Tender For Proposed Upgradation Of Tourism Amenities At The Umiam Water Sports Complex (Block-A) At Umiam, Meghalaya, And Proposed Redevelopment Of Orchid Lake Hospitality Complex (Block-B) At Umiam, Meghalaya., Umiam-Meghalaya

TDR : 54754933

Tender Notice
BOQ

11 Days Left

Umiam , Meghalaya

Tender Brief : Tender For Proposed Upgradation Of Tourism Amenities At The Umiam Water Sports Complex (Block-A) At Umiam, Meghalaya, And Proposed Redevelopment Of Orchid Lake Hospitality Complex (Block-B) At Umiam, Meghalaya.

Document Fees
₹ 22700 /-

EMD
₹ 6834000.0 /-

Tender Value
₹ 22.78 Crore /-

Submission Date
02-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	BLOCK -A :-
2	Civil Works
3	Plumnbing Works
4	Electrical Works
5	BLOCK -B :-
6	Civil Works
7	Plumnbing Works
8	Electrical Works
9	Fire Work
10	Earthwork
11	Earthwork in excavation by manual means upto a depth 2m below the existing ground level for foundation trenches of foundations, footing of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.
12	In all kinds of soil
13	Extra over item no. 2.1 and 2.2 above for each 1m depth or part thereof beyond the initial depth of 2 m.
14	Earthwork in filling(excluding rock)in trenches,plinth,sides of foundation etc in layers not exceeding 20cm thick including breaking of clods, consolidating each layer by ramming and watering,lead up to 50m and lift upto 1.5m
15	With available excavated earth
16	Sub Head : Random Rubble Masonry With Cement Mortar
17	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12(1cement:6 coarse sand :12graded stone aggregate 20mm nominal size)upto plinth level with .
18	Cement mortar 1:6 (1cement : 6 coarse sand)
19	Providing regular stone masonry in retaining walls etc. with coursed, hammer dressed or blunt chisel dressed stones Of heavy section not less than 25x25x30 cm with proper key stone each not less than 25x25x75 cm long sct in cement mortar 1 :6 (1 cement: 6 sand) including filling Of trenches and providing of weep holes at 1.20 to 1.50 metres apart staggered.
20	Providing boulder or stone filling with boulders or stones 15 cm size, 60 cm wide behind the rctaining wall etc. complete as directed.
21	Sub Head : Stone Soiling
22	Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.
23	Stone soiling
24	100mm
25	150 mm
26	Sub Head : Cement Concrete Works
27	Plain cement concrete floor base in prop 1 :3:6 laid in alternate bays as specified with coarse aggregate Of size 13 mm to 32 mm including dewatering if necessary, and curing etc. complete.
28	100 mm thick in prop 1:3:6
29	Plain cement concrete works in foundation bed for footing steps,walls,brick works etc.below plinth level as directed and specified including dewatering if necessary and curing complete(shuttering where necessary shall be measured and paid separately)
30	In prop. 1:3:6 (1 cement: 3 coarse sand: 6 coarse agg. By volume using mixture machine)
31	Sub Head : Shuttering
32	SHUTTERING/FORMWORK Centering and shuttering including strutting,propping etc and removal of form for all heights complete and as directed by Engineer in charge
33	Foundation, footings, bases of columns, etc. for mass concrete works(using steel)
34	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc (using steel)
35	Slabs,roofs,landings,balconies and access platform, shelves (using steel)
36	Lintels,beams,plinth beams,girders, bressumers and cantilever(using steel)
37	Columns, pillars, piers, Abutments,posts & strut(using steel)
38	Stairs/spiral staircase, (excluding landings) (using timber)
39	Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards (using timber).
40	Edges of slabs and breaks in floors and walls(using timber)
41	Sub Head : RCC Work
42	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuterring, finishing and reinforcement. All work upto plinth level
43	M20 or 1:1 1/2:3 (1cement :1 1/2 coarse sand:3graded stone aggregate 20mm nominal size
44	Reinforced cement concrete works in beams,slabs,roofs having slope up to 150 ,landings, balconies, shelves, chajjas,lintels,bands,plain window sills,staircases and spiral stair cases above plinth level upto first floor level,excluding the cost of centering,shuttering,finishning and reinforcement.
45	M20 or 1:1/2:3 (1cement :1 1/2 coarse sand: 3 graded stone aggregate 20mm nominal size)
46	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, fillets, columns, pillars, posts and struts etc. above plinth level up to first floor level, excluding cost of centering, shuttering, finishing and reinforcement:
47	M20 or 1 :11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
48	Extra over item No 6.2 to 6.8 above for each subsequent floor or part thereof above the first floor level.
49	Sub Head : Brick Work
50	Brick work in cement mortar with 1st class brick including racking out joints and curing completely in super structure above plinth level upto first floor level including dewatering if necessary as directed.
51	In proportion 1:6 (1 cement:6 Sand)
52	Extra over item No 7.3 above for each subsequent floor or part thereof above the first floor level.
53	Sub Head : Plastering
54	20 mm cement plaster of mix:
55	In cement mortar 1:4
56	Sub Head : FLooring And Finishing Works
57	Filling sunken floor with broken bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels
58	Brick Bats
59	Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size ), reinforced with 1.6 mm dia. mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.
60	50 mm thick
61	Cement concrcte floor topping 1:1:2 (1 cement: 1 coarse sand: 2 stone aggregate) finished with a floating coat of neat cement, including cement slurry, complete
62	Cement plaster skirting up to 30 cm height, with cement mortar 1 :3 (1 cement: 3 coarse sand), finished with a floating coat of neat cement.
63	Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations Of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish ctc. complete at all levels.
64	Granite of any colour and shade
65	Area of slab up to 0.50 sqm
66	Stone tile (polished) work for wall lining over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.
67	Granite of any colour and shade
68	Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to ls:15477, in average 6 mm thickness, including grouting of joints (Payment for groiiting of joints to be made separately).
69	Deluxe range
70	Providing Vitrified Antiskid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.
71	Deluxe range
72	Providing polished VITRlFIED wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.
73	Deluxe range
74	Providing exterior wall cladding with flagstones Of 25mm average thickness on 20 mm thick plaster 1 :3 (1 cement: 3 coarse sand) and jointed with grey cement slurry complete as directed.
75	Sub Head : Water Proofing
