Tender For Construction Works Of Deep Water Rescue Training Pool Facility At Cial, Ernakulam-Kerala

TDR : 54724093

Tender Notice
BOQ

35 Days Left

Ernakulam , Kerala

Tender Brief : Tender For Construction Works Of Deep Water Rescue Training Pool Facility At Cial

Document Fees
₹ 2714 /-

EMD
₹ 700000.0 /-

Tender Value
₹ 3.47 Crore /-

Submission Date
23-04-2026

Competition Type
Indian

Bidding Type
Works

Need a Business Loan? Apply Now !


1	SH : EARTHWORK
2	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
3	Earth work in excavation by means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, dewatering, lift upto 1.5m and all leads; disposal of earth outside the periphery of the area, disposed earth to be levelled and neatly dressed as directed by the Engineer-in-Charge-All kinds of soil.
4	Providing and applying Antitermite treatment by injecting chemical emulsion Imidacloprid emulsiable concentrate 0.075 percentage for pre-constructional treatment and creating a chemical barrier as per IS 6313 (Part II) 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, etc. complete conforming to manufacturers specification and as directed by the Engineer-in-Charge. (Plinth area only to be measured for the payment )
5	Filling in plinth or trenches, under floors, foundations, in areas etc with contractors own red earth including watering, ramming consolidating and dressing, cost and conveyance of all materials,labour charges,lead,lift etc complete at all levels as directed by the Engineer-in-Charge
6	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
7	SH : PILE WORK
8	Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-35 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap,pile chipping etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note : Minimum Cement content considered in M-35 is @420kg/ cum): 500 diameter pile
9	Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-35 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap,pile chipping etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note : Minimum Cement content considered in M-35 is @420kg/ cum): 600 mm diameter piles -
10	Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-35 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap,pile chipping etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note : Minimum Cement content considered in M-35 is @420 kg/ cum): 700 mm diameter piles -
11	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile above 50 tonne and upto 100 tonne Safe capacity. For pile 500 dia Routine test (Test Load 1.5 times the Safecapacity)
12	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile above 100 tonne and upto 150 tonne Safe capacity. For pile 600 dia Routine test (Test Load 1.5 times the Safecapacity)
13	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile above 150 tonne and upto 200 tonne Safe capacity. For pile 700 dia Initial test (Test Load 2.5 times the Safecapacity)
14	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile above 150 tonne and upto 200 tonne Safe capacity. For pile 700 dia Routine test (Test Load 1.5 times the Safecapacity)
15	Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and highskill trained personal for conducting the test & submission of results,all complete as per direction of Engineer-in-charge.
16	SH : RCC WORK
17	Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-35 grade conforming to IS 456 or IS 10262 for reinforced cement concrete for pile cap, grade beam etc using coarse sand conforming to IS 383 and 20mm nominal size graded hard granite broken stones, excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in proportion of 0.5% of weight of cement (as per IS 9103)to accelerate, retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-Charge. Minimum cement content is 410Kg/m3 and additional payment will not be made for extra cement, if any.All work upto plinth level.
18	Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-35 grade conforming to IS 456 or IS 10262 for reinforced cement concrete for pile cap, grade beam etc using coarse sand conforming to IS 383 and 20mm nominal size graded hard granite broken stones, excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in proportion of 0.5% of weight of cement (as per IS 9103)to accelerate, retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-Charge. Minimum cement content is 410Kg/m3 and additional payment will not be made for extra cement, if any. All work above plinth level.
19	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding with 16 gauge GI binding wire etc complete including cost, conveyance, lead, lift of all materials for all types of RCC works as per drawing/specification and as directed by Engineer-in-Charge at all levels.Thermo-Mechanically Treated bars of grade Fe-500D or more
20	Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
21	Centering and shuttering including strutting, etc. and removal of form for: Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
22	Centering and shuttering including strutting, etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform
23	Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers
24	Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts
25	Centering and shuttering including strutting, etc. and removal of form for: Stairs, (excluding landings ) except spiral - staircases)
26	Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and walls-Under 20 cm wide
27	Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and walls-above 20 cm wide
28	Centering and shuttering including strutting, etc. and removal of form for: Arches, domes, vaults up to 6m span
29	Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
30	Extra for providing and mixing water proofing compound in cement concrete work, masonry work, plastering etc in the proportion recommended by the manufacturers including cost and conveyance of all materials, labour, curing, lead lift , etc. complete as directed by Engineer-in-Charge at all levels.
31	Providing and laying damp-proof course 50mm thick with cement concrete1:2:4 (1 cement: 2coarse sand : 4 graded stone aggregate of 20mm nominal size) including cost and conveyance of all materials,labour charges,lead,lift etc complete at all levels as directed by the Engineer- in-Charge.
32	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil as directed by the Engineer- in-Charge.
