|
| 1 | Pump Installation |
| 2 | OD46370/2025-2026:Supply, installation, testing, trial run and commissioning of submersible pumpset with minimum efficiency 65% capable of discharging 511 lps against total head of 6.5 mtrs, with electric motor 75 HP suitable for handling fresh and silty water with maximum rpm 1000. The material of construction of the casing NICI and impeller shall be stainless steel CF8M with Chrome steel A276 type shaft. The prime mover for the pump should be 3 phase totally enclosed water cooled motor confirming to IS 9283 , energy efficient standard rating suitable for 415V +/- 10%, 50Hz +/- 5% connection with class ?H? insulation, suitable cable confirming to IS 732:2019, length 15 m / as per site conditions. Meter board with fuse as per KSEB specification and electrical inspectorate norms, prefabricated closed type control panel board completely wired and fitted with fully automatic star delta starter, main switch with ISI mark, Ammeter, volt meter, VSS, RYB indicating lamps, 6A MCB for RYB indication lamp, HRC fuse, neutral link, ELCB, suitable capacitor, SPP, 2 nos of earth pit suitable for motor as per KSEB specification and electrical inspectorate norms, with all necessary protection units and instrumentation with MPU Panel board and 700mm Gate valve |
| 3 | 18.72.25:Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:700 mm dia Ductile Iron Class K - 9 pipes |
| 4 | 18.69.2:Providing and laying D.I Specials of Class K - 12 suitable for mechanical jointing as per IS : 9523 :Above 600 mm dia |
| 5 | 18.70.12:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:750 mm dia pipes |
| 6 | OD46419/2025-2026:Erection of 75HP Submersible Motor with pump set in correct alignment after leading them from outside of pump house to the respective foundations including cost of labour, leading charge, hire charge of equipment, tools and plants etc. complete |
| 7 | OD47644/2025-2026:Fabrication, Supply, erection and assembling by welding Stainless Steel 304L Grade as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc, lead and lift, conveyance, incidental and handling etc complete |
| 8 | OD47637/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 9 | OD47635/2025-2026:Supply of MS round bar including cost of conveyance charges |
| 10 | OD47634/2025-2026::Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platfurm and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied |
| 11 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 12 | OD47636/2025-2026:Erection of the canal shutter (Up to 2 Tonne weight) /Hoist Bridge /Platform including hand rails . lader etc for the same including, alignment correcting and setting complete including cost of all labour, machinery , incidental and conveyance, lead and lift charges etc complete but excluding cost of material already supplied. Please Enable Macros to View BoQ information |