76	Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:Providing and laying water proofing treatment in sunken portion of WCs,bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. (b) 2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air ciire for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing Of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
77	Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:
78	(a) After surface preparation 1st layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound @0.253 kg/sqm.(b) Laying 2nd layer of Fibre glass cloth when the lst layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) 3rd layer of 1.5'mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around.(d) 4th and final layer Of brick tiling with cement mortar (which will be paid for separately).For the purpose of measurement the entire treated surface will be measured.
79	Sub Head : STRUCTURAL STEEL AND ALLIED WORK
80	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
81	Structural steel work in single section,fixed with connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete
82	Supplying, fitting and fixing in position reinforcement bars upto first floor level, conforming to relevant I.S. code for RCC work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and bending with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurements for the same is required)
83	Thermo-Mechanically Treated bars
84	Sub Head : ROOFING
85	Providing and fixing pre-coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 meter or as desired by Engineer-in-charge. The sheet shall be fixed using self-drilling/ self-tapping screws of size (5.5x55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
86	Providing and fixing pro-coated galvanised steel sheet rcofing accessories 0.50 mm (+0.05 a/a) total coated thickness, Zinc coating 120 grams per sqm as per ls:277, in 240 Mpa Steel grade, 5-7microns epoxy primer on both side Of the sheet and polyester top coat 15-18 microns using self-drilling/ self tapping screws complete:
87	Ridges plain
88	Flashings/ Aprons.( Up to 600 mm)
89	Barge board (up to 300 mm)
90	Gutter (600 mm over all girth)
91	Sub Head : CEILING WORK
92	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge,
93	Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Flockwool conforming to ls:8183,density 48 kg/cum, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling Of building.
94	Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in ti.ue horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and Of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre andcross 'T' Of size 24x25 mm made of 0.30 mm thick (minimum) sheet,1200 mm long spaced between main \\"T\\" at 600 mm centre to centre to form a grid of 1200x600 mm and Secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids Of 600x600 mm and wall angle of size 24x24xO.3 mm and laying false ceiling tiles of approved textui.e in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using Gl slotted cleats of size 27x37x25xl,6 mm fixed to ceiling with 12.5 mm dja. and 50 mm long dash fasteners, 4 mm Gl adjustable rods with galvanised butterfly level clips of size 85x30xO.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-incharge.
95	12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per ls:2095 part I and laminated with white 0,16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit
96	Providing and fixing wall panels and false ceiling with SVP-06 FRONTO SLATE PANELS OF SUITABLE SHADE (VOX make/equivalent) with accessories of same shade, including framing cost with GI channel of suitable make (Saint Gobain / Tata Agrico or equivalent), complete in all respects, inclusive of installation charges, transportation, and applicable GST, all complete as per drawings and as directed by the Architect and Engineer-in-Charge. (quotation attached- material to be procured from KREATIVE INFINITY) [RATE: ₹ 537.00 PER SQFT]
97	Providing and fixing false ceiling with Soffit Infratop (VOX make/equivalent) with accessories of same shade, including framing cost with GI channel of suitable make (Saint Gobain / Tata Agrico or equivalent), complete in all respects, inclusive of installation charges, transportation, and applicable GST, all complete as per drawings and as directed by the Architect and Engineer-in-Charge. (quotation attached- material to be procured from KREATIVE INFINITY) [RATE: ₹ 465.00 PER SQFT]
98	Providing and fixing wall-to-wall shower enclosure (JAQUAR - DELTA make or equivalent) comprisingCorner entry half round shower enclosure with curved sliding door, made of 6mm thick clear/tinted toughened glass, with aluminium/steel profile in Chrome / Black / Gold finish, including all necessary fittings, fixtures, handles, rollers, gaskets, silicon sealant, complete as per manufacturer’s specification and as directed by the Architect and Engineer-in-Charge. (material to be procured from JAQUAR GROUP)
99	Sub Head : Door And Windows
100	Providing wood work in frames of doors, windows , clerestory windows and other frames,wrought, framed and fixed in position with hold fast lugs or with dash fasteners of required diameter and length.
101	Sal wood
102	Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core Of block board construction with frame of 1 St class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters
103	35 mm thick including lsl marked Stainless Steel butt hinges with necessary screws
104	Providing and fixing factory made UPVC white colour casement/ casement cum fixed glazed door comprising of UPVC multi-chambered frame, sash and mullion (wherever required) extruded profiles duly reinforced with 1.60 ±0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of fi.ame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling Of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be f illed with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/ double glass panes shall be paid separately).
105	Casement door with 3D hinges made Of (big series) frame 67x64 mm & sash 67xl 10 mm both having wall thickness of 2.3 sO.2 mm and single glazing bead/ double glazing bead of appropriate dimension.
106	Providing and fixing factory made UPVC white colour sliding glazed door comprising of ilpvc multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 cO.2 mm thick galvanized mild steel section made from roll forming pl.ocess of required length (shape & size according to UPVC profile), appropriate dimension UPVC extruded glazing beads, UPVC extruded interlock and UPVC extruded inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) crescent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage Of water etc. After {ixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and Of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/ double glass panes shall be paid separately).
