|
| 1 | 1- Road maintenanceProviding spot reconditioning, reconstruction and regravelling to repair specific erosion or other damages for restoring the eroded area to originally constructed cross section on cuts and fills slopes/shoulders conforming to Technical Specifications Clause no. 3002. Fill material should be brought from borrow areas located outside ROW conforming to Technical Specification no. 305. Watered and well compacted with plate compactor or power rammer with all leads and lifts as directed by the Engineer (Quantity of compacted Fill material to be measured on cross sectional area basis) (SOR Item No.-3.14) |
| 2 | Removal of rank vegetation/weeds and undesirable vegetation from shoulders, embankment slopes upto ROW (both sides) complete in all respects including breaking of clods, rough dressing and disposal of waste material and vegetation at a place outside ROW as per direction of Engineer-In-Charge and as per Maintenance Standards Clause 3.3 (Frequency will be once in a quarter). (SOR Item No.-2.2)a) Shoulders including side slopes of embankment up to toe line on both sides of the carriageway. (Frequency of cleaning will be four times in a year; however limited to only areas prone to growth of rank/undesirable vegetation and weeds). |
| 3 | Providing slurry seal for filling of hair cracks, surface cracks and preventive/renewal treatment as per MoRTH Specification Clause 512.b) Filling of surface cracks 1-3 mm and preventing/ renewal treatment. |
| 4 | Repair of localized failed areas of PQC by marking the area, removing the failed area using jack hammer, saw cutting to full depth of PQC, replacing membrane, clearing the area from dust and debris. Placing M-40 grade PQC in a depth equivalent to the existing depth of PQC and installing existing expansion joint/other joint (if there was one). |
| 5 | Sealing of crack/porous concrete with Epoxy grout by injection through nipples complete as per Clause 2803 of Technical Specifications and as per approval of the Engineer. |
| 6 | Cement plaster/repair to cement plaster in thickness 12-20 mm in cement mortar 1:3 on all types of masonry works in superstructure/substructure at any height as per MoRTH Specifications Clause No. 1000, 1300 and 1400. (SOR Item no. 583) |
| 7 | Repair to all types of damaged stone/brick masonry work in superstructure and substructure of bridges/CD works including dismantling of damaged portion and reconstructing to match with existing pattern without causing any damage to the structure in cement work complete in all respects including testing etc. as directed by the Engineer conforming to MoRTH Specifications Clause no. 1000, 1300 and 1400. The rate quoted should be after due consideration of the salvage value of the dismantled material. (SOR Item no. 305)a) Repair to brick masonry in 1:4 cement sand mortar. |
| 8 | Providing, laying and compacting Wet Mix Macadam (WMM) base course with approved materials complete as per Technical Specifications Clause no. 406 of MoRTH |
| 9 | Providing and applying primer coat with RS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 to 1.00 kg/sqm using mechanical means. |
| 10 | Providing, laying and compacting Dense Graded Bituminous Macadam complete as per technical Specification Clause no. 505 |
| 11 | Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.30 kg per sqm on the prepared bitumen/granular surface cleaned with mechanical broom. |
| 12 | Providing, laying and compacting Bituminous Concrete as per technical Specification Clause no. 507 |
| 13 | 2- Road property maintenancePainting with high gloss synthetic enamel paint two coats to give an even and smooth surface for protection of exposed concrete/masonry portion of Bridges/CD works/parapet, kerb painting and repairing wherever necessary, complete as per approval of the Engineer. (SOR Item no. 10.5)a) Old existing surface |
| 14 | b) New surface after applying priming coat with cement primer (two coats) of approved quality. (SOR Item no. 10.5) |
| 15 | Providing and fixing reinforced cement concrete M-15 grade 5th kilometer stones, kilometer stones and hectometer stones of Standard Design as per IRC:8- 1980 and MoRTH Specification Clause 804 including two coat painting with synthetic enamel paint after applying approved quality cement primer and printing letters with approved quality synthetic enamel paint on both sides as per MoRTH Specification Clause 804 and as per drawing and direction of the Engineer-in- Charge. The job includes fixing of these distance- measuring stones at places after dismantling of existing damaged stones, and further disposing of dismantled material outside ROW. Rates quoted to be inclusive of the salvage value of the useful material obtained during the course of dismantling. The fixing of these stones shall be done with M-10 cement concrete as per drawing and approval of the Engineer-in-Charge.a) Hectometer stones |
| 16 | b) Kilometer stones |
| 17 | c) 5th Kilometer stones |
