|
| 1 | ARM REVOLVE ASSISTMain Frame: 0114 *3 mm thick M.S pipe and subordinate tube is of 088*3.0 large thickness M.S pipe. Handle: is made of 088 3 mm thick Pipe and 025 mm round M.S bright bar in bending design. All remaining frame is made by 088 *3mm thick MS pipe. Weight plates: Rubberized moulding round weight plates are used. Weight Plates Holder with spring lock and spare weights holder: is made by hard chrome plated mild stee!048 D!A pipe open front covered with half round cap and holder end is covered with heavy quality rubber ring of OD-68 mm and ID-48 mm with 10mm wall thickness for free weight noiseless operations. Bearing: Lubricated high grade6305 `2RS`steel ball bearing. Base plate: is OD166, ID 116, and 6 mm thick. Pins: are made up of M.S bright bar Bearing bushes: 075mm OD seamless pipe. Weight plate mounting pipe is of 048 mm MS pipe. Seat Frame: made up of hard chrome plated mild steel 48 DIA round pipe. Hardware All hardware`s uses button heads bolts and nuts made up of high tensile steel.Hand grips: Hand grips is used on handles wherever necessary made up of high-quality rubber and handle ends are covered with aluminum/pp/nylon caps with grub screw for long endurance. Closing caps: are of PP/NYLON/HDPE materia!. Laser cutting: profiles of 6mm and 4mm thick M.S sheet are used for connecting subordinates with each other.Rubber: Safety base pads. Anti-skid safety base pads made up superior rubber to prevent slippery and damage to floor. Heavy duty 20mm thick rubber pads are placed for resting handles for noise less operations Powders Coating. All components are chemically treated to seal exterior and interior surfaces against corrosion. The components are electro statically powder coated at minimum 80-100-micron thickness to make it resistant to scratch, corrosion and humidity in dual color combination.Safety Instructions and Exercise chart on machine - start and finish position chart stick on |
| 2 | GONDOLA SWINGMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.. Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform.Swing Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Min Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut. Pins: are made up of M.S bright bar. Bearing bushes: 089mm OD seamless pipe.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic.Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilized Safety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. stallation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 3 | XOXO PANELTEXTMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked 151239 Minimum 114 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. A.Play panel LLDPE (Linear Low-Density Polyethylene), roto-moulded Thickness: 6-8 mm wall thickness. Finish Seamless, anti-static, smooth surface UV Resistance. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts.Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilized Safety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation. Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 4 | PLAYFUL PANELMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 114 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.A.Play panel designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for engaging graphics through play. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts.Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilizedSafety Compliance Standards: EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional). Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges.Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 5 | DUETMain Structure Material: Stainless Steel 304 Grade, 1.5-2.5 mm thick pipe or tubeDimensions: Minimum 60-32 mm outer diameter (OD), 1.5-2.5 mm thicknessCap HDPE Heigh dencity polyetheline 20mm thickness.Fasteners Material: Stainless steel fasteners are specified to BS EN ISO 3506. Part 1 coversbolts, screws and studs.A.Safety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA) Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended |
| 6 | FISHY FUNNY SEE SAWMain Structure Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Handle and Leg rest Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 25 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Seat: designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for Spring: Heavy-duty coil spring, High-carbon steel or alloy spring steel, 18 mm-20 mm wire thickness, Coil height: Approx. 300 mm.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic.Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Shot Blasting surface treatment process using high velocity, steel abrasive Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilizedSafety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA) Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges.Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 7 | CHEERFUL CHURNMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS 1239 Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automaticPipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform.mgr Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding HeighPower Machine Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut. Pins: are made up of M.S bright bar.Bearing bushes: 089mm OD seamless pipe.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic.Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilizedSafety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges.Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 8 | Sea-SawMain Structure Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Handle and Leg rest Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 25 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60-80 microns), Bending with fullyA. automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Seat: designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for Spring: Heavy-duty coil spring. High-carbon steel or alloy spring steel, 18 mm 20 mm wire thickness, Coil height: Approx. 300 mm. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts.Surface Coating Primer: Shot Blasting surface treatment process using high velocity, steel abrasive Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilizedSafety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional). Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges.Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 9 | SIT `N` SNICKER SWING -Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zine primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.. Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform.Swing Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut.Pins: are made up of M.S bright bar.Bearing bushes: 089mm OD seamless pipe.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts.Safety Compliance Standards: EN 1176 (Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges.Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended. |
| 10 | [6.1.1]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1. 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) [Through Rate] Please Enable Macros to View BoQ information |