107	Two track tour panels sliding door made of (big series) frame 67x50 mm & sash 46x82 mm both having wall thickness of 2.3 sO.2 mm and single glaring bead/ double glazing bead of appropriate dimension. (Area Of dcor above 8.00 sqm up to 10.00 sqm).
108	Providing and fixing factory made UPVC white colour casement windows/ ventilators comprising Of UPVC multichambered frame and mullion (wherever required) extruded profiles duly reinforced with 1.60 ±D.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100x8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/ double glass panes shall be paid separately).
109	Casement window double panels with S.S. friction hinges (300xl9xl.9 mm) made of (small series) frame 47x50 mm, sash 47x68 mm & mullion 47x68 mm all having wall thickness of 1.9 cO.2 mm and single glazing bead of appropriate dimension. (Area of window upto 0.75sqm ).
110	Casement window double panels with S.S. friction hinges (350xl9xl.9 mm) made of (big series) frame 67x60 mm & sash/ mullion 67x80 mm both having wall thickness of 2.3 ±D.2 mm and single glazing bead/ double glazing bead Of appropriate dimension. (Area of window above 1.50 sqm).
111	Providing and fixing factory made upvc white colour sliding glazed window above 1.50 in in height dimension comprising of UPVC multi-chambered frame with inlbuilt roller track and sash extruded profiles duly reinforced with 1.60 sO.2 mm thick galvanized mild steel section made from roll forming process Of required length (shape & size according to UPVC profile), appropriate dimension of UPVC extruded glazing beads, UPVC extruded interlocks and UPVC extruded inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (jf required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws ctc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage Of water eta. After fixing frame the gap bctween frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction Of Engineer-in- Charge. (Single/ double glass panes shall be paid separately).
112	Two track two panels sliding window made of (big series) frame 67x50 mm & sash 46x62 mm both having wall thickness Of 2.3 cO.2 mm and single glazing bead/ double glazing bead Of appropriate dimension.
113	Sub Head : Door,Windows And Ventilators Fittings
114	Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:
115	250mm x 10mm
116	Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws, eta. to suit shutter thickness complete.
117	Providing and fixing chromium plated brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved qiiality with necessary screws etc. complete.
118	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.
119	With float glass panes of 6 mm thickness (weight not less than 15.0 kg/sqm)
120	Sub Head : Painting, Oiling, Varnishing, Polishing Work
121	Providing and applying Plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
122	Finishing with Deluxe Multi Surface Paint system for interiors and exteriors using primer as per manufacturers specifications, including scaffolding:
123	Two or more coats applied on walls @ 1.25 Itr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr/10 Sqm
124	Painting wood work with deluxe Multi Surface Paint to give an even shade. Two or more coats applied @ 0.90 ltr/10 sqm over and under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture.
125	Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture
126	Sub Head : Rain Water Pipe
127	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.
128	110 mm diameter
129	Sub Head : Plinth Protection
130	Making Plinth Protection 50mm thick of cement Concrete1:3:6 (1 cement :3 coarse sand : 6 graded coarse agg.20mm nominal size)over 75mm thick bed of dry brick ballast 40mm nominal size,well rammed and consolidated and grouted with fine sand including necessary excavation, levelling and dressing & finishing the top smooth
131	Sub Head : Anti Termite
132	Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti -termite treatment(excluding the cost of chemical emulsion)
133	Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/Rm including drilling and plugging holes etc. with Chlorpyriphos / Lindane E.C.20% with 1% concentration
134	Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/Rm including drilling and plugging holes etc. with Chlorpyriphos / Lindane E.C.20% with 1% concentration
135	Treatment Of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 Coarse sand) to match the existing floor: With Chlorpyriphos/ Lindane E.C. 20% with 1 a/o concentration
136	Sub Head : Water Tanks
137	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ls:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
138	DRAINAGE
139	Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
140	100 mm diameter
141	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:
142	100 mm diameter S.W. pipe
143	Providing and fixing square-mouth S.W. gully trap grade 'A'’ complete with C.I. grating brick masonry chamber with water tight C.I. Cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :
144	100x100 mm size P type
145	With F.P.S. Bricks class designation 75
146	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
147	100 mm dia. R.C.C. pipe
148	150 mm dia. R.C.C. pipe
149	250 mm dia. R.C.C. pipe
150	300 mm dia. R.C.C. pipe
151	450 mm dia. R.C.C. pipe
152	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :
153	Inside size 90x80 cm and 45 cm deep including C.I. Cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
154	With F.P.S. bricks with class designation 75
155	Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :
156	With F.P.S. bricks class designation 75
157	Extra for depth for manholes
158	Size 90x80 cm
159	With F.P.S. bricks class designation 75
160	Size 120x90 cm
161	With F.P.S. bricks class designation 75
162	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design:
163	With 20 mm diameter round bar
164	Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand ) with pre-cast R.C.C. vertical grating complete as per standard design :
165	With F.P.S. Bricks
166	Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design :
167	With F.P.S. bricks
168	Sub Head : RAIN WATER HARVESTING TANK
169	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level
170	All type of soil
171	300 mm dia
172	Rocky strata including Boulders
173	300 mm dia
174	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.:
175	150 mm nominal size dia
176	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.:
177	150 mm nominal size dia
178	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
179	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
180	Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in- charge.
181	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
182	Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
183	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
184	150 mm dia
185	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
186	All kinds of soil
