Tender For Annual Maintenance, Repairs And Other Emergent Works Of Various W.S.Schemes Under The Jurisdiction Of Phe Sub Division Sumbal Of Jal Shakti Phe Division Sopore For The Financial Year 2026 -2027 Under M&R., Sopore-Jammu And Kashmir

TDR : 54676683

Tender Notice
BOQ

20 Days Left

Sopore , Jammu And Kashmir

Tender Brief : Tender For Annual Maintenance, Repairs And Other Emergent Works Of Various W.S.Schemes Under The Jurisdiction Of Phe Sub Division Sumbal Of Jal Shakti Phe Division Sopore For The Financial Year 2026 -2027 Under M&R.

Document Fees
₹ 1500 /-

EMD
₹ 40000.0 /-

Tender Value
₹ 20 Lakhs /-

Submission Date
06-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 1 meter from cutting edge
2	In all kinds of soils
3	Ordinary rock
4	Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.
5	In all kinds of soils
6	Ordinary rock
7	Hard Rock (Requiring Blasting )
8	Hard Rock (Blasting Prohibited)
9	Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:
10	In all kinds of soils
11	Ordinary rock
12	Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earthlead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.
13	In all kinds of soils
14	Ordinary rock
15	Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.
16	Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.
17	Beyond 30 cm girth upto and including 60 cm girth.
18	Beyond 60 cm girth upto and including 120 cm girth.
19	Beyond 120 cm girth upto and including 240 cm girth.
20	Above 240 cm girth
21	Providing & fixing upto floor five level precast cement concrete hollow blocks, including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete.
22	1:1½:3(1 cement :1½ coarse sand :3 graded stone aggregate 20 mmnominal size)
23	1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)
24	1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)
25	Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement)
26	Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 (1 cement: 3 fine sand) including curing.
27	Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)
28	Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:Cement mortar 1:6 (1 Cement : 6 coarse sand)
29	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
30	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class kail
31	Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete
32	popular wood
33	First class Budloo/Fir wood
34	Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete.With 2nd class teak wood beading 62x19 mm
35	Providing and fixing specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) :Flat pressed 3 layer particle board or graded wood particle board IS:3087 18 mm
36	Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class Kail wood
37	Providing and fixing cupboard shutters 25mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade I Type II) having one side decorative lamination and other side a balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and bright finished stainless steel piano hinges complete as per directions of Engineer- in-charge
38	Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-inchargeInternal work-exposed on wall with clamps at 1.00 meter spacing
39	PN-16 pipe, 16mm OD(SDR-7.4)
40	PN-16 pipe , 20mm OD(SDR-7.4)
41	PN-16 pipe , 25mm OD(SDR-7.4)
42	PN-16 pipe , 32mm OD(SDR-7.4)
43	PN-16 pipe , 40mm OD(SDR-7.4)
44	PN-10 pipe , 50mm OD(SDR-11)
45	Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.
46	PN-16 pipe, 16mm OD(SDR-7.4)
47	PN-16 pipe , 20mm OD(SDR-7.4)
48	PN-16 pipe , 25mm OD(SDR-7.4)
49	PN-16 pipe , 32mm OD(SDR-7.4)
50	External work including trenching, refilling etc
51	PN-16 pipe, 16mm OD(SDR-7.4)
52	PN-16 pipe , 20mm OD(SDR-7.4)
53	PN-16 pipe , 25mm OD(SDR-7.4)
54	PN-16 pipe , 32mm OD(SDR-7.4)
55	PN-10 pipe , 50mm OD(SDR-11)
56	PN-10 pipe , 50mm OD(SDR-11)
57	PN-10 pipe , 63mm OD(SDR-11)
58	PN-10 pipe , 75mm OD(SDR-11)
59	PN-10 pipe , 90mm OD(SDR-11)
60	PN-10 pipe , 110mm OD(SDR-11)
61	PN-10 pipe , 160mm OD(SDR-11)
62	Providing and fixing PPR Unions
63	PPR Union 20mm
64	PPR Union 25mm
65	PPR Union 32mm
66	PPR Union 40mm
67	PPR Union 50mm
68	PPR Union 63mm
69	PPR Union 75mm
70	Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work.
71	100 mm and 150 mm dia GI pipes
72	65 mm and 80 mm dia GI pipes
73	40 mm and 50 mm dia GI pipes
74	25 mm and 32 mm dia GI pipes
75	15 mm and 20 mm dia GI pipes
76	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
77	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge :
78	Above 40 mm nominal bore
79	15 - 40 mm nominal bore
80	Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe)
81	Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket.
