|
| 1 | Providing & Fixing of following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct lit type complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/work.refer Annexure \\"A\\" attached with this BSR 1/2 Module |
| 2 | Providing & Fixing of 240/415 VAC MCB with positive isolation of 10 LA breaking capacity (B/C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage ISI marked IS 8828(1996)/ coaforming to IEC 60898-1 2002 IEC 60947-2 low watt losses trip free mechanisum energy limiting of class 3 as per IEC minimum phase termination capacity of 3.5sq.mm..conductor line load reversibility IP 20 contact protection and fitted in existing distribution board/sheets minimum electrical operation 20000 upto 20 A rating and 10 000 upto 63 A. 5000 for 10 A & above rating including making connections testing etc. is required. OEM shall have submit NABL/CPRI/ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR 6 a to 32 A rating Single Pole |
| 3 | P&F 1.2 mm thick G. I/M.S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in rocessed/surface as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 100num x 100mm x 60mm |
| 4 | 175mm x 100mm x 60mוח |
| 5 | 300mm x 100mm x 60mm |
| 6 | P&F paper phenolic resin bonded laminates confirming to IS: 2036 - 1995 for beses frames including making holes for switches ctc. with brass screws. washers/zinc plated nut and bolts as required. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR 3.0 min thick |
| 7 | S&F following sizes (dia) of ISI marked virgin material MMS (IS:9537 P-III) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameiers of product/ work reict Annexure 'A' attached with this BSK 25 mm |
| 8 | Providing & Fixing of 3/6 pin 16 amp flush type non modular socket made out from Industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products work, refer Annexure \\"A\\" attached with this BSR |
| 9 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for clectrical Works with ISI marked (IS-694) and as per IS 8130: 2013 of 1.1 kV grade. Wire should be made from 99.90% purity copper. class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss, oxygen free for less chances of oxidization, insulation PVC type A/C/D., Name retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5. in existing surface or recessed PVC/MS conduit/casing capping making connections with Copper Lugs of suitable size. Ferrules.testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR a 1 x 1.5 sq.mm |
| 10 | b 1 x 2.5 sq.mm |
| 11 | Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works. on hot dipped galvanized modular box of 18 SWG with carthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plite including cost of ISI mark.ed modular 16 amp. Switch (IS :3854) and 3/5 pin lo amp. socket outlet (IS. 1293) |
| 12 | Modular MCB 6 A 10 32 A DP (IS:8832 marked) |
| 13 | Providing & Fixing of IK10 IP65/IP66 protected LED Up - Down Luminaric Wall/Surface mounting made of powder coated die çast alluminium housing with UV stabalized PC diffuser, The System level Luminous efficacy ≥ 90 Lumen/W. COB LEDs is to be used. Sy siem CRI-70, CCT: 3000/400/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min 4KV(L-N) and efficiency > 85%, PF>0.9. THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50MKK) Burning hours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as per engineers choice, driver current <75timA. Fixture must be in compliance with BIS Standards and Trade niark Certificate complete in all respect. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with linble warrants of product/accessprics from OEM shall be submiued All as ner |
| 14 | P&F IP 65/66 Water proof high power LED Strip 5 Mir as required |
| 15 | P&F IP 65/66 LED Strip Driver 8 Amp. |
| 16 | ASHOK STAMBHTotal Height: 16.5 Feet (10' Pillar + 3' Lion Capital+ 3.5 x 3.5x3.5 feet platform)10 Feet pillar(shaft) Diameter 1.5 to 2 FeetBansi pahadpur(pink)3 Feet Ashok Stambh Foundation and stability - the structure is 16.5 feet tall and top-heavy (the 3' capital can weigh over 200 kg), a deep RCC foundation is mandatory.Design Recommendation: A 4'x4'x4' pit with a 1:2:4 concrete mix and 10mm steel reinforcement is standard for safety. Supply and fixing LED MODULE BOX With 5 mm acreylic uv printed aluminium iron frame etc LED Board Size 13.40 x 0.45 Mtr |
| 17 | Ashok Chakra 5-foot diameter Ashok Chakra carved from Bansi pahadpur (pink)Carving Complexity: The 24 spokes of the Chakra require high-relief carving and making 5 x 5 feet platform Finishing: Hand grinders for mirror polishing Please Enable Macros to View BoQ information |