33	Extra for additional height in centering, shuttering where ever requiredwith adequate bracing, propping etc., including cost of de-shutteringand decentering at all levels, over a height of 3.5 m, for every additionalheight of 1 metre or part thereof Suspended floors, roofs, landing, beams and balconies (LVL 6.2m)
34	SH : MASONRY WORK
35	Providing and constructing solid concrete masonry M-10 grade (mix 1:3:6) (1cement: 3crusher sand: 6 6mm metal) in CM 1:6 (1cement: 6coarse sand) with solid blocks of 30x20x15cm size and approved quality including scaffolding, raking out of joints, curing, cost and conveyance of all materials, labour, lead, lift, etc. complete for all types of masonry works. For works upto plinth level, as per specifications and as directed by the Engineer-in-charge.
36	Providing and constructing Solid concrete block masonry M-10 grade (mix1:3:6) (1 cement: 3 crusher sand: 6 aggregates 6mm) in C.M1:6 (1cement, 6 crusher sand) with Solid blocks of 30x20x15 cm size and approved quality including scaffolding, raking out of joints, curing, cost and conveyance of all materials, labour, lead, lift,etc.complete for all types of masonry works in super structure above the highest plinth level upto second floor level as directed by Engineer-in-charge at all levels
37	Providing and constructing Solid concrete block masonry M-10 grade (mix1:3:6) (1 cement: 3 crusher sand: 6 aggregates 6mm) in C.M1:6 (1cement, 6 crusher sand) with Solid blocks of 30x20x15 cm size and approved quality including scaffolding, raking out of joints, curing, cost and conveyance of all materials, labour, lead, lift,etc.complete for all types of masonry works in super structure above second floor level upto v floor level as directed by Engineer-in-charge at all levels.
38	SH : JOINERY WORKS
39	Providing and fixing powder coated aluminium work for doors ,windows & partitions with extruded built up standard tubular sections /appropriate Z sections & other sections of approved make confirming to IS:733 & IS:1285 fixed with rawl plugs & screws or with fixing clips including necessary filling up of gaps at junctions, at top, bottom & sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred & jointed mechanically where ever required including cleat angle, aluminium snap beading for glazing/ panelling, cp brass/ stainless steel screws, removing the stickers clearly all complete as per architectutral drawings & directions of Engineer-in-Charge at all levels. (glazing & panelling to be paid seperately). Minimum thickness of powder coating for powder coated Aluminium shall be 50 micron.For fixed portion
40	Providing and fixing powder coated aluminium work for doors, windows & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make confirming to IS:733 & IS:1285 fixed with rawl plugs & screws or with fixing clips including necessary filling up of gaps at junctions, at top, bottom & sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred & jointed mechanically where ever required including cleat angle, aluminium snap beading for glazing/ panelling, cp brass/ stainless steel screws, removing the stickers clearly all complete as per architectutral drawings & directions of Engineer-in-Charge at all levels. (glazing & panelling to be paid seperately). Minimum thickness of powder coating for powder coated Aluminium shall be 50 micron. For shutter of doors ,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings, exhaust fan of required size, etc wherever required including the cost of PVC neoprene gasket required (fittings shall be paid for separately)
41	Providing and fixing glazing with float glass panes in aluminium doors & windows/ aluminium/ other partitions for glazed openings with PVC/ neoprene gasket etc. complete as per the architectural drawings and as directed by Engineer-in-Charge at all levels. With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
42	Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood with laminate, conforming to IS : 710
43	Extra for providing frosted glass panes 5 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. ( Area of opening for glass panes excluding portion inside rebate shall be measured).
44	Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS : 3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96kg/m³ and fixing with necessary stainless steel ball bearing hinges of size100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately). The glass shall be clear , toughened, non wired, Interlayer fire resistant of having minimum 11mm thickness o fapproved make with 120 minutes of fire resistance both Integrity & radiation control (EW=120) and minimum 20min insulation (EI=20)with symmetrical (Bi-Directional) fire protection . The glass shall be able to withstand fire attack from both side.The Glass only is having a sound reduction of 37dB and LT of 86%. Glass shall be compliant to class 2B2 category of impact resistance as per EN 12600. The glass should bemanufactured in UL & TUV audited facility and including UL-EU certification.etc all complete as per direction of Engineer-in-charge.The rate shall includes the cost and conveyance of all materials ,Fastners, labour charges,lead,lift and necessary fire rated hardware like SS ball bearing hinges - Minimum 05 Nos.in each panel, Hydraulic door closer ( 1 No per each panel) ,mortise sash lock with SS liver handles 80mm (1 Set for each panel) side key operation,Concealed Flush Bolt as required,fire seal ,smoke seal etc. complete as directed by the Engineer-in-Charge at all levels. All SS fixtures shall be of 304 grade unless otherwise mentioned
45	Providing and fixing carbon steel galvanised (minimum coating 5micron) dash fastener of 10mm dia double threaded 6.8grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide P A 6 grade sleeve, including drilling of hole in frame, concrete/ masonry/ MS section, etc. as per direction of Engineer-in-charge. 10x 160 mm
46	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with arm (having brand logo with ISI, IS:3564, embossed on the body, door weight upto 100kg), with necessary accessories like SS 304 grade plate and screws etc, including cost and conveyance of all materials, labour charges, lead, lift etc complete as directed by the Engineer-in Charge at all levels. (The purchase price considered for door closer is Rs.1702/ no excluding GST and any deviation plus or minus in the purchase price will be adjusted (paid extra or deducted)while making payment to the contractor).
47	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in- charge.
48	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in charge (Door handle, lock and stopper etc.to be paid separately).