82	100 mm dia pipes
83	125 mm dia pipes
84	150 mm dia pipes
85	200 mm dia pipes
86	250 mm dia pipes
87	300 mm dia pipes
88	Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) light class
89	20 mm dia. nominal bore
90	25 mm dia. nominal bore
91	Providing and fixing imported wooden panelling 15mm thick over framming work of required pattern and design water proof strips of ply board for celiling/walling (imported wood/RAIT wood) incl ply wood framing.
92	Providing and applying touch-up wood polish on existing wooden surfaces, including sanding, filling minor cracks/imperfections, and applying 1-2 coats of approved synthetic enamel or wood polish, complete in all respects as directed by the Engineer-in-Charge.
93	Providing and fixing imported PVC panelling (8 to 10 mm Thick) of Approved make pattern including the base work of Gl channels with necessary screws and cornice at the edge with all carriages all complete as per the directions of incharge engineer at site.
94	Providing and fixing of wooden flooring of approved brand and fixing of 2 mm foam underneath the flooring with heatex solution including cost and carriage of all materials involved complete job.
95	Providing and Construction of 24'-0\\" deep Almirah made of plywood (18mm) with face of teak including cost of all hardware items of approved quality complete job.
96	Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
97	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
98	White washing with lime to give an even shade on Old Work (two or more coats)
99	Colour washing such as green blue or buff to give an even shade
100	New work (two or more coats) with a basecoat of white washing with lime.
101	New work (two or more coats) with basecoat of whiting
102	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer
103	Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications
104	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.
105	Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat.
106	Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)
107	Applying priming coat: With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood
108	Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works
109	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work
110	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
111	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On steel work
112	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On concrete work
113	Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work
114	With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter
115	With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter
116	Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including skirting in vertical, rubbing, polishing and curing complete with: Makrana White Second quality (16mm)
117	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters: 80x1.25 mm M.S. laths with 1.25 mm thick top cover
118	80x1.25 mm M.S. laths with 1.25 mm thick top cover
119	80x1.20 mm M.S. laths with 1.20 mm thick top cover
120	80x0.90 mm M.S. laths with 0.90 mm thick top cov
121	Providing and fixing ball bearing for rolling shutters.
122	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete
123	Upto 40mm Nominal Bore
124	Above 40mm Nominal Bore
125	Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.
126	Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix)
127	Demolishing RCC work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-incharge
128	Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
129	Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
130	Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)
131	Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
132	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
133	Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate.
134	Carriage of material from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport
135	Cement & steel, G.I/C.I pipe avg. lead upto 01 Kms
136	Cement & steel, G.I/C.I pipe avg. lead upto 02 Kms
137	Cement & steel, G.I/C.I pipe avg. lead upto 03 Kms
138	Cement & steel, G.I/C.I pipe avg. lead upto 04 Kms
139	Cement & steel, G.I/C.I pipe avg. lead upto 05 Kms
140	Cement & steel, G.I/C.I pipe avg. lead beyond 5 Kms upto 10 Kms (per Km)
141	Cement & steel, G.I/C.I pipe avg. lead beyond 10 Kms upto 20 Kms (per Km)
142	Cement & steel, G.I/C.I pipe avg. lead beyond 20 Kms per additional Km
143	Sand & Agg. 20 mm avg. lead of upto 01 Kms
144	Sand & Agg. 20 mm avg. lead upto 02 Kms
145	Sand & Agg. 20 mm avg. lead upto 03 Kms
146	Sand & Agg. 20 mm avg. lead upto 04 Kms
147	Sand & Agg. 20 mm avg. lead upto 05 Kms