187	Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge.
188	Ordinary rock
189	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level
190	1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).
191	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
192	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
193	Centering and shuttering including strutting, propping etc. and removal of form for all heights
194	Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc
195	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
196	Cement mortar 1:4 (1 cement : 4 coarse sand)
197	FURNITURE
198	Providing and supplying sofa set of approved design and size, with high-density foam cushions, upholstered in approved fabric/leatherette, complete with wooden touch finish frame/ arms/ legs, including all accessories, transport, installation, and placing in position, all complete as per drawings and as directed by the Architect & Engineer-in-Charge.
199	Providing and placing centre table of approved design and finish, complete as per drawings and as directed by the Architect & Engineer-in-Charge.
200	Providing and placing side table of approved design and finish, made of 18 mm thick pre-laminated board on one or both sides with 2 mm thick edge banding, complete with all necessary fittings, fixtures, transport, installation and finishing, all complete as per drawings and as directed by the Architect & Engineer-in-Charge.
201	Providing and fixing Head Board with wall cladding of size 1220 mm × 2500 mm, made of 19 mm ply (12 mm back) with laminate finish, including integrated LED strip lights with all fittings and accessories, complete as per drawings and as directed by the Architect & Engineer-in-Charge.
202	Providing and placing Queen Size Bed of approved design, made of 19 mm thick plywood, with all exposed and internal surfaces finished with 1 mm thick laminate. Item to include necessary fittings, hardware, wooden lipping, beading and accessories, complete as per drawings and as directed by the Architect & Engineer-in-Charge.
203	Providing and placing Single Size Bed of approved design, made of 19 mm thick plywood, with all exposed and internal surfaces finished with 1 mm thick laminate. Item to include necessary fittings, hardware, wooden lipping, beading and accessories, complete as per drawings and as directed by the Architect & Engineer-in-Charge.
204	Providing and placing Bed Side Table with drawer, made of 19 mm ply (12 mm for back) with laminate finish, complete with all fittings and hardware as per drawings and as directed by the Architect & Engineer-in-Charge.
205	Providing and fixing in position Wardrobe, Table, TV Unit with minibar cabinet and luggage rack with storage, including 8 mm thick SS strips, PVC louvers and looking glass, as per approved design and drawings. Carcass to be made of 19 mm thick plywood for top, bottom, sides and shelves, 12 mm thick plywood for back, and 19 mm plywood/glass ledges for internal shelves. All exposed and internal surfaces shall be finished with laminate. Shutters shall be of 19 mm thick ply with 1 mm laminate. Drawer unit to be made of 19 mm thick ply for sides, bottom, back and front. Item shall include all necessary hardware, hinges, screws, sliding drawer fittings, shelf fittings, glass ledges, wooden lipping, beading, and all other fixtures, complete in all respects as per drawings and as directed by the Architect & Engineer-in-Charge.
206	Providing and installing Mini Bar of approved make (Godrej, Haier, or equivalent), complete with all accessories, fittings, electrical connections, and placing in position as per drawings and as directed by the Architect & Engineer-in-Charge.
207	Providing and installing 43-inch LED TV of approved make (Haier or equivalent), including all mounting accessories, wiring, connections, and placing in position as per drawings and as directed by the Architect & Engineer-in-Charge.
208	Providing and placing sofa set comprising two single-seater sofas with high-density foam cushions and one coffee table of approved design and finish, sofas made of solid/engineered wood frame, coffee table made of 19 mm thick plywood with laminate finish, complete with all necessary hardware, fittings, lipping, and accessories as per drawings and as directed by the Architect & Engineer-in-Charge.
209	Providing and placing verandah/balcony garden sitting set with table of approved design and finish, made of weather-resistant material, complete with all fittings and accessories as per drawings and as directed by the Architect & Engineer-in-Charge.
210	Providing and fixing housekeeping shelves made of 18 mm thick board pre-laminated on both sides with 2 mm thick edge banding, complete with all necessary fittings, fixtures, and installation as per approved drawings and as directed by the Architect & Engineer-in-Charge.
211	Providing and fixing locker of size 2000 mm × 2100 mm with individual lockers of 630 mm × 700 mm, made of 18 mm thick pre-laminated board on both sides with 2 mm thick edge banding, with shutters for each locker, complete with locks, handles, necessary fittings, and installation as per drawings and as directed by the Architect & Engineer-in-Charge
212	Providing and fixing vanity counter box made of 18 mm thick plywood, finished with 1 mm thick laminate on external surfaces and balancing laminate on internal surfaces, with 2 mm thick edge banding, complete with all necessary fittings, fixtures, and installation as per approved drawings and as directed by the Architect & Engineer-in-Charge.
213	Providing and placing study table chairs of approved design and finish, of Godrej or equivalent make, complete with all fittings and accessories as per drawings and as directed by the Architect & Engineer-in-Charge.
214	Providing and placing conference room chairs of approved design and finish, of Godrej or equivalent make, complete with all fittings and accessories as per drawings and as directed by the Architect & Engineer-in-Charge.
215	SANITARY:
216	Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete
217	Providing and fixing 15 mm dia C.P. Ablution health faucet with 1.0 m long SS extension pipe with wall hook and operating knob complete in all respects.
218	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required :
219	Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.
220	Extra for providing auto-flushing sensors operated by infra red sensors (Electrical operated) complete with fixing arrangement on wall in place of PVC automatic flushing cistern
221	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :
222	White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.
223	Extra for Single lever basin mixer (ceramic disk washerless fitting) C.P. single hole mixing fitting in place of 15 mm brass pillar taps
224	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :
225	Kitchen sink with drain board
226	510x1040 mm bowl depth 250mm.
227	Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
228	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
229	Semi rigid pipe
230	32 mm dia
231	40 mm dia
232	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :
233	Rectangular shape 1500x450 mm
234	Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
235	Providing and fixing toilet paper holder :
236	C.P. brass
237	Providing and fixing soil, waste and vent pipes :
238	100 mm dia.
239	Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905
240	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. :
241	For 100 mm dia. Pipe
242	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
243	100 mm
244	Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
245	Providing and fixing plain bend of required degree.
246	100 mm
247	Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
248	Providing and fixing heel rest sanitary bend
249	100 mm dia
250	Sand cast iron S&S as per IS - 1729
251	Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe
252	100 mm dia pipe,SS 304 grade coupling with EPDM rubber gasket
253	Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter :
254	100 mm
255	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
256	100 mm inlet and 100 mm outlet
257	Sand cast iron S&S as per IS: 3989.
258	Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work :
259	100 mm diameter pipe
260	Repainting sand cast iron/ centrifugally cast iron (spun) iron, soil, waste, vent pipes and fittings with paint of any colour such as chocolate, grey or buff etc :
261	100 mm diameter pipe
262	Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.
263	Waste coupling 31mm of 79mm length and 62mm breadth weighing not less than 45gms.
264	Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms.
265	Providing and fixing PTMT Bottle Trap for Wash basin and sink.
266	Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms.
267	Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms.
268	Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms.
269	Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour Weighing not less than 88 gms..
270	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.
271	600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than
272	Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour. Weighing not less than 300 gms.
273	Providing and fixing 15 mm dia C.P brass bib cock 2-in-1 (long Body) C.P. cast brass with wall flange [Quarter-turn washerless fitting]
274	Providing and fixing 15 mm dia C.P. angle valves( quarter turn, washer less) with SS mesh filter and C.P. cast brass wall flange
275	Providing and fixing 15 mm dia SS braided pipe 450mm long with connecting nuts [for connection toMixers & taps from angle valve]
276	Providing and fixing Cast bronze chrome plated grating with ring and Stainless steel anti cockroach basket and two SS screw including fixing to the floor with cement mortar. Size of coackroack trap shall be 125 mm dia
277	Providing and fixing Soap Disc.
278	Providing and fixing C.P shower fitting comprising of [All fixture of JAGUAR fittings]:- One overhead Multi flow shower with shower arm and wall flange, One Single liver Shower Mixer with four way divertor, One bath spout with wall flange including cutting and making good the walls where required. [JAGUAR CATLOUGE NO ].
279	WATER SUPPLY (INTERNAL AND EXTERNAL) INSTALLATION
280	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
281	Internal work - Exposed on wall
282	15 mm nominal outer dia Pipes
283	20 mm nominal outer dia Pipes
284	25 mm nominal outer dia Pipes
285	32 mm nominal outer dia Pipes
286	40 mm nominal outer dia Pipes
287	50 mm nominal outer dia Pipes
288	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
289	15 mm nominal outer dia Pipes
290	20 mm nominal outer dia Pipes
291	25 mm nominal outer dia Pipes
292	32 mm nominal outer dia Pipes
293	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
294	External work
295	15 mm nominal outer dia Pipes
296	20 mm nominal outer dia Pipes
297	25 mm nominal outer dia Pipes
298	32 mm nominal outer dia Pipes
299	40 mm nominal outer dia Pipes
300	50 mm nominal outer dia Pipes
301	65 mm nominal outer dia Pipes
302	80 mm nominal outer dia Pipes
303	100 mm nominal outer dia Pipes
304	150 mm nominal outer dia Pipes
305	BRASS FITTINGS
306	Providing and fixing brass bib cock of approved quality :
307	15 mm nominal bore
308	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
309	32 mm nominal bore.
310	40 mm nominal bore
311	50 mm nominal bore
312	65 mm nominal bore
313	80 mm nominal bore
314	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
315	15 mm nominal bore
316	20 mm nominal bore
317	25 mm nominal bore
318	Constructing masonry Chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :
319	With F.P.S. bricks
320	Constructing masonry Chamber 90x90x100 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :
321	With F.P.S. bricks
322	ELEVATOR
323	Primus MRL R25 (8 passengers)
324	Concealed Wiring using MS Condute pipe
325	Wiring in concealed with 2x 1.5Sqmm PVC insulated single core conductor of 600V grade in No.l6 Swg,. Heavy Gauge welded stove enameled painted, 20mm dia MS conduit pipe (E.T) including accessories such as bends,Tees, junctionl boxes, sockets, locknuts brass brushes, etc and required sizes of :MS Box and recommended front plate for housing switches, sockets, fan regulator bell push, etc, matching the colour of the surrounding wall, etc as required or as directed by the Engineer incharge or Architect including earthing Conduit.
326	Long Point wiring upto 10 mts
327	Wiring as in item No.29 complete to a Light Plug Point when fixed elsewhere with continuous earth wire.
328	Long Point wiring upto 10 mts
329	Wiring as in item No.29 above to Power Plug Point with 2x4mm2 including supplying and fitting of l5Amp modular switch. Socket Combined with continuous earth wire to a Power Plug Point Complete.
330	Long Point wiring upto 10 mts
331	Wiring as in item No.20 above to Ceiling Fan/exaust Fan Point.
332	Long Point wiring upto 10 mts
333	Wiring as in item No.20 above to Wall Light point.
334	Long Point wiring upto 10 mts
335	Wiring as in item No.20 above to Calling Bell/Bell Indicator Point
336	Long Point wiring upto 10 mts
337	Wiring as in item No.20 above for stair case/Two way switch Light Point Controlled by 2 Nos, 2Way 5Amp Switches
338	Long Point wiring upto 10 mts
339	Drawing of Main and Sub-Main Line wiring approved VIR or PVC cable 250 V Grade in Heavy Gauge 16 Swg E.T. Conduit Pipe with all necessary accessories.
340	With 2x2.5mm² copper conductors
341	Supplying & fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB's for AC Application till 63A
342	Single pole 240/410 V
343	6-32 Amp
344	Supplying fitting and fixing DX3 Isolators for AC applications upto 125 A
