|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 7 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 9 | Foundations, footings, bases of columns, etc. for mass concrete |
| 10 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 11 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 13 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 14 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 15 | 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | 12 mm cement plaster finished with a floating coat of neat cement of mix: |
| 17 | 1:4(1 cement: 4 fine sand) |
| 18 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 19 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 20 | Kitchen sink with drain board (510x1040 mm bowl depth 250 mm) |
| 21 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 22 | Semi rigid pipe (32 mm dia) |
| 23 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 24 | 15 mm nominal bore |
| 25 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall |
| 26 | 15 mm dia nominal bore |
| 27 | 20 mm dia nominal bore |
| 28 | 25 mm dia nominal bore |
| 29 | 40 mm dia nominal bore |
| 30 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 31 | 25 mm nominal bore |
| 32 | 20 mm nominal bore |
| 33 | 40 mm nominal bore |
| 34 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 35 | 20 mm nominal dia Pipes |
| 36 | 25 mm nominal dia Pipes |
| 37 | Providing and fixing ball valve (CPVC) of approved quality: |
| 38 | 25m mm nominal bore |
| 39 | 20m mm nominal bore |
| 40 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 41 | 110 mm diameter |
| 42 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 43 | Single tee with door 110x110x110 mm |
| 44 | Bend 87.5° 110 mm bend |
| 45 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer- in-charge |
| 46 | Extruded section profile size 48x40 mm |
| 47 | Providing and fixing to existing door frames. |
| 48 | 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. `U' cleats. The shutter frame filled with a uPVC multi- chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in- charge. |
| 49 | Providing and fixing brass bib cock of approved quality : |
| 50 | 15 mm nominal bore |
| 51 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 52 | 30 cm length 15 mm nominal bore |
| 53 | Providing and fixing brass stop cock of approved quality : |
| 54 | 15 mm nominal bore |
| 55 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 56 | 10 litre capacity - White |
| 57 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material including malba, all complete as per the direction of Engineer-in charge. |
| 58 | Long pattern W.C Pan of size 580x440 mm |
| 59 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 60 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 61 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 62 | G.I. pipes |
| 63 | Providing and fixing semi-circular UPV 250mm rain water pipe gutter of \\"Rainfit \\"make or equalivent with UPVC Support bracket screw and washers etc., including making necessary connections with rain water pipes complete. |
| 64 | Replacement of damaged existing Gutter |
| 65 | Providing and fixing UPVC joint bracket / accessories for UPVC pipes rain water pipe including jointning with solvent. |
| 66 | UPVC Joint Bracket 250mm dia |
| 67 | Providing and fixing UPVC stop end outlet / accessories for UPVC pipes rain water pipe including jointning with solvent. |
| 68 | UPVC stop end outlet 250mm |
| 69 | Providing and fixing UPVC short stop end / accessories for UPVC pipes rain water pipe including jointning with solvent. |
| 70 | UPVC stop end 250 |
| 71 | Providing and fixing M.S. presseds RAFTER BRACKET SIDE or Upside fixing with necessary screws etc. complete : |
| 72 | RAFTER BRACKET 464mm x20mm |
| 73 | Providing and fixing of Rainwater Filter of make \\"Rainy Brand\\" or equivalent for rain water harvesting suitable for area upto 180Sqm ,filter type opend end ,non -clog with maximum dischatge 80 Liters per minute fixed with ncessary screw complete. Please Enable Macros to View BoQ information |