148	Sand & Agg. 20 mm avg. lead beyond 5 Kms upto 10 Kms (per Km)
149	Sand & Agg. 20 mm avg. lead beyond 10 Kms upto 20 Kms (per Km)
150	Sand & Agg. 20 mm avg. lead beyond 20 Kms per additional Km
151	40 mm Agg. avg. lead of upto 01 Km
152	40 mm Agg. avg. lead upto 2 Kms
153	40 mm Agg. avg. lead upto 3 Kms
154	40 mm Agg. avg. lead upto 4 Kms
155	40 mm Agg. avg. lead upto 5 Kms
156	40 mm Agg. avg. lead beyond 05 Kms upto 10 Kms (per Km)
157	40 mm Agg. avg. lead beyond 10 Kms upto 20 Kms (per Km)
158	40 mm Agg. avg. lead beyond 20 Kms per additional Km
159	Stone soiling avg. lead of upto 1 Km
160	Stone soiling avg. lead upto 2 Kms
161	Stone soiling avg. lead upto 3 Kms
162	Stone soiling avg. lead upto 4 Kms
163	Stone soiling avg. lead upto 5 Kms
164	Stone soiling avg. lead beyond 05 Kms upto 10 Kms (per Km)
165	Stone soiling avg. lead beyond 10 Kms upto 20 Kms (per Km)
166	Stone soiling avg. lead beyond 20 Kms per additional Km
167	Carriage of pipes from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport
168	100 mm and 125 mm dia DI/ GI pipes 1Km
169	100 mm and 125 mm dia DI/ GI pipes 2Km
170	100 mm and 125 mm dia DI/ GI pipes 3Km
171	100 mm and 125 mm dia DI/ GI pipes 4Km
172	100 mm and 125 mm dia DI/ GI pipes 5Km to 10 Km
173	100 mm and 125 mm dia DI/ GI pipes 10Km to 20 Km
174	100 mm and 125 mm dia DI/ GI pipes beyond 20 Km every additional lead
175	150 mm to 200 mm dia DI pipes 1 Km
176	150 mm to 200 mm dia DI pipes 2 Km
177	150 mm to 200 mm dia DI pipes 3 Km
178	150 mm to 200 mm dia DI pipes 4 Km
179	151 mm to 200 mm dia DI pipes 5 Km
180	150 mm to 200 mm dia DI pipes 5Km to 10Km
181	150 mm to 200 mm dia DI pipes 10Km to 20Km
182	150 mm to 200 mm dia DI pipes beyond 20Km for every additional lead
183	Centering and shuttering including strutting, propping etc, and removal of form for.
184	Foundations, footings, bases of columns etc for mass concrete.
185	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.
186	Columns, pillars, piers, abutments, posts and struts.
187	Suspended floors, roofs, landings, balconies and access platforms.
188	Lintel, beams, plinth beams, girders, bressumers and cantilevers.
189	Stairs (excluding landings) except spiral staircases.
190	Edges of slabs and breaks in floors and walls under 20cm wide
191	Extra for shuttering in circular work (20% of respective centring and strutting items)
192	Clearing snow (without frost) from roads manually.
193	Snow depth upto 150 mm
194	Snow depth over 150 mm but upto 250mm
195	Snow depth over 250 mm but upto 350mm
196	Snow depth over 350 mm but upto 450mm
197	Clearing snow (with frost) from roads, manually using picks and shovels; snow depth upto 150 mm
198	Clearing snow avalanche mixed with frost and compressed snow, including all types of equipments and safety to the workers while clearing the avalanches at head site
199	Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) Quarry
200	Dry random rubble masonry with hard stone in foundation and plinth: With bond stone. (Nallah)
201	Renewing glass panes and re-fixing existing wooden fillets: Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
202	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
203	Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded
204	Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
205	In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.
206	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
207	Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.
208	M.S. tube
209	E.R.W. tubes
210	G.I. pipes
211	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,
212	Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete.
213	Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
214	Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4 mm aperture on both sides.
215	Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.
216	In colour such as White, Ivory, Grey, Fume Red Brown
217	In all colours, shades, except White, Ivory, Fume Red Brown
218	Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2
219	Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.
220	1.00 mm thick with zinc coating not less than 275 gram/m2
221	Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2
222	Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes
223	75 mm diametre
224	110 mm diametre
225	12mm Cement plaster finished with a floating coat of neat cement of mix:
226	1 : 3 ( 1 cement : 3 fine sand)
227	1 : 4 ( 1 cement : 4 fine sand)
228	Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
229	Renewing glass panes, with wooden fillets wherever necessary :
230	Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)
