|
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Ordinary rock |
| 3 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, deth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level |
| 5 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 8 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick |
| 9 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 2nd class teak wood beading 62X19 mm |
| 10 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 11 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat |
| 12 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 13 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 15 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 16 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 17 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand) |
| 18 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 19 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 20 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 21 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 22 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore |
| 23 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead |
| 24 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White |
| 25 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe |
| 26 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : Sand cast iron S&S pipe as per IS: 1729 |
| 27 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 75 mm dia pipe |
| 28 | Providing and fixing bend of required degree with access door, insertionrubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Sand cast iron S&S as per IS - 1729 |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 30 | 20 mm nominal dia Pipes |
| 31 | 25 mm nominal dia Pipes |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 80 mm nominal dia Pipes |
| 33 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore |
| 34 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 35 | 25 to 40 mm nominal bore |
| 36 | 50 to 80 mm nominal bore |
| 37 | Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore |
| 38 | Providing and filling sand of grading zone V or coarser grade, allround theG.I. pipes in external work : |
| 39 | 40 mm diameter pipe |
| 40 | 80 mm diameter pipe |
| 41 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 42 | 15 mm nominal bore |
| 43 | 20 mm nominal bore |
| 44 | 25 mm nominal bore |
| 45 | 40 mm nominal bore |
| 46 | 80 mm nominal bore |
| 47 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 48 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball |
| 49 | 20 mm nominal bore, 120 mm long, weighing not less than 198 gms |
| 50 | 25 mm nominal bore, 152 mm long, weighing not less than 440 gms |
| 51 | Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks |
| 52 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 53 | For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 54 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 55 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 56 | P/F CPVC F.T.A./ M.T.A. (Brass Insert) with reducer sokit 25 mm dia. of approved quality (Supreme make or equalent) |
| 57 | Providing and fixing C.P. brass angle valve 15 mm nominal bore (Make Cera cat no. F2008201 or equivalent of Jaquar, Kohler, Grohe ) |
| 58 | Repair the damaged GI pipe line with required GI pipe and fittings etc complete as per direction of Engineer –in-charge 25 mm nominal bore. |
| 59 | P/F CP brass 2-way Bib cock/ angle valve with single handle and wall flange 15 mm nominal bore of approved make (Make Cera cat no. F2002211 or equivalent of Jaquar, Kohler, Grohe ) |
| 60 | Providing and fixing CP brass overhead shower (Make Cera cat no. F-7020108AB or equivalent of Jaquar, Kohler, Grohe ) overhead shower 80 mm dia with 200 mm long shower arm and wall flange etc complete.in all respect. |
| 61 | P/F CPVC F T A/ M T A with reducer sokit 20 mm dia. of approved quality (Supreme make or equalent) |
| 62 | Providing and fixing a custem-built cupboard with total over all depth of 600 mm. The main structure of the cupboard including the sides, top, bottom, shelves and shutters shall be febricated using 18 mm thick HDHMR (one side prelemineted ) bord of approved brand such as Action, Tesa, Green ply, or century. The rear pennal shall be made from 8 mm thick HDHMR (one side prelemineted ) the exteror must be coverd with sunmica as well the sunmica shall be of approved brand only. The scope includes supplying ans installing all necessary hardwere fittng and fixtures, such as hinges, handels, Godrej multipurpose locks, stopers, screws and other accessories. The entire work shall be carried out as per the instructions of the Engineer in-charge, ensuring proper allgnment, finishing and durability. (Note:- For the purpose of payments only the frunt face area of the cupboard will be mesured in squire metres, internal details will not be measured separately.) |
| 63 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore (Make Cera cat no. QT F-2006152 or equivalent of Jaquar, Kohler, Grohe ) |
| 64 | P/F hand shower (Health Facuet) (ABS Body) with 8 mm dia 1 meter long flexible tube and wall hook (Make Cera cat no.F8030108AB or equivalent of Jaquar, Kohler, Grohe ) complete.in all respect. |
| 65 | P/F CP brass wall mixer of approved quality with necessary taflon tape, washer etc all complete. (Make Cera QT F2006404 HT F3001404 or equivalent of Jaquar, Kohler, Grohe ) Wall mixer with telephonic shower arrangement. |
| 66 | P/F 19 mm thick Commercial board (Duro make and equalent of Greenply, Century) with necessary nails, adhesive etc all complete. |
| 67 | P/F CPVC ball valve 25 mm dia. of approved quality (Supreme make or equalent) |
| 68 | P/F 15 mm CP brass pillar cock (Make Cera cat no. QT F2006101 or equivalent of Jaquar, Kohler, Grohe). |
| 69 | P/F CPVC F T A/ M T A with reducer sokit 50 mm dia. of approved quality (Supreme or equalent Finolex, Astral) |
| 70 | Repair the damaged GI pipe line with required GI pipe and fittings etc complete as per direction of Engineer –in-charge 25 mm nominal bore. |
| 71 | Providing and fixing 100 mm dia corregated sewage discharge pipe (suction pipe) including necessary fittings, jubliee clamps, socket etc complete as per the direction of Engineer-in-charge Please Enable Macros to View BoQ information |