345	Four pole 415 V
346	63 Amp
347	Supplying, fitting & fixing of Distribution Board ETNP DB's for MCB, Isolator, RCCB and RCBO
348	IP 43 - #1K 09 with metal door
349	6 way 8+18 Module
350	IP 43 - #1K 09 with metal door
351	6 way 8+18 Module
352	IP 43 - #1K 09 with metal door
353	8 way 8+24 Module
354	IP 43 - #1K 09 with metal door
355	8 way 8+24 Module
356	Supplying fitting and fixing of LED DOWNLIGHTS surface or wall mounted will all necessary accessories.
357	round slim fir low profile downlights are engineered to deliver superior light output and uniformity utilising the latest edge lit LED technology
358	18W ceiling cutout dia 210mm height 16mm
359	Supplying fitting and fixing complete polish brass bracket, 16mm dia and 23cm long with cast backplate and brass lamp holder with LED bulb surface or wall mounted with all necessary accessories
360	Supplying fitting and fixing of WEATHER PROOF LED surface mounting luminaire with PC housing in opal finish suitable for wet location with all necessary accessories.
361	Supplying and Fitting of ceiling fan AC operated type 220/250 volt. Complete with 3 Nos of blades down rod canopy hanging shackel & 30mm length of down rod supplied with the fan by the dealer but the extra length will be charged @ Rs 25.00/mtrs.
362	AC ceiling Fan '1200' mm sweeps
363	Supplying , fitting and fixing of exhaust fan double bearing self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts and other petty accessories as required.
364	Domestic exaust fans(v) Metal Exhaust Fan 300 mm
365	Supplying fitting & fixing earthing with copper earth plate 600x600mmx6mm thick including accessories & providing masonary enclosure with cover plate having locking arrangement & watering pipe with charcoal, salts etc complete as required.
366	Copper Earth Plate Electrode
367	Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized pedestal/ floor mounted Power Supply Panel Board of approved size and 450mm deep made out of 2mm thick CRCA sheet steel with suitable size compartments, Al. Bus bars, switchgears, voltmeters, ameters with selector switches etc including powder coating painting with accessories, hardwares, etc. required for completeness and as per attached specification, direction of engineer, PWD standards and Electrical Inspectorate standards,
368	The panel board shall house: 1 No 4pole 400A MCCB, 65kA as normal supply incomer;4 Pole 400 A Al. busbars;3 Nos. Current transformer of 200/5A;1 No Ammeter with selector switch:1 No 0-500V Voltmeter with selector switch;3 Nos. LEDs: 7Nos 4 pole, 63A MCB, 25 kA as outgoing feeders9 No.s DP, 40 A MCB, KA as outgoing feeders
369	Supplying, fixing, connecting, testing & commissioning of calling bell/bell indicator type suitable for230V as well as battery operated complete with all necessary acessories
370	Dingdong bell
371	Supplying fitting & fixing of LED STRIP LIGHTS surface or wall mounted with all necessary accessories.
372	LED Strip Lights
373	Supplying fitting & fixing of LED MIRROR LIGHTS surface or wall mounted with all necessary accessories.
374	Supplying, Installation, Testing & Commisioning of 1x9 watt LED Mirror light fixture wall mounted with electronic high efficiency electronic driver as cpmplete required. (Philips Make, Cat No-31083 shell line or equivalent)
375	LED Mirror Lights
376	Supplying fitting and fixing of Telephone And switchboard Cables
377	1 Pair 0.50mm
378	Supplying fitting and fixing of LAN (COMPUTER CABLES)
379	RG-11 CSS armoured
380	Supplying fitting and fixing of LAN (COMPUTER CABLES)
381	CAT-5E
382	CAT-5E Armoured FTP
383	Supplying & fixing of ABC DRY POWDER fire extinguisher including will all necessary accessories.
384	Supplying installing fixing ABC DRY CHEMICAL POWDER Fire Extinguisher of 10kg trolley mounted confirming to IS: 2171 and CO2 Cartridge confirming to IS: 4947 Powder Confirming to IS: 4308
385	Supplying, fitting & fixing of DND ( Do not Disturb indicator) Internal Unit 2 Module ISI Mark with Mounting plate and box with wiring connections complete.
386	Supplying, fitting & fixing of DND ( Do not Disturb indicator) External Unit 2 Module ISI Mark with Mounting plate and box with wiring connections complete.
387	Supplying and Drawing of KEY CARD Switch 230V TAG Switch ISI Mark with Mounting plate and box with connections complete.
388	HAIRE VRF AIR-CONDITIONING SYSTEM FOR BLOCK- A
389	Supplying of 1 X 26 HP + 1X 20 HP DC-INVERTER HAIER MRV (Variable Refrigerant Flow) A.C. Unit. consisting of Two Outdoor units, Five Nos. 3.2 TR. Round Way Cassette A.C. Indoor Units and Fourteen Nos. 1.59 Slim Duct Indoor Units. The Indoor units can be can be operated individually with a remote control. The air cooled outdoor unit consists of Energy Efficient Scroll Compressor, can be installed in an open space as per the site suitability, equipped with overload protector and with valve protection to make the unit more durable (Operating Voltage: 440 ± 10%, 50 Hz, 3 phase). Aesthetically sound, with wide angle of air distribution and super quite operation.
390	Low side works towards -- Installation of indoor units, installation of outdoor units, providing & installation of Y-Joints, providing & installation of copper refrigerant pipes between indoor & outdoor units along with nitrile tubular insulation, providing & installation of condensate drain water piping with nitrile tubular insulation, providing & installation of communication cable 1.5 sq mm 2C shielded copper, providing, gas charging, testing & commissioning
391	Airt Quality Monitoring
392	Water Quality Monitoring
393	Noise Levels Monitoring
394	Doctor’s visit to Construction Camp every fortnight forchecking of basic health of the workers.
395	Provision for helmet, gumboots, jackets, goggles, N95masks, Sanitisers, etc. to labourers. Lump sum
396	Bio Toilets in Construction CampSupply of D.R.D.O Technology Bio-Digester tanks Rotamoldeddouble wall manufactured in automatic Rotamoldingmachines using superior grade Virgin LLDPE(Polymer) with 2.5% Carbon Black, UV Resistant Polymerleading to highest quality consistency. Thickness of theouter shell of minimum 6mm, partitions made from HDPEPolymer of 8mm thick. Immobilization Matrices of HeavyDuty Poly Grass PVC Matting lining along the partitions onboth sides. Heavy duty pipes & fitting shall be used in these tanks of Finolex or equivalent make. Fasteners made ofBrass shall be used inside the tank with manufacturer’s testcertificate and including AMI (Bacteria) of 600 liters pertank.Size of Tank: 2000 Litres capacity upto 20-30 users per day;Tank Diameter of 1425mm; Tank Height of 1600mm;Outlet pipe diameter 75mm; inlet pipe diameter 110mm.
397	FRP Toilet Cabin IWC (Ceramic Pan) type of size 1250mm X 915mm X 2400mm with ± 5% tolerance.
398	Plumber(Skilled)
399	Plumber(unskilled)
400	Earthwork