231	Providing and Laying of Stone Soling Hand Packed and compacted manually including all carriages complete
232	Good Earth
233	Moorum
234	Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge.Made of G.I. wire of dia 4 mm
235	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
236	Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931
237	Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931
238	Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc. if required will be paid separately).
239	50 mm dia
240	80 mm dia.
241	100 mm dia.
242	Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately)
243	80 mm dia. nominal bore
244	100 mm dia. nominal bore
245	150 mm dia. nominal bore
246	200 mm dia. nominal bore
247	Providing and laying D.I. Specials of Class K-12 suitable for push-on jointing as per IS : 9523
248	Upto 600 mm dia.
249	Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. One coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.
250	Weed clearance
251	From lakes(using boats)
252	From canals(including extraction of roots)
253	Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion
254	Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) 22.1.1.2 Powder coated aluminum (minimum thickness of powder coated 50 microns)
255	Powder coated aluminum (minimum thickness of powder coated 50 microns)
256	Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)
257	For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) 22.1.2.2 Powder coated aluminum (minimum thickness of powder coated 50 microns)
258	Powder coated aluminum (minimum thickness of powder coated 50 microns)
259	Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)
260	Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge.
261	Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.
262	Pre-laminated particle board with decorative lamination on both sides
263	Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic items)
264	With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)
265	With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)
266	With float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm)
267	Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.
268	Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 meters.
269	Upto 150 mm diameter.
270	Above 150 mm diameter.
271	Dismantling C.I. pipes manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes and lead at site within 50 meter lead as per direction of Engineerin-charge
272	Upto 150 mm diameter.
273	Above 150 mm diaupto 300 mm dia.
274	Cutting road and making good the same including supply of extra quantities of material i.e. crushed aggregate, moorum screening, red bajri and labour required.
275	Water bound macadam.
276	Bituminous portion
277	Labour for cutting C.I. pipe with steel saw.
278	80 mm diameter C.I. pipe
279	100 mm diameter C.I. pipe
280	125 mm diameter C.I. pipe
281	150 mm diameter C.I. pipe
282	200 mm diameter C.I. pipe
283	250 mm diameter C.I. pipe
284	Hand-packing stones in wire-crates; excluding cost of crates and stones
285	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead.
286	For thickness of tiles 10 mm to 25 mm
287	For thickness of tiles above 25 mm and upto 40 mm.
288	Supply of Pig Lead at site of work
289	Providing and fixing basin mixer of approved quality.
290	Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia
291	Providing and fixing CP Brass tapes of quality & make as approved by Engineer in charge. 15 mm nominal dia
292	Providing and fixing P.V.C low level flushing cistern with manually18.0 (Sanitary Installation) 240 CODE NO. DESCRIPTION UNIT RATE ₹ controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 litre capcity -white
293	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto/above plinth level
294	Thermo-Mechanically Treated bars of grade Fe-500D or more.
295	Providing and fixing 1st quality ceramic glazed floor/ wall tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
296	Supply and Installation of acrylic Boards 5 mm thick with laser cut etc. complete Job
297	Dismantling of spindle / rod and check nuts of flanged type sluice valves by way of manufacturing of new spindle / rod made out of mild steel & new check nut made out of gun metal material. The job includes dismantling of sluice valve reassembling after fixing of spindle & check nut duly manufactures and threaded in workshop including cost of welding, packing, carriage to & fro upto the workshop and back to site of work (Complete job) from 80 mm dia sluice valve upto 300 mm dia sluice valve including cost of salvaged material.
