|
| 1 | Earth work in excavation for all type of road structure such as retaining walls ,breast walls, culverts, drains and parapets etcetera in all type of classification of soil comprising of ordinary rock, hard rock, chiseling/ wedging out rocks (where blasting is prohibited ) as per drawing and MORT&H technical specification clause 304 and as per direction of the Engineer-in- Charge including setting out, construction of shoring and bracing removal of stumps and other deleterious materials and disposal of materials upto all leads and lift, including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm(one hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water ( surface and sub soil water) upto all depth and any quantum of water including cleaning of slush which may arise out during dewatering as per the direction of the Engineer-in- Charge including entire carriage of material with in all leads ,lifts and other incidentals . The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 2 | Providing and laying mechanically mixed and vibrated plain cement concrete nominal mix 1:4:8 (One cement : four sand : eight graded crushed stone aggregate) 20mm (twenty millimetres) nominal size on ground or under water and curing complete including pumping or bailing out water, dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights and depths including cost of form work for plain concrete in abutments foundation for all type of structures complete as per drawing and technical MORTH specification clause 1500,1700 and 2100 as per the direction of Engineer-in-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 3 | Back filling behind abutment , wing walls and return walls complete as per drawings & MORTH technical specification Clause 710.1.4 of I.R.C. 78 and 2200 granular material as per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 4 | Providing weep holes in brick/stone masonry/plain/reinforced concrete abutment , wing walls, return walls, retaining walls with 100mm (One hundred millimetre) dia AC, PVC pipe D-plast finolex/supreme having working pressure not less than 4 kgs (four kilogramme) per centimetre square pipe extending through the full width of the structures with slopes of I(V):20(H) (one vertical : twenty horizontal) towards drawing face complete as per drawing and MoRTH technical specification clause 2706 & 2200 and as per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 5 | Providing and erecting a “W” metal beam crash barrier comprising of 3mm(three millimetre) thick corrugated sheet metal beam, guard , rail 70cm(seventy centimetre) above road/ ground level, fixed on ISMC series channel vertical post 150x75x5mm(one hundred fifty into seventy five into five millimetre) thick spaced 2 mtr (two metre) center to centre 1.8mtr (one point eight metre ) high 1.1m(one point one meter) below ground/ road level all steel parts and fitments to be galvanized by hot dip process all fittings to conform to IS:1367 and IS 1364 metal beam, guard rail to be fixed on the vertical post with a spacer of channel section 150x75x5mm(one hundred fifty into seventy five into five millimetre) 330mm (three hundred thirty millimetre) long complete as per MORTH technical specification clause 811 and as per standard drawing and as desired by the Engineer-in- Charge including entire carriage of material with in all leads, lifts and other incidentals .The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 6 | Scarifying existing bituminous road surface to a depth of 50mm(fifty millimetre) by mechenical means (using Hydraulic excavator) and disposal of scarified material upto any leads and lifts as per MORT&H Technical Specification Clause 305.4.3 and as per the directions of Engineer- in- Charge including entire carriage of material in all leads and lifts . The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 7 | Providing and applying tack coat with bitumen emulsion (RS-I) using emulsion distributor at the rate of 0.275( zero point two seven five) kilogram per square metre on the prepared bituminous surface cleaned with hydraulic broom as per MORTH technical specifications clause 503 as per the direction of Engineer-in- Charge. including entire carriage of material in all leads and lifts. The rates are inclusive octrol, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 8 | Providing and laying 50mm(seventy five millimetre) thick dense graded bituminous macadam with 40-60 tonne per hour ( forty to sixty ) batch type HMP producing an average output of 75(seventy five ) tonnes per hour or any suitable capacity HMP using crushed aggregates of specified grading-II, premixed with bituminous binder and filler of specified material VG-30(Viscosity grade-thirty) @ 4.25%(four point twenty five percent) minimum by weight of mix and filler, 2% (two percent) transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH technical specification clause No. 505 complete in all respects. including entire carriage of material within all leads and lifts and other incidentials..The rates are inclusive octroi, royality,malkana ,toll tax sale tax,,GST,labour cess or other taxes imposed by the Government. |
| 9 | Providing and laying 40mm(forty millimetre) thick bituminous concrete with 100-120 TPH(one hundred to one hundred twenty tonne per hour) batch type hot mix plant producing an average out put of 75 (Seventy five) Tonne per hour using crushed aggregates of specified grading-II premixed with bituminous binder and filler of specified material VG-30 (viscosity grade-thirty ) at the rate of 5.5percent (five point five percent) minimum by weight of mix and filler, 2 percent (two percent) transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H technical specifications Clause 507 complete within all respect. as per the direction of Engineer-in- Charge. including entire carriage of material in all leads and lifts. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 10 | Providing and laying mechanical mixed and vibrated plain cement concrete 1:3:6 (one cement: three sand : six agreegate) broken /crushed stone aggregate 20mm (twenty millimeter nominal size) on ground or under water and curing complete for 14 (fourteen ) days including pumping or bailing out water, dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights and depths including cost of form work for plain concrete in open foundations for all types of structures complete as per drawing and MORT&H technical specifications section 1500, 1700 & 2100 and as per directions of Engineer- in- Charge including entire carriage of material with in all leads , lifts and other incidentals . The rates are inclusive octroi , royality , Malkana, toll tax, GST or other taxes imposed by the Government . |