401	Earthwork in excavation by manual means upto a depth 2m below the existing ground level for foundation trenches of foundations, footing of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.
402	In all kinds of soil
403	Extra over item no. 2.1 and 2.2 above for each 1m depth or part thereof beyond the initial depth of 2 m.
404	Earthwork in filling(excluding rock)in trenches,plinth,sides of foundation etc in layers not exceeding 20cm thick including breaking of clods, consolidating each layer by ramming and watering,lead up to 50m and lift upto 1.5m
405	With available excavated earth
406	Sand filling in plinth in layers not exceeding 150 mm thick including breaking Of clods, consolidating by ramming and watering complete as directed (maximum depth 45 cm)
407	Sub Head : Site Preparation
408	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 in above ground level and removal of rubbish up to a distance of 50 in outside the periphery of the area cleared.
409	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
410	Surface dressing The ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m.
411	Sub Head : Random Rubble Masonry With Cement Mortar
412	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12(1cement:6 coarse sand :12graded stone aggregate 20mm nominal size)upto plinth level with .
413	Cement mortar 1:6 (1cement : 6 coarse sand)
414	Providing regular stone masonry in retaining walls etc. with coursed, hammer dressed or blunt chisel dressed stones Of heavy section not less than 25x25x30 cm with proper key stone each not less than 25x25x75 cm long sct in cement mortar 1 :6 (1 cement: 6 sand) including filling Of trenches and providing of weep holes at 1.20 to 1.50 metres apart staggered.
415	Providing boulder or stone filling with boulders or stones 15 cm size, 60 cm wide behind the rctaining wall etc. complete as directed.
416	Sub Head : Stone Soiling
417	Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.
418	Stone soiling
419	100mm
420	150 mm
421	Sub Head : Cement Concrete Works
422	Plain cement concrete floor base in prop 1 :3:6 laid in alternate bays as specified with coarse aggregate Of size 13 mm to 32 mm including dewatering if necessary, and curing etc. complete.
423	100 mm thick in prop 1:3:6
424	Plain cement concrete works in foundation bed for footing steps,walls,brick works etc.below plinth level as directed and specified including dewatering if necessary and curing complete(shuttering where necessary shall be measured and paid separately)
425	In prop. 1:3:6 (1 cement: 3 coarse sand: 6 coarse agg. By volume using mixture machine)
426	1 :4:8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size)
427	65 mm thick cement concrete flooring with concrete hardener topping under layer 50mm thick cement concrete in proportion 1:2:4 (1 cement: 2 coarse sand: 4 grtaded stone aggregate of 20 mm nominal size) and top layer 15 mm thick ce,ment hardener consisting of mix 1:2 (1 cement hardener mix:2 graded stone aggregate, 6 mm nominal size) by volume,hardening compound mixed @2litre per 50kg of cement or as per manufacturer's specification.this includes cost of cement slurry,complete.
428	Sub Head : Shuttering
429	SHUTTERING/FORMWORK Centering and shuttering including strutting,propping etc and removal of form for all heights complete and as directed by Engineer in charge
430	Foundation, footings, bases of columns, etc. for mass concrete works(using steel)
431	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc (using steel)
432	Slabs,roofs,landings,balconies and access platform, shelves (using steel)
433	Lintels,beams,plinth beams,girders, bressumers and cantilever(using steel)
434	Columns, pillars, piers, Abutments,posts & strut(using steel)
435	Stairs/spiral staircase, (excluding landings) (using timber)
436	Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards (using timber).
437	Edges of slabs and breaks in floors and walls(using timber)
438	Sub Head : RCC Work
439	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuterring, finishing and reinforcement. All work upto plinth level
440	M20 or 1:1 1/2:3 (1cement :1 1/2 coarse sand:3graded stone aggregate 20mm nominal size
441	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, fillets, columns, pillars, posts and struts etc. above plinth level up to first floor level, excluding cost of centering, shuttering, finishing and reinforcement:
442	M20 or 1 :11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
443	Reinforced cement concrete work in beams, slabs, roofs having slope up to 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to first floor level, excluding the cost of centerlng, shuttering, finishing and reinforcement.
444	M20 or 1 :11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
445	Sub Head : Brick Work
446	Brick work in cement mortar with 1st class brick including racking out joints and curing completely in super structure above plinth level upto first floor level including dewatering if necessary as directed.
447	In proportion 1:6 (1 cement:6 Sand)
448	Brick on edge flooring with lst class bricks on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common bum clay non modular bricks:
449	1 :6 (1cement: 6 coarse sand)
450	Sub Head : Plastering
451	15 mm thick cement plaster on the rough side of single or half brick wall of mix:
452	In cement mortar 1:4
453	20 mm cement plaster of mix:
454	In cement mortar 1:4
455	Sub Head : FLooring And Finishing Works
456	Filling sunken floor with broken brick bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels.
457	Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size ), reinforced with 1.6 mm dia. mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.
458	50 mm thick
459	Cement concrcte floor topping 1:1:2 (1 cement: 1 coarse sand: 2 stone aggregate) finished with a floating coat of neat cement, including cement slurry, complete
460	Cement plaster skirting up to 30 cm height, with cement mortar 1 :3 (1 cement: 3 coarse sand), finished with a floating coat of neat cement.
461	Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations Of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish ctc. complete at all levels.
462	Granite of any colour and shade
463	Area of slab up to 0.50 sqm
464	Stone tile (polished) work for wall lining over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.
465	Granite of any colour and shade
466	Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to ls:15477, in average 6 mm thickness, including grouting of joints
467	Deluxe range
468	Providing Vitrified Antiskid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.
469	Deluxe range
470	Providing polished VITRlFIED wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.
471	Deluxe range
472	Providing exterior wall cladding with flagstones Of 25mm average thickness on 20 mm thick plaster 1 :3 (1 cement: 3 coarse sand) and jointed with grey cement slurry complete as directed.
