Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Civil Work |
| 2 | Plumbing |
| 3 | Electrical |
| 4 | Fire Service |
| 5 | Earth work in excavation by manual/ mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 in in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 in and lift up to 1.5 in, as directed by Engineer-in-charge.ln all kind of soil |
| 6 | Earthwork in excavation by manual means up to a depth of 2m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary andremoval Of surplus earth with all lead and lifts as directed and specified for the following classification of soils.(a) All kinds of soil (ordinary soil/ hard soil/ dense soil) |
| 7 | Earthwork in excavation by mechanical means upto a depth 2m below the existing ground level for foundation trenches of foundations, footing of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.In all kinds of soil |
| 8 | Earthwork in filling(excluding rock)in trenches,plinth,sides of foundation etc in layers not exceeding 20cm thick including breaking of clods,consolidating each layer by ramming and watering,lead up to 50m and lift upto 1.5mWith available excavated earth |
| 9 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m.ln all kind of soil |
| 10 | Earthwork in excavation by Mechanical means up to a depth of 2 M below the existing ground level tor foundation, trenches Of foundations, footings Of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification Of soils.ln ordinary rock (soft rock/ medium rock/ hard shale) |
| 11 | Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.(b/i) Stone soling of 100mm |
| 12 | Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete(b/ii) Stone soling of 150mm |
| 13 | Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete(a/ii) Brick soling - 150mm |
| 14 | Sand filling in plinth in layers not exceeding 150 mm thick including breaking Of clods, consolidating by ramming and watering complete as directed (maximum depth 45 cm). |
| 15 | Plain cement concrete works in foundation bed for footing steps,walls,brick works etc.below plinth level as directed and specified including dewatering if necessary and curing complete(shuttering where necessary shall be measured and paid separately)In prop. 1:3:6 (1 cement: 3 coarse sand: 6 coarse agg. By volume using mixture machine) |
| 16 | Brick work in cement mortar with 1st class brick including racking out joints and curing completely in super structure above plinth level upto first floor level including dewatering if necessary as directed.In proportion 1:6 (1 cement:6 Sand) |
| 17 | Brick work with common burnt clay modular ls' class bricks in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1 :6 (1 cement: 6 coarse sand).b) Above plinth level |
| 18 | 15 mm thick cement plaster of mix.In cement mortar 1:4 |
| 19 | 20 mm cement plaster on the rough side of mix:(a)1 :4 (1 cement: 4 fine sand) |
| 20 | Providing and applying Plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 21 | Wall painting with acrylic emulsion pain of approved brand and manufacture to give an even shade:New work (two or more coats) |
| 22 | Providing regular stone masonry in retaining walls etc. with coursed, hammer dressed or blunt chisel dressed stones Of heavy section not less than 25x25x30 cm with proper key stone each not less than 25x25x75 cm long sct in cement mortar 1 :6 (1 cement: 6 sand) including filling Of trenches and providing of weep holes at 1.20 to 1.50 metres apart staggered. |
| 23 | Providing boulder or stone filling with boulders or stones 15 cm size, 60 cm wide behind the rctaining wall etc. complete as directed. |
| 24 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12(1cement:6 coarse sand :12graded stone aggregate 20mm nominal size)upto plinth level with .cement mortar 1:6 (1cement : 6 coarse sand) |
| 25 | SHUTTERING/FORMWORK Centering and shuttering including strutting,propping etc and removal of form for all heights complete and as directed by Engineer in charge Foundation, footings, bases of columns, etc. for mass concrete works(using steel) Slabs,roofs,landings,balconies and access platform, shelves (using steel) Lintels,beams,plinth beams,and cantilever beam Columns, pillars, piers, Abutments,posts & strut(using steel) Stairs/ spiral staircase, (excluding landings) (using timber) Edges of slabs and breaks in floors and walls(using timber) - Under 20cm wide |
| 26 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement: All works upto plinth level.M20 or 1:1/2:3 (1cement :1 1/2 coarse sand: 3graded stone aggregate 20mm nominal size) |
| 27 | Reinforced cement concrete work in walls(any thickness), including attached pilasters, buttresses, fillets,columns, pillars,posts and struts etc, above plinth level upto first floor level,excluding cost of centering, shuttering, finishing and reinforcement:M20 or 1:1/2:3 (1cement :1 1/2 coarse sand: 3graded stone aggregate 20mm nominal size) |
