|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) |
| 3 | Brick work with common burnt clay modular bricks of class designation 7.5 in (a) Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 4 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :(a) cement mortar 1:4 (1 cement : 4 coarse sand): |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:1½:3 (1 Cement: 1½ coarse sand) : 3graded stone aggregate 20 mm nominal size): |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : |
| 7 | a). Suspended floors, roofs, landings, balconies and access platform |
| 8 | b). Edges of slabs and breaks in floors and walls. i). Under 20 cm wide |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.(a) Thermo-Mechanically Treated bars of grade Fe-500D or more: |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size): |
| 11 | 15 mm cement plaster on the rough side of single or half brick wall of mix (a) 1:4 (1 cement: 4 fine sand): |
| 12 | Making soak pit 2.10 m diameter 2.30 metre Deep with 23 x 23 cm brick honey comb shaft in Ccement mortar 1:6 filled with sand and brick bats and C.I cover with frame complete as per standard design or as per the direction of Engineer-in Charge. |
| 13 | Supplying and fixing C.I. cover with frame for manholes (a) 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg: |
| 14 | Providing and Placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank: |
| 15 | Providing and fixing brass stop cock of approved quality : a). 15 mm nominal bore |
| 16 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : a). 15 mm nominal bore: |
| 17 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (a) 15mm Dia Nominal Bore: |
| 18 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall a). 15mm Dia Nominal Bore: |
| 19 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : a). 15/20/25 to 25/40 mm nominal bore |
| 20 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a). White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 21 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: a). White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 22 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 23 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board a). 610x460 mm bowl depth 200 mm |
| 24 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. a). Flexible Pipe 32mm dia |
| 25 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 26 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 27 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 28 | Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass Screws. |
| 29 | Providing and fixing C.P. Brass Towel Rail complete with C.P. Brass brackets fixed to wooden Plugs with C.P. Brass Screws. i). 600 mm x 20 mm. |
| 30 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931. a). 15 mm nominal bore |
| 31 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. a). 15 mm nominal bore |
| 32 | Providing and fixing C.P. Brass Pillar Tap with capstan head a). 15 mm nominal bore |
| 33 | Providing and fixing C.P. brass angle valve for basin mixer, pillar cock, cistren and geyser points etc. of approved quality conforming to IS:8931 |
| 34 | Providing and fixing uplasticised PVC connection pipe with brass unions :(a) 45 cm lenth 15mm Dia Nominal Bore |
| 35 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS: 1729 |
| 36 | Providing and fixing 100 mm sand cast Iron grating for gully trap: |
| 37 | Providing and fixing high pressure PVC spigot and socket, waste and Ventilating Pipes ISI marked including fixing with approved adhesive etc. Complete. |
| 38 | a). 110 mm Dia. |
| 39 | b). 75 mm Dia. |
| 40 | Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. Complete. |
| 41 | a). 110 mm Dia. |
| 42 | b). 75 mm Dia. |
| 43 | Providing and fixing PVC Door bend with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. Complete. |
| 44 | a). 75 mm Dia. |
| 45 | Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. Complete. |
| 46 | a). 110 mm Dia. |
| 47 | b). 75 mm Dia. |
| 48 | Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. Complete. |
| 49 | a). 110 mm Dia. |
| 50 | b). 75 mm Dia. |
| 51 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. Complete. |
| 52 | a). 110 mm Dia. |
| 53 | b). 75 mm Dia. |
| 54 | Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. Complete. |
| 55 | a). 110 mm Dia. |
| 56 | b). 75 mm Dia. |
| 57 | Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: (a) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Please Enable Macros to View BoQ information |
