Tender For Development Of Tourism Facilities At Wahkaliar(Overlooking Nohkalikai), Sohra, Meghalaya, North Garo Hills-Meghalaya

TDR : 54754935

Tender Notice
BOQ

12 Days Left

North Garo Hills , Meghalaya

Tender Brief : Tender For Development Of Tourism Facilities At Wahkaliar(Overlooking Nohkalikai), Sohra, Meghalaya

Document Fees
₹ 13810 /-

EMD
₹ 4143000.0 /-

Tender Value
₹ 13.81 Crore /-

Submission Date
02-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Civil Works
2	Plumnbing Works
3	Electrical Works
4	Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 30 mm, removal of stumps of such trees cut earlier and disposal of unserviceable material to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.B. By Mechanical Meansi. In area of non-thorny jungle
5	Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m
6	Earth work in excavation by manual mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 in in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 in and lift up to 1.5 in, as directed by Engineer-in-charge.(a) All kinds of soil
7	Earthwork in excavation by Mechanical means up to a depth of 2 m below the existing ground level tor foundation, trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils. ln ordinary rock (soft rock/ medium rock/ hard shale)
8	Earthwork in excavation by Mechanical means up to a depth of 2 m below the existing ground level for foundation, trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils. b. ln ordinary rock (soft rock/ medium rock/ hard shale)
9	Earthwork in excavation by manual means up to a depth of 2m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal Of surplus earth with all lead and lifts as directed and specified for the following classification of soils. (a) (a) All kind of soil (ordinary soil/hard soil/dense)
10	Construction of retaining walls/breast walls in cement mortar 1:5 as per drawing and Technical specification Clause 1604. III Marshy Soil. (iii) Stone Masonry in cement mortar 1:5
11	Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, completeb.i.100 mm
12	Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.(b) Stone soling (ii) 150mm
13	Plain cement concrete works in foundation bed for footing steps, walls, brick works etc below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)
14	Plain cement concrete works in foundation bed for footing steps, walls, brick works etc below plinth level as directed and specified including dewatering if necessary, and curingcomplete (shuttering where necessary shall be measured and paid separately).
15	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:a. Cement Mortar 1:6 (1 cement : 6 Coarse sand)
16	Random rubble masonry with hard stone in superstructure above plinth level and up to tirst floor level, including levemng up with cement concrete 1 :6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) at window sill, ceiling level and the like.a. Cement Mortar 1:6 (1 Cement : 6 Course Sand)
17	Earthwork in filling (excluding rock) in trenches, plinth, sides of foundation etc in layers not exceeding 20 cm thick including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift up to 1.5 ma. WIth available Excavated earth
18	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
19	Supplying, fitting and fixing in position reinforcement bars up to 1st floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)Thermo-Mechanically Treated bars
20	Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for Ft.C.C. work/ a.a. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)
21	Shuttering / Formwork Centering and shuttering lncluding strutting, propping etc. and removal of form for all heights complete and as directed by Engineer in charge.
22	Foundations, footings, bases of columns, etc. for mass concrete (using steel).
23	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc (using steel
24	Columns, Pillars, Piers, Abutments, Posts and struts (using steel).
25	Stairs/ spiral staircase, (excluding landings) (using timber)
26	Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
27	Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
28	Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards (using timber).
29	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level:M20 or 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
30	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, fillets, columns, pillars, posts and struts etc. above plinth level up to first floor level, excluding cost of centering, shuttering, finishing and reinforcement:M20 or 1 :11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
31	Reinforced cement concrete work in beams, slabs, roofs having slope up to 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to first floor level, excluding the cost of centering, shuttering, finishing and reinforcement
32	Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineerin-charge.(a)All works up to plinth level
33	Extra for providing richer mixes. (a) Providing M-30 grade concrete
34	Half brick masonry with common burnt clay (non modular) lst class bricks in superstructure above plinth level up to first floor level (a) Cement mortar 1 :3 (1 cement: 3 coarse sand)
35	Half brick masonry with common burnt clay (non modular) lst class bricks in superstructure above plinth level up to first floor level (b) Cement mortar 1 :4 (1 cement: 4 coarse sand)
36	Half brick masonry with common burnt clay (non modular) 1stclass bricks in foundations and in plinth:
37	Providing 12mm thick cement plastering in cement mortar 1:2, 1:3, 1:4 including cleaning the surface, curing and carriage of all material within 200m complete as per Technical Specification. In cement Mortar 1:3
38	12mm thk cement plaster in single coat on rough side of single or half brick wall for columns
39	15 mm cement plaster on the rough side of single or half brick wall of mix:
40	15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed.
41	15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: (b)1 :4 (1 cement: 4 fine sand)
42	Rough cast plaster up to 10 height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, underlayer 12 mm cement plaster 1 :4 (1 cement: 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.
43	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to lS:733 and lS:1285, fixing with dash fasteners of required diameter and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and panelling to be paid for separately):
44	For fixed portion
45	Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
46	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing Of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)
47	Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
48	Providing and fixing fire resistant door frame of section 50x60 mm on horizontal side & 35x60 mm on vertical sides having built in rebate made out of 1.6 mm thick Gl sheet (Zinc coating not less than 120 gms/sqm) suitable for mounting 120 minutes Fire Bated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96 Kg/cum. The frame will have a provision of G.I, Anchor fasteners 14 nos. (5 each on vertical stile & 4 on horizontal rail of size M10 x 80) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges Of Size 100x89x3 mm for fixing of fire rated glazed shutter. The frame shall be finished with an approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer-in-charge.
49	Providing and fixing glazing in fire resistant door shutters,fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I.sheet (zinc coating not less than 120 gm/sqm) of size 20x33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c, including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading & special ceramic tape of 5x20 mm size etc. complete in all respect as per NBC 2016, IS:16231 (Part 3):2016 and as per direction of Engineer-in-charge
50	with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (E120). The manufacturer have to give test report/ certification of fire glass and the glass should have the stamp showing the value of E, EW & El. The glass shall be tested in approved NABL accredited lab or by any other acoreditation body which operates in accordance with lSO/lEC 17011 and accredits labs as per lSO/lEC 17025 for testing and calibration scopes shall be eligible.The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.
51	Providing wood works in frames of doors, window, clerestory window and other frames, wrought frame and fixed in position with hold fast lugs or with dash fasteners of required diameter and length.(c) with first class local wood (ii) Champa/ Diengrai
52	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length a. With Teak wood/ Sissu wood.
53	Providing and fixing panelling or glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel insert excluding portion inside grooves or rebated to be measured). Panelling for panelled and glazed shutter 25mm to 40mm thick: (c) With 1st class local wood (ii) Champa/ Diengrai
54	Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1 St class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
55	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)a.With Teak wood/ Sissu woodii. 30 mm thick shutters
56	Providing and fixing bright finished brass handles with screws etc. complete: (b)125 mm
57	Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc.complete as per direction ot Engineer-in-Charge.
58	Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar
59	Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
60	Providing and fixing lSl marked M.S. pressed butt hinges bright finished with necessary screws etc. complete:
61	Providing and fixing bright finished brass door latch with necessary screws etc.complete:(b) 250xl6x5 mm
62	Providing and fixing lst marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete: (a) 125mm
63	Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete(b)200x10mm
64	Providing, fitting and fixing steel windows (including ventilators) of standard rolled steel sections as per relevant I.S.Code, joints mitred and welded with 15x3xl00mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65 mm and not less than 15 mm wide) bolting device, steel handles, pegs, stays of 300 mm long etc. complete including providing 12x12mm square bars duly welded to steel frame at not more than 12 cm c/c applying a priming coat of red-lead paint etc. complete as per drawing. (a) Openable
65	Providing & fixing glass panes with putty and glazing clips in steel doors,windows,clerestory windows, all complete with: (a) 5.5 mm thick glass panes
66	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge: € With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)
67	Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge: b. With float glass panes of 4.0 mm thickness (weight not less than 10 kg/sqm)
68	Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
69	Applying ready mixed priming coat of approved brand and quality as per specifications
70	Applying one coat of water thinnable cement primer of approved brand and manufacture on surfaces: Water thinnable cement primer
71	Applying Priming coat: With ready mixed red oxide zinc chromate primer Of approved brand and manufacture on steel galvanised iron/ steel works
72	Applying priming coat:a.With ready mked pink or Grey primer Of approved brand and manufacture on wood work (hard and soft wood)/ with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood
73	Providing and applying Plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
74	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications, including scaffolding:
75	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications, including scaffolding: c.Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture
76	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade, including scaffolding:
77	Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to ls:15622, ofapproved make, in all colours and shades laid on 20 mm thickcement mortar 1:4 (1 cement: 4 coarse sand), jointing withgrey cement slurry @ 3.3 kg/sqm including grouting the jointswith white cement and matching pigments etc„ complete. (a) Size of tile 600x600mm
78	Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to lS:15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). Premium range
79	Providing and fixing lst quality ceramic glazed wall tiles conforming to ls:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls,skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(a)Normal range
80	Providing and laying paver over a base of 100 mm compacted sand gravel including cutting where necessary finished with flush pointing with cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (a) 80 mm thick
81	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
82	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
83	Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. ln gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
84	Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ opening/ railing with M.S. flats at required spacing in frame all round, square or round M.S. bars with round headed bolts and nuts or screws
85	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gins/sqm (both side inclusive) as per ls:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia. x 50mm long with 6 mm dia. bolts, other flange Of cleat fixed to the angle hangers of 25xloxo.50 mm of required length with nuts & bolts Of required size and other end Of angle hanger fixed with intermediate G.I. channels 45xl 5xO.9 mm running at the spacing of 1200 mm centre to centre, to the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, Shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips
86	made out of 2.64 mm dia. x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges Of 20 mm and 30 mm long, the perimeter of ceiling fb(ed to walvpartition with the help Of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing Of gypsum board to ceiling section and perimeter channel with the help Of dry wall screws Of size 3.5x25 mm at 230 mm a/c, including jointing and finishing to a flush finish Of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides ol joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost Of painting with:
87	Providing and fixing, in position concealed G.I. section for wall panelling using board of required thickness fixed on the W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610mm c/c in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm c/c with fully threaded self-tapping dry wall screws, Board is fixed to the W' profile with 25 mm countersunk ribbed head screws @ 200 mm c/c., all complcte as per drawings & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. (b) Multipurpose cement board reinforced with suitable fibre cement screw. (i) 8 mm thick cement fibre board as per lS:14862
88	65 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1 :2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layer 15 mm thick cement hardener consisting of mix 1 :2 (1 cement hardener mix: 2 graded stone aggregate, 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture's specifications. This includes cost of cement slurry, complete.
89	Cement concrete floor topping 1:1:2 (1 cement: 1 coarse sand: 2 stone aggregate) finished with a floating coat of neat cement, including cement slurry, completeb. 20 mm thick
90	Cement concrete floor topping 1:3:6 (1 cement: 3 coarse sand: 6 stone aggregate) finished with a tloating coat Of neat cement, including cement slurry, complete.(b) 20 mm thick
91	Providing, Supplying,fitting,fixing and laying of dressed stone block walling and tile slab (Cherra/ local stone block) laid on 25mm thick base in cement mortar 1 :3 and jointed with grey cement slurry including clearing, directed.
92	Providing, Supplying, fitting, fixing and laying of dressed stone block walling and tile slab (Cherra/ local stone block) laid on 25mm thick base in cement mortar 1 :3 and jointed with grey cement slurry including clearing, rubbing etc. complete as directed.b. Cherra stone block (300x150x75)
93	Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made Of G.I. wire of dia. 3 mm including strengthening with 2 mm dia. wire or nuts, bolts and washers as required complcte as per the direction Of Engineer-in-charge.
94	Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia. 10 in openable length (total length 90 in), having 50 nos. rounds per 6 in length, up to 3 in height of wall with existing angle iron 'Y. shaped placed 2.4 in or 3.00 in apart and with 9 horizontal P.B.T. reinforced barbed wire, stud tied with G.I. staples and a.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-incharge, with reinforced barbed tape (Pl.B.T.)/ Spring core (2.5 mm thick) wire Of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gin/in (cost of M.S. angle, C.C. blocks shall be paid separately).
95	Construction of unlined surface drains of average cross sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3 m and lead of 50 m (average lead 25 m) as per Technical Specification Clause 307. B. Mechanical Means
96	Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming stone screening /binding materials to fill up the interstices of coarse aggregates, watering and compacting to the required density Grading 1 as per Technical Specification Clause 404.(B) By Mechanical Means
97	Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming stone screenings /binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405B. By Mechanical means