| 28 | Reinforced cement concrete works in beams,slabs,roofs having slope up to 150 ,landings,balconies, shelves, chajjas, lintels, bands ,plain window sills ,staircases and spiral stair cases above plinth level upto first floor level,excluding the cost of centering, shuttering, finishning and reinforcement.M20 or 1:1/2:3 (1cement :1 1/2 coarse sand: 3graded stone aggregate 20mm nominal size) |
| 29 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.a) All Works upto plinth level |
| 30 | Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservoir, sewage & water treatment plant, tunnels/ subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @ 0.80% (minimum) to the weight of cement content per cubic meter of concrete or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. |
| 31 | 18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): up to 300 mm width |
| 32 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:(a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to ls:875 part-Ill (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminium sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc„ structural and weather silicone sealants, flashings, fire stop (barrier)-Gum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equaljsation & drainage and protection against fire hazard including. |
| 33 | Providing and fixing factory-made uPVC white colour sliding glazed window above 1.50 m in height, comprising uPVC multi-chambered frame with inbuilt roller track and sash extruded profiles, duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel sections made from roll-forming process of required length, shape and size as per uPVC profile. The window shall include uPVC extruded glazing beads of appropriate dimensions, uPVC extruded interlocks and uPVC extruded inline sash adaptor wherever required, EPDM gasket, wool pile, zinc alloy white powder-coated handle fixed on one side of the extreme panel, zinc-plated mild steel multi-point locking system with transmission gear and keeps, zinc alloy white powder-coated touch lock with hook where required for wire mesh panel, stainless steel (SS 304 grade) body adjustable double nylon rollers with weight-bearing capacity of 120 kg, G.I. fasteners of size 100 × 8 mm for fixing the frame to finished wall, and necessary stainless steel screws complete. The frame and sash shall be mitre-cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water. After fixing, the gap between frame and adjacent finished wall shall be filled with approved quality weather-proof silicone sealant over backer rod of required size, complete in all respects as per approved drawings and directions of the Engineer-in-Charge. Single or double glass panes shall be paid separately. |
| 34 | B) Two track four panels sliding window made of (big series) frame 67x50 mm & sash 46x62 mm both having wall thickness of 2.3 ±0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 4.00 sqm up to 8.00 sqm). |
| 35 | Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ±0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) crescent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicone sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/ double glass panes shall be paid separately). |
| 36 | a) Two track two panels sliding door made of (big series) frame 67x50 mm & sash 46x82 mm both having wall thickness of 2.3 ±0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm up to 5.00 sqm). |
| 37 | b) Two track four panels sliding door made of (big series) frame 67x50 mm & sash 46x82 mm both having wall thickness of 2.3 ±0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 8.00 sqm up to 10.00 sqm). |
| 38 | c) Three track three panels sliding door made of (big series) frame 116x45 mm & sash 46x82 mm both having wall thickness of 2.3 ±0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 5.00 sqm). |
| 39 | Providing and fixing factory made UPVC white colour fixed glazed windows/ ventilators comprising Of UPVC multichambered frame and mullion (wherever required) extruded profiles duly reinforced with 1.60 ±D.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100x8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/ double glass panes shall be paid separately). |
| 40 | Providing wood work in frames Of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.With 1st class local wood (i) pooma/hollock |
| 41 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core Of block board construction with frame of 1 St class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 42 | Providing and fixing bright finished brass loo mm mortise latch and lock with 6 levers and a pair of lever handles ofapproved quality with necessary screws etc. complete. |
| 43 | Extra for providing lsI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished Of requiredsize with necessary screws. (Shutter area to be measured). |
| 44 | Providing and fixing factory made PVC door frame of size 50 mm x 47 mm with a wall thickness of 5 mm ± 0.2 mm, made out of extruded PVC profile, mitred at corners and jointed with 2 Nos. of PVC brackets of size 190 mm x 100 mm, MS tube of size 19 mm x 19 mm x 1 mm, EPDM rubber gasket, PVC solvent cement, fixed to wall using anchor fasteners and screws at spacing of 200 mm, complete as per manufacturer’s specification and direction of Engineer-in-charge. |