| 18 | Replacement of stolen/missing retro-reflectorised traffic sign boards by providing and fixing new retro- reflectorised cautionary, mandatory and informatory sign as per ASTM D 4956-04 made of High intensity grade Microprismatic sheeting Type-IV, fixed over aluminium sheeting 2.0 mm thick supported on a MS Angle Iron Frame comprising of 40 mm X 40 mm X 4 mm. This frame is further welded to MS Angle 75 mm X 75 mm X 6 mm size, 3.5 meter high vertical post complete as per drawing. This vertical post shall be embeded in M-15 grade cement concrete in a pit of size 450 mm X 450 mm X 600 mm, 600 mm below ground level complete in all respects as per direction of the Engineer.a) Informatory Signi) Accident Prone Sign 800 mm X 600 mm |
| 19 | b) Cautionary/Warning signi) Triangular 900 mm side |
| 20 | ii) Hazard 30x90 cm (Left/Right) |
| 21 | iii) Chevron 50x60 cm side |
| 22 | c) Mandatory/Regulatory signi) Octagonal “STOP” sign |
| 23 | ii) 600 mm dia Circular Speed sign Board |
| 24 | upplying and installation of delineators (Roadway indicators) 95 cm high above ground level of total length 135 cm painted black and white in 15 cm wide strips fitted with 3 nos. rectangular microprismatic reflective sheeting fixed on 2 mm thick aluminum sheet of size 80 mm X 100 mm one in each black strip duly riveted in the rectangular tubular section facing direction of traffic. Rectangular Tubular section of size 100 mm X 50 mm X 3 mm (thickness). The Tubular section of the delineator is encased all around with steel welded wire mesh of thickness 2.5 mm, in size 120 mm X 70 mm X 760 mm as shown in the drawing. The welded wire mesh is painted with two coats synthetic enamel white paint after applying two coat red oxide primer. The delineator is embedded in M-15 cement concrete in pit size 300 mm X 300 mm X 450 mm. The rate quoted is for the complete job as per Drawing and direction of Engineer. |
| 25 | Cats Eye/Pavement Marker (NMC nail Less):- Made out of Acrylic-strene-Acrylonitril or Hi-Impect polysterene fitted with Moulded of Methacrylate (NMC) reflector cube corner reflector design; Filled with tightly adhering potting compound as per ASTM D788 size 11.5 cm X 7cm X 1.6 cm or 10 cm X 10 cm X 1.75 cm provided with bituminous adhesive in sufficient quantity with each unit for fixing. No nail should be allowed for fixing. |
| 26 | Providing and marking of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms/sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished Surface to be level, uniform and free from streaks and holes complete in all respects. The job includes marking of centre line, shoulder line, edge line, zebra crossing marking, arrows and dashes marking at the junctions as per Technical Specifications Clause 803.4 complete in all respect and as per approval of the Engineer-in-Charge. |
| 27 | roviding and fixing single faced W-Beam metal crash barrier (W-profile safety guard rails) made out of the following members. Job includes erection complete in all respects as per MoRTH Specifications clause no. 810 and using M-20 grade cement concrete wherever required as directed by the Engineer. Beam made out of cold rolled steel strip W profile double of 3 mm thick having a minimum yield strength of 2400 kg/sqcm having width of 313 mm and depth of corrugation as 83 mm hot dip galvanized of zinc coating @ 550 gm/sqm. Post consisting of cold rolled channel 150 mm x 75 mm x 5 mm and spaced 2 mtr. centre to centre having minimum yield strength of 2400 kg/sqcm. The length of post shall be 1900 mm and minimum height of post above concrete foundation shall be 800 mm, hot dip galvanised of zinc coating @ 550 gm/Sqm, the post shall be fixed as required |
| 28 | Providing and marking of hot applied thermoplastic compound 15 mm thick including reflectorising glass beads @ 250gms/sqm area, thickness of 15 mm is exclusive of surface applied glass beads as per IRC:35. The finished Surface to be level, uniform and free from streaks and holes complete in all respects. The job includes marking of center line, shoulder line, edge line, zebra crossing marking, arrows and dashes marking at the junctions as per Technical Specifications Clause no. 803.4 complete in all respects and as per approval of the Engineer-in-Charge. (Repeated Bar Line) |
| 29 | 3- Performance Based Incident Management And Pavement RepairsProviding treatment and repair to pot holes/ruts of any depth/patch repair of all types of bitumen pavement complete as per Technical Specification Clause 3004.2, and as per direction of Engineer by using paving grade bitumen/emulsion/cold ready mix material. The job includes removal of all failed material, trimming of completed excavation to provide firm vertical faces, cleaning of surface, painting of tack coat on the sides and base of excavation as per Clause no. 503, back filling the patch with bituminous material as per Clause no. 509. Compacting trimming and finishing the surface to form a smooth continuous surface all as per Clause no. 3004.2 of Technical Specifications. Please Enable Macros to View BoQ information |