98	(i) Providing and applying tack coat with penetration grade bitumen (S-90) using bitumen pressure distributor at the specified rate of 0.50 kg/sqm on the prepared WBM surface not primed, cleaned with hydraulic broom as per Technical Specification Clause 503
99	Providing laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.2
100	Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510(II) Bitumen 60/70 grade
101	Maintenance of drains due to erosion including repair, clearing, cleaning, reshaping, regrading, deepening of side drains as well as catch water drains as per Technical Specification Clause 1907.
102	Providing precast cement concrete Jali 1:2:4 (1 cement: 2coarse sand: 4 graded stone aggregate 6 mm nominal size ),reinforced with 1.6 mm dia. mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete,excluding plastering of the jambs, sills and soffits
103	Sand gravel (chapter 33-basic rate of major material) (SL.NO 12)- river sand
104	Stone aggregate (blasted stone aggregate 20mm down graded)(chapter 33-basic rate of major material) (SL.NO 11)
105	Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and comers, all necessary fittings complete,including applying a priming coat of approved steel primer. (a) Using M.S. angels 40x40x6 mm for diagonal braces
106	Providing corrugated galvanised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvanised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc.
107	Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts,nuts and washers, etc., including making necessary connections with rain water pipes complete
108	Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.
109	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed togcther at the end by end locks,mounted on specially designed pipe shaft with brackets, side guides and arrangements tor inside and outside locking with push and pull operation complete, including the cost Of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire Of adequate strength conforming to ls:4454 - part 1 and M.S. top cover Of required thickness tor rolling shutters. (a) 80xl.25 mm M.S. laths with 1.25 mm thick top cover
110	Providing and fixing ball bearing for rolling shutter
111	Making soak pit 2.5 in diameter 3,0 metre deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter,1.8 in long complete as per standard design
112	Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed. (a) First 5 Km
113	Providing and fixing pre-coated galvanised iron profile sheets (size, shape and pitch Of corrugation as approved by Engineer-in-charge) 0.50 mm(+O.05 a/o) total coated thickness with zinc coating 120 grams per sqm as per ls:277, in 240Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film Of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 mcter or as desired by Engineer-incharge. The sheet shall be fixed using selfrdrilling/ selftapping screws of size (5.5x55 mm) with EPDM seal, complete up to any pitch in horizontav vertical or ciirved surfaces, excluding the cost of purlins. rafters and trusses and including cutting to size and shape wherever required.
114	Providing and fixing pro-coated galvanised steel sheet roofing accessories 0.50 mm (+0.05 a/a) total coated thickness, Zinc coating 120 grams per sqm as per ls:277, in 240 Mpa Steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ selftapping screws complete:
115	Ridge
116	Gutter: Roof
117	Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in Charge and consisting of: (i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1cement: 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to12 mm nominal size spreading @ 0.008 cum/sqm thoroughly embedded in the 2nd layer.
118	Grouting the joints offlooring tiles having joints of 3mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling, grouting and finishing complete as per direction of Engineer-in-charge.
119	Extra for carriage including loading and unloading and all charges complete beyond the initial lead of 5 Km.
120	Boulders
121	Stone Aggregates
122	Cement
123	Steel
124	Bricks
125	NON-SCHEDULED ITEMS (AS PER MARKET RATE)
126	MAIN BUILDING
127	Invisible Hidden Ghost Wood Sliding door fittings
128	Smart door lock
129	Berger paints
130	Externo Stark Puro Tiles
131	Rockdeck (Rate Analysis)
132	Venitto sand (Polish) (800x300)mm
133	Marfig Pearl
134	Vibrant Woven Vinyl flooring
135	Pare Soffit
136	Louvers 50mm thick x 2900mm long
137	Brick cladding
138	Panelled glass
139	Thatched roof
140	Bamboo support
141	Glass railing (10mm)
142	Ittimi rope tilt
143	Bamboo Ceiling
144	Alfresco live outdoor
145	Double Laminated Shingles
146	Ridge for Double laminated Shingles
147	UPVC gutter with accessories
148	Stone Cladding
149	WPC decking including frame
150	VILLAGE SHOP
151	Earthwork in excavation by manual means up to a depth of 2m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal Of surplus earth with all lead and lifts as directed and specified for the following classification of soils. (a) (a) All kind of soil (ordinary soil/hard soil/dense)
152	Providing soling with stone/ best quality picked jhama brick,sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete (b)(i) 100mm
153	Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).
154	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with
155	Random rubble masonry with hard stone in superstructure above plinth level and up to tirst floor level, including levemng up with cement concrete 1 :6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) at window sill, ceiling level and the like.
156	Earthwork in filling (excluding rock) in trenches, plinth, sides of foundation etc in layers not exceeding 20 cm thick including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
