|
| 1 | Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination on other side balancing lamination Grade I,Type II, IS : 12823 marked including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete : 18 mm thick |
| 2 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge. 0.8mm thick mica |
| 3 | Chairs :Steel pipe pedded chair |
| 4 | Providing & Fixing of IP 20 box made out from 1.2mm thick CRCA sheet steel with depth of minimun 30 mm and finished with powder coating and suitable for mounting LED tube including side covers, holders , internal wiring to illuminate the single sided connection LED tube. ( Without tube). All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Suitable for 4' LED Tube shape fixture for single rod |
| 5 | Supply & laying of 0.9 mm Teflon copper wire (Fire And Water Resistant) with sleeves ,taping including Grove cutting ,Zirri cutting in plaster stone wall ,column, roof with Scaffolding , filling chemical epoxy Araldite ,pvc clips, finished with lime mortar etc. |
| 6 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional echnical parameters of product / work refer Annexure 'A' attached with this BSR Short point (up to 3 mtr.) |
| 7 | Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer incharge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this 6 A 3/5 pin shuttered socket |
| 8 | Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer incharge, making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10 A one way switch |
| 9 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 1.5 m |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 11 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 12 | Supplying and fixing of GI chain link fencing of required width in mesh including strengthening with 2 mm dia GI wire/ G.I. staples/ G.I.U-nails/ nuts bolts with 2.4 m angle iron posts 50 mm x 50 mm x 6 mm placed every 3 metres center to center founded in M15 grade cement concrete 30cmx30cmx60cm, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only etc complete as required and as per direction of Engineer-in-charge.Mesh size 50mm x 50mm made of GI wire 3.15mm dia |
| 13 | Random rubble masonry with hard stone in foundation and plinth :Cement mortar 1:3 (1 cement : 3 coarse sand) |
| 14 | Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :Raised and cut pointing |
| 15 | Providing and laying damp-proof course with cement concrete grade M-15 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar. 50mm thick. |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 17 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). |
| 18 | Factory made PVC rigid foam sheet 5mm thick |
| 19 | Providing and installation of Poly Carbonate Sheet roofing over existing steel framing as per drawing and design including fixing with non-corrodible nuts and water proof washers as per instruction of Engineer-in-charge.6 mm thick |
| 20 | Stainless steel screws 50 mm |
| 21 | Stainless steel screws 40 mm |
| 22 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Mini stall size 455x385x350mm. |
| 23 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. |
| 24 | C.P.brass tap 15 mm |
| 25 | C.P. Brass bibcock 15 mm |
| 26 | C.P. Brass angle valve 15 mm |
| 27 | SITC of IR IP Based 5 MP Dome camera : 1/2.8\\" Progressive CMOS , ICR, IR 2560(H)X1920(V):25fps(P) , 2.8/3.6 mm lence (As per site requirement) H 264,H265/MJPEG, dual-stream, 120dB WDR or better , 3D DNR,BLC, IR: minimum 30 mtr, Provision for Support on-board storage up to 256 GB (SD card not included), intrution detection, line crossing detection Motion detection , Dynamic analysis, Alarm should br triggeron (Tampering alarm , Natwork disconnect, IP addess conflic , Storage exception ), security feature such as (password protection , privacy mask , watermark , IP address filtering, anonymouse access ), OPEN Standerd to support ONVIF (PROFILE S , PROFILE G ), Metal Housing, Vandal-proof housing IP 67, DC 12V & poE, complete with junction box for cable managment Oerating condition : 20°C -50°Cor better. Model should be : CE , BIS/UL,FCC,ROHS compliance. The CCTV OEM should have its office and survice/ support center in Rajasthan All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 28 | Supply, Installation, Testing & Commissioning of 16 ch NVR Pre-licenced, NVR support up to 40 TB HDD Support, 16 ch IP inputs; ; Support NVR technology ; 320 mbps incoming bandwidth, support up to 12 MP full channel recording ; support H.265 compression ; 16 ch syncronised playback @1080p; support 3rd party cameras ONVIF type; 4K output : minimum 04 SATA HDD Slote ; each slot should support upto 10TB HDD ; Dual gigabite self adaptive Ethernet interface ; serial interfaece ; USB interface ;(all camera and storage - NVR Should be of same make for the smooth functioning of the system ) . complete with mounting accessories & junction box (to be provided by OEM ) for cable managment. Model should be ; certificates of compliance : UL CE/FCC, BIS. The CCTV OEM should have its office and service /support center in Rajasthan All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 29 | Supply, Instalation, Testing & Communicationing of 3.5\\" 6 TB SATA , USB, 3.0 Surveillance Hard Disk All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 30 | Supply, Instalation, Testing & Communicationing of BIS Compliance professional series Diagonal Screen size 43\\" LED with Resolutioin 3,840 x 2,160 (4K UHD) along with static (panel) Contrast Ratio (1300:1) or better with viewing angle of 178/178 degree with responce time of 8ms along with HDMI In 2.0-2 nos., USB 2.0-2 nos RS 232 -1 nos. With Built in Speaker (10 W + 10W ) , with high speed Processer and android or other reputated oprationg system along with 4 GB RAM along with all as per pre approved by engineer in charge. For additional technical parameter of products / work , refer Annexure \\"A\\" attached with this BSR |
| 31 | Supply & Installation of IP-20 & IK-08 , UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angles with wall mounting provision on wall. Accessories like: 1 No of 19\\" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 6 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 32 | Supply , Installation, Testing and Comissioning of Unmanaged Switch Plug-and-play - easy setup with no configuration or no software needed, following Port fast ethernet - 8 port 10/100 MBPS auto-negotiation RJ45 ports, IEEE 802.3x flow control ,supports auto-MDI/MDIX, eliminating the need for crossover cables including making connection etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 8 Port |
| 33 | Supply, Installation, & Testing of 19\\" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 6 Ports |
| 34 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with HDPE, U/UTP (Unscreened/Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Outdoor Cable as per latest ammendments of ANSI/TIA/EIA-568 C.2 & ISO/IEC 11801 2nd Ed, The copper conductors should be balanced twisted in pairs, seperated by a cross divider & protected by LSZH PVC outer jacket of UV resistant. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. Should meet IEEE 802.3af & IEEE 802.3at for POE applications. Cable Should support Ethernet 10GBASE-T according to the standards. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Please Enable Macros to View BoQ information |
