Housing Urban and Rular Development Government Departments Closing in 0 days TDR #54727915

Tender For Construction Of Infrastructure Development Of Govt.Sec. School Tai,Leparada District

Issued by Government Departments · Leparada, Arunachal Pradesh
Tender Value
Ref. Documents
Estimated cost
Bid Submission
24 Mar 2026
0 days left
EMD
1.75 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Leparada → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Construction Of Infrastructure Development Of Govt.Sec. School Tai,Leparada District

BOQ

Name of Work:- Construction of Infrastructure Development of Govt.sec. School Tai,Leparada District
Sl. No. Item Description
1SITE DEVELOPMENT
2Excavation in Hill Area in Soil by Mechanical Means (Excavation in soil in hilly area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with all lifts and lead upto 1000 metres)
3Depositing of excavated earth on the barren valley side. (Excavation in soil in hilly area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth on the Barren Valley side)
4EXCAVATION AND EARTH WORK
5Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30cm size, saturated soil and rock), lift upto 1.50m and stacking the excavated soil not more than 3m clear from the edge of the excavation and returing the stacked soil in 15cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.
6Re-filling excavated earth in foundations and plinth etc. in 15cm layer including ramming and watering etc. complete.
7Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.
8. CONCRETE WORK
9Providing and laying in foundations and plinth cement concrete 1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) excluding the cost of centring and shuttering.
10Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size)
11Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by manufacturers.
12Applying a coat of hot bitumen (mashphalte 80/100 or equivalent) using 1.70 kg. per sqm. on damp proof course after cleaing the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
13Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.
14. R.C.C. WORK
15Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in: M20 (1 cement : 1.5 cparse samd : 3 stone aggregate 20mm nominal size)
16Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement : 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement. a. M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size).
17Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement :3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a. M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size).
18Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)
19Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size)
20Centring and shuttering including strutting, propping etc. and removal of form work for: Foundation, footings, bases of columns etc. and mass concrete.
21Centring and shuttering including strutting, propping etc. and removal of form work for: Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5m height)
22Centring and shuttering including strutting, propping etc. and removal of form work for: Lintels, beams, girders, bressumers and cantilevers etc.
23Centring and shuttering including strutting, propping etc. and removal of form work for: Column, pillars, posts and struts etc.
24Centring and shuttering including strutting, propping etc. and removal of form work for: Stairs (excluding-Landings)----Waist slabs
25STEEL REINFORCEMENT
26Reinforcement of RCC work including bending, binding and placing in position complete. b) Tar/ TMT steel
27BRICK WORK
28Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).
29Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.
30Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement: 4 coarse sand) in foundation and plinth.
31ROOFING AND TERRACING
32Grading Roof for water proofing treatment with:Cement Mortar 1:3 (1 cement :3 coarse sand)
33Providing gola 75 x 75 mm in cement concrete 1:2;4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1 : 3 ( 1 cement : 3 fine sand) as per standard design :
34Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown or/ and residual bitumen applied hot @ 1.45kg per sqm. of area for each courese, second course of roofing felt type-3 grade-1 (hessian base self finished bitumen felt) and fourth and final course of stone grit 6mm and down size or pea size gravel spread at 6 Cu.dm. per sqm. including preparation of surface excluding grading complete.
35Providing and fixing on wall face C.I Rain water pipes including filling the joints with spun yarn soaked in neat cement slurry & cement mortar 1:2. 100 mm diameter
36Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10mm x 10cm x 10cm of 1:2:4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. 100 mm diameter
37Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) b)- CI Plain Bend-100mm dia
38Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) b)- CI Plain shoe-100mm dia
39Making khurras 45 x 45 cm with avg. minimum thickness of 5 cm cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 mm x 1 m x 400 micron, finished with 12 mm cement plaster 1 : 3 ( 1 cement : 3 coarse sand) and finishing the outlet complete as per drawing.Making khurras 45 x 45 cm with avg. minimum thickness of 5 cm cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 mm x 1 m x 400 micron, finished with 12 mm cement plaster 1 : 3 ( 1 cement : 3 coarse sand) and finishing the outlet complete as per drawing.