49	SH : FLOORING WORK
50	Providing and laying full body vitrified antiskid tile flooring matte finish 600x600 mm, 9- 10 mm thick with water absorbtion less than 0.08% of first quality confirming to IS:15622 with abrasion resistance less than 144 cubic mm, breaking strength greater than or equal to 2200N, which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges, lead, lift, curing, cleaning and clearing the debris from all levels and disposing etc, complete and tile protection till handover as directed by Engineer-in-Charge at all levels. The purchase price( excluding GST ) of Polished/matte double charged vitrified tile should be taken as Rs.659/-sqm and any deviation plus or minus in the purchase price( Excluding tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor
51	Providing and laying full body vitrified antiskid tile flooring matte finish 600x600 mm, 9- 10 mm thick with water absorbtion less than 0.08% of first quality confirming to IS:15622 with abrasion resistance less than 144 cubic mm, breaking strength greater than or equal to 2200N, which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges, lead, lift, curing, cleaning and clearing the debris from all levels and disposing etc, complete and tile protection till handover as directed by Engineer-in-Charge at all levels. The purchase price( excluding GST ) of Polished/matte double charged vitrified tile should be taken as Rs.904/-sqm and any deviation plus or minus in the purchase price( Excluding tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor
52	Providing and laying full body vitrified tile skirting/dadoing of range 600 x 600 mm , 9.0- 10 mm thick with water absorbtion less than 0.08% of first quality confirming to IS:15622 with abrasion resistance less than 144 cubic mm, breaking strength greater than or equal to 2200N, which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 ,including cost and conveyance of all materials, labour charges,lead, lift, curing, cleaning and clearing the debris from all levels and disposing etc, complete and tile protection till handover as directed by Engineer-in-Charge at all levels.
53	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick (Cl.11.26.1)
54	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete
55	Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge: (Cl.11.53)
56	Providing and laying full body vitrified antiskid tile flooring matte finish 24.4cm x11.9cm - Antislip tile with water absorbtion less than 0.08% of first quality confirming to IS:15622 with abrasion resistance less than 144 cubic mm, breaking strength greater than or equal to 2200N, which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges, lead, lift, curing, cleaning and clearing the debris from all levels and disposing etc, complete and tile protection till handover as directed by Engineer-in-Charge at all levels The purchase price( excluding GST ) of Polished/matte ful body vitrified tile should be taken as Rs.1120/-sqm and any deviation plus or minus in the purchase price( Excluding tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor
57	SH : FINISHING WORKS
58	12 mm cement plaster to ceiling of mix 1:3 (1 Cement : 3fine sand) including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. 13.1.2 1:6 (1 cement: 6 fine sand) at all levels
59	6 mm cement plaster to ceiling of mix 1:3 (1 Cement : 3fine sand) including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. 12 mm cement plaster of mix :13.1.1 1:4 (1 cement: 4 fine sand) at all levels
60	15mm cement plaster of mix, 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement 2 kg/sqm including mixing water proofing material in separately).proportion recommended by manufacturer at all heights including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer in charge at all levels. (water proofing liquid will be paid separately)
61	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade for new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). including cost and conveyance of all materials, labour charges, scaffoldings etc complete as directed by the Engineer in Charge at all levels.
62	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer )
63	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.
64	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
65	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.on steel works
66	SH : WATERPROOFING AND MISCELLANEOUS WORK
67	Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatiouswaterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge
68	Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomericwaterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete inall respect as per the direction of Engineer-in-Charge
69	Providing and fixing CI manhole cover with frame 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg in concrete slab over manholes /Inspection Chambers /Drains, including cost and conveyance of all materials, all labour charges, lead, lift, sundries, etc., complete. as directed by the Engineer- in-Charge
70	Supplying and installing readymade RCC hydrolic septic tank of size 2.7M (L)x1 M dia (2000L), this works includes all materials charges, transportaion, installation charges, etc complete all as per direction of Engineer in charge.
71	Supplying and installing readymade RCC (Heavy model) Hydrolic soak pit of size 0.85M (dia) x1 M (H) ,this works includes all materials charges,transportaion, installation charges, etc complete all as per direction of Engineer in charge.
72	Providing and filling soak pit with brickbats including brick chamber with dry joints etc complete as per standard design and drawing and as directed by the Engineer in charge.
73	Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:
74	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
75	Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.
76	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
77	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete
78	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc
79	SH : WATER SUPPLY AND SANITARY
