|
| 1 | GST % for the tender Please select the rate of GST in cell AY13. Rate selected shall be applicable for the entire BoQ. |
| 2 | Construction of Building as per specification and drawing: |
| 3 | Site cleaning: Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil. |
| 4 | FILLING EARTH: Supplying and filling selected earth/ moorum (excluding black cotton soil) from Contractor's own borrow areas including royalty, with all leads and lifts in low laying areas and filling to required grade and level including watering, compacting at optimum moisture content to 90% of Proctor's density, consolidation and rolling with 8 to 10 tonne power roller in layers not exceeding 20 cm thickness, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 5 | SAND FILLING: Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Antitermite Treatment: Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 7 | Antitermite Treatment: Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : |
| 8 | i) Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/ sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete with Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 9 | ii) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 : 2 (1 cement : 2 Coarse sand) to match the existing floor with Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 10 | iii) Treatment of existing masonry using |
| 11 | FLAT BRICK SOLING: Supplying and laying flat brick soling in foundation trench, in floors, garages, sumps, etc., with bricks of class designation 50 laid to proper slope, level and grade etc. filling of the joints with sand etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of the Site Engineer. |
| 12 | PCC (1:2:4): Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level with 1:2:4 (1 cement : 2 coarse sand (Zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 13 | RCC(1:1.5:3): Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 14 | RCC(1:1.5:3): Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 15 | RCC(1:1.5:3): Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 Degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Shuttering: Centering and shuttering including strutting, propping etc. and removal of form for all heights : |
| 17 | (i) Foundations, footings, bases of columns, etc. for mass concrete |
| 18 | (ii) Suspended floors, roofs, landings, balconies and access platform |
| 19 | (iii) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 20 | REINFORCEMENT: Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level - Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 21 | REINFORCEMENT: Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level - Thermo-Mechanically Treated bars of grade Fe-500 D or more |
| 22 | Plinth Protection: Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 23 | BRICK WORK: Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 24 | VITRIFIED TILES: Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/sq.m. including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 25 | ACID RESISTANT TILES: Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS:4457, complete as per the direction of Engineer-in-Charge. |
| 26 | (i) In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand). Acid and alkali resistant tile |
| 27 | (ii) In dado/ skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand). Acid and alkali resistant tile |
| 28 | Ceramic Tiles: Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of first quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 Kg/sq.m. including pointing the joints with white cement and matching pigment, etc. complete. |
| 29 | Wall Tiles: Providing and fixing first quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by the Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 Kg/sq.m., including pointing in white cement mixed with pigment of matching shade complete. |
| 30 | PLASTER: 15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement : 4 coarse sand) |
| 31 | Water Proof Frame: Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness.The laminates hall be moulded with fire resistant grade unsaturated polyester resin and chopped mat.Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides.M.S.stay shall be provided at the bottom to steady the frame. |
| 32 | WATER PROOF DOOR: 30mm thick Fiber glass Reinforced Plastic(F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyesterresin,moulded to 3mm thick FRP laminate all around,with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam(PUF)/Polystyrene foam to be used as filler material through out the hollow panel,casted monolithically with testing parameters of F.R.P. laminate conforming to table-3 of IS:14856, complete as per direction of Engineer-in-charge. |
| 33 | Ventilation: Providing and fixing louver type glazed ventilator made of powder coated (70micrones) Ivory / White / Coloured (approved shade) standard Aluminium section of JINDAL/INDALCO/ AJIT INDIA/ HINDALCO or equivalent approved make fixed with necessary galvanised iron lugs embedded in cement concrete block of size 15x10x10cms in 1:2:4 mix or with rawl plug and screws or nuts and bolts as required including providing and fixing 5 mm thick glass in the louver panes and wire mesh shutter at inside of the main wall frame with rubber gasket, frame, aluminium handles, peg stays etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 34 | GLASS PANES: Supply and fixing plain/ground glass panes 6 mm thick in doors,windows,partition etc fixed with necessary pins ,putty/rubber lining,T.W. battens as the case may be all labour materials etc complete |