157	Supplying, fitting and fixing in position reinforcement bars up to 1st floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B walling including straightening, cleaning, cutting and bending to proper shapes and length as per details,supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs,spacers etc. complete. (Rates inclusive of all wastage,lappage, hooks, chairs, anchorage etc. and no measurement for the same is required) (b) High Yield Strength Deformed bars or Tor Bars
158	Providing form work of ordinary timber planking of thickness not less than 25mm and removal of the same for concrete members so as to give a rough finish including centering, shuttering, strutting and propping etc., for height of propping and centering of supporting floor to the soffit of the concrete member not exceeding 4.0M as specified for the following items:
159	Foundations, footings, bases of columns, etc. for mass concrete (using steel)
160	Columns, Pillars, Piers, Abutments, Posts and struts (using steel).
161	Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel).
162	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost Of centerjng, shuttering, finishing and reinforcement- All work up to plinth level:
163	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, fillets, columns, pillars, posts and struts etc. above plinth level up to first floor level, excluding cost of centering, shuttering, finishing and reinforcement:
164	Half brick masonry with common burnt clay (non modular) lst class bricks in superstructure above plinth level up to first floor level (b) Cement mortar 1 :4 (1 cement: 4 coarse sand)
165	15 mm cement plaster on the rough side of single or half brick wall of mix:
166	50 mm thick cement concrete flooring with concrcte hardener topping, under layer 38 mm thick cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting Of mix 1 :2 (1 cement hardener mix: 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg Of cemem or as per manufacturer's specifications. This includes cost of cement slurry, complete.
167	Steel work riveted and/ or bolted/ riveted in built up sections, frame work including cutting, hoisting, fixing in position and applying a priming coat of red- lead paint up to 4.6m height above plinth including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed.
168	Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and comers, all necessary fittings complete,including applying a priming coat of approved steel primer. (a) Using M.S. angels 40x40x6 mm for diagonal braces
169	Applying one coat of water thinnable cement primer of approved brand andmanufacture on surfaces
170	With ready mixed red oxide zinc chromate primer Of approved brand and manufacture on steel galvanised iron/ steel works
171	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications, including scaffolding:
172	Providing corrugated galvanised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvanised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc.
173	Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts,nuts and washers, etc., including making necessary connections with rain water pipes complete
174	Providing ridges or hips Of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.
175	Extra for carriage including loading and unloading and all charges complete beyond the initial lead of 5 Km.
176	Boulders
177	Stone Aggregates
178	Cement
179	Steel
180	Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings with one step cpvc solvent cement,trenching,refilling and testing of joints complete
181	100 mm
182	75 mm
183	50 mm
184	32 mm
185	Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 in spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
186	25mm nominal dia pipes
187	Supplying,fitting and fixing soil waste and vent pipes
188	Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete with sand cast iron S&S as per IS:1729/IS: 3989
189	Supplying fitting and fixing complete single phase open well submersible pumps sets or similar. 2HP
190	POLYETHYLENE WATER TANK
191	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ls:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
192	2000litre capacity
193	5000litre capacity
194	SANITARY FITTINGS (Rate as per Jaquar Costumer Guide Vol 19.2 Catalogue 2024)
195	Wash basin for Toilet
196	JDS-BLM-25907N Thin Rim Table top Basin.530 x 420 x 140mm
197	ALD-727L130 Click Clack Waste coupling 32mm size Full Thread with130mm height
198	ALD-769L300X190 Bottle trap 32mm Size with 300mm & 190mm long wall connection pipes & wall flange.
199	FLP-5191PM 3-Hole Basin Mixer with Popup Waste System
200	FLP-5021PM Pillar Cock with Extension Body
201	FLP-5053PM Angular Stop Cock with Wall Flange
202	FLP-5037PM Bib Cock with Wall Flange
203	AKP-35795 Swivel Mirror 630 x 445mm Rectangular Shape
204	ACN-1137N Soap dispenser with Metallic bottle
205	Hand Dryer- Flash HDR-SSF-AK2807 Flash touch-free inframed hand dryer with 1150W rated power 7 carbon brush motor.
206	AKP-35711PS Single Towel Rail 600mm Long, Stainless Steel
207	AKP-35721P Towel Ring Square
208	AHS-1553 Paper Holder with Flap Recessed Type (Stainless Steel)
209	Water closet for S type
210	SLS-WHT-6953BIUFSMRimless, Blind Installation Wall Hung WC With UF Soft Close Slim Seat Cover, Hinges And Accessories Set,Size: 375x520x400 mm
211	JCS-WHT-2431S Single Piece Concealed Cistern Body (Front or Top Actuation) with Installation Kit & “S-Type”drain pipe connection set forWall Hung WC (without FlushControl Plate)
212	JCP-CHR-152415 Control Plate Opal
213	Water closet for P type
214	SLS-WHT-6953BIUFSMRimless, Blind Installation Wall Hung WC With UF Soft Close Slim Seat Cover, Hinges And Accessories Set,Size: 375x520x400 mm
215	JCS-WHT-2431P Single Piece Concealed Cistern Body (Front or Top Actuation) with Installation Kit & “P-Type”drain pipe connection set for Wall Hung WC (without Flush Control Plate)
216	JCP-CHR-152415 Control Plate Opal