80	Providing & fixing of star white vitreous China European wall hung pan with soft close seat and lid with CP brass hinges and rubber buffers with concealed cistern dual flush 3/9 litre water storage with chrome finish wall plate actuator of approved make and model complete including cost and conveyance of all materials, labour charges, lead lift, cutting, making good the walls, floors, slab wherever required testing and commissioning to the satisfaction of Engineer in Charge as per direction of Engineer-In charge at all levels. (The purchase price (Exclusive of all taxes) of WC pan with soft close seat and lid including all accessories shall be taken as Rs7642/-and concealed cistern, wall plate with flush button shall be Rs 9401/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted)while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5years and only skilled and experienced persons shall be employed for this purpose.
81	Providing & fixing of star white vitreous china under counter wash basin of approved size, CP brass waste assembly, CP brass bottle trap with extension piece 450 mm long connections pipes wall flanges and rubber adapters for waste connection, angle valve, pressmatic pillar cock, complete including CI/MS brackets duly painted, nuts, washers, etc. The rate is including cost and conveyance of all materials, labour charges, lead.lift, cutting, making good the walls, floors, slab wherever required, testing and commissioning to the satisfaction of Engineer in Charge as per direction of Engineer-In charge at all levels.(The purchase price (exclusive of all taxes) of under counter WB is Rs1913/- ., pillar cock pressmatic- Rs1976/ ,angle valve-Rs.1080/-., bottle trap-Rs .1573/-.,waste coupling Rs-.510/-.. and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted)while making payment to the contractor).The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.
82	Providing and fixing CP brass hand spray with lever control (health faucet) of make 1 meter long flexible tube and wall hook, CP brass angle valve and all fittings and fixtures of approved make etc complete including cutting and making good the walls, floors,slab wherever required. The rate is including cost and conveyance of all materials, labour charges, lead lift etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels.(The purchase price exclusive of all taxes)of CP brass hand spray with lever control is Rs.1466/-., angle valve-Rs .1080./-and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and
83	Providing and fixing CP brass long body bib cock of approved quality and make conforming to IS standards and weighing not less than 690 gms including cost and conveyance of all materials, labour charges, sundries, lead, lift, cutting and making good the walls, floors, slab etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels. (The purchase price (exclusive of all taxes)CP brass long body bib cock is Rs..927/- ..and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose. 15 mm nominal bore
84	Providing and fixing frameless mirror of thickness 5.5 to 6mm, with all four edges machine polished/ bevelled and back side protected with safety film and 4 mm thick BWP grade Plywood backing and fixed on walls with mirror screws (spacer). The rate is including cost and conveyance of all materials, labour charges, lead, lift ,cutting and making good the walls, floors, slab etc complete as directed by the Engineer-in-Charge at all levels.
85	Providing and fixing floor trap of 110mm outer dia (multitrap) including SS cockroach free floor grating concealed type with cup etc including cost and conveyance of all materials labour charges, lead, lift, cutting and making good the walls and floors etc complete as directed by the Engineer-in-Charge at all levels..(The purchase price exclusive of all taxes) cockroach trap with floor gratings Rs .1188/-.. and pvc multi floor trap is Rs..279/-and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).
86	Providing and fixing C P brass soap dish with holder of approved quality and make including cost and conveyance of all materials labour charges, lead, lift, cutting and making good the walls and floors etc complete as directed by the Engineer in Charge at all levels.(The purchase price (exclusive of all taxes) of CP brass soap dish is Rs.1050/-.and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted)while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.
87	Providing and fixing under counter mounting pressmatic/ automatic liquid soap dispenser of approved make including cost and conveyanceof all materials labour charges, lead, lift, cutting and making good the walls, floors and slab wherever required etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in Charge at all levels.(The purchase price (exclusive of all taxes) of under counter mounting pressmatic/ automatic liquid soap dispenser is Rs.5525/-. and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.
88	Providing and fixing CP towel rail 600 mm of approved make complete with brackets fixed using wooden cleats with CP Brass screws etc complete. The rate is including cost and conveyance of all materials, labour charges, lead, lift, cutting and making good the walls, floors etc complete as directed by the Engineer in charge at all levels. (The purchase price (exclusive of all taxes) of CP towel rail is Rs .1211/-.and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.
89	Providing and fixing premium quality shower set consisting of overhead shower (square shape) single flow(body and face plate stainless steel) and hand shower oval shape single flow (stainless steel Body and face plate)bathspout with single lever divertor with wall flange of approved make and model including cost and conveyance of all materials, labour charges, lead, lift etc.,complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer-in-Charge at all levels. (The purchase price excluding tax considered all accessories for over head shower and arm is Rs.6273/- for hand shower-Rs 3272, for bath spout and divertor-Rs 6791/ including all accessories any deviation plus or minus in the purchase price will be adjusted (will be paid extra or deducted) while making payment to the contractor)
90	Providing and fixing CP brass robe hook of approved make. The rate is including cost and conveyance of all materials, labour charges, sundries, cutting and making good the walls and floors wherever required etc complete as directed by the Engineer in charge (The purchase price(exclusive of all taxes) of robe hook is Rs.603/-.and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor)
91	Providing and fixing sanitary fixtures for handicapped toilet including one wash basin of approved size, one pair mounting brackets and all other related CP brass fittings like health faucet, angle valves,pillar cock, bottle trap,angle valve,waste coupling etc.One number EWC & Cistern with raised soft push button for convenient access complete with fittings & seat cover , one no.stainless steel hinged rail 76 cm & five nos. of stainless steel grab rails 60 cm and one no.of Faucet with spatula lever etc of approved make as per drawing & as per manufactures specification . The rate is including cost and conveyance of all materials, labour charges, lead,lift,cutting and making good the walls,floors,slab wherever required etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels. ( Ref Model no: Hindware-70002(Handicapped Toilet Matrix)
92	Providing and fixing paper holder of approved make. The rate is including cost and conveyance of all materials, labour charges, sundries, cutting and making good the walls and floors wherever required etc complete as directed by the Engineer in charge
93	SH : INTERNAL AND EXTERNAL SANITARY
94	Providing and fixing cleanout 110mm Dia including cost and conveyance of all materials labour charges, lead, lift, cutting and making good the walls and floors etc complete testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in Charge at all levels.(The purchase price (exclusive of all taxes) cleanout Rs .552/-. and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor).
95	Providing and fixing cleanout 75mm Dia including cost and conveyance of all materials labour charges, lead, lift, cutting and making good the walls and floors etc complete testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in Charge at all levels.(The purchase price(exclusive of all taxes) cleanout Rs .498/-. and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted)while making payment to the contractor).
96	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc. with clamps including cutting and making good the walls,testing the lines rectifying any leakages or defects,etc. complete for soil, waste, rainwater,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for concealed work as directed by the Engineer-in Charge. 110mm OD (6 kg/cm2)
97	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc. with clamps including cutting and making good the walls,testing the lines rectifying any leakages or defects,etc. complete for soil, waste, rainwater,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for concealed work as directed by the Engineer-in Charge. 75mm OD (6 kg/cm2)
98	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc. with clamps including cutting and making good the walls,testing the lines rectifying any leakages or defects,etc. complete for soil, waste, rainwater,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for concealed work as directed by the Engineer-in Charge. 50mm OD (6 kg/cm2)
99	Providing and fixing PVC vent cowl to pipe already fixed as directed by Engineer-in-Charge at all levels.75 mm dia
100	Providing and fixing PVC vent cowl to pipe already fixed as directed by Engineer-in-Charge at all levels.110mm dia
101	Providing and fixing PVC vent cowl to pipe already fixed as directed by Engineer-in-Charge at all levels.160 mm dia
102	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bends, door tees, elbows, unions, etc. with clamps including earth work, refilling, testing the lines rectifying any leakages or defects, etc., complete as directed by the Engineer-in-charge for soil, waste, rainwater pipe, etc. for underground lines. 160mm dia (6 kg/cm2)
103	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bends, door tees, elbows, unions, etc. with clamps including earth work, refilling, testing the lines rectifying any leakages or defects, etc., complete as directed by the Engineer-in-charge for soil, waste, rainwater pipe, etc. for underground lines. 110mm dia (6 kg/cm2)
104	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bends, door tees, elbows, unions, etc. with clamps including earth work, refilling, testing the lines rectifying any leakages or defects, etc., complete as directed by the Engineer-in-charge for soil, waste, rainwater pipe, etc. for underground lines. 75mm dia (6 kg/cm2)
105	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bends, door tees, elbows, unions, etc. with clamps including earth work, refilling, testing the lines rectifying any leakages or defects, etc., complete as directed by the Engineer-in-charge for soil, waste, rainwater pipe, etc. for underground lines. 50mm dia (6 kg/cm2)
106	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc.with clamps testing the lines rectifying any leakages or defects, etc.complete as directed by the Engineer-in Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for internal work-exposed on walls as directed by the Engineer in charge.110mm dia (6 kg/cm2)
107	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc.with clamps testing the lines rectifying any leakages or defects, etc.complete as directed by the Engineer-in Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for internal work-exposed on walls as directed by the Engineer in charge.75mm dia (6 kg/cm2)
108	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc.with clamps testing the lines rectifying any leakages or defects, etc.complete as directed by the Engineer-in Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for internal work-exposed on walls as directed by the Engineer in charge.50mm dia (6 kg/cm2)
109	Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows, unions, etc.with clamps testing the lines rectifying any leakages or defects, etc.complete as directed by the Engineer-in Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for internal work-exposed on walls as directed by the Engineer in charge.75mm dia (6 kg/cm2)
110	SH : INTERNAL AND EXTERNAL WATER SUPPLY
111	Providing and fixing C.P. brass concealed stop cock (control valve) of standard design and of approved make conforming to IS:8931. The rate is including cost and conveyance of all materials, labour charges, lead, lift, cutting and making good the walls, floors, slab etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels. (The purchase price (exclusive of all taxes)of C.P. brass concealed stop cock (control valve) is Rs..1593/-. and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose. 15mm nominal bore
112	Providing and fixing brass ball valve conforming to IS standards including cost and conveyance of all materials, labour charges, sundries, cutting and making good the walls, floors, slab etc complete as directed by the Engineer-in-Charge at all levels 65 mm dia nominal bore
113	Providing and fixing brass ball valve conforming to IS standards including cost and conveyance of all materials, labour charges, sundries, cutting and making good the walls, floors, slab etc complete as directed by the Engineer-in-Charge at all levels 50 mm dia nominal bore