| 11 | Providing and laying plain/reinforced cement concrete in foundation as per drawing and technical MORTH specification clause 1500,1700 and 2200 design mix to obtain minimum compressive strength of Grade M-30 (M-Thirty) with minimum content cement 420 kg per cubic metre(four hundred twenty kilogramme per cubic mere) using concrete mixer as per direction of Engineer-in-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 12 | Providing and laying bitumen mastic asphalt wearing course (as per specifications) with industrial bitumen of grade 85/25(eighty five/twenty five) conforming to IS : 702, prepared by using mastic cooker and laid to required level and slope, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of approved size at the rate of 0.005 cum per 10 sqm (zero point zero zero five cubic metre per ten square metre) and at approximate spacing of 10 cm(ten centimetre) centre to centre in both directions, pressed into surface protruding 1 mm to 4 mm(one millimetre to four millimetre) over mastic surface, including cleaning the surface, removal of debris etc. all complete. (25 mm(twenty five millimetre) thick ) (Considering bitumen using 10.2% (ten point two percent)as per MORTH technical specification clause 515 &2702. including carriage of material within all leads and lifts and other incidentals . The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 13 | Providing and laying Steel work of TATA/ SAIL welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etcetera as required in stringers, treads , lainding etcetera of stair case , including use of chequered plate wherever required all complete as per drawing and technical specification and as per directions of Engineer -in -Charge including entire carriage of material in all leads and lifts . The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 14 | Providing and laying mechanically mixed and vibrated plain /reinforced Cement Concrete design mix with a minimum cement contents @ 275 kg/cum(two hundred seventy five kilogramme per cubic metre) to obtain minimum compressive strength of M-15 (M- fifteen ) grade with broken/ crushed aggregate 20mm (twenty millimetre) nominal size including cost of form work, and curing complete for 14 (fourteen) days in sub structure and abutment on ground or under water and curing complete including form work with the Mild Steel Plate , including pumping or bailing out water, dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights and depths as per drawing and MORT&H technical specification clause 1500,1700 and 2100 and as per the directions of Engineer-in –charge including carriage of material within all leads and lifts and other incidentals . The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 15 | Providing and fixing ordinary kilometre stone precast re-inforced cement concrete M-15 (M-Fifteen) grade kilometre stone of standard design as per IRC 8, fixing in position including painting and printing etcetera as per drawing and MORT&H technical specification section 804 and as per directions of Engineer- in- Charge including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 16 | Providing and fixing of reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and MORT&H Technical Specification Clause 806 including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 17 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm(one point five millimetre) thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm(sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORTH for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm(forty seven into foty seven ) of 12(twelve) SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 (fifteen) grade cement concrete 450x450x600 mm(four hundred fifty into four hundred fifty into six hundred millimeter), 600 mm(six hundred millimetre) below ground level as per approved drawing MORTH technical specifications Clause 801 and as per directions of Engineer- in- Charge including entire carriage of material within all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 18 | Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm(two millimetre) thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm(seventy millimetre) width and required message, letters, figures with reflective engineering grade tape as per MORTH specifications of required shade and colour. Supported and welded on 47mm x 47 mm(forty seven into foty seven ) of 12(twelve) SWG Square tube of 3050 mm(three thousand fifty millimetre) height duly strengthened by 25 mm x 5 mm(twenty five into five millimetre) M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 (fifteen) grade cement concrete 450 mm x 450 mm x 600 mm(four hundred fifty into four hundred fifty into six hundred millimeter), 600 mm(six hundred millimetre), 600 mm below ground level as per approved drawing and MORTH technical Specification Clause 801 Direction and place indentification signs up to 0.9 sqm(zero point nine square metre) size board and as per directions of Engineer- in- Charge including entire carriage of material within all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 19 | Providing and laying of hot applied thermoplastic compound 2.5 mm (two point five millimetre) thick including reflectorising glass beads @ 250 gms (two hundred fifty grams) per sqm area, thickness of 2.5 mm (two point five millimetre) is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes as per approved drawing and MORT&H technical specifications clause 803 and as per directions of Engineer- in- Charge including entire carriage of material within all leads , lifts and other incidentals. The rates are inclusive of octroi, royality, malkana ,toll tax GST, or other taxes imposed by the Government. |
| 20 | Providing and fixing cat eye make)(3M) of size 100x20mm made of heavy duty body shall be molded dual shank ASA /Acyclic styrene acyloretrite ) or HP/High impact polystyrene) ort ABS having electronically welded micro prismatic lens with abrasion resistant coating as approved by Engineer-in-charge. The road stud shall support a load of 13635 by tested in accordance with ASTM D4280.The slope of retro reflective surface shall be 35+/-5 degrees to base. The reflective panels on both side with at least 12cm. of each area side. The luminance intensity should be as per the specification ASTM as recommended in BS-8873 part 4 1973 as per approved sample and manufacture by the Engineer-in-charge .including carriage of materail within all leads and lifts .The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 21 | Removal of earth from the choked hill side drain and disposing it on the valley side manually Hill Side Drain Clearance as per MORTH technical specifications clause 3000. including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 22 | Clearing grass and removal of rubbish up to all leads and lifts outside the periphery of the area as per MORTH technical specifications clause 201.including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 23 | Cutting of trees, including cutting of trunks, branches and removal of stumps, roots, stacking of serviceable material within all lifts and leads as per MORTH technical specifications clause 201 including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 24 | Filling Pot-holes and Patch Repairs with open-Graded Premix surfacing, 20mm.Removal of all failed material, trimming of completed excavation to provide firm vertical faces, cleaning of surface, painting of tack coat on the sides and base of excavation as per clause 503, back filling the pot holes with hot bituminous material as per clause 511, compacting, trimming and finishing the surface to form a smooth continuous surface, all as per MORTH technical specifications clause 3004.2 including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. |
| 25 | Clearance of land slides in soil and ordinary rock by a bull-dozer D 80 A-12, 180 HP and disposal of the same on the valley side as per MORTH technical specifications clause 3000 including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive octroi, royality,Malkana, toll tax, or other taxes, but excluding GST imposed by Government. Please Enable Macros to View BoQ information |