298	Providing / fixing of M.S double collers/ arresting of leakages by way of welding including all sorts of carriages
299	80 mm dia
300	100 mm dia
301	150 mm dia
302	200 mm dia
303	Providing / fixing of double collers, G.I./ M.S. for arresting of leakages by using led & spun yarn incld. earthwork excavation, refilling etc. including all sorts of carriages (length verying from 0.60 to 1 Mtr.)
304	40 mm dia
305	50 mm dia
306	65 mm dia
307	80 mm dia
308	100 mm dia
309	150 mm dia
310	200 mm dia
311	Providing and fixing including testing, commissioning & fabricating at site M.S pipe Specials Etc. & all sorts of carriages upto site of work, as per requirement at site complete job.
312	Providing and fixing of Electrical points (heating and lighting) incld. cost of wire switches, necessary MCB’s switch boards, ceiling roses reputed make ISI mark screws, casing / conduit materials of allsorts of carriage and labour charges required for the job.
313	Lighting points
314	Heating points
315	Supply/ fixing of pipe specials from open market, if not available in the Divisional stores of ISI marked standard make.
316	100 mm dia G.I Union
317	80 mm dia G.I Union
318	65 mm dia G.I. Union
319	50 mm dia G.I. Union
320	40 mm dia G.I. Union
321	25 mm dia G.I. Union
322	20 mm dia G.I. Union
323	80 mm dia G.I. Elbow
324	65 mm dia G.I. Elbow
325	50 mm dia G.I. Elbow
326	40 mm dia G.I. Elbow
327	25 mm dia G.I. Elbow
328	20 mm dia G.I. Elbow
329	80 mm dia G.I. Socket
330	65 mm dia G.I. Socket
331	50 mm dia G.I. Socket
332	40 mm dia G.I. Socket
333	25 mm dia G.I. Socket
334	20 mm dia G.I. Socket
335	80 mm dia G.I. Nipple upto 10\\"
336	65 mm dia G.I. Nipple upto 10\\"
337	50 mm dia G.I. Nipple upto 10\\"
338	40 mm dia G.I. Nipple upto 10\\"
339	25 mm dia G.I. Nipple upto 10\\"
340	20 mm dia G.I. Nipple upto 10\\"
341	15 mm dia G.I. Nipple upto 10\\"
342	25x25x20 mm dia G.I. Equal Tee
343	40x40x25 mm dia G.I. Equal Tee
344	50x50x40 mm dia G.I. Equal Tee
345	65x65x50 mm dia G.I. Equal Tee
346	80x80x65 mm dia G.I. Equal Tee
347	25x20 mm dia Socket/ Reducer
348	40x25 mm dia Socket/ Reducer
349	50x40 mm dia Socket/ Reducer
350	65x50 mm dia Socket/ Reducer
351	80x65 mm dia Socket/ Reducer
352	25x20 mm dia Elbow/ Reducer
353	40x25 mm dia Elbow/ Reducer
354	50x40 mm dia Elbow/ Reducer
355	65x50 mm dia Elbow/ Reducer
356	80x65 mm dia Elbow/ Reducer
357	100mm dia Elbow
358	100mm dia Equal Tee
359	100 mm dia G.I. Bend
360	80 mm dia G.I. Bend
361	65 mm dia G.I. Bend
362	50 mm dia G.I. Bend
363	40 mm dia G.I. Bend
364	Supply of Kerosene oil/Transformer oil including all carriages
365	Providing refreshment to officals/guests and the partcipants of the Indenpadnace Day , Republic day or other official Functions complette job including packing at venue with following Menu, incluidng serving charges/ carry bags
366	Water Bottle One litre
367	Water Bottle 500 ml
368	Water bollte 250 ml
369	Juice pac/ tin 100 ml to 180 ml of Standard Quality
370	Boiled Egg
371	Biscuit standard Quality of 50 g
372	Dal 50 g Pac
373	Banana
374	Butter Toastes each pair
375	Toastes without Butter each pair
376	Tea Sugar each Cup
377	Tea Namkeen each Cup
378	Re-threading of damaged pipe ends including carriage from site to workshop and back.
379	20 mm dia
380	25 mm dia
381	40 mm dia
382	50 mm dia
383	65 mm dia
384	80 mm dia
385	100 mm dia
386	Dismentalling of backwash motors/ Alum motors/ bleaching motors of filtration plants by way of rewinding of core made out of copper metal fiber superior type of required thickness and guage. The job includes replacing of bearings, water seal, nuts, bolts, rubber washers and painting of instruments. The job also includes all sorts of carriage from site to work upto workshop to & fro including testing & commissioning of following capacity.
387	For 0.50 HP to 2.00 HP
388	For 3.00 HP to 5.00 HP
389	For 5.00 HP to 10.00 HP
390	Dismentalling of complete reduction gear unit of de-sludge bridges for repairs by way of providing & manufacuring of complete reduction gear with hub. The job includes costing of brass material, grinding & finishing of virme in order to make the new teeth, replacement of damaged oil seals by way of new one, replacemnet of ball bearings, pouring of required specific gravity ear oil in order to run the reduction gear in smooth order, refixing of same at the site of work incld. all sorts of carriage fro site of work upto workshop and back to site of work including testing & successful commissioning (complete job)