114	Providing and fixing brass ball valve conforming to IS standards including cost and conveyance of all materials, labour charges, sundries, cutting and making good the walls, floors, slab etc complete as directed by the Engineer-in-Charge at all levels 40 mm dia nominal bore
115	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 65 mm nominal outer dia pipes
116	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 50 mm nominal outer dia pipes
117	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 40 mm nominal outer dia pipes
118	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 32 mm nominal outer dia pipes
119	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 25mm nominal outer dia pipes
120	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 20 mm nominal outer dia pipes
121	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC SDR11) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall- 15 mm nominal outer dia pipes
122	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 65mm OD
123	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 50mm OD
124	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 45mm OD
125	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 32mm OD
126	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 25mm OD
127	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. The rate is including cost and conveyance of all materials, labour charges, sundries, lead, lift, all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc). 20mm OD
128	Supplying, fixing, jointing, testing and commissioning to satisfaction of Engineer in charge of schedule 80 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions, bends, sockets bends, flanges, reducers, endcaps, saddles, plugs, coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers, ferrule, pipesupports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc. hire of tools and plant,trenching and refilling, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure, rectifying any leakage or defects etc. complete. as directed by Engineer-in-Charge for water supply. 65 mm dia ID
129	Supplying, fixing, jointing, testing and commissioning to satisfaction of Engineer in charge of schedule 80 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions, bends, sockets bends, flanges, reducers, endcaps, saddles, plugs, coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers, ferrule, pipesupports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc. hire of tools and plant,trenching and refilling, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure, rectifying any leakage or defects etc. complete. as directed by Engineer-in-Charge for water supply. 50 mm dia ID
130	Supplying, fixing, jointing, testing and commissioning to satisfaction of Engineer in charge of schedule 80 UPVC ASTM pipe and Schedule 80 ASTM-UPVC specials of approved make such as tees elbows, unions, bends, sockets bends, flanges, reducers, endcaps, saddles, plugs, coupling, etc. including cost of all jointing materials like solvent cement, bolts, nuts, rubber washers, ferrule, pipesupports, cost of extra wastage of fittings during laying of pipe line such as rectification and recharging of the existing line as and when required etc. hire of tools and plant,trenching and refilling, cost and conveyance of water for testing after connecting to mains including all testing pipe line to the specified hydrostatic test pressure, rectifying any leakage or defects etc. complete. as directed by Engineer-in-Charge for water supply. 40 mm dia ID
131	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer- in-Charge. External work- 50 mm nominal outer dia pipes
132	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer- in-Charge. External work- 62.5 mm nominal outer dia pipes
133	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 65 mm dia nominal bore
134	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 50 mm dia nominal bore
135	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 40 mm dia nominal bore
136	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 32 mm dia nominal bore
137	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 25 mm dia nominal bore
138	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I.Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 20 mm dia nominal bore
139	Providing and fixing gun metal non-return valve of approved quality (screwed end): 50 mm nominal bore Horizontal
140	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of CI Gratings of approved quality including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 150x150 mm
141	Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of CI Gratings of approved quality including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels 180x180 mm
142	Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials, labour charges, making good the walls etc complete as directed by the Engineer in Charge. 50mm
143	Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials, labour charges, making good the walls etc complete as directed by the Engineer in Charge. 40mm
144	Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials, labour charges, making good the walls etc complete as directed by the Engineer in Charge. 65mm
145	Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials, labour charges, making good the walls etc complete as directed by the Engineer in Charge. 200mm
146	Supplying and fixing of centrifugal pump, with CI construction, CI impeller, mechanical seal, complete with motor, base plate, foundation bolts, nuts, pressure guage and all accessories. and working with 415V, 3ph and 50 Hz frequency including cost and conveyance of all materials, labour charges etc complete as directed by the Engineer in charge at all levels Capacity: 7m3/hr @ Head: 18m.
147	Supplying and fixing of Pressure Boosting water transfer pump at roof top with CI casing, SS impeller, mechanical seal, complete with motor, base plate, foundation bolts, nuts ,pressure guage and all accessories. and working with 230V, single phase and 50 Hz frequency including cost and conveyanceof all materials, labour charges etc complete as directed by the Engineer in charge, Capacity : 1HP
