|
| 1 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable etc. as required (Ref to DSR 1.8) |
| 2 | Group B (Ref to DSR 1.8.2) |
| 3 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. (Ref to DSR 1.17) |
| 4 | 3 x 2.5 sq. mm (Ref to DSR 1.17.12) |
| 5 | 3 x 4 sq. mm (Ref to DSR 1.17.21) |
| 6 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in urface/recess including cutting the wall and making good the same in case of recessed conduit as required (Ref to DSR 1.21) |
| 7 | 25mm (Ref to DSR 1.21.2) |
| 8 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required (Ref to DSR 1.23) |
| 9 | 5/6 A switch (Ref to DSR 1.23.1) |
| 10 | 3 pin 5/6 A socket outlet (Ref to DSR 1.23.4) |
| 11 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required (Ref to DSR 1.30) |
| 12 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (Ref to DSR 2.4) |
| 13 | 4 way (4 + 12), Double door (Ref to DSR 2.4.1) |
| 14 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Ref to DSR 2.10) |
| 15 | Single pole (Ref to DSR 2.10.1) |
| 16 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V \\"C\\" curve DP MCB complete with connections, testing and commissioning etc. as required. (Ref to DSR 2.16) |
| 17 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.( Ref:-2.6) |
| 18 | All kinds of soil ( Ref:-2.6.1) |
| 19 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: (Ref 5.9) |
| 20 | Foundations, footings, bases of columns, etc. for mass concrete. (ref 5.9.1) |
| 21 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : (Ref 5.1) |
| 22 | 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) (Ref 5.1.2) |
| 23 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete in all respect. (Ref 5.22.6) |
| 24 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tappingnscrews of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (ref 12.50) |
| 25 | 12 mm cement plaster of mix: (Ref 13.2) |
| 26 | 1:6(1cement:6fine sand) (Ref 13.2.1) |
| 27 | Providing & laying P.C.C. 1:8:16 (1 Cement : 8 coarse sand: 16 coarse aggregate)with stone ballast 32mm guage in foundation and plinth. Complete in all respect to the entire satisfaction of the EIC. (Ref N.S.) |
| 28 | Providing and laying Brick work with F.P.S. bricks of class designation 100 (average compressive strength not less than 105 kg per sq.cm.) in Foundation and plinth in : (Ref N.S.) |
| 29 | Cement mortar 1:6 (1cement: 6 coarse sand) (Ref N.S.) |
| 30 | Providing and laying Brick work with F.P.S. bricks of class designation 100 (average compressive strength not less than 105 kg per sq.cm.) in superstructure above plinth level up to floor V level in all shapes and sizes in :.(Ref N.S.) |
| 31 | Cement mortar 1:6 (1cement: 6 coarse sand) (Ref N.S.) |
| 32 | Providing and fixing of 4mm thick (G.I. wire) hot dip G.I. chain link fabric fencing in diamond mesh size 50x50mm to be fixed on steel frame with 20x5mm MS flat with 50x5mm self drilling screws, washers etc. complete with cutting, drilling, grinding, welding, painting of MS Flat etc. complete as per the direction of E.I.C. (Ref N.S.) |
| 33 | Providing & fixing MS Steel door to be erected from angle iron chowkhats/ frames 40x40x6mm and door shutter frame of 35x35x5mm along with 16 gauge of CRC sheet press to corrugation (if required). complete in all respects along with all necessary fittings such as iron hinges, sliding bolts, screws and handles of required size etc. with one coat of steel primer and two coats of approved synthetic enamel paint. complete in all respect to the entire satisfaction of the engineer-in-charge. (Ref N.S.) |
| 34 | Providing and making of Steel work welded in built up sections/ framed work, openable shutter barricades and mid height gates including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coats of approved synthetic enamal paint. complete in all respect to the entire satisfaction of the Engineer-in-Charge.(Ref.N.S.) |
| 35 | Providing and fixing of 6mm insulated aluminium foil finished polyprolene sheet including cutting to size and shape wherever required. (Ref N.S.) |
| 36 | Supplying and fixing 100W socket type 5 step fan regulator on existing plate with all petty materials complete in all respect to the entire satisfaction of the EIC. (Ref N.S.) |
| 37 | Supply and Erection of Exhaust Fan (Heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making good the damage, carriage chaarges, connection, testing, commissioning etc as required to complete the job to the entire satisfaction of the EIC. (Ref N.S.) |
| 38 | 380MM Sweep 900RPM with louver |
| 39 | Supply, Installation, Testing and Commissioning of 4 feet long extruded aluminium LED batten fixture 40W, CCT-6500K complete in all respect to the entire satisfaction of the EIC. (Ref N.S.) Please Enable Macros to View BoQ information |