391	Overhauling voltage stabilizers installed at site. The job includes pouring / filling of transformer oil of required specified gravity, replacement of driven rotars (automatic), replacement of voltage meters, Amp meters, indicators, thimbles etc. complete job, making the unit complete functional for bearing of required load. The job also includes labour charges, cost of wiring, pin sockets and all sorts of carriages from site of work upto the workshop & back to actual site of work incld. installation at site & testing, successful commissioning complete job.
392	5 KV to 10 KV
393	11 KV to 20 KV
394	21 KV to 30 KV
395	Providing and fitting at site 3-phase, Voltage stabilizer 30 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job.
396	Providing and fitting at site 3-phase, Voltage stabilizer 25 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job.
397	Supply and filling of filter media from approved source - Gravel (Graded gravel - size ranging from 2.0mm to 40.00 mm) in filter beds. Including all carriages, complete job
398	Supply and filling of filter media from approved source - Sand (Coarse filter sand - in filter beds. Including all carriages, complete job
399	Bore Packing: All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent.
400	Desilting of various structures incld. Disposal of desilted material from site premises with all carriages lead & lifts etc. The job also includes, washing and cleaning of walls, beds, drains and floor etc with bleaching powder solution complete job.
401	Using buckets, ropes etc. Manually
402	Through washout by Mix silt with water
403	Replacement / supply of PVC gate valves for bleaching / alum tanks/ Foot valves and PVC pipes of ISI marked standard make
404	20 mm dia Gate valve
405	25 mm dia Gate valve
406	32 mm dia Gate valve
407	40 mm dia Gate valve
408	50 mm dia Gate valve
409	20 mm dia PVC pipe (B-class)
410	25 mm dia PVC pipe (B-class)
411	32 mm dia PVC pipe (B-class)
412	40 mm dia PVC pipe (B-class)
413	50 mm dia PVC pipe (B-class)
414	80 mm dia PVC pipe (B-class)
415	100 mm dia PVC pipe (B-class)
416	Replacement of old damaged G.I. Gate valves by Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) and providing of check certificate from the standard manufacturer.
417	25 mm nominal bore
418	20 mm nominal bore
419	32 mm nominal bore
420	40 mm nominal bore
421	50 mm nominal bore
422	65 mm nominal bore
423	80 mm nominal bore
424	Supply of CFL Bulbs for filtration plant sites etc.
425	20W CFL
426	15W CFL
427	12W CFL
428	9W CFL
429	Welding, including transportation of plant at site etc. complete
430	By gas plant
431	By electric plant
432	Plugging of leakages of pipes at spots with welding around only by electric welding plant including all carriages upto site of work excluding cost of Earthwork and refilling including hire charges of welding plant.
433	65 mm/80mm dia pipe
434	100 mm /125 mm dia pipe
435	150 mm / 200 mm dia pipe
436	Hire charges for welding plant for necessary repairs of pipe network/structures etc as per requirement including C/O operator, Genrator, welding rods, wiring and carriage of man and machinary complete in all respects as per requirement at site but excluding additional materials like collar, pipe specials, steel section etc.
437	Providing / fixing of M.S. step collers from 100 mm to 450 mm dia including all sorts of carriages, complete
438	Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge
439	Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). 16.67.1 Overhead informatory road signage.
440	Supply and fixing of Inaugration stone of Marble/Granite with custom carved letters complete including Making of Foundation made out of Brick work including 15mm thick Plater in 1:4 Mix including all sorts of carriages wherever required
441	Providing and fixing of printed PVC type flex banners as per requirement complete job
442	Without the supporting frame of steel rolled hollow Sq. bars
443	With the supporting frame of steel rolled hollow Sq. bars
444	With the supporting frame of steel rolled hollow Sq. bars and cardboard backing
445	Supply of unskilled labours
446	Supply of skilled labour
447	Supply of Carpenter 2nd class
448	Supply of Mason 2nd class
449	Providing / Fixed of GI barbed wire weight 9.3 Kg per 100m (min) between two ports fitted and fixed with GI staples on wooden plugs or GI binding wire tied to 6mm bar nibs, Complete Job
450	Repairs to barbed wire fencing, complete job
451	Providing and Fixing of M.C.C.B.of ISI marked standard make the job includes dismantling of damaged/non functional Amp. M.C.C.B. and fixing of new one including all sorts carriage from source to workshop including carriages of salvaged material from filtration plant upto Divisional Stores including testing, installing and commissioning complete job
452	03 Pole 200 Amp.
453	03 Pole 100 Amp.
454	04 Pole 100 Amp.