148	SH : SWIMMING CUM DEEP POOL WORKS; Design, Supply and Installation of swimming pool MEP Equipments .This has reference to the discussion, regarding the Overflow Type pool for the above project; we are pleased to offer the following equipment. Common filtrationsystem for Diving Pool Size ( 7.50 x 6.00 x 6.00 mtr) Main Pool: (19.00 x 7.50 x 1.35 Average depth)Total Volume of water - 486m3Turn over period - 4.05hrsDesigned Flowrate - 120m3/hr
149	Filtration And MEP System : Design, engineering, supply, installation, testing and commissioning of complete skimmer type deep diving swimming pool filtration and MEP system for the specified deep diving pool, designed for a maximum filtration cycle of 4 hours, including complete CPVC piping system for suction, return, backwash and drain lines with all necessary valves, fittings, supports and accessories; high-efficiency filtration system comprising bobbin wound sand filters or membrane filters or a suitable combination thereof, including circulation pumps, strainers, semi-automatic backwashing arrangement, chemical dosing system for disinfection and pH control, instrumentation, gauges, flow meters and control panels; foundations / mounting arrangements for filters, pumps, dosing units and allied equipment; skimmers, main drains, return inlets and all hydraulic fittings required for proper circulation and treatment of pool water; underwater LED pool lighting system with cabling, earthing and control panels, SS 304/316 pool ladders, poolside fittings including floating lanes and safety accessories; pool cleaning and maintenance equipment such as vacuum system, telescopic poles, brushes, leaf skimmers, suction heads and related accessories, all complete. The scope shall also include all underwater lights, inlets, drains, skimmers and embedded fittings compatible with membrane liner type pool finishing system (PVC membrane liner in lieu of tiles) including flanges, gaskets and watertight sealing arrangements. The pool water treatment system shall be designed to maintain water quality in accordance with the requirements of IS 3328:1993 or latest revisions, and design, safety, operation, and maintenance as per IS 16508:2017 or latest revisions, including all necessary equipment and operational provisions to achieve the prescribed standards. The work shall include complete electrical works including SITC of necessary panels for filter pumps, cabling / wiring from the panels to pump systems, testing, commissioning, trial run, performance demonstration and handing over, including all consumables, accessories and allied works required for making the system fully functional, complete as per specifications and drawings and as directed by the Engineer-in-Charge.
150	Providing and fixing Reinforced PVC Liner (checkered high-tech embossed) of minimum thickness of 1.5 mm in approved shades of blue colour, including the cost of liner, liner locks, necessary accessories, labour charges, fixing, laying, welding/jointing, and installation complete, including conveyance of all materials, lead, lift, and all incidental charges, complete as directed by the Engineer-in-Charge at all levels.
151	SH : TOILET CUBICLE
152	CUBICLE ZMS BLACK 2003MM-Providing and fixing 12 mm compact laminate, floor mounted Modular Toilet cubicles of approved size , make and Model . Approximate size of cubicle of approved size including bottom gap of 150 mm and approximate door size 600mm (W) X 1830mm (H) using 12 mm thick Compact Laminate of approved colour and finish,SS 316 grade Shoe legs as per manufacturer specifications, SS Gravity hingeswith cover (Right /Left) ,SS Coat Hook with door Stopper,SS Door Knob, SS Lockset with indicator, SS U and F channel ,SS door stopper channels, SS top rails, SS Screws & Wall Plugs etc.The rate is Inclusive of cost,carriage of all materials, labour charge, lead & lift, etc complete as directed by Engineer-in-Charge at all levels. The rate includes cutting the sharp edges of compact laminate with specialised machinery,additional frame work for suit the ledge wall etc,cutting and making good the wall/floor etc wherever required .The above work shall be carried out by an agency having sufficient experience in similar work and only skilled and experienced persons shall be employed for this purpose.
153	SH : ELECTRICAL WORKS- Providing. fixing, testing and commissioning complete including supply of all materials, labour, accessories, conduits, junction boxes, wiring, cutting and making good the walls etc. complete as directed by the Engineer in charge.
154	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable as required. Group C
155	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C
156	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire
157	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
158	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq.mm earth wire
159	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm
160	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch
161	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch
162	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet
163	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet
164	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet
165	Supply and fixing of following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. RJ 45 Socket Outlet
166	Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness
167	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
168	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
169	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)
170	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)
171	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)
172	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)
173	Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required
174	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door
175	MAIN SWITCH BOARD (MSB) : Supply, Installation, Testing & Commissioning of LT Main switch board cubicle made out of 2mm thick CRCA sheet, totally enclosed, IP 42, Wall/floor mounting as per the requirement, dust and vermin proof, indoor, compartmentalised, suitable for operation on 3 phase , 415 V, 50Hz AC system with busbars , including internal wiring with suitable size HFFR wires/cable, interconnection, duly powder coated with seven tank process etc.The panel shall be fabricated from a firm having CPRI certification with test certificates for similar panel (required for short circuit rating, temperature rise and IP classification) and with following switchgears, metering instruments and accessories etc. complete as required as per drawing & specification. The Panel shall be suitable for top entry & exit cables.Incomers:125 A 25 kA, FP Microprocessor based Moulded Case Circuit Breaker-1 No Type 1+2 SPD -1 no. Bus Bar: TPN bus bar chamber with 125 A, 25 kA Aluminium bus bar (P=N) + Cu earth bus. Instruments:Multifunction Meter, control MCB Indication Lamps,CTs as per SLD,ON/OFF/TRIP indication Lamps Out goings: 63 TPN MCB-2 no. 40A TPN MCB-2 nos. spare- 2 No. General danger notice board/Name plates shall be provided.