473	Providing and fixing wall-to-wall shower enclosure (JAQUAR - Optima make or equivalent) comprising one fixed toughened glass panel and one sliding glass door – 2 part, made of 8mm thick clear/tinted toughened glass, with aluminium/steel profile in Chrome / Black / Gold finish, including all necessary fittings, fixtures, handles, rollers, gaskets, silicon sealant, complete as per manufacturer’s specification and as directed by the Architect and Engineer-in-Charge. (material to be procured from JAQUAR GROUP)
474	Providing and fixing wall-to-wall shower enclosure (JAQUAR - DELTA make or equivalent) comprisingCorner entry half round shower enclosure with curved sliding door, made of 6mm thick clear/tinted toughened glass, with aluminium/steel profile in Chrome / Black / Gold finish, including all necessary fittings, fixtures, handles, rollers, gaskets, silicon sealant, complete as per manufacturer’s specification and as directed by the Architect and Engineer-in-Charge. (material to be procured from JAQUAR GROUP)
475	Providing and laying 500x500x40 mm thick Turf paver on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.
476	Providing and laying paver over a base of 100 mm compacted sand gravel including cutting where necessary finished with flush pointing with cement slurry mixed withapproved pigment to match shade of tiles complete at all levels as specified and directed.
477	Sub Head : Water Proofing
478	Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:Providing and laying water proofing treatment in sunken portion of WCs,bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. (b) 2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air ciire for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing Of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
479	Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:
480	(a) After surface preparation 1st layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound @0.253 kg/sqm.(b) Laying 2nd layer of Fibre glass cloth when the lst layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) 3rd layer of 1.5'mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around.(d) 4th and final layer Of brick tiling with cement mortar (which will be paid for separately).For the purpose of measurement the entire treated surface will be measured.
481	Providing and fixing Of expansion joint system related with floor location as per drawings and direction of Engineer-ln- Charge. The joint system will be of extruded aluminium base members, self-aligning/ self-centering arrangement and support plates etc. as per ASTM 8221-02. The system shall be such that it provides floor to floor/ floor to wall expansion control system for various vertical location in load application areas that accommodates multi directional seismic movement without stress to its components. System shall consist Of metal profiles with a universal aluminium base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer's pre-engineered self-centering arrangement that freely rotates/ moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminium extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufacturer's design and as approved by Engineer-in-Charge. (Material shall confirm to ASTM 6063.)
482	FloorJoint upto 100 mm gap
483	Sub Head : STRUCTURAL STEEL AND ALLIED WORK
484	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc„ including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
485	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in positionand applying a priming coat of approved steel primer all complete.
486	Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel eta. As required.
487	ln gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
488	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, Vc fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered).
489	Supplying, fitting and fixing in position reinforcement bars upto first floor level, conforming to relevant I.S. code for RCC work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and bending with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurements for the same is required)
490	High Yield Strength Deformed Bars or Tor Bars
491	Thermo-Mechanically Treated bars
492	Sub Head : ROOFING
493	Providing and fixing pre-coated galvanised iron profile sheets (size, shape and pitch Of corrugation as approved by Engineer-in-charge) 0.50 mm(+O.05 a/o) total coated thickness with zinc coating 120 grams per sqm as per ls:277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side Of the shect and polyester top coat 15-18 microns. Sheet should have protective guard film Of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 mcter or as desired by Engineer-incharge. The sheet shall be fixed using selfrdrilling/ selftapping screws of size (5.5x55 mm) with EPDM seal, complete up to any pitch in horizontav vertical or ciirved surfaces, excluding the cost of purlins. rafters and trusses and including cutting to size and shape wherever required.
494	Providing and fixing pro-coated galvanised steel sheet roofing accessories 0.50 mm (+0.05 a/a) total coated thickness, Zinc coating 120 grams per sqm as per ls:277, in 240 Mpa Steel grade, 5-7microns epoxy primer on both side Of the shect and polyester top coat 15-18 microns using self-drilling/ selftapping screws complete:
495	Ridges plain
496	Flashing/ aprons
497	Barge board
498	Gutter
499	Providing corrugated G.S or galvanised iron sheet roofingincluding vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen anda.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat Of approved steel primer and twocoats of approved paint on overlapping of sheets complete(up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost Of purlins, rafters and trusses and includingcutting to size and shape wherever required
500	0.45 mm thick with zinc coating not less than 275 gin/sqm

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents
10	Click here to download tender document	Tender Documents
11	Click here to download tender document	Tender Documents

Also Visit

Tenders

Meghalaya Tenders

Construction Tenders

Sports Infrastruture Tenders

Sports Complex Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Proposed Upgradation Of Tourism Amenities At The Umiam Water Sports Complex (Block-A) At Umiam, Meghalaya, And Proposed Redevelopment Of Orchid Lake Hospitality Complex (Block-B) At Umiam, Meghalaya., Umiam-Meghalaya

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Proposed Upgradation Of Tourism Amenities At The Umiam Water Sports Complex (Block-A) At Umiam, Meghalaya, And Proposed Redevelopment Of Orchid Lake Hospitality Complex (Block-B) At Umiam, Meghalaya., Umiam-Meghalaya

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us