| 45 | Providing and fixing 37 mm thick factory made PVC door shutter consisting of style and rails made of PVC hollow sectionof size 100 mm x 37 mm with wall thickness 2.0 mm ± 0.2 mm. The stiles and rails shall be mitre cut and joint with plastic brackets of size 75 mm x 220 mm at the corners and stainless steel screws. The stiles and rails shall be reinforced with M.S. tube of size 28 mm x 30 mm x 1.2 mm thickness, fitting inside the hollow section. The lock rail shall be of the size 100 mm x 37 mm. The paneling shall be of PVC sheet of 100 mm x 20 mm size. The paneling shall be fixed using snap-fit PVC beading of size 10 mm x 30 mm. The shutter shall be fixed to the frame using three nos. of stainless steel hinges and two nos. of 6 mm dia. tie bar fixed with nuts and washers. All complete as per manufacturer's specification and direction of the Engineer-in-charge. |
| 46 | Finishing with Deluxe Multi Surface Paint system for interiors and exteriors using primer as per manufacturers specifications, including scaffolding:Painting wood work with deluxe Multi Surface Paint to give an even shade. Two or more coats applied @ 0.90 ltr/10 sqm over and under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture. |
| 47 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:c) Marwat Slab |
| 48 | Providing Vitrified Antiskid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.Premium Range |
| 49 | Providing and laying matt finished vitrified tile of size 300x300x9.8 mm having water absorption less than 0.5°/a and conforming to ls:15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments ctc. complete as per direction of Engineer in-Charge. |
| 50 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls, skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Premium Range |
| 51 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to ls:15477,in average 6 mm thickness, including grouting of joints (Payment for groiiting of joints to be made separately).(b) Premium range |
| 52 | Grouting thejoints offlooring tiles having joints of3 mm width, using epoxy grout mix of 0.70 kg Of organic coated filler ofdesired shade (0.10 kg of hardener and 0.20 kg Of resin per kg), including filling, grouting and finishing complete as per direction Of Engineer-in-charge. |
| 53 | Providing and fixing hard drawn steel wire fabric of size 75x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-in-charge. |
| 54 | Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area Of opening tor panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. (a) Marine plywood conforming to ls:710 |
| 55 | Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to ls:2046 Type S, including cost Of adhesive Of approved quality.(a) 1.5mm thick |
| 56 | Supplying, fitting and fixing in position reinforcement bars upto first floor level, conforming to relevant I.S. code for RCC work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and bending with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurements for the same is required) Thermo-Mechanically Treated bars |
| 57 | Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ a.a. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)High Yield Strength Deformed bars or Tor Bars |
| 58 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc„ including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 59 | Finishing with Deluxe Multi Surface Paint system for interiors and exteriors using primer as per manufacturers specifications, including scaffolding:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqmover an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 60 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered). |
| 61 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required diameter and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and panelling to be paid for separately): |
| 62 | Providing and fixing glazing in aluminium door, window ventilator , shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:(e ) With float glass panes Of 8 mm thickness (weight not less than 20 kg/sqm) |
| 63 | Supplying and fixing C.I. cover without frame for manholes:(b) 500 mm diameter c.I. cover (medium duty) the weight of the cover to be not less than 58 kg |
| 64 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality(a/i)Pectangular shape 600x450 mm internal dimensions |
| 65 | Providing and fixing soil, waste and vent pipes:© 560 mm diameter c.I. cover (heavy duty) the weight of the cover to be not less than 108 kg(i) Sand cast iron S&S pipe as per IS:1729 |
| 66 | Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet the requirements of Tables 300.1 and 300.2 for subgrade construction as per Technical Specification Clause 303.5.2.Compacting original ground supporting subgrade |
| 67 | Construction of granular sub – base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.(A) By mix in place method(ii) For Grading II materials |
