|
| 1 | BSR PHED 2020-21 Labour chages for removing electric fault in wiring/making connection through lugs(with the help of cramping tool) of moto pump set with starter at headworks of water supply scheme/Tubwell/openwell including cost of insulation tape etc.6.1 |
| 2 | 6.2 Labour charges for replacement of defective ampere meter /voltmeter with new one existing panel board in pump ouse./Tubewell/openwell(new voltmerter/ampere meter will be provided by department) |
| 3 | 6.3.1 Labour charges for repairing of starter at site including opening and reassembling of starter with labour charges for replacing of defective parts with new one at site.( Parts will be supplied by Depatment) 5 to 15 HP |
| 4 | 6.3.2 - 16 to 30 HP |
| 5 | 6.5 Supply & filiing starter oil in oil immersed starter at site. |
| 6 | 57.14.2.1 RUDIP ISOR 2023 - Providing & Fixing of AC operated heavy duty 230/440 Volt power contactor as per PWD specification for electrical Works, ISI marked IS/IEC 60947 -4-1 : 2000 having provision of mechanical interlocking, auxiliary contacts, Din rail mounting type including making connections, testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/work , refer ANNEXUS “A” attached with this BSR 16 Amp ( 4 pole power contactors) |
| 7 | 57.14.2.2 - 25/32 Amp( 4 pole power contactors) |
| 8 | 57.14.2.3 - 40 Amp( 4 pole power contactors) |
| 9 | 57.9.1 - Providing & Fixing of flush head push button actuators IEC 60947 with integral circuit , IP 65 above panel & IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm,front LED cover dia min. 29 mm, contact material phospher bronze for led, PCB contacts shall be of brass ( tin plated) , impulse dielectric tested for 2.5KV , including connection etc. as required. All as per pre approved by Engineer in-charge . For additional technical parameters of products /work , refer Annexure “A”attached with this BSR. Non Luminous type |
| 10 | 57.9.2- Luminous type Red , Yellow , Green , Amber |
| 11 | 57.18.1 - Providing & Fixing of thermal over load relay with built in single phase protection and having at least 1NO & 1NC contacts, manual/auto reset facility including making connection testing etc. as required. All as pr pre approved by Engineer in-charge. For additional technical parameters of products /work, refer Annexure “A” attached with this BSR Up to 14 Amp |
| 12 | 57.9.2 -- 14 to 23 Amp |
| 13 | 57.9.3 - 20 to 33 Amp |
| 14 | 57.9.4 - 24 to 40 Amp |
| 15 | 57.19 - P & f 240 / 415 V Electronic ON –OFF Timer 3 -30 Sec /12 -120 Sec including making Connection etc. as required . All as per pre approved By Engineer in charge. For additional technical parameters of products/ work , refer Annexure ‘A” attached with this BSR |
| 16 | 57.17 - P & F of front / side mounting add on Auxiliary contact block with required NO & NC combination including making connections, testing etc. as required . All as per pre approved by Engineer in charge. For additional technical parameters of products / work , refer Annexure “ A” attached with this BSR |
| 17 | BSR PWD Electrict -8.8.1 Providing & Fixing of 110/220 V, unibody LED Indicating lamp IEC 60947 with integral circuit, IP 65 above panel & IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Red/yellow/Green colour Please Enable Macros to View BoQ information |
