| 2 | SM No : 275/7051/Misc/1999 (01 Nos)1. Replace the gun metal(bronze alloy )bushesh for small up to 5 ton Each 012. Supply and installation of single phase preventer relay for protection of three-phase motor against phase failure and voltage unbalance, complete with wiring and testing as required Each 013. Providing and carrying out welding work of EOT crane hoist assembly including surface cleaning, edge preparation, alignment of parts, and welding of damaged/cracked portions of hoist frame, brackets or base using suitable electrodes (E6013/E7018) and approved welding procedure, complete with grinding, finishing, visual inspection, necessary scaffolding/arrangement, and testing to ensure proper strength and safe operation of the hoist, all as required Job 014. Supply, installation, testing of Miniature Circuit Breaker (MCB) of required rating and poles, suitable for 240/415 V, 50 Hz AC supply, with minimum 6/10 kA breaking capacity, complete with DIN rail mounting, connections and accessories as required.pe: Miniature Circuit Breaker (MCB)Standard: IS/IEC 60898-1Rated voltage: 240/415 V AC,Frequency: 50 Hz,Breaking capacity: 6 kA or 10 kA (as specified),Trip curve: B/C/D curve (as per load) Poles: SP / DP / TP / TPN (as required),Mounting: DIN railHousing: Flame retardant thermoplastic,Indication: ON/OFF trip indication Make: Havells / L&T / Schneider / Siemens or equivalent Each 025. Greasing, lubrication, inspection, and routine servicing of the crane to ensure smooth, safe, and efficient operation Hoist gearbox oil level checking and topping up .Greasing of hoist drum bearings. Wire rope lubrication with approved rope lubricant. Hook block sheave bearing greasing. Tightening of all accessible nuts and bolts.Inspection of wire rope for wear, bird caging, and corrosion. Brake gap checking and adjustment.Checking of limit switches (hoist up/down, CT, LT). Inspection of electrical panel for loose connections and overheating. Cleaning of crane, panel, and walkways and complete in all respect Job 016. Supply and fixing The 1.5 sqmm × 16 core copper cable is a multi-core flexible control cable consisting of sixteen multi-strand annealed copper conductors, each of 1.5 sqmm cross-section, individually insulated and collectively sheathed. It is mainly used for control, signalling, and pendant wiring in EOT cranes, control panels, and industrial automation systems. RM 39 |
| 3 | SM No : 275/7050/Misc/1999 (01 Nos)1. Supply ,Fixig and replacing of 63A at 415V AC-3-phase Motor Rating : 50Hz Coil Voltage: 110V AC, 50/60 Hz Each 012. Supply and fixing of old /replace 63 Amp changeover switch is a manual or automatic electrical switching device used to transfer the load supply from one power source to another, typically between the main utility (mains) and a diesel generator (DG) set. It ensures safe and reliable power continuity without back-feeding.Key Features :Current Rating : 63 AmpsPoles: Available in DP (2-pole), TP (3-pole), or TPN (4-pole)Operation: Manual lever type or automatic (ATS)Voltage Rating: Generally suitable for 415V AC, 50 Hz systems Job 01Mechanical Interlock: Prevents simultaneous connection of both sourcesMounting: Panel mounted or enclosure typeConstruction: Heavy-duty copper contacts with high insulation strength3. Supply fixing and replacing of Gun metal (Cu-Sn-Zn bronze alloy)Type: Plain sleeve bush / flanged bush (as per location)Application: Hoist drum shaft, pulley pin, hook block, trolley wheelLoad capacity: Suitable for medium to heavy duty (5-ton crane) Each 02Finish: Machined internal bore with lubrication groovesLubrication: Grease or oil lubricatedStandard: As per IS 318 / equivalent bronze 4. Greasing, lubrication, inspection, and routine servicing of the crane to ensure smooth, safe, and efficient operation ”Hoist gearbox oil level checking and topping up. Greasing of hoist drum bearings.Wire rope lubrication with approved rope lubricant. Hook block sheave bearing greasing. Tightening of all accessible nuts and bolts. Inspection of wire rope for wear, bird caging, and corrosion. Job 01 Brake gap checking and adjustment. Checking of limit switches (hoist up/down, CT, LT).Inspection of electrical panel for loose connections and overheating. Cleaning of crane, panel, and walkways.5. Supply and refilling of Hydraulic oil (ISO VG 46)in an EOT crane is used in the electro-hydraulic brake thruster, hydraulic power pack (if provided), and buffer systems. It transmits power, lubricates moving parts, prevents wear, and dissipates heat for smooth crane operation. Ltr 08 all as per above but location 167 Med regt sewage pump house- 02 shift daily Note :- The schedule credit Amt for Rs. 2770/- is fixed.Retrived material will be the property of Contractor12 Months gurantee shall be given by the contractor Please Enable Macros to View BoQ information |