| 68 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80-100 kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc. as per Tables 400.11 & 400.12 and Technical Specification Clause 406. By Mechanical Means with 1 km lead. - WMM |
| 69 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90 - 1.20 kg/sqm using mechanical means as per Technical Specification clause 502. PRIME COAT(ii) Medium porosity |
| 70 | (iv) Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.30 to 0.35 kg/sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with hydraulic broom as per Technical Specification Clause 503. (iv) TACK COAT WITH BITUMIN EMULSION |
| 71 | 20 mm Thick Open-Graded Premix Carpet using Bitumen EmulsionProviding, laying and rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to require line, grade and level to serve as wearing coarse on a previously prepared base, including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either type A or Type B or Type C as per Technical Specification Clause 508.2. |
| 72 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Seal Coat Type-AA. By manual meanswithout Anti Stripping Agent(i) Bitumen 80/100 grade |
| 73 | Loading and Unloading of Lime, Aggregates, Stone Boulder, Brick Aggregates, Kankar, Building Rubbish, Crushed Slag, Stone for Masonry Work etc. by Mechanical Means.(i) Loading of Lime, Aggregates, Stone boulder, Brick Aggregates, Building Rubbish, Crushed Slag, Stone for Masonry Work by mechanical means including a lead upto 30 m. LOADING(A) Stone Aggregates (i)Grading II materials & (ii) WMM Aggregate UNLOADING(A) Stone Aggregates (i)Grading II materials & (ii) WMM Aggregate |
| 74 | Cost of Haulage of stones,Boulders and Sand excluding loading and unloadingA) STONE/AGGREGATES: Quarry at 10th km from siteAverage Lead = 10 km (surface=9.9km Kutcha track= 0.1km) |
| 75 | Providing & Fixing Glass panes 6mm thick for uPVC sliding door & Windows |
| 76 | Supply and placing of 2-Seater Reception Sofa |
| 77 | Supply and placing of counter table |
| 78 | Supply and placing of Featherlite Contact Medium Back Mesh Chair with Single Lock Synchro Mechanism & Adjustable Lumbar Support(Black) |
| 79 | Supply and placing of Ouch Cart Mellville Vegan Leather Corner Sofa Chaise |
| 80 | Supply and placing of Ouch Cart GLASS NORDIC NESTING COFFEE TABLE SET OF 2 |
| 81 | Supply and placing of Ouch Cart King size Ammerman Tufted Low Profile Platform Bed with Side tables |
| 82 | Supply and placing of Ouch Cart Alaska Wardrobe |
| 83 | Supply and placing of Ouch cart TEAK WOOD & RATTAN TV UNIT NATURAL |
| 84 | Supply and placing of OUCH Cart Joel Mid-Century Modern Walnut Office Desk Wooden Writing Desk with 2 Drawers in Gold |
| 85 | Supply and placing of OUCH Cart runge arm chair |
| 86 | Providing and fixing Indoor false ceiling using PVC board, including all materials, labour, channel framing, transportation, and installation charges, executed as per site conditionsThis is a non-SOR item and is derived based on actual rate analysis. |
| 87 | Providing and fixing floor mounted, white vitreous china single piece, double traps siphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions Of Engineer-in-Charge. |
| 88 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively, with automatic flushing cistern, standard flush pipe, C.P. brass spreaders with brass unions and G.I clamps, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. Flange of three urinal basins with 10 litre P.V.C. cistern |
| 89 | Providing and fixing wash basin with C.I. brackets, 15 mm dia. CP Brass single hole basin mixer Of approved quality and make, including painting Of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 90 | Providing and fixing 8 mm dia. C.P/ S.S Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. Of quality and make as approved by Engineer-in-charge. |
| 91 | Providing and fixing PTMT Waste Coupling for wash basin and sink, Of approved quality and colour. |
| 92 | Providing and fixing CP brass 32 mm size Bottle Trap of approved quality and make and as per the direction of Engineer-in-charge. |
| 93 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 94 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 95 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gins. |
| 96 | Providing and fixing PTMT grating of approved quality and colour. |
| 97 | Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the innerhinged round grating |
| 98 | Providing and fixing toilet paper holderC.P. brass |
| 99 | Providing and fixing mirror of superior glass and of required shape and size with plastic moulded frame of approvedmake and shade with 6 mm thick hard board backing:Rectangular shape 432x357 mm |
| 100 | Providing and fixing soil, waste and vent pipes: 100 mm diameter - Sand cast iron S&S pipe as per IS:1729 75 mm diameter - Sand cast iron S&S pipe as per IS:1729 |
| 101 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Enginner-in- Charge. Concealed work, including cutting chases and making good the walls etc. 15mm nominal outer diameter pipes 25mm nominal outer diameter pipes |