| 35 | Door: Providing and fixing fully glazed single/double leaf doors (one side or both side opening)made of powder coated (70 microns) Ivory / White / Coloured (approved shade) with 5.5 mm thick plain glass (best Indian make ) fitted and fixed with box type 101.6 x 44.45 x3.18 mm Aluminium frame (JINDAL/ HINDALCO/AJIT INDIA) with snap beading and glazing clips, anodised transparent or dyed to required shade according to IS-1868, neoprene cushion, top pivot, locking arrangement hand rail, all accessories etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. Note: Aluminium doors provided for toilet shall consist of single layer of 5.5 mm thick frosted glass in place of transparent or coloured glass, for which no extra payment shall be made. |
| 36 | Floor Spring: Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS:6315, having brand logo embossed on the body/ plate with double spring mechanism and door weight up to 125 Kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-In-Charge With stainless steel cover plate minimum 1.25 mm thickness |
| 37 | Window: Providing and fixing fully glazed window made of powder coated (70 microns) Ivory / White / Coloured (approved shade) standard Aluminium section of JINDAL/ INDALCO/ AJIT INDIA/ HINDALCO or equivalent approved make fixed with necessary galvanised iron lugs embedded in cement concrete block of size 15x10x10cms in 1:2:4 mix or with rawl plug and screws or nuts and bolts as required including providing and fixing 5 mm thick smoke glass panes fitted with rubber gasket, glazing clips, neoprene cushion, aluminium handles, special locking arrangements, guides, all round weather strips etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. Type: Openable/ sliding type shutter with 5 mm thick glass |
| 38 | Door Closer: Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS:3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 39 | Aluminium handles: Providing and fixing 150 mm aluminium handles anodised transparent or dyed to required colour or shade with nuts and screws etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 40 | Roof Treatment: Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : (a) Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. (b) Tear strength in longitudinal and transverse direction as 300/250N. (c) Softening point of membrane not less than 150°C. (d) Cold flexibility shall be up to -2°C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane. 3 mm thick. |
| 41 | Gola: Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design In 75x75 mm deep chase |
| 42 | Khurras: Making Khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 43 | SYNTHETIC PAINT: Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 44 | EXTERIOR PAINT: Finishing walls with Acrylic Smooth exterior paint of required shade on New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 45 | INTERIOR PAINT: Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade in New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 46 | Chequerred tiles: Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand). Ordinary cement without any pigment |
| 47 | UPVC PIPE: Providing and fixing on wall face Unplasticised Rigid PVC (UPVC) rainwater pipes conforming to IS:13592 Type-A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion: (i) Single socketed pipes : 75 mm. Dia |
| 48 | PVC PIPE: Supplying and fixing of following PVC pipes (15 Kg/cm2, 6 Kg/cm2) including all PVC bends,elbows special arangements,tee, including MS clamps, brackets etc. complete as per IS 4985 : Dia: 20mm |
| 49 | PVC PIPE: Supplying and fixing of following PVC pipes (15 Kg/cm2, 6 Kg/cm2) including all PVC bends,elbows special arangements,tee, including MS clamps, brackets etc. complete as per IS 4985 : Dia: 25mm |
| 50 | PVC PIPE: Supplying and fixing of following PVC pipes (15 Kg/cm2, 6 Kg/cm2) including all PVC bends,elbows special arangements,tee, including MS clamps, brackets etc. complete as per IS 4985 : Dia: 32mm |
| 51 | European type Water Closet (EWC): Providing and fixing white vitreous china pedestal type water closet (European type) (Ref. Make: HINDWARE, Model: Cat No.-20058 or equivalent approved) with seat and lid, 10 litre low level white vitreous china dual flushing cistern (Ref. Make: HINDWARE, Model: Cat No.-21028 or equivalent approved) & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid. |
| 52 | CP brass tap: Providing and fixing 15mm diameter C.P. brass tap as per following with C.P. brass flange including cutting & making good the walls wherever required, etc. complete in all respects inclusive of cost of all materials, labour, tools, tackles etc. as per specifications and directions of the Engineer-in-Charge. Bib Cock (Ref. Make: JAQUAR, Model: Cat. No. 0021 or approved equivelent) |
| 53 | Water Tank: Providing and placing on terrace (at all floor levels) polyethylene water storage tank (Ref. Make: SINTEX or approved equivalent), IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular Tank |
| 54 | Towel Rail: Providing and fixing approved quality chromium plated brass towel rail of 20mm diameter 600 mm long including chromium plated brass brackets fixed with wooden cleats and C.P. brass screws etc. complete. |