217	ALD-577 Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook with N.R.V (Back Flow Preventer)
218	URS-WHT-13255 Urinals without sensor with fixing Accessories Size: 480 x 300 x 740 mm
219	SNR-51097 Sensor Flushing Valve for Urinal with Complete Kit (Battery Operated)
220	Model no: 1810-UC/1110UC, JSE-CHR-110UC450OX Curved shaped urinals partition with frosted glass 10mm , Chrome finish.
221	SHP-BLK-ST86112 Shower panels GLASSY-BLACK 1400x 250mm
222	Shower drain channel-Tile insert-Square Item code: 16-0205-05 (102 x 102)mm
223	Shower drain channel-Tile insert Item code: 16-0203-16 (450 x 125 x 30)mm
224	FLP-5165PM Single Lever Sink Mixer with Swinging Spout on Upper Side (Wall Mounted Model) with Connecting Legs & Wall Flanges
225	ERD-WHT-VO25 ERICA VERTICAL (Digital) 25Litres
226	PHYSICALLY CHALLEGED TOILET
227	WAC-SAP-BR0600CS Grab bar 692mm Long, Satin
228	WAC-SAP-BG0800CS Grab bar Vertical Swing, Satin
229	WAC-SAP-BAI090CS Grab bar Left 90° Angle,Satin
230	DIS-WHT-93801 Wall Hung Basin with Fixing Accessories, Size :650x565x155 mm
231	DIS-WHT-93753P180UFRimless Bowl For Coupled WC with UF Soft Close Seat Cover, Hinges, Fixing Accessories, Size:390x610x800mm P-Trap- 180 mm
232	DIS-WHT-93201 Cistern With Dual Flush Cistern Fitting
233	Providing and fixing Multi floor trap @320/ per piece inclusive of GST @18% for 4'' in Bathroom and Toilets, complete and as directed.
234	KRISTALL TREND,BKT-CHR-31651200X : Corner entry shower enclosure with door sliding to both sides - 4 parts Glass: 6mm Finish: Chrome (H: 1850 W: 1200 X 1200)mm
235	ESA-GBL-LDG1212 Artificial Marble Ledge 1200 x 1200mm
236	Model No. 1810-D/ 1110-D: Wall to wall shower Enclosure only door with towel rod & handel -1 part H: 1950 W:801-1000
237	GALAXY BLACK ESA-GBL-LDG0812 Artificial Marble Ledge 801 - 1200mm
238	Double Bowl Exclusive Size: 1139 x 498 x 245mm (Black) 13-0312-02
239	INTERNAL PIPELINE (Rate as per Market Rate)
240	PVC pipe for Soil pipe, Waste pipe and Urinals Pipe
241	110mm dia. (Soil pipe)
242	75mm dia (Waste pipe)
243	50 mm dia (Waste pipe)
244	90 Degree PVC bend
245	110 mm dia
246	75 mm dia.
247	50 mm dia.
248	90 Degree PVC bend with Doors
249	110 mm dia
250	75 mm dia.
251	50 mm dia.
252	45 Degree PVC bend
253	110 mm dia
254	75 mm dia.
255	50 mm dia.
256	PVC single ‘Y’
257	110 mm dia
258	75 mm dia.
259	50 mm dia.
260	PVC coupler
261	110 mm dia
262	75 mm dia.
263	50 mm dia.
264	PVC cleaning pipe
265	110 mm dia
266	75 mm dia.
267	PVC End Cap
268	110 mm dia
269	75 mm dia.
270	PVC cowl
271	110 mm dia PVC cowl
272	75 mm dia PVC cowl
273	SWIMMING POOL
274	MAIN POOL
275	Filters
276	Fiberglass reinforced tank and swing away water diffuser with top Mountmultiport valve (700 mm 'dia')
277	Make: Pentair USA
278	Recirculation pump
279	Self Priming pumps.Pump body and prefilter in cast iron Motorshafts instainless steel AISI-304, impeller in HT200, mechanical seal in graphite.with motor -2900 rpm, 1.1 kw, 220-380V, 1.5HP, protection IP-55 and insulation class-F.
280	Make: Pentair USA
281	WATER TREATMENTS
282	Dosing Pump
283	CHLOR #320 1PK
284	Make: Lyxar
285	POOL BASIN ITEMS
286	Main Drain
287	Wall inlet 2\\" slipwith 1.5\\" slip bushing white
288	Make: Pentair USA
289	Wall Inlet
290	Wall inlet 2\\" slipwith 1.5\\" slip bushing white
291	Make: Pentair USA
292	Suction Inlets ( Vacuum points)
293	Vacuum fitting in white ABS with 50/2 threaded.
294	Make: Pentair USA
295	Ladder
296	Standard Ladder 3 Steps AISI 304
297	Ladder
298	Standard Ladder 4 Steps AISI 304
299	POOL SIDE EQUIPMENTS
300	Skimmer
301	Make: Pentair USA
302	UNDERWATER ILLUMINATION
303	Underwater Lights
304	Surface Mounted Light 441 leds warm white 20W/12V
305	Make: Lyzar
306	Transformer for lights
307	Power: 400w
308	SWIMMING POOL MAINTENANCE ACESSORIES
309	Telescopic Handle
310	2X240 cm Ribbed pole - 1.1mm thick
311	Make: Pentair USA
312	Hose Pipe (Floting Hose)
313	Extruded PE. ∮1 1/2\\" - 15M
314	Make: Pentair USA
315	Vaccum Head
316	Make: Pentair USA
317	Shallow Net
318	Aluminum leaf skimmer (blue anodized handle)
319	Make: Pentair USA
320	Deep Net
321	Aluminum frame deep rake(Bule anodized handle)
322	Make: Pentair USA
323	Brush
324	18\\"/45cm standard curved polybristle wall brush
325	Make: Pentair USA
326	Test Kit
327	Basic PH &CL test kit
328	Make: Pentair USA
329	Pool Plumbing
330	Providing all necessary plumbing using u-PVC Schedule 40 pressure Pipes with plain socket suitable for solvent cement jointing conforming toIS:4985/2000 & fittings conforming to IS 7834/87. Cut to required lengths including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs etc.The plumbing installation shall be tested to a pressure of 10 Kg/Sq.cm. for a period of 4 hours before covering with mortar. The rate includes all uPVC ball valves and non return valves as required and directed by the consultant. The pipe line will supported by proper MS support (duly pianted ) in the plant room and encased in concrete when underground. (All civil work support will be provided by the clinet).
331	Make: Paras/Astral/Equiv.
332	ELECTRICAL CONTROL PANEL and Wiring
333	Design, Manufacture, Supply, of Control panel constructed out of 1.5 - 2mm thick MS sheet steel fabricated cubicle type panel & panel degree of protection IP 41. The panel shall be complete incoming MCCB/ MCB, suitable size link complete with VAF digital electronic meter and 50/5 Amps suitable VA, CT's. set & complete with direct on line starter/ star delta starter, automatic/manual mode selection switch & earthing connector etc as required. whisch is sutable for pumps 4hp three phase380/440 VAC 50 hz.
334	Make: Polycab/Havels/Equiv.
335	Glass Mossiac Tiles
336	Size: 20x20mm