| 102 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points Of approved quality conforming to ls:8931 15 mm nominal bore |
| 103 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete with sand cast iron S&S as per IS:1729 Soil pipe (110mm dia) Waste water pipe (75mm dia) CPVC pipe (15mm dia) |
| 104 | Providing and fixing CP brass stop cock (Concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore |
| 105 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to ls standards and weighing not less than 810 gins 15 mm nominal bore |
| 106 | Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore 20 mm nominal bore |
| 107 | Providing and placing of polyethylene water storage tank, IS:12701with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 108 | 2.0 EXTERNAL WORK |
| 109 | Concealed wiring in looping system with 2x1.5 sqmm PVC isulated single core cable of 600V grade in heavy guage PVC pipe including occuping and fitting of elbows, bend, fees, junction boxes etc including required size of MS concealed Boxes and front plate for housing of switches, sockets, fan regulator, bell push etc complete to light point. Long Point upto 10 mts |
| 110 | Wiring as in item No.20 above to Light Plug Point when fixed else where with continuous earth wire complete. Long Point wiring upto 10 mts |
| 111 | Wiring as in item No.20 above to Wall point. Long Point wiring upto 10 mts |
| 112 | Supplying & fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB's for AC Application till 63A Double pole 415 V - 40-63 Amp |
| 113 | Supplying fitting and fixing DX3 Isolators for AC applications upto 125 A Double pole 240 V - 63 Amp |
| 114 | Supplying, fitting & fixing of Distribution Board Duo box With transparent crystal door 1 way 12 Module |
| 115 | Supplying fitting & fixing earthing with copper earth plate 600x600mmx6mm thick including accessories & providing masonary enclosure with cover plate having locking arrangement & watering pipe with charcoal, salts etc complete as required. Copper Earth Plate Electrode |
| 116 | Supplying, fitting and fixing of 75W Solar Street Light , 25W 2 in 1 Luminary (Lithium Ion Battery), 75W Solar Panel, G.I. Pole (20 Feet Galvanised Complete with Structure Automatic Dusk to Dawn) Complete. |
| 117 | Supplying fitting and fixing of FLOOD LIGHT surface or wall mounted with all necessary accessories Flood light suitable for highlighting architectural facade and general purpose lighting. - 150W |
| 118 | Supplying fitting and fixing of LANDSCAPE LIGHTS surface or wall mounted with all necessary accessories. Post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source. 15W Suitable for pole dia 50mm |
| 119 | Aesthetically designed aluminium landscape luminaire for diffused lighting with high power LED as light source 8W |
| 120 | Decorative rectangular shaped wall recessed luminaire with SMD LED as light source 7W INTERNAL WORK |
| 121 | Concealed wiring in looping system with 2x1.5 sqmm PVC isulated single core cable of 600V grade in heavy guage PVC pipe including occuping and fitting of elbows, bend, fees, junction boxes etc including required size of MS concealed Boxes and front plate for housing of switches, sockets, fan regulator, bell push etc complete to light point. Long Point upto 10 mts |
| 122 | Wiring as in item No.20 above to Light Plug Point when fixed else where with continuous earth wire complete. Long Point wiring upto 10 mts |
| 123 | Wiring as in item No.20 above to Wall point. Long Point wiring upto 10 mts |
| 124 | Supplying & fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB's for AC Application till 63ASingle pole 240/410 V - 40-63 Amp |
| 125 | Supplying fitting and fixing DX3 Isolators for AC applications upto 125 Adouble pole 240 V - 63 Amp |
| 126 | Supplying, fitting & fixing of Distribution Board Duo boxWith transparent crystal door - 1 way 6 Module |
| 127 | Supplying fitting and fixing of LED DOWNLIGHTS surface or wall mounted will all necessary accessories.18W |
| 128 | Supplying fitting & fixing earthing with copper earth plate 600x600mmx6mm thick including accessories & providing masonary enclosure with cover plate having locking arrangement & watering pipe with charcoal, salts etc complete as required. Copper Earth Plate Electrode |
| 129 | Supplying fitting & fixing of Water Heater (Geyser) of 1.5Kw/3Kw with pressure release valve including all necessary accessories as required - 35 litre capacity |
| 130 | Supply and placing of Philips 9W Blade Wall light Warm White |
| 131 | 2.0 INTERNAL & EXTERNAL WORK |
| 132 | Addressable Fire Alarm and Conventional Fire Alarm Detection System as per Assam P.W.D. Analysis Building (Electrical). Supply of intelligent, addressable twin angle optical smoke cum thermal heat - multisensor detectors (complete assembly) with inbuilt microprocessor, memory and decision algorithm, CPU failure mode, status indicator, with in built fault loop isolator and standard detector base with NO DIP/ ROTARY or Mechanical address switch but soft programmable.or alternatively Laser type spot multisensing detector. |
