and getting out in hard/dense soil. |
| 15 | Material and labour for PCC 1:4:8 type D2 (40mm graded aggregate) as in foundation filling & mass concrete. |
| 16 | Material and labour for RCC M-30 (20 mm graded aggregate) as in footing/ foundation etc. |
| 17 | Material and labour for RCC M-30 (20 mm graded aggregate) as in columns |
| 18 | Material and labour for fair finished flat form work to sides of concrete fdn rafts etc. |
| 19 | Material and labour for flair finished sqaure, rectangular or polygonal formwork to sides of pillars, posts, struts, cols and stanchios. |
| 20 | Material and labour for TMT bar 10 mm dia and over cut of length bent to shape required including cracking, bending, spirally for hooping for columns and binding with and including binding wire (anneled) not less than 0.9 mm dia complete all as directed. |
| 21 | -ditto- as above but TMT Bars 5mm dia and over upto 10mm dia as in stirrups. |
| 22 | Material and labour for rendering 10mm thick on fair faces of block masonry or on concrete surfaces CM 1:4 and finished even and smooth with out using extra cement. |
| 23 | Material and labour for preparing new plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant primer on surfaces of wall. |
| 24 | Material and labour for PCC 1:3:6 type C1for coping using 20mm graded stone aggregate all as directed.. |
| 25 | Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm in soil. |
| 26 | Removing excavated materials n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point. |
| 27 | Supply and fixing rolled mild steel framed work as in doors or gates of angles or other sections conforming to FE 290 gde E-165 with gusset plates, rails braces etc., complete drilled for fixing of steel sheeting or other covering and hanging and fixing complete. |
| 28 | Preparation of new or previously untreated steel surface of any description exc. 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 29 | Excavation in trenches in soft/loose soil not exc. 1.5m wide and not exc. 1.5 m in depth for laying of pipes and for poles/stay and struts not exceeding 10 Sqm on plan and getting out, excavated earth, forming bottom surfaces to required levelcomplete all as specified. |
| 30 | Supplying, laying and testing of LT UG cable, XLPE insulated, screened PVC bedded galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor 10 Sqmm 4 core complete all as specified and directed. Note: Earth work (Excavation, Returning & refilling and removal), cable protection HDPE pipe, GI protection pipe shall be measured and paid separately under respective item of BOQ. |
| 31 | Material and labour for Double Wall corrugated HDPE pipe, ISI marked of outer dia 50mm , inner dia 38mm SDR-21 of 4Kgf/Sqcm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/ duct or fixed on walls/pole including all conncetions, accessories like socket, couples, bends etc for protection of LT cable XLPE grade 1100 Volts complete all as specified and directed. |
| 32 | Supply and erection steel tubular poles in true vertical complete with cast iron base plate 6 mm thick 300X300mm, finial taper, plug, bolts, nuts & washers as specified type 410 SP-31(9.0 mtr long) duly panited with two coat of black bituminous paint internally through out and externaly for embeded portion and painting with one coat of red oxide primer, applying two coats of synthetic enamel aluminum pain on remaining exposed surface after errection complete painting with synthetic enamel paint of colour black and yellow alternate strip of 30cm width upto 1.6mtr from top and coping complete including making hole for enterance of cable for street light conection complete all as specified and directed.Note: Excavation, MS work and PCC work willl be measured and paid separately. |
| 33 | Material and labour for plain cement conceret (1:3:6) C1 type using 20 mm graded course aggregate foundation of poles etc. , complete all as specified and directed. |
| 34 | Material and labour for plain cement conceret (1:2:4) B1 type using 20 mm graded course aggregate for coping etc., complete all as specified and directed. |
| 35 | Material and labour for bracket made out of GI tubing 40mm dia medium grade GI pipe of length 1.50 mtr bent to required shape including fixing with MS nuts bolts 75mm long 12mm dia with 4 Nos & flat washer (3mm thick) 01 No for each including painting with aluminum paint over one coat of red oxide to the MS clamps & bracket etc complete all as specified and directed. |
| 36 | Supply and fix PVC/ DK thermoplastic cable junction boxes IP 65 with metric knockouts for cable, weather proof suitable for outdoor installstion for gate light and post top lantern, fixed on wall with srew & rawal plug and on GI pipe with suitable size MS calmp and nut-bolts washer of size 140X140X95 mm complete including one connector block three terminals and PVC cable gland 02 Nos for incoming and outgoing cables with provn of 01 Nos single pole MCBs 10-32 amps inside the box complete all as specified and directed at site. |
| 37 | Supply and fix LED security light fitting 70W (smart street lighting) new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminum housing with energy efficiency LEDs as lighting source and lens embedded PC cover having top opening separate driver compartment with IP 65 protection an automated fixture that uses integratedsensor to deduct motion or changes in light level brightness upto 50% and once deducted the motion it comes to 100% for few minute the again comes down upto 50% brightness and illuminating an area only when necessary and make elctrical connection complete all as specified and directed. |
| 38 | Supply and fix of PVC insulated & sheathed, round worksop cable three core 1.5 sqmm with multi stranded copper conductor for making connection from junction box to light fitting complete with suitbale size copper lugs complete all as specified and directed. |
| 39 | Material and labour for horizontal boring of holes under road, pavemnt, hard standing by trenchless technology using GI pipe of required dia and necessary machine suitable for 04mpa working pressure complete all as specified and directed.Note: HDPE pipe / GI pipe light grade will be measured and paid seperately under respected item. |
| 40 | Supply and fixing street light timer panel of capacity 6KW suitable for three phase supply including astronomical digital timer, contractor 32 Amps TP, MCB TPN 40 Amps for incomer complete all as specified and directed. |
| 41 | Supply, installation & fixing maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2 mm with copper bonding thickness of 250 micron with universal clamp made of SS earth enhancing compound shall be of 30Kg/Pit (resistivity is less than 0.12 Ohm meter) . The above arranements shall be provided with heavy duty earth poly plastic pit cover of 4000Kg load bearing capacity (Size: 270X40X200mm) complete all as specified and directed. |
| 42 | Supply and Fixing galvanized pipe 40mm diabore light grade in trenches/road/nallah or fixed along wall /pole including mild steel clmaps, screws etc, complete all as specified and directed. Total in Figures 0.0 0.0 INR Zero Only Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only Please Enable Macros to View BoQ information |