337	Rate Inclusive of materials and labour Item Rate BoQ BoQ_Ver4.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: Directorate of Tourism Name of Work DEVELOPMENT OF TOURISM FACILITIES AT WAHKALIAR(Overlooking Nohkalikai), SOHRA, MEGHALAYA Contract No: Name of the Bidder/ Bidding Firm / Company : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT Without Taxes TOTAL AMOUNT With Taxes TOTAL AMOUNT In Words
338	INTERNAL WORK
339	Concealed wiring in looping system with 2x1.5 mm² PVC insulated single core cable of 600V grade in heavyguage PVC pipe including occuping and fitting of elbows, bends, fees, junction box etc. including requird size of MS Conceal boxes and front plate for housing of switches socketsfan regulator bell push etc complete to light point.
340	(a) Long Point upto 10 mtr
341	(b) Medium Point upto 6 mtr
342	(c) Short Point upto 3 mtr
343	Wiring as in item no.20 above to light plug point when fixed elsewhere with continous earth wire complete.
344	(a) Long Point upto 10 mtr
345	(b) Medium Point upto 6 mtr
346	(c) Short Point upto 3 mtr
347	Wiring as in item No.1 complete to a light plug point when fixed on the same board.
348	Wiring as in item No.20 above to a Power Plug Point with 2x4 mm² including supplying and fitting of 15 Amp modular switch socket combined with continous earth wire to a Power Plug Point Complete
349	(a) Long Point upto 10 mtr
350	(b) Medium Point upto 6 mtr
351	(c) Short Point upto 3 mtr
352	Wiring as in item No.20 above to a ceiling Fan/Exhaust Fan point.
353	(a) Long Point upto 10 mtr
354	(b) Medium Point upto 6 mtr
355	(c) Short Point upto 3 mtr
356	Wiring as in item No.20 above to calling Bell/Bell Indicator point.
357	(a) Long Point upto 10 mtr
358	(b) Medium Point upto 6 mtr
359	Wiring as in item No.20 above for Staircase/ 2 Way Switch wiring.
360	(a) Long Point upto 10 mtr
361	(b) Medium Point upto 6 mtr
362	Drawing of Main and Sub-Main Line wiring as inn item No.20 above with VIR or PVC Single Core 250V Grade Cable.
363	(a) With 2x2.5 mm² copper wire
364	(b) With 2x4 mm² copper wire
365	Drawing 3 phase Main Line 4 wire with DGSD approved VIR or PVC cable 660 V grade in Heavy Guage 16 SWG Regid pipe Including with all necessary accessories.
366	(c) With 4x6 mm² copper wire
367	(d) With 4x10 mm² copper wire
368	Supplying, fitting & fixing complete 240/415 V Al. Bus-Bar chamber.
369	A. Economy Sheet Steel 50Hz. 240/415 V.
370	(ii) TPN 4 Ways.
371	(c) 100 Amp 415 V Capacity.
372	Supplying & fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB's for AC application till 63 A
373	A. Single Pole 240/410 V
374	(a) 0.5-6 Amp
375	(b) 6-32 Amp
376	Supplying, fitting & fixing of DX3 Isolators for AC applications upto 125 A.
377	C. Four Pole 415 V
378	(b) 40 Amp
379	Supplying, fitting and fixing of Moulded Case Circuit Breaker (MCCB's) of the following Amp capacity.
380	B. With breaking capcity of 20 kA
381	(iii) Four Poles
382	(b) 80-100 Amp
383	Supplying, fitting & fixing if Distribution Board ETPN DB's for MCB, Isolator, RCCB and RCBO.
384	B. IP 43-#1K 09 with metal door
385	(b) 6 way 8+18 Module
386	(c) 8 way 8+24 Module
387	Supplying, fitting and fixing of LED Batten surface or wall mounted with all necessary accssories.
388	(b) With Aluminium housing & integrated electronic driver.
389	(ii) 18 w (1182x23x37) mm
390	Supplying, fitting and fixing of LED PANEL LIGHTING surface or wall mounted with all necessary accessories.
391	(a) 2x2 (595x595x65) mm LED luminarie.
392	(i) 18 W
393	(ii) 24 W
394	Supplying, fitting and fixing of LED DOWNLIGHTS surface or wall mounted with all necessary accessories.
395	(b) Recess mounted pressure die-cast aluminium luminaire in powder coated whited finish with drop down PC diffuser with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver.
396	(i) 5 W ceiling cutout:ø 155 mm, height: 45 mm
397	Supplying, fitting and fixing of LED MIRROR LIGHT surface or wall mounted with all necessary.
398	Supply, Installation, Testing & Commissioning of 1x9 watt LED Mirror light fixture wall mounted with electronic high efficiency electronic driver as complete as required. (Phillips Make, Cat No-31083 shell or equivalent)
399	(a) LED Mirror Lights.
400	Supplying, fitting and fixing of LANDSCAPE LIGHTS surface or wall mounted with all necessary accessories.
401	(b) Family of post top lantern designed to complement the geometry of the area (design from the renaissance era yet with a modern look using new generation technology in LED).
402	(ii) 50 W suitable for pole dia ø 76 mm
403	(f) Decorative UP-down luminaire with wall surface mounting using COB LED as light source.
404	(i) 15 w
405	(h) Aesthetically designed die-cast aluminium landscape luminaire for downward lighting with high power LED as light source.
406	(i) 16 w (for Bollards)
407	Supplying, fitting, connecting, testing and commissioning of calling Bell/Bell Indicator type suitable for 230 V as well as battery operated complete with all necessary accessories.
408	(a) Dingdong Bell
409	Supplying, fitting & fixing of exhaust fan double self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts and other petty accessories as required.
410	(a) Domestic Exhaust Fans
411	(i) 150 mm
412	Providing, laying, connection, testing & commissioning of the following sizes of 1100 V PVC/XLPE Armoured Cables with Alluminium conductor as per ISI code in bracket, trenches sand cushioning with laying etc and refilling the same in layers or by supporting them in walls and all other accessories as required.
413	(d) With 3.5 core 70 mm² .
414	Supplying, fitting and fixing of Copper lightning Arrester with 5 nos. Finger at the top & copper base plate at the bottom.
415	(b) with 5ft high copper rod.
416	Supplying, fitting & fixing earthing with copper earth plate 600x600x6 mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt etc complete as required.
417	(a) Copper earth plate electrode.
418	Supplying and laying of 15 mm x 5 mm GI/Copper Strip at 0.50 mtrs, below ground.
419	(a) with 25 mm x 5 copper strip.