| 133 | Supplying & Fixing of ABC DRY POWDER Fire Extinguisher including with all necessary accessories.. Supplying Installation fixing ABC DRY CHEMICAL POWDER Fire Extinguisher of 10 Kg trolley mounted confirming to IS: 2171 and CO₂ Cartridge confirming to IS: 4947, Powder Confirming to IS: 4308. PUMP |
| 134 | Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required:(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.(b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-‘F’ insulation, conforming to IS-325.(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Suitable cement concrete foundation duly plastered with anti vibration pads. 2850 lpm at 70 m Head |
| 135 | Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads 2850 lpm at 70 m Head |
| 136 | Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.Suitable HP squirrell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-F insulation, conforming to IS : 325.M.S fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 lpm at 70 m Head CONTROL PANEL |
| 137 | Fabrication, supply, Installation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming & Outgoings, suitable for operation on 415V, 3 phase, 50Hz AC supply with enclosure protection class IP 42 as required: Supply, installation, testing and commissioning of Main Fire Pump Control Panel suitable for 75 HP Fire Pump, comprising 200 A, 50 kA TPN MCCB with Ics=100%....\\"Jockey Pump Panel with 100 A, 50 kA TPN MCCB, Ics=100% Icu, ....& Diesel engine control with automatic manual selector switch etc... Pipes and accessories |
| 138 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm dia - Main Pipe 65mm dia - Branching Pipe |
| 139 | Supplying fixing Single headed internal yard hydrant valve with instantaneous Gunmetal Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required Single headed stainless steel |
| 140 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.\\" Stainless steel (Grade 304) |
| 141 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc conforming to IS 636 (Type-A) as required Stainless steel (Grade 304) |
| 142 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in open office rot, conforming to IS 584 complete with the following as required to run nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 1258520 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipments on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m |
| 143 | Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed stainless steel |
| 144 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm², complete as required. |
| 145 | Providing, installation, testing and commissioning of non-return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required: 100mm dia |
| 146 | Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required 100 mm dia |
| 147 | Butterfly valve PN 1.6 rating 100mm dia butterfly valve |
| 148 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required\\" 100mm dia |
| 149 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories: Pendent Sprinkler |
| 150 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required Stainless steel (Grade 304) |
| 151 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe c onnection conforming to IS 904 as required: 2 way - 100 mm dia M.S. Pipe |
| 152 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required |
| 153 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 154 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required 100 mm dia |
| 155 | 2.0 Environmental Monitoring |
| 156 | Air Quality Monitoring |
| 157 | Water Quality Monitoring |
| 158 | Noise Monitoring |
| 159 | Doctor’s visit to Construction Camp every fortnight for checking of basic health of the workers. |
| 160 | Provision for helmet, gumboots, jackets, goggles, N95 masks, Sanitisers, etc. to labourers. Lump sum |
| 161 | Bio Toilets in Construction Camp Supply of D.R.D.O Technology Bio-Digester tanks Rota-molded double wall manufactured in automatic Rota-molding machines using superior grade Virgin LLDPE (Polymer) with 2.5% Carbon Black, UV Resistant Polymer leading to highest quality consistency. Thickness of the outer shell of minimum 6mm, partitions made from HDPE Polymer of 8mm thick. Immobilization Matrices of Heavy Duty Poly Grass PVC Matting lining along the partitions on both sides. Heavy duty pipes & fitting shall be used in these tanks of Finolex or equivalent make. Fasteners made of Brass shall be used inside the tank with manufacturer’s test certificate and including AMI (Bacteria) of 600 liters per tank.Size of Tank: 2000 Litres capacity upto 20-30 users per day; Tank Diameter of 1425mm; Tank Height of 1600mm; Outlet pipe diameter 75mm; inlet pipe diameter 110mm. |
| 162 | FRP Toilet Cabin IWC (Ceramic Pan) type of size 1250mm X 915mm X 2400mm with ± 5% tolerance. |
| 163 | Installation Charges i) Plumber (Skilled) ii) Plumber (Unskilled) Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