| 55 | Soap Container: Providing and fixing the following washroom fittings, complete in all respects; inclusive of cost of all materials, labour, tools, tackles etc. as per specifications and directions of the Engineer-in-Charge. : Stainless steel liquid soap container (spring loaded push type) with lid and brackets fixed to P.V.C. cleats with C.P. brass screws, etc. |
| 56 | Wash basin: Providing and fixing special coloured glazed vitreous China clay Pedestal type aesthetic wash basin of 580x500 mm size of Hindware make (Cat No. - 10050) or equivalent approved make with MS or CI brackets painted white, C.P. brass chain with rubber plug, 32 mm CP brass waste coupling of standard pattern, 32 mm CP brass bottle trap and union, 32 mm dia C.P. pipes to wall flange etc. including cutting and making good the walls & floors where required complete in all respects inclusive of cost of all required fittings, fixtures, materials, labour, tools, tackles etc. as per specifications and direction of Site Engineer. |
| 57 | Rain water pipe: Providing and fixing on wall face Unplasticised Rigid PVC (UPVC) rainwater pipes conforming to IS:13592 Type-A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion: (i) Single socketed pipes : 110 mm diameter |
| 58 | Shower: Supplying and fixing 150 mm dia C.P. shower rose (heavy quality) with 15 mm dia. Inlet including supply of bend and 20mm C.P. stop cock (heavy quality) all respect inclusive of cost of all fixtures . |
| 59 | Urinal: Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 60 | Flush Pipe: Providing & fixing in position 32 mm dia galvanized steel telescopic flush pipe of Penguin, Soma or any approved make complete including cutting and making good the walls & floors including removing the damaged flush pipe etc complete. |
| 61 | Glass mirror: Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Size: Oval shape 450x350 mm (outer dimensions) |
| 62 | Brick Masonary Catchpit: Constructing Brick Masonary catch pit in cement mortar 1:4 (1 cement : 4 coarse sand) including necessary excavation, 200mm thick foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm size) and inside and top plastering (15mm thick) with cement mortar 1:4 (1 cement : 4 coarse sand) finished with a floating coat of neat cement making necessary connections to drains inclusive of all labour, material, equipment, etc., all complete as per drawing and directions of the Engineer-in-Charge. Size - 600mm x 600mm x depth up to 750mm inner dimensions |
| 63 | Septic tank: Constructing brick masonry Septic Tank with brickwork in cement mortar 1:6 including R.C.C. 1:2:4 (1 cement : 2 sand : 4 graded coarse aggregate) top slab, C.I. cover all as per standard drawing, etc. complete in all respects inclusive of cost of all materials, labour, tools, tackles etc. as per drawings, specifications and directions of the Engineer-in-Charge. (For 10 Users) |
| 64 | PVC Pipe: Supply of PVC pipes & fittings (medium duty) conferming 150 mm dia (uppercasing Pipe as per ASTMD-1785) (30 m x 2 pumps) complete in all respect as per site engineer and EIC direction |
| 65 | PVC Pipe: Supply of PVC pipes & fittings (medium duty) conferming to ASTMD-1785 dia. 50 mm (Main Pipe) (350 m), complete in all respect as per site engineer and EIC direction |
| 66 | Strainer: Supply of high density polythene-strainer of approved make and 50 mm or required size as per site condition with adapter conforming to IS specification & as per direction of EIC |
| 67 | Water Testing: Collecting sample of water for Bacteriological and chemical test from any depth at any time during excution of work including hire and labour charges for tools and plants and sterilising the equipment , pay all charges and fees, testing etc. complete in all respect as per direction. |
| 68 | Submersible pump: A) Installation / testing / commissioning of i) 1HP Solar Submersible Pump, ii) 1HP MPPT Pump Controller, iii) 300W (144 cell) Solar PV Module – 3Nos with all attachment complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 69 | Construction of RCC road at SV locations |
| 70 | EARTH WORK: Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by the Engineer-in-Charge. All kinds of soil. |
| 71 | Sub-grade: Preparation and consolidation of sub-grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead up to 50 metres. |
| 72 | SAND FILLING: Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 73 | FLAT BRICK SOLING: Supplying and laying flat brick soling in foundation trench, in floors, garages, sumps, etc., with bricks of class designation 50 laid to proper slope, level and grade etc. filling of the joints with sand etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of the Site Engineer. |
| 74 | RCC: Providing and laying design mix cement concrete of M-30 grade in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of the Engineer-in-Charge. [Notes: (1) Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately. (2) Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately]. Cement concrete prepared with batch mixing machine |
| 75 | Bitumen Sealing: Providing and laying in position bitumen hot sealing compound for expansion joints etc. using Grade 'A' sealing compound (Measurement shall be taken for per CM width, per CM depth and per M length). |
| 76 | REINFORCEMENT: Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more Please Enable Macros to View BoQ information |