455	02 Pole 32 Amp.
456	03 Pole 32 Amp.
457	04 Pole 32 Amp.
458	63 Amp 04 pole change over
459	3.5 core cable 50 mm thick
460	Providing and Fixing of 5-10 H.P. Starter of of ISI marked standard Make, the job includes dismantling of damaged /non functional starter and fixing of new one incl. all sorts of carriages from source to workshop including carriages of salvaged materials from filtration plant upto Divisional Stores, including testing, installing and commissioning complete job.
461	Providing and Fixing of running V-Belt of groove type for air blower, the job includes dismantling damages ones and fixing of new ones incl. successful testing, commissioning. All types of carriage complete
462	Providing fixing & commissioning of LED Flood Lights of 50 Watts with stand including all accessories required at site complete job inclusive all carriages.
463	Providing fixing & commissioning of LED Flood Lights of with stand including all accessories required at site complete job inclusive all carriages.
464	Supply of LED lights of different Wattage of approved m ake ISI marked complete in all respects
465	Providing fixing & commissioning of 10/12 mm thick Flanges in pairs including welding, cutting of threaded portion, washers including cost of Flanges with Nuts and Bolts including making joint leak proof including all sorts of labours whatsoever required
466	250mm dia
467	200mm dia
468	150mm dia
469	100mm dia
470	80mm dia
471	65mm dia
472	Restoration of damaged pipes due to frost / frozen including earth works excavation /dismantling /refilling / making good the same complete job in all respects. Upto 20mm to 100mm dia (by using blue lamp including cost of K.oil)
473	P/F of Air Releasing Valves (single acting) including cutting of bore hole , welding of the pedestal rod and providing laying of cement concrete 1:3:6 mix with shuttering box PGI 9”X9”x12” around the pedestal rod with all carriages and head load upto actual site of work
474	25mm dia Air Valve
475	20mm dia Air Valve
476	Laying & fixing of HDPE Pipes complete excluding earth work, but including all carriages upto site of work
477	25mm dia
478	32mm dia
479	40mm dia
480	50mm dia
481	Fixing charges of Sluice Valves including Testing, Commissioning and carriages from divisional store to actual site of work including dismantling of old (in case of replacement) and carriage of same to divisional store, Complete job
482	200 mm dia
483	150 mm dia
484	100mm dia
485	80mm dia
486	50mm dia
487	Engagement of JCB including haltage charges and one side POL Charges
488	Removal of dead animals from canals including disposal within 50 mts complete job
489	By Mechanical means
490	By Mannual means
491	Constructing muthu bunds, comprising boulders and wood bushes in alternate layers; including working in water situations
492	Supplying and Laying of polythene sheets (Black) at off take points during lean dscharge / Freezing
493	Opening out old wire crates those and re-binding after filling.
494	Filling empty cement bags with sand/ earth including cost of bags and earth / sand (Earth or sand to be locally excavated) including all sorts of carriages upto actual site of work
495	Silt clearance from canals Inclusive of initial lead of 50 mts and all lift Comp Job
496	Removing, washing of old filter media including washing of filter beds and laying of same in position complete job.
497	Supplying & fixing as per site requirement of Nylon rope on 10 mm dia of Standartd make including all carriages comp job
498	Hire charges of boat including charges of operator and other allied items required, complete.
499	Boat(Capacity 20 cum)
500	Providing / fixing of slip ring complete set with cliffs, bushes all accessories for clarifloculator bridge. The job includes disassembling of the damaged slipring returned back to store and fixing of new one, including all carriages.

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jammu And Kashmir Tenders

Construction Tenders

Water Storage and Supply Tenders

Water Supply Project Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Annual Maintenance, Repairs And Other Emergent Works Of Various W.S.Schemes Under The Jurisdiction Of Phe Sub Division Sumbal Of Jal Shakti Phe Division Sopore For The Financial Year 2026 -2027 Under M&R., Sopore-Jammu And Kashmir

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Annual Maintenance, Repairs And Other Emergent Works Of Various W.S.Schemes Under The Jurisdiction Of Phe Sub Division Sumbal Of Jal Shakti Phe Division Sopore For The Financial Year 2026 -2027 Under M&R., Sopore-Jammu And Kashmir

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us