176	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (butwithout MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door
177	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole
178	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole
179	Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
180	Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required - 25 amps
181	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc as required - 25 amps
182	Supply, Installation, Testing and Commissioning of 250mm sweep Light Duty Exhaust fan in plastic body with self opening louvers working on 230 V single phase A/C.
183	Supply, Installation, Testing and Commissioning of 380 mm sweep, 900 rpm Heavy Duty Exhaust fan with louvered shutter working on 230 V A/C supply.
184	Supplying and fixing of modular type 32 A DP switch with indicator on the existing modular plate & switch box including connections etc. as required.
185	Supply, Installation, Testing & Commissioning of 400mm sweep 5 star rated BLDC Wall mounting oscillating type fan of approved make with remote control including all accessories of approved make as required for use on 240V AC supply.
186	Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required. 1200mm sweep -5star rated BLDC ceiling fan of approved make without remote control complete with 300mm down rod , canopies, shackles and blades working on 230V/240V single phase A/C.
187	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required Triple pole and neutral
188	Supplying and fixing of 40 A to 63A rating, 415V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple Pole Neutral
189	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
190	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required - 63 amps
191	Supply, Installation, Testing & commissioning of 12 W LED Rimless Round Surface Light with efficacy of minimum 100lm/W suitable for Ceiling/ Wall mounted including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required suitable for 240V AC supply.
192	Supply, Installation, Testing & commissioning of 10 W LED Bulk head fixture of approved make complete with all accessories as required suitable for 240V AC supply.
193	Supply, Installation, Testing & commissioning of 20 W LED Batten of approved make with output ofminimum 2000 lumen complete with all accessories directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required suitable for 240V AC supply.
194	Supply, Installation, Testing & commissioning of 24 W LED Rimless Round Surface Light with efficacy of minimum 100lm/W suitable for Ceiling/ Wall mounted including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required suitable for 240V AC supply.
195	Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps \\"C\\" curve, SP, MCB, in sheet steel enclosure, onsurface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required
196	Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts \\"C\\" curve DP MCB complete with connections, testing and commissioning etc. as required.
197	Supply, Installation, Testing & Commissioning of 1 HP monoblock pump with all related accessorie scomplete as instructed by engineer in charge.
198	Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.06 mm GI conductor (8 SWG)
199	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
200	Supply, Installation, Testing and Commissioning of Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers.Copper bonded rod of size (17.2mm x 2000mm) with chemical bag with all accessories.The earth rod should be properly covered with UV resistant earth pit Chamber complied to IEC62561- including boring of earth pit suitable for the earthing to be done as per the dimension of earth rod.
201	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface/ cable tray / trench as required.Upto 35 sq. mm
202	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface/ cable tray / trench as required. Above 35 sq. mm and upto 95 sq. mm
203	Supply of following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor, A2XFY power cable conforming to IS 7098.2 core 6 sq.mm
204	Supply of following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor, A2XFY power cable conforming to IS 7098.4 core 10 sq.mm
205	Supply of following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor, A2XFY power cable conforming to IS 7098.3.5 core 35 sq.mm
206	Supply of following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor, A2XFY power cable conforming to IS 7098.3.5 core 120 sq.mm
207	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm)
208	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)
209	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3.5 X 35 sq. mm (28mm)
210	Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation(during casting) for cable entry including bending the pipe to the required shape complete as required.40 mm dia
211	Supply Conveyance, installation, testing and commissioning of 100W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)
212	Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sqmm
213	Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench 50/38 mm or nearest size
214	Supply and Installation of outdoor weather proof IP66 rated Junction Box including associated accessories of approved make.
215	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)
216	SH: COMPREHENSIVE ANNUAL MAINTENANCE CONTRACT FOR A PERIOD OF 5 YEARS AFTER THE DEFECT LIABILITY PERIODComprehensive Annual Maintenance Contract (CAMC) for a period of five (5) years commencing after the successful completion of the three-year Defect Liability Period for the MEP systems of the Pool, as detailed in the clause 41, SCC.
217	4th Year
218	5th Year
219	6th Year
220	7th Year
221	8th Year Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Kerala Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Works Of Deep Water Rescue Training Pool Facility At Cial, Ernakulam-Kerala

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Works Of Deep Water Rescue Training Pool Facility At Cial, Ernakulam-Kerala

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us