|
| 1 | Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap): 300 mm dia piles |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:(All kinds of soil) .As per DSR-2.1.1 |
| 3 | Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.As per DSR-2.27 |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).As per DSR-4.1.8 |
| 5 | Providing and injecting chemical emulsion for pre-constructional antitermite treatment and creating and chamical bariier under and arround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981) approved material such as Hepthachlor or chlordane will be used. The rate of application of chemical emulsion shall be as follows. |
| 6 | RCC work with cement approved coarse sand and 2cm. (3/4'') gauge approved stone ballast in the proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.I wire.and including necessary cantering and suttering etc and also including supply of all materials,labour and tools and plants etc. required for proper completion of the work. binding wire to be supplied by the contractor free of cost. |
| 7 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth Cement morter 1:4 .As DSR NO.- 6.1.1 |
| 8 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in Superstrecture and above plinth Cement morter 1:6 .As DSR NO.- 6.4.2 |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars.As per DSR-5.22.1 |
| 10 | CEMENT PLASTER (IN FINE SAND)12 mm cement plaster of mix :in 1:4 (1 cement: 4 fine sand).AS per DSR No.- 13.1.1 |
| 11 | CEMENT PLASTER (IN FINE SAND)15 mm cement plaster of mix :in 1:4 (1 cement: 4 fine sand).AS per DSR No.- 13.2.1 |
| 12 | 2.5 cm thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm (3/4\\") graded approved stone laid in panels finished with 3mm (1/8\\") floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and Excluding 8cm (3\\") thick base concrete consisting of cement fine sand of 1.25 fineness modulus and brick ballast 4 cm. (1½\\") gauge in the proportion of 1:4:8 and removing any overlapping mortar at the joints ofthe panels if any and giving them a uniform finish including supply of all materials, labour and tools and plants etc. required for proper completion of the work. |
| 13 | Providing and fixing glass strips of 3.15 mm (1/8\\") thickness in joints of floor and skirting at the time of laying floor, flush with floor including labour, tools and plants etc. complete. |
| 14 | Providng and laying of 8 to 10mm thick ivory or light shade vitrified tiles of 600mm x 600mm size in flooring or skirting laid with 1 : 3 cement mortar (1 cement , 3 coarse sand) finishing with cement sturry & with pigment grouting & Polishing complete I/C S/O all material labour T & P etc. required for proper completion of work excluding base contrete. |
| 15 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): |
| 16 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 17 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 18 | supply & Fixing of 10cm Internal dia PVC pipes complete with rose- heads, bends abd gratings & including supply of necessary M.S. clamps 2.5cmx3mm (1\\"x1/8\\") fixed to walls, with & including supply of 15cm (6\\") long 6mm (1?4\\") dia nails & including supply of all materials, labour and T&P etc required for proper completion of the work and also including repair of plaster, pointing etc if damaged during fixing of pipes, details of 30' length. |
| 19 | Supply and fixing 6mm (1/4\\") China white glazed tiles in flooring or in skirting or dado laid with ratio 1:3 cement and approved coarse sand finished with white cement slurry, jointing and polishing complete, including supply of all material, labour and tool and plants etc. required for proper cpmpletion of the work. |
| 20 | Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with requiredEPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to bepaid for separately) : For fixed portion |
| 21 | 2cm (3/4\\") thick cement plaster in dado of skirting in 12 consisting of one part of cement and two parts of approved coarse sand laid in panels, finished with 3mm 1/8\\") flooating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour and tools and plants etc. required for proper completion of the work. |
| 22 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. As per DSR No.-17.1.1 |
| 23 | Providing and fixing 550mmx400 mm. wash hand basin of white glazed earthen ware 1st quality ISI marked (Hindustan, Neyer, Cera make) with RS or CI brackets painted white, 15 mm. dia. CP brass pillar cock with CP metal handle (weigth not less than 400 gms.) ISI marked and 32 mm. dia. CP brass chain with rubber plug, 32 mm. dia. CP brass waste standard pattern with check nut 32 mm. dia. CP brass P or S trap and unions complete with PVC connection 0.50 size including supply of all required materials, labour, T&P etc. required materials labour, T&P etc. required for proper completion of work and including cutting and making good the walls and floor with cement, coarse sand and grit, fittings used should be of superior quality. |
| 24 | Providing and fixing 600 mm. x 450 mm. bevelled edge mirror of Atul, Kiron make glass with Indian polish 6.50 mm. thick complete with back of 600 mm. x 450 mm. x 6 mm. hard board sheet fixed to wooden cleats with CP brass screws and washers including supply of all materials, labour, T&P etc. required for proper completion of the work. |
| 25 | Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials, labour, T&P etc. required for proper completion of the work. |
| 26 | Supply and fixing Nahani Trap Indian make of approved heavy quality complete with CP brass grating, Nahani trap laid over base cement concrete 1:6:12 including supply of all materials, labour, T&P etc. required for proper completion of the work. |
| 27 | Providing and fixing 750 mm. x 20 mm. size CP brass towel rail of approved quality (weight 275 gms. Including brackets) with a pair of CP brass brackets (to fit the size of towel rail) fixed on the wall on wooden cheats with CP brass screws including supply of all materials, labour, T&P etc. required for proper completion of the work and cutting and making good the wall plaster etc. required for the work. |
| 28 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(15 mm nominal dia Pipes).Asper DSR No.-18.7.1 |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(25 mm nominal dia Pipes).Asper DSR No.-18.7.3 |
| 30 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.As per DSR No.- 18.51.1 |
| 31 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.As per DSR No.- 18.52.1 |
| 32 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.As per DSR No.- 18.48 |
| 33 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal boreAs per DSR No.- 18.18.3 |
| 34 | Providing and fixing 25 mm. dia. PVC ball float valve with barss rod and union complete ISI marked including supply of all materials, labour and T&P etc. required for proper completion of the work. |
| 35 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore.As per DSR No.- 18.17.2 |
| 36 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.As per DSR No.- 17.22.A |
| 37 | Providing & fixing Soap Dispenser with Metallic bottle i/c all cost of material ,labour T&P etc all complete. |
| 38 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.As per DSR No.- 18.65 |
| 39 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.As Per DSR No.8.2.2.1 |
| 40 | Providing and fixing sand cast iron jali (grating) for floor/nahani trap. 100mm dia |
| 41 | Providing & fixing Wash basin mixture including all lobour etc complete 15mm nominal bore |
| 42 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern .DSR No. - 17.4.3 |
| 43 | Providing and fixing Acrylic letters with light 1.5 feet hight i/c all cost of material ,labour T & P etc all complete. |
| 44 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid As per DSR No.-17.3.1 Please Enable Macros to View BoQ information |