420	Supplying, fitting and fixing of 440 Volt grade Four pole change over Main Switch (Best Quality)
421	100 Amp capcity.
422	Concealed wiring in looping system with 2x1.5 mm² PVC insulated single core cable of 600V grade in heavyguage PVC pipe including occuping and fitting of elbows, bends, fees, junction box etc. including requird size of MS Conceal boxes and front plate for housing of switches socketsfan regulator bell push etc complete to light point.
423	(a) Long Point upto 10 mtr
424	Drawing of Main and Sub-Main Line wiring as inn item No.20 above with VIR or PVC Single Core 250V Grade Cable.
425	(b) With 2x4 mm² copper wire
426	Supplying & fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB's for AC application till 63 A
427	A. Single Pole 240/410 V
428	(a) 0.5-6 Amp
429	(b) 6-32 Amp
430	Supplying, fitting & fixing of DX3 Isolators for AC applications upto 125 A.
431	A. Double Pole 240 V
432	(b) 40 Amp
433	Supplying, fitting & fixing if Distribution Board SPN DB's for MCB, Isolator, RCCB and RCBO.
434	B. IP 43-#1K 09 with metal door
435	(c) 12 way + 12 Module
436	Supplying, fitting and fixing of LANDSCAPE LIGHTS surface or wall mounted with all necessary accessories.
437	(b) Family of post top lantern designed to complement the geometry of the area (design from the renaissance era yet with a modern look using new generation technology in LED).
438	(ii) 50 W suitable for pole dia ø 76 mm
439	Providing, laying, connection, testing & commissioning of the following sizes of 1100 V PVC/XLPE Armoured Cables with Alluminium conductor as per ISI code in bracket, trenches sand cushioning with laying etc and refilling the same in layers or by supporting them in walls and all other accessories as required.
440	(a) With 3.5 core 25 mm² .
441	(b) with 5ft high copper rod.
442	ELEVATOR SPECIFICATIONS
443	CAPACITY (kgs): 6 persons
444	SPEED (mps): 0.7 mps
445	RISE (m): 12.7m
446	STOPS :5 stops with opening on the same side
447	DRIVE: VVVF Regeneration (Closed loop)
448	POWER SUPPLY: 400/415 Volts (3 phase AC)
449	OPERATION: Full collective operation
450	CAR GROUP: One Car (Simplex)
451	MACHINE: PM Gearless (Located in shaft on top of guide rails)
452	TRACTION MEDIA: Flat coated steel belt
453	CAR FINISH: Stainless Steel - Hairline finish
454	FALSE CEILING FINISH: Stainless steel #4 (hairline)
455	VENTILATION: Cross flow fan
456	HAND RAILS: handrails on rear car panels
457	FLOORING: Vinyl
458	CAR DOOR FINISH: Stainless steel #4 (hairline)
459	LANDING DOOR FINISH: Stainless steel #4 (hairline)
460	FIRE RATED DOORS: Fire rating - 60mins
461	PIT DEPTH: 1350
462	OVERHEAD: 4500
463	HOISTWAY DIMENSIONS (W x D)mm: 1600mm W x 1400mm D
464	CAR DIMENSIONS (W x D x H)mm: 1000mm W x 1100mm D x 2100mm D
465	CAR & HOISTWAY DOOR TYPE: Central opening (CO) doors.
466	DOOR OPENING(W x H x - mm): 700 mmW x 2000 mm H
467	DOOR OPERATOR: DC Door Operator
468	COP: Black Titanium Hairline
469	CAR POSITION INDICATOR: 7Segment
470	HALL FIXTURES
471	HALL FIXTURES FACE PLATE: SS Hairline
472	HALL BUTTON ARRANGEMENT:Hall Botton with HPI
473	STANARD FEATURES : Anti Nuisance Car Call Protection
474	Overload Device
475	Nudging
476	Grounding Switch
477	Emergency Car Light Unit
478	Infrated Curtain Door Protection
479	Door Time Protection
480	Emergency Alarm Button
481	Extra Door Time of Lobby & Parking
482	Door Open / Close Button
483	Manual Rescue Operation
484	Belt Inspection Drive
485	Auto Fan Cut Off
486	Automatic Rescue Operation
487	OPTIONS INCLUDES: Automatic Rescue Operation Total in Figures 0.0 0.0 Zero Only 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only ESMP Cost
488	Airt Quality Monitoring
489	Water Quality Monitoring
490	Noise Levels Monitoring
491	SOLID WASTE, Demolition wastes and scrapdisposal as per C & D rules 2016
492	Dust settling and removal of water after rains:Provision for dust settling measures including water spraying and installation of dust screens around the site.
493	8 drinking water purifiers (4 each at construction site andconstruction camps)100 LPH RO + UVwater filter-
494	Doctor’s visit to Construction Camp every fortnight forchecking of basic health of the workers.
495	Provision for helmet, gumboots, jackets, goggles, N95masks, Sanitisers, etc. to labourers. Lump sum
496	Bio Toilets in Construction CampSupply of D.R.D.O Technology Bio-Digester tanks Rotamoldeddouble wall manufactured in automatic Rotamoldingmachines using superior grade Virgin LLDPE(Polymer) with 2.5% Carbon Black, UV Resistant Polymerleading to highest quality consistency. Thickness of theouter shell of minimum 6mm, partitions made from HDPEPolymer of 8mm thick. Immobilization Matrices of HeavyDuty Poly Grass PVC Matting lining along the partitions onboth sides. Heavy duty pipes & fitting shall be used in these tanks of Finolex or equivalent make. Fasteners made ofBrass shall be used inside the tank with manufacturer’s testcertificate and including AMI (Bacteria) of 600 liters pertank.Size of Tank: 2000 Litres capacity upto 20-30 users per day;Tank Diameter of 1425mm; Tank Height of 1600mm;Outlet pipe diameter 75mm; inlet pipe diameter 110mm.
497	FRP Toilet Cabin IWC (Ceramic Pan) type of size 1250mm X 915mm X 2400mm with ± 5% tolerance.
498	Plumber(Skilled)
499	Plumber(unskilled)
500	Drinking water 250 LPH RO Plant

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents

Also Visit

Tenders

Meghalaya Tenders

Services Tenders

Tour and Travel Services Tenders

Tour and Travel Agency Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Development Of Tourism Facilities At Wahkaliar(Overlooking Nohkalikai), Sohra, Meghalaya, North Garo Hills-Meghalaya

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Development Of Tourism Facilities At Wahkaliar(Overlooking Nohkalikai), Sohra, Meghalaya, North Garo Hills-Meghalaya

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us