40WOOD WORK
41Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. a) 40mm thick including anodized aluminum butt hinges with necessary screws.
42Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).
43Providing and fixing aluminum handles anodised transparent or dyed to required color or shade with necessary screws etc complete. 125 mm
44Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.a) 300 x 10 mm
45Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.a) 300 x 16 mm
46Providing and fixing 50 cm long aluminum kicking plate 100x3.15mm anodised, transparent or dyed to required color or shade with necessary screws etc. complete.
47Providing and fixing chromium plated finished 100mm mortice latch and lock with 6 levers and a pair of CP handles with necessary screws etc.
48Providing and fixing MS Round or Sq bars at required spacing in wooden frames of windows.
49. FLOORING
50Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 60x60 cm refer carpet area calculation
51SKIRTING/ DADO : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 12mm thick cement mortar 1:3 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.size of tile 600x600 mm
52Providing and fixing 1 st quality ceramic glazed wall tiles confirming to IS: 15622 ( thickness to be specified by manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any sizes as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 Cement : 3 Coarse sand) and joining with grey cement slurry @3.30kg per sqm including pointing with white cement mixed with pigment of matching shade complete.
53Providing and laying rectified Glazed Ceramic floor tiles of size 300x30mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to IS : 15622, of approved make, in all colours, shades except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. sqm 1225.10 shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.
54Providing and laying gang saw cut 18 mm thick, mirror polished premoulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge.With granite stone of area less than 0.50 sqm
55. STEEL WORK
56Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a approved steel priming coat using structural steel as required in gratings, frames, guard bars, railings, brackets, gates, grills etc.
57Providing & fixing Hand Rail of approved size by welding etc to steel ladder railing, balcony railing, staircase railing & similar works, including applyingnpriming coat of approved steel primer : E.R.W Tube
58Door /Window / Ventilator Frames:- Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer- in-charge
59. FINISHING
6012 mm thk cement plaster 1: 4( 1 cement : 4 coarse sand) on walls.
6115 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement :4 fine sand)
62Applying one coat of cement primer of approved brand and manufacture on wall surface.
63Finishing walls with water proofing cement paint of required shade :
64Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.
65Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.
66With ready mixed pink primer of approved brand and manufacture on resinous wood and plywood works.
67painting with synthetic enamel paint of approved brand and manufacture to give an even shade- 2 or more coats
68Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with aluminum paint of approved quality over a priming coat of ready mixed genuine red lead on new work.
6920. ALUMINUM WORK
70Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) :Anodised Aluminium (anodised transparant or dyed to required shade according to IS:1868, minimum anodic coating of grade SC-15)
71Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beadingshall be paid in basic item)With float glass panes of 5.5 mm thickness.
72Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-inchargecomplete.255 X 19 mm.
73Septic tank
74Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30cm size, saturated soil and rock), lift upto 1.50m and stacking the excavated soil not more than 3m clear from the edge of the excavation and returing the stacked soil in 15cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. By Manual means:-a) In area of light jungle
75Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30cm size, saturated soil and rock), lift upto 1.50m and stacking the excavated soil not more than 3m clear from the edge of the excavation and returing the stacked soil in 15cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.
76Dry stone pitching 22.50 cm thick including supply of stone and preparing surface complete (including carriage of stone for 5 Km lead).
77Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :a) Foundations and plinth
78Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface with M20 (1:1.5:3 20 mm nominal size)
79Centring and shuttering including strutting, propping etc and removal of form work for :d) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
80Reinforcement of RCC work including bending, binding and placing in position complete.a) Cold twisted bars.
81Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).
8212 mm cement plaster 1 : 3 (1 cement : 3 fine sand). In Plinth wall.
83Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 150 mm dia SW pipes
84Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 150 mm dia SW pipes
85Construction of soak pit 1.5 x 1.2 x 1.5 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.
86Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).b) 20 mm nominal bore
87Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).a) 32 mm niminal bore
88Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work) b) 20 mm nominal bore
89Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work) c) 25 mm nominal bore
90providing and fixing PVC trap of approved quality.a) 50 mm
91Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain and brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement trenching, refilling & testing of joints complete as per direction of Engineer Incharge.a) External worki) 50 mm dia
92ii) 75 mm dia
93Providing & fixing steel nahani trap floor drain for WC
94Providing & fixing PVC elbow for PVC pipe fitting.
95Providing and fixing sand cast iron soil, waste and vent pipe.b) 75 mm dia
96Sanitary and Plumber works
97Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid,10 litre low level white vitreous china flushing cistern & C.P flush bend with fitting & C.I brackets,40mm flush bend,overflow arrangement with special of standard make and mosquito proof coupling of approved municipal design complete including painting of fitting and bracketss,cutting and making good the walls and floors wherever required.W.C pan with ISI marked white solid plastic seat and lid.
98Providing and fixing white vitreous china wash basin with C.I./M.S. brackets, 15 mm CP brass pillar taps, 32 mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :Flat back wash basin size 550x450 mm with a single 15 mm CP pillar tap
99Providing and fixing Stainless steel A ISI 304(18/8) Kitchen sink as per IS:13983 with CI Brackets and stainless steel plugs 40mm, including painting of fittings and brackets, cutting & making good the walls where ever required.Kitchen sink with drainboard, 510 x 1040mm with bowl depth 250mm
100Providing and fixing CP Brass Waste for wash basin and sinks.40mm dia
101Providing and fixing MI fisher union for wash basin and sinks.40mm dia
102Providing and fixing CP Brass or MI trap for wash basin and sinks.b) 40 mm dia
103Providing and fixing rubber plug for sink or wash basin.
104Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with CP brass screws and washers.
105Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.100 mm dia
106Providing and fixing sand cast iron heel rest sanitary bend.100 mm
107Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 x100x100 mm
108Providing and fixing sand cast iron trap of self cleaning design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.a) 100 mm inlet and 100 mm outlet
109Painting sand cast iron soil spun soil waste vent pipes and fittings with paint of any color such as chocolate, grey or buff etc over a coat of primer (of approved quality) for new work.100 mm diameter pipe
110G I Pipes and Fittings
111Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good the walls etc. (internal work)20 mm dia nominal bore
112Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good the walls etc. (internal work 25 mm dia nominal bore
113Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wall 20 mm dia nominal bore
114Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wal 25 mm dia nominal bore
115Providing and fixing brass full way valve with wheel of approved quality.32 mm nominal bore
116Providing and fixing brass stop cock of approved quality complete25 mm nominal bore
117Providing and placing on terrace ( at all floor levels ) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
118Providing and fixing CP brass bib cock of approved quality conforming to IS : 893120 mm Nominal bore
119Providing and fixing ball valve (brass) of approved quality.High or Low presssure with polythelene float : 20 mm Nominal bore
120Providing and fixing CP Angle Valve for basin mixtures and geysers points EWC Cisterns of approved quality conforming to IS : 8931
121Drainage System
122Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.150mm diameter
123Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.250mm
124Constructing brick masonry manhole with 2nd class bricks in cement mortar 1: 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).
125Providing and fixing square mouth SW gully trap class SP-1 complete with CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. as per standard design.180x150mm size P typeWith common burnt clay FPS(non modular) bricks of class designation 7.5. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 54727915
AUTHORITY Government Departments
TENDER VALUE Ref. Documents
LAST DATE 24-03-2026
Authority
Authority Name Public Works Department
Work Description Tender For Construction Of Infrastructure Development Of Govt.Sec. School Tai,Leparada District
Basic Detail
Tender No BD/BLDG/2025-26/04
Bidding Type Tender
Location
City Leparada
State Arunachal Pradesh
Key Dates
Publish Date 18 Mar 2026
Submission Date 24 Mar 2026
Open Date 24 Mar 2026
Finance
Tender Value Ref. Documents
Tender Fee 1000
EMD 1.75 Lakhs
Exemption Not Available
Document List
BOQ_3377.xls
d52bbe8c-8685-4823-91df-9387a0c4098b.html
TAI_TENDER_DOCUMENTS_MARCH_26.pdf
Tendernotice_1 (1).pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Mar 18, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Mar 24, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Mar 24, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
xls

BOQ_3377.xls

html

d52bbe8c-8685-4823-91df-9387a0c4098b.html

pdf

TAI_TENDER_DOCUMENTS_MARCH_26.pdf

pdf

Tendernotice_1 (1).